OvisLink A3GII Wireless 11n 150Mbps 3G Broadband Router User Manual

OvisLink Corp. Wireless 11n 150Mbps 3G Broadband Router

User manual

Copyright and Disclaimer AirLive GW-300NAS User’s Manual Air3GII Wireless 11n 150Mbps 3G Broadband RouterUser’s Manual
Copyright and Disclaimer AirLive Air3GII User’s Manual i Copyright The contents of this publication may not be reproduced in any part or as a whole, stored, transcribed in an information retrieval system, translated into any language, or transmitted in any form or by any means, mechanical, magnetic, electronic, optical, photocopying, manual, or otherwise, without the prior written permission. Trademarks All products, company, brand names are trademarks or registered trademarks of their respective companies. They are used for identification purpose only. Specifications are subject to be changed without prior notice. FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against radio interference in a commercial environment. This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instructions in this manual, may cause harmful interference to radio communications.
Copyright and Disclaimer AirLive Air3GII User’s Manual ii Operation of this equipment in a residential area is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures are necessary to correct the interference. CE Declaration of Conformity This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022/A1 Class B.
Table of contents AirLive Air3GII User’s Manual iii TABLE OF CONTENTS 1.INTRODUCTION ................................................................................................................................................................1 1.1 PACKING LIST ..................................................................................................................................................................2 1.2 HARDWARE INSTALLATION ..............................................................................................................................................3 2.SPECIFICATION...........................................................................................................................................................6 2.1EASY SETUP BY WINDOWS UTILITY .................................................................................................................................6 2.2 EASY SETUP BY CONFIGURING WEB PAGES...................................................................................................................13 3.INSTALLATION/ UN-INSTALLATION .........................................................................................................................17 3.1 BASIC SETTING ..............................................................................................................................................................17 3.2 FORWARDING RULES .....................................................................................................................................................35 3.3 SECURITY SETTING ........................................................................................................................................................39 3.4 ADVANCED SETTING......................................................................................................................................................47 3.5 TOOL BOX......................................................................................................................................................................56 4.TROUBLESHOOTING .....................................................................................................................................................60 APPENDIX A. SPEC SUMMARY TABLE.........................................................................................................................65 APPENDIX B. LICENSING INFORMATION...................................................................................................................66
1. Introduction AirLive Air3GII User’s Manual 1 1 1.Introduction The Air3GII is a high-performance tool that supports wireless networking at home, work, or in a public place. The Air3GII supports a USB 3G modem card, either WCDMA or EVDO and even HSDPA as well, and supports wireless data transfers up to 150M bps, and wired data transfers up to 100 Mbps. The Air3GII is compatible with industry security features.
1. Introduction AirLive Air3GII User’s Manual 2 1.1 Packing List Items Description Contents Quantity 1 Air3GII 1 2 Power adapter 1 3 CD 1
1. Introduction AirLive Air3GII User’s Manual 3 1.2 Hardware Installation A. Hardware configuratio
1. Introduction AirLive Air3GII User’s Manual 4
1. Introduction AirLive Air3GII User’s Manual 5 B. Installation Steps Note: DO NOT connect the router to power before performing the installation steps below. Step 1. Plug a USB modem into USB port. Step 2. Insert RJ45 cable into LAN Port on the back panel of the router. Then plug the other end of into computer. Step 3. Plug the power jack into the receptor on the back panel of the router. Then plug the other end into a wall outlet or power strip.
2.Specification AirLive Air3GII User’s Manual 6 2 2.Specification Getting Started with Easy Setup Utility There are two approaches for you to set up the Air3GII quickly and easily. One is through executing the provided Windows Easy Setup Utility on your PC, and the other is through browsing the device web pages and configuration. 2.1Easy Setup by Windows Utility Step 1： Install the Easy Setup Utility from the provided CD then follow the steps to configure the device. Step 2： Select Language then click “Next” to continue.
2.Specification AirLive Air3GII User’s Manual 7 Step 3： Then click the “Wizard” to continue. Step 4： Click “Next” to continue.
2.Specification AirLive Air3GII User’s Manual 8 Step 5： Select Wireless Enable, and then click “Next” to continue. Step 6： Enter SSID, Channel and Security options, and then click “Next” to continue.
2.Specification AirLive Air3GII User’s Manual 9 Step 7： me select elf” Click” Let WAN service by mysto select WAN service manually. Step 8： Service by Select 3G clicking 3G icon to continue.
2.Specification AirLive Air3GII User’s Manual 10Step 9-1： -Detection” . . Select “Autoand the Utility will try to detect and configure therequired 3G service settings automaticallyClick “Next” to continue Step 9-2： elect ally ed continue. Or you can s“Manual” and manufill in the required 3G service settings providby your ISP. Click “Next” to
2.Specification AirLive Air3GII User’s Manual 11 Step 10: t” to save your Click “Nexsetting. Step 11： is rebooted fect. The Air3GIIto make your entire configuration take ef
2.Specification AirLive Air3GII User’s Manual 12Step 12： to test the Click “Next”Internet connection or you can ignore test. Step 13： to test WAN Click “Next”Networking service. Step 14： pleted. Setup is com
2.Specification AirLive Air3GII User’s Manual 13 .2 Easy Setup by Configuring Web Pages ou can also browse web UI to configure the device. Browse to Activate the Setup Wizard 2Y Type in the IP Address (http://192.168.123.254) Type in the default the password “admin” inSystem Password and then click ‘login’ button. Select your language. Select “Wizard” for basic settings with simple way. Press “Next” to start the Setup Wizard. Configure with the Setup Wizard
2.Specification AirLive Air3GII User’s Manual 14tep 1: Change System system dmin) SPassword. Set up yourpassword. (Default：a Step 2: Select Time Zone. Step 3: Select WAN Auto-Detecting Type. Chooseor Manually to set WAN Type.
2.Specification AirLive Air3GII User’s Manual 15 Step 4: Select Wan ant to use 3G se Type. If you wservice as the main internet access, pleaset the WAN interface as“Wireless WAN” and the WAN type as “3G”. Step 5: 3G Mode. ion Select Auto-Detectthen click “Next” to continue. Step 6: Set up your Wireless Network. Set up your SSID.
2.Specification AirLive Air3GII User’s Manual 16Step 7: Setup your , Encryption Key herethen click”Next” to continue. Step 8: Apply your k Apply Setting. Setting. Then clic Step 9: ish to complete Click Finit.
3.Installation/Un-installation AirLive Air3GII User’s Manual 17 Making Configuration Whenever you want to configure your network or this device, you can access the Configuration Menu by opening the web-browser and typing in the IP Address of the device. The default IP Address is: 192.168.123.254 3 3.Installation/ Un-installation Enter the default password “admin” in the System Password and then click ‘login’ button. Then, you can browse the “Advanced” configuration pages for configuring this device. 3.1 Basic Setting
3.Installation/Un-installation AirLive Air3GII User’s Manual 18 3.1.1 etup 1ddress: The omputers on ur network the LAN IP a Gateway. You can change it if necessary. k: Input your Subnet mask. (All devices in the network must have the ct Ethernet WAN or Wireless WAN to continue. 4. WAN Type: WAN connection type of your ISP. You can click WAN Type combo button to choose a correct one from the following options: . Network S. LAN IP Amust uselocal IP address of this device. The cddress of this device as their Defaultyo2. Subnet Massame subnet mask.) The default subnet mask is 255.255.255.0. 3. WAN Interface: Sele A. 3G
3.Installation/Un-installation AirLive Air3GII User’s Manual 19 orking. The WAN fields may not be necessary for your connection. The ation or service provider for additional information. entered.. 4. 3G Network: Select the 3G Network 5. APN: Enter the APN for your PC card here.(Optional) 6. Pin Code: Enter the Pin Code for your SIM card. (Optional) 7. Dial-Number: This field should not be altered except when required by your service provider. Account: Enter the new User Name for your PC card here, you can contact to your ISP to get it. (Optional) 9. Password: Enter the new Password for your PC card here, you can contact to your ISP to get it. (Optional) 10. Authentication: Choose your authentication. 11. Primary DNS: This feature allows you to assign a Primary DNS Server, contact to your ISP to get it. (Optional) 12. Secondary DNS: This feature allows you to assign a Secondary DNS Server, you can contact to your ISP to get it. (Optional) 13. Connection Control: Select your connection control. There are 3 modes to select: Connect-on-demand: The device will link up with ISP when the clients send outgoing packets. Auto Reconnect (Always-on): The device will link with ISP until the connection is established. Manually: The device will not make the link until someone clicks the connect-button in the Status-page. For 3G WAN Netwinformation on this page will only be used when your service provider requires you to enter a User Name and Password to connect with the 3G network. Please refer to your document1. Dial-Up Profile: Select “Auto-Detection” or “Manual” to continue. If “Auto-Detection” is selected, the device will try to configure some ISP specific dial-up parameters automatically according to the Country, Telecom, and 3G Network information you2. Country: Select your country. 3. Telecom: Select your telecom. 8.
3.Installation/Un-installation AirLive Air3GII User’s Manual 20 11m failure count. The device 4. Keep Alive: This feature must collocate with the function "Auto" of "Auto Connect". Enable it to keep the connection always be established. 5. LCP Echo Request: Enter the time interval and the maximuwill constantly send out the LCP packets for keeping the connection alive. 16. Ping Remote Host: Enter the Remote host IP and the time interval to send the ping packets for keeping the connection alive. B. Static IP Address:
3.Installation/Un-installation AirLive Air3GII User’s Manual 21 ctivate the WWAN connection overed, your y, Primary and Secondary DNS: Enter the proper settings provided by your ISP. s: 1. Activate WWAN for Auto-Failover: With this function enabled, when the Ethernet WAN connection is broken, the device will automatically aand keep you connected to internet with the alternative WWAN broadband service. Meanwhile, if the device detected that the Ethernet WAN connection is recbroadband connection will be switched to use the Ethernet WAN service. 2. WAN IP Address, Subnet Mask, Gatewa C. Dynamic IP Addres 1. Activate WWAN for Auto-Failover: With this function enabled, when the Ethernet WAN connection is broken, the device will automatically activate the WWAN connection and keep you connected to internet with the alternative WWAN broadband service. Meanwhile, if the device detected that the Ethernet WAN connection is recovered, your broadband connection will be switched to use the Ethernet WAN service
3.Installation/Un-installation AirLive Air3GII User’s Manual 22connection is ake the link until someone clicks the connect-button in the Status-page. D. PPP over Ethernet 2. Host Name: Optional, required by some ISPs, for example, @Home. 3. Connection Control: There are 3 modes to select: Connect-on-demand: The device will link up with ISP when the clients send outgoing packets. Auto Reconnect (Always-on): The device will link with ISP until the established. Manually: The device will not m
3.Installation/Un-installation AirLive Air3GII User’s Manual 23 the Ethernet lly activate the WWAN connection and kMean etected that the Ethernet WAN connection is recovered, your broad2. PPPo Password: The account and password your ISP assigned to you. For s ord, leave it blank3. Connection Control: There are 3 modes to select: : The device will link up with ISP when the clients send outgoing packets. Auto Reconnect (Always-on): The device will link with ISP until the connection is established. Manually: The device will not make the link until someone clicks the connect-button in the Status-page. 4. Maximum Idle Time: the amount of time of inactivity before disconnecting your PPPoE session. Set it to zero or enable “Auto-reconnect” to disable this feature. 5. PPPoE Service Name: Optional. Input the service name if your ISP requires it. Otherwise, leave it blank. 6. Maximum Transmission Unit (MTU): Most ISP offers MTU value to users. The default MTU value is 0 (auto). 1. Activate WWAN for Auto-Failover: With this function enabled, when WAN connection is broken, the device will automaticaeep you connected to internet with the alternative WWAN broadband service. while, if the device dband connection will be switched to use the Ethernet WAN service E Account andecurity, this field appears blank. If you don't want to change the passw. Connect-on-demand
3.Installation/Un-installation AirLive Air3GII User’s Manual 24 E. PPTP 1. Activate WWAN for Auto-Failover: With this function enabled, when the Ethernet WAN connection is broken, the device will automatically activate the WWAN connection and keep you connected to internet with the alternative WWAN broadband service. Meanwhile, if the device detected that the Ethernet WAN connection is recovered, your broadband connection will be switched to use the Ethernet WAN service 2. IP Mode: Please check the IP mode your ISP assigned, and select “Static IP Address” or “Dynamic IP Address”. 3. My IP Address and My Subnet Mask: The private IP address and subnet mask your ISP assigned to you.
3.Installation/Un-installation AirLive Air3GII User’s Manual 25 4. Gateway IP and Server IP Address/Name: The IP address of the PPTP server and designated Gateway provided by your ISP. 5. PPTP Account and Password: The account and password your ISP assigned to you. If you don't want to change the password, keep it blank. 6. Connection ID: Optional. Input the connection ID if your ISP requires it. 7. Maximum Idle Time: the time of no activity to disconnect your PPTP session. Set it to zero or enable “Auto-reconnect” to disable this feature. If Auto-reconnect is enabled, this device will connect with ISP automatically after system is restarted or connection is dropped. 8. Connection Control: There are 3 modes to select: Connect-on-demand: The device will link up with ISP when the clients send outgoing packets. Auto Reconnect (Always-on): The device will link with ISP until the connection is established. Manually: The device will not make the link until someone clicks the connect-button in the Status-page. 9. Maximum Transmission Unit (MTU): Most ISP offers MTU value to users. The default MTU value is 0 (auto).
3.Installation/Un-installation AirLive Air3GII User’s Manual 26. L2TP F 1. Activate WWAN for Auto-Failover: With this function enabled, when the Ethernet WAN connection is broken, the device will automatically activate the WWAN connection and keep you connected to internet with the alternative WWAN broadband service. Meanwhile, if the device detected that the Ethernet WAN connection is recovered, your broadband connection will be switched to use the Ethernet WAN service 2. IP Mode: Please check the IP mode your ISP assigned, and select “Static IP Address” or “Dynamic IP Address”. 3. My IP Address and My Subnet Mask: The private IP address and subnet mask your ISP assigned to you. 4. Gateway IP and Server IP Address/Name: The IP address of the L2TP server and designated Gateway provided by your ISP.
3.Installation/Un-installation AirLive Air3GII User’s Manual 27 5. L2TP Account and Password: The account and password your ISP assigned to you. If you don't want to change the password, keep it blank. 6. Connection ID: Optional. Input the connection ID if your ISP requires it. 7. Maximum Idle Time: The time of no activity to disconnect your L2TP session. Set it to zero or enable “Auto-reconnect” to disable this feature. If Auto-reconnect is enabled, this device will connect with ISP automatically, after system is restarted or connection is dropped. 8. Connection Control: There are 3 modes to select: Connect-on-demand: The device will link up with ISP when the clients send outgoing packets. Auto Reconnect (Always-on): The device will link with ISP until the connection is established. Manually: The device will not make the link until someone clicks the connect-button in the Status-page. 9. Maximum Transmission Unit (MTU): Most ISP offers MTU value to users. The default MTU value is 0 (auto). .1.2. DHCP Server 3
3.Installation/Un-installation AirLive Air3GII User’s Manual 28enable the DHCP Server : DHCP lease time to the DHCP client. ed to the clients. Pre5. Prim DNS: Optional. This feature allows you to assign a DNS Serv6. Prim ndary WINS: Optional. This feature allows you to assign a WINS Serv7. Gate uld be the IP address of an alternate Gateway. Click on “Save” to store your settings or click “Undo” to give up the changes. Press “Clients List” and the list of DHCP clients will be shown consequently. 1. DHCP Server: Choose either Disable or Enable. If you function, the following settings will be effective. 2. IP Pool Starting/Ending Address: Whenever there is a request, the DHCP server will automatically allocate an unused IP address from the IP address pool to the requesting computer. You must specify the starting / ending address of the IP address pool. 3. Lease Time4. Domain Name: Optional, this information will be passss “More>>” and you can find more settings ary DNS/Secondaryers ary WINS/Secoers way: Optional. Gateway Address woThis function enables you to assign another gateway to your PC, when DHCP server offers an IP to your PC. Press “Fixed Mapping” and the DHCP Server will reserve the special IP for designated MAC address.
3.Installation/Un-installation AirLive Air3GII User’s Manual 29
3.Installation/Un-installation AirLive Air3GII User’s Manual 30 .1.3. Wireless Settings 3 Wireless settings allow you to set the wireless configuration items. 1. Wireless Module: You can enable or disable wireless function. 2. Network ID (SSID): Network ID is used for identifying the Wireless LAN (WLAN). Client stations can roam freely over this device and other Access Points that have the same Network ID. (The factory default setting is “default”) 3. SSID Broadcast: The router will broadcast beacons that have some information, including SSID so that wireless clients can know how many AP devices by scanning the network. Therefore, if this setting is configured as “Disable”, the wireless clients can not find the device from beacons. 4. Channel: The radio channel number. The permissible channels depend on the Regulatory Domain. The factory default setting is as follow: channel 1~11 for North America. (Channel 1~13 for European (ETSI); channel1~ 14 for Japan). 5. Wireless Mode: Choose “B/G mixed”, “B only”, “G only”, “N only”, “G/N mixed” or “B/G/N mixed”. The factory default setting is “B/G/N mixed”.
3.Installation/Un-installation AirLive Air3GII User’s Manual 31 6. Authentication mode: You may select one of authentication to secure your wireless network: Open Shared, Auto, WPA-PSK, WPA, WPA2-PSK, WPA2, WPA-PSK/WPA2-PSK, or WPA /WPA2. Open Open system authentication simply consists of two communications. The first is an authentication request by the client that contains the station ID (typically the MAC address). This is followed by an authentication response from the AP/router containing a success or failure message. An example of when a failure may occur is if the client's MAC address is explicitly excluded in the AP/router configuration. ations taking part in the se. The shared key is Shared Shared key authentication relies on the fact that both stauthentication process have the same "shared" key or passphramanually set on both the client station and the AP/router. Three types of shared key authentication are available today for home or small office WLAN environments. Auto The AP will Select the Open or Shared by the client’s request automatically. WPA-PSK Select Encryption and Pre-share Key Mode If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits. If you select ASCII, the length of pre-share key is from 8 to 63. Fill in the key, Ex 12345678
3.Installation/Un-installation AirLive Air3GII User’s Manual 32 A. When the WPA function is user must authenticate to this router first to use the Network er IP address or the 802.1X server’s domain-name. PA2 on, the others are same the WPA. for WPA-PSK-TKIP and WPA-PSK2-AES, the others are A-PSK. By pressing “WPS Setup”, you can configure and enable the easy setup feature WPS (Wi-Fi Protection Setup) for your wireless network. WPA Check Box was used to switch the function of the WPenabled, the Wirelessservice. RADIUS ServSelect Encryption and RADIUS Shared Key If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits If you select ASCII, the length of pre-share key is from 8 to 63. Key value shared by the RADIUS server and this router. This key value is consistent with the key value in the RADIUS server. WPA-PSK2 WPA-PSK2 user AES and TKIP for Same the encryption, the others are same the WPA-PSK. WWPA2 add uses AES and TKIP for encryptiWPA-PSK/WPA-PSK2 Another encryption options same the WP WPA/WPA2 Another encryption options for WPA-TKIP and WPA2-AES, the others are same the WPA.
3.Installation/Un-installation AirLive Air3GII User’s Manual 33 1. the wireless clients connected to your wireless network. 2. PIN: You can press Generate New Pin to get an AP PIN. 3. Mode: Select your config Mode from “Registrar” or “Enrollee”. 4. 5. an select the Config Method here from “Pin Code” or “Push 6. g to your setting, the status will show “Start Process” or “No used” PrWPS: You can enable this function by selecting “Enable”. WPS offers a safe and easy way to allowAPConfig Config Status: It shows the status of your configuration. Config Method: You cButton”. WPS status: Accordiness “Wireless Clients List” and the list of wireless clients will be shown consequently.
3.Installation/Un-installation AirLive Air3GII User’s Manual 34 3.1.4. Change Password You can change the System Password here. We strongly recommend you to change the system password for security reason. Click on “Save” to store your settings or click “Undo” to give up the changes.
3.Installation/Un-installation AirLive Air3GII User’s Manual 35 .2 Forwarding Rules 3 3.2.1 Virtual Server This product’s NAT firewall filters out unrecognized packets to protect your Intranet, so all hosts behind this product are invisible to the outside world. If you wish, you can make some of them accessible by enabling the Virtual Server Mapping. A virtual server is defined as a Service Port, and all requests to this port will be redirected to the computer specified by the Server IP. Virtual Server can work with Scheduling Rules, and give user more flexibility on Access control. For the details, please refer to Scheduling Rule.
3.Installation/Un-installation AirLive Air3GII User’s Manual 36 For example, if you have an FTP server (port 21) at 192.168.123.1, a Web server (port 80) at 192.168.123.2, and a VPN server at 192.168.123.6, then you need to specify the following virtual server mapping table:
3.Installation/Un-installation AirLive Air3GII User’s Manual 37 Service Port Server IP Enable21 192.168.123.1 V 80 192.168.123.2 V 1723 192.168.123.6 V Click on “Save” to store your settings or click “Undo” to give up the changes. 3.2.2 Special AP Some applications require multiple connections, like Internet games, Video conferencing, Internet telephony, etc. Because of the firewall function, these applications cannot work with a pure NAT router. The Special Applications feature allows some of these applications to work with this product. If the mechanism of Special Applications fails to make an application work, try setting your computer as the DMZ host instead.
3.Installation/Un-installation AirLive Air3GII User’s Manual 38 1. Trigger: The outbound port number issued by the application. 2. Incoming Ports: When the trigger p the inbound packets sent to the specified port numbers are allowed t the wall. This device provides some predefined settings. Select your application and click “Copy to” to add the predefined settin ur list. Click on “Save” to store your settings or click “Undo” to give up the changes. .2.3 Miscellaneous acket is detected,o pass through fireg to yo 3 1. IP Address of DMZ Host DMZ (Demilitarized Zone) Host is a host without the protection of firewall. It allows a computer to be exposed to unrestricted 2-way communication for Internet games, Video conferencing, Internet telephony and other special applications. 2. UPnP Setting The device supports the UPnP function. If the OS of your client computer supports this function, and you enabled it, like Windows XP, you can see the following icon when the client computer gets IP from the device. Click on “Save” to store your settings or click “Undo” to give up the changes.
3.Installation/Un-installation AirLive Air3GII User’s Manual 39 3.3 Security Setting
3.Installation/Un-installation AirLive Air3GII User’s Manual 403.3.1 Packet Filters Packet Filter includes both outbound filter and inbound filter. And they have same way tosetting. Packet Filter enables you to control what packets are allowed to pass the router. Outbound filter applies on all outbound packets. However, inbound filter applies on packets that destined to Virtual Servers or DMZ host only. You can select one of the two filtering policies: 1. Allow all to pass except those match the specified rules 2. Deny all to pass except those match the specified rules
3.Installation/Un-installation AirLive Air3GII User’s Manual 41 following: tination port For source or destination IP address, you can define a single IP address (4.3.2.1) or a range of IP addresses (4.3.2.1-4.3.2.254). An empty implies all IP addresses. For source or destination port, you can define a single port (80) or a range of ports (1000-1999). Add prefix "T" or "U" to specify TCP or UDP protocol. For example, T80, U53, U2000-2999, No prefix indicates both TCP and UDP are defined. An empty implies all port addresses. Packet Filter can work with Scheduling Rules, and give user more flexibility on Access control. For Detail, please refer to Scheduling Rule. Each rule can be enabled or disabled individually. Click on “Save” to store your settings or click “Undo” to give up the changes. You can specify 8 rules for each direction: inbound or outbound. For each rule, you can define the• Source IP address • Source port • Destination IP address • Des• Protocol: TCP or UDP or both. • Use Rule#
3.Installation/Un-installation AirLive Air3GII User’s Manual 423.3.2 Domain Filters omain Filter prevents users under this device from accessing specific URLs. . Domain Filter: Check if you want to enable Domain Filter. . Log DNS Query: Check if you want to log the action when someone accesses the specific URLs. . Privilege IP Address Range: Setting a group of hosts and privilege these hosts to access network without restriction. Domain Suffix: A suffix of URL can be restricted, for example, ".com", "xxx.com". D1234.
3.Installation/Un-installation AirLive Air3GII User’s Manual 43 someone is accessing the URL met the domain-suffix, what kind of . Check “Drop” to block the access. Check “Log” to log this access. 6. Enable: Check to enable each rule. Click on “Save” to store your settings or click “Undo” to give up the changes. 3.3.3 URL Blocking URL Blocking will block LAN computers to connect with pre-define Websites. The major difference between “Domain filter” and “URL Blocking” is Domain filter require user to input suffix (like .com or .org, etc), while URL Blocking require user to input a keyword only. In other words, Domain filter can block specific website, while URL Blocking can block hundreds of websites by simply a keyword. 5. Action: When action you want
3.Installation/Un-installation AirLive Air3GII User’s Manual 44 the connection will For example, you can use pre-defined word "sex" to block all websites if their URLs to enable each rule. 3.3 MA ent access right for different users and to assign a specific IP address to a certain MAC address. 1. URL Blocking: Check if you want to enable URL Blocking. 2. URL: If any part of the Website's URL matches the pre-defined word, be blocked. contain pre-defined word "sex". 3. Enable: Check Click on “Save” to store your settings or click “Undo” to give up the changes. .4 MAC Control C Address Control allows you to assign differ
3.Installation/Un-installation AirLive Air3GII User’s Manual 45 All of the control: Check "Connection control" to enable the controlling of which nt can't access to the Internet either. Choose "allow" ts, whose MAC addresses are not in the "Control table" (please see below), to connect with this device. which wireless client can associate to the wireless LAN. If a client is denied to associate to LAN, it means the client can't send or receive any data via this device. Click on “Save” to store your settings or click “Undo” to give up the changes. 3.3.5 Miscellaneous 1. MAC Address Control: Check “Enable” to enable the “MAC Address Control”. settings in this page will take effect only when “Enable” is checked. 2. Connection wired and wireless clients can connect with this device. If a client is denied to connect with this device, it means the clieor "deny" to allow or deny the clien3. Association control: Check "Association control" to enable the controlling of the wireless Choose "allow" or "deny" to allow or deny the clients, whose MAC addresses are not in the "Control table", to associate to the wireless LAN.
3.Installation/Un-installation AirLive Air3GII User’s Manual 46any host can connect with this 3. Discard PING from WAN side: When this feature is enabled, any host on the WAN 4. DoS Attack Detection: When this feature is enabled, the router will detect and log the DoS attack comes from the Internet. Currently, the router can detect the following DoS ck, WinNuke, Port Scan, Ping of Death, Land Attack etc. Click on “Save” to store your settings or click “Undo” to give up the changes. 1. Administrator Time-out: The time of no activity to logout automatically, you may set it to zero to disable this feature. 2. Remote Administrator Host/Port In general, only Intranet user can browse the built-in web pages to perform administration task. This feature enables you to perform administration task from remote host. If this feature is enabled, only the specified IP address can perform remote administration. If the specified IP address is 0.0.0.0, product to perform administration task. You can use subnet mask bits "/nn" notation to specified a group of trusted IP addresses for example, "10.1.2.0/24". NOTE: When Remote Administration is enabled, the web server port will be shifted to 80. You can change web server port to other port, too. cannot ping this product. attack: SYN Atta
3.Installation/Un-installation AirLive Air3GII User’s Manual 47 .4 Advanced Setting 3
3.Installation/Un-installation AirLive Air3GII User’s Manual 48 3.4.1 System Log This page support two methods to export system logs to specific destination by means of syslog (UDP) and SMTP(TCP). The items you have to setup including: 1. IP Address for Sys log: Host IP of destination where sys log will be sent to. Check Enable to enable this function. 2. E-mail Alert Enable: Check if you want to enable Email alert (send syslog via email). 3. SMTP Server IP and Port: Input the SMTP server IP and port, which are connected with ':'. If you do not specify port number, the default value is 25. For example, "mail.your_url.com" or "192.168.1.100:26". 4. Send E-mail alert to: The recipients who will receive these logs, you can assign more than 1 recipient, using ';' or ',' to separate these email addresses. 5. E-mail Subject: The subject of email alert, this setting is optional. Click on “Save” to store your settings or click “Undo” to give up the changes.
3.Installation/Un-installation AirLive Air3GII User’s Manual 49 To host your server on a changing IP address, you have to use dynamic domain name service (DDNS). So that anyone wishing to reach your host only needs to know the name of it. Dynamic DNS will map the name of your host to your current IP address, which changes each time you connect your Internet service provider. Before you enable Dynamic DNS, you need to register an account on one of these Dynamic DNS servers that we list in Provider field. 3.4.2 Dynamic DNS tion about your Dynamic DNS Serve .Provider, Host up the changes. To enable Dynamic DNS click the check box next to Enable in the DDNS field. Next you have to enter the appropriate informaName, Username/E-mail, and Password/Key. You can get this information when you register an account on a Dynamic DNS server. Click on “Save” to store your settings or click “Undo” to give
3.Installation/Un-installation AirLive Air3GII User’s Manual 50 3.4.3 QOS Provide different priority to different users or data flows, or guarantee a certain level of performance. . QOS Control: Check Enable to enable this function. 5. QoS Priority: This defines the priority level of the current Policy Configuration. Packets al pplications High or Normal level is recommended. For non-critical applications select a ow level. 6. nable: Check to enable the corresponding QOS rule. 7. ser Rule#: The QoS rule can work with Scheduling Rule number#. Please refer to the ection 3.1.4.7 Schedule Rule. Click on “Save” to store your settings or click “Undo” to give up the changes. 12. Bandwidth of Upstream: Set the limitation of upstream bandwidth 3. Local IP : Ports: Define the Local IP address and ports of packets 4. Remote IP : Ports: Define the Remote IP address and ports of packets associated with this policy will be serviced based upon the priority level set. For criticaLEUS
3.Installation/Un-installation AirLive Air3GII User’s Manual 51 In brief, SNMP, the Simple Network Management Protocol, is a protocol designed to give a user the capability to remotely manage a computer network by polling and setting terminal values and monitoring network events. 3.4.4 SNMP 1. Enable SNMP: You must check “Local”, “Remote” or both to enable SNMP function. If te” is checked, P 3, IP 4: Enter the IP addresses of your SNMP Management PCs. User has “Local” is checked, this device will response request from LAN. If “Remothis device will response request from WAN. 2. Get Community: The community of GetRequest that this device will respond. 3. Set Community: The community of SetRequest that this device will accept. 4. IP 1, IP 2, Ito configure to where this device should send SNMP Trap message. 5. SNMP Version: Select proper SNMP Version that your SNMP Management software supports.
3.Installation/Un-installation AirLive Air3GII User’s Manual 52 dress. The default value is 0.0.0.0, and it means that any internet connected computer can get some information of the device with SNMP protocol. Click on “Save” to store your settings or click “Undo” to give up the changes. 3.4.5 Routing If you have more than one routers and subnets, you will need to enable routing table to allow packets to find proper routing path and allow different subnets to communicate with each other. The routing table allows you to determine which physical interface address to use for outgoing IP data grams. 6. WAN Access IP Address: If you want to limit the remote SNMP access to specific computer, please enter the PC’s IP ad
3.Installation/Un-installation AirLive Air3GII User’s Manual 53 omputing routes throughout the network. Please select RIPv2 only if need this protocol. outing: For static routing, you can specify up to 8 routing rules. You can enter the destination IP address, subnet mask, gateway, and hop for each routing rule, 3.4.6 System Time 1. Dynamic Routing: Routing Information Protocol (RIP) will exchange information about destinations for cyou have different subnet in your network. Otherwise, please select RIPv1 if you2. Static Rand then enable or disable the rule by checking or un-checking the Enable checkbox. Click on “Save” to store your settings or click “Undo” to give up the changes. 1. Time Zone: Select a time zone where this device locates. 2. Auto-Synchronization: Check the “Enable” checkbox to enable this function. Besides, you can select a NTP time server to consult UTC time. 3. Sync with Time Server: Click on the button if you want to set Date and Time by NTP Protocol manually. 4. Sync with my PC: Click on the button if you want to set Date and Time using PC’s Date and Time manually. Click on “Save” to store your settings or click “Undo” to give up the changes. .
3.Installation/Un-installation AirLive Air3GII User’s Manual 54.4.7 Scheduling 3 You can set the schedule time to decide which service will be turned on or off. 1. Schedule: Check to enable the schedule rule settings. New Rule” button. You can as everyday 14:10 to 16:20. 2. Add New Rule: To create a schedule rule, click the “Addedit the Name of Rule, Policy, and set the schedule time (Week day, Start Time, and End Time). The following example configures “ftp time”
3.Installation/Un-installation AirLive Air3GII User’s Manual 55 Click on “Save” to store your settings or click “Undo” to give up the changes.
3.Installation/Un-installation AirLive Air3GII User’s Manual 56 3.5 Tool Box
3.Installation/Un-installation AirLive Air3GII User’s Manual 57 3.5.1 System Info You can view the System Information and System log, and download/clear the System log, in this page.
3.Installation/Un-installation AirLive Air3GII User’s Manual 58.5.2 Firmware Upgrade 3 You can upgrade firmware by clicking “Upgrade” button. 3.5.3 Backup Setting You can backup your settings by clicking the “Backup Setting” function item and save it as a bin file. Once you want to restore these settings, please click Firmware Upgrade button and use the bin file you saved.
3.Installation/Un-installation AirLive Air3GII User’s Manual 59 3.5.4 Reset to Default You can also reset this device to factory default settings by clicking the Reset to default function item. Reboot 3.5.5 You can also reboot this device by clicking the Reboot function item. 3.5.6 Miscellaneous 1. Domain Name or IP address for Ping Test: Allow you to configure an IP, and ping the r settings or click “Undo” to give up the changes. device. You can ping a specific IP to test whether it is alive. Click on “Save” to store you
4.Trobleshooting AirLive Air3GII User’s Manual 60 Troubleshooting 3GII. ou can refer to the following if you are having problems. 1 Why can’t I configure the router even the cable is plugged and the LED is lit? Do a Ping test to make sure that the WiFi Combo Note: It is recommended that you use an Router is responding. Ethernet connection to configure it. 1. Type cmd. 4 4.Troubleshooting This Chapter provides solutions to problems for the installation and operation of the AirY Go to Start > Run. 2. Press OK. orrect IP Address assigned to the Air3GII. It will show four replies if you ping correctly. 3. Type ipconfig to get the IP of default gateway. 4. Type “ping 192.168.123.254”. Assure that you ping the c
4.Trobleshooting AirLive Air3GII User’s Manual 61 Ensure that your Ethernet Adapter is working, and that all network drivers are installed ork adapters. 1. Go to Start > Right click on “My Computer” > Properties. 2. Select the Hardware Tab. that all drivers are installed properly. Look under Device Status to see if the device is working properly. 2 What can I do if my Ethernet connection does not work properly? A. Make sure the RJ45 cable connect with the router. B. Ensure that the setting on your Network Interface Card adapter is “Enabled”. C. If settings are correct, ensure that you are not using a crossover Ethernet cable, not all Network Interface Cards are MDI/MDIX compatible, and use a patch cable is recommended. on still doesn’t work properly, then you can reset it to default. “Manual” mode, and filling in dial-up settings manually. .What can I do if my country and ISP are not in the list? Please choose “Others” item from the list, and filling in dial-up settings manually. properly. Network adapter names will vary depending on your specific adapter. The installation steps listed below are applicable for all netw3. Click Device Manager. 4. Double-click on “Network Adapters”. 5. Right-click on Wireless Card bus Adapter or your specific network adapter. 6. Select Properties to ensure 7.8. Click “OK”. 9. D. If the connecti 3 Problems with 3G connection? A.What can I do if the 3G connection is failed by Auto detection? Maybe the device can’t recognize your ISP automatically. Please selectB
4.Trobleshooting AirLive Air3GII User’s Manual 62 C.What can I do if my 3G connection is failed even the dongle is plugged? Please check the following items: g sure the PIN code to see all dial-up settings are correct l from your ISP is available in your environment gnize my 3G data card even it is plugged? he rted. mary DNS, and NS? he device will show this information after you choose country and Telcom. You p dropping? middle level. ss connection? wireless connection. I. Make sure you have inserted a validated SIM card in the 3G data card, and the subscription from ISP is still available II. If you activate PIN code check feature in SIM card, makinyou fill in dial-up page is correct III. Checking with your ISPIV. Make sure 3G signaD. What can I do if my router can’t reco There might be compatibility issue with some certain 3G cards. Please check tlatest compatibility list to see if your 3G card is already suppoE. What should I insert in APN, PIN Code, Account, Password, PriSecondary D Tcan also check these values with your ISP. F. Which 3G network should I select? It depends on what service your ISP provide. Please check your ISP to know this information. G. Why my 3G connection is kee Please check 3G signal strength from your ISP in your environment is above 4 Something wrong with the wireleA. Can’t setup a wireless connection? I. Ensure that the SSID and the encryption settings are exactly the same to the Clients. II. Move the Air3GII and the wireless client into the same room, and then test the
4.Trobleshooting AirLive Air3GII User’s Manual 63 III. Disable all security settings such as WEP, and MAC Address Control. nt again. icating normally. If no, make sure that the AC power mask, gateway and DNS settings are evice, home security systems or ceiling fans, dramatically. Keep e such as I. rong AP: Ensure that the client is connected with the correct icon in the taskbar. Networks in Wireless Configure. Ensure Air3GII to default setting pping? ntenna orientations for the Air3GII. way from the wall or other objects. Air3GII, and your Access Point and Wireless product away from electrical devices that generate RF noise, like IV. Turn off the Air3GII and the client, then restart it and then turn on the clieV. Ensure that the LEDs are indand Ethernet cables are firmly connected. VI. Ensure that the IP Address, subnetcorrectly entered for the network. VII. If you are using other wireless dlights in your home, your wireless connection may degrade your product away from electrical devices that generate RF noismicrowaves, monitors, electric motors… B. What can I do if my wireless client can not access the Internet? Out of range: Put the router closer to your client. II. Wrong SSID or Encryption Key: Check the SSID or Encryption setting. III. Connect with wAccess Point. i. Right-click on the Local Area Connection ii. Select View Available Wirelessyou have selected the correct available network. iii. Reset theC. Why does my wireless connection keep droI. Antenna Orientation. i. Try different aii. Try to keep the antenna at least 6 inches aII. Try changing the channel on the adapter to a different channel to avoid interference. III. Keep yourmicrowaves, monitors, electric motors, etc.
4.Trobleshooting AirLive Air3GII User’s Manual 64 5 2. 6 Ho2. Find 3. 4. ry default settings. What to do if I forgot my encryption key? 1. Go back to advanced setting to set up your Encryption key again. Reset the Air3GII to default setting w to reset to default? 1. Ensure the Air3GII is powered on the Reset button on the right side Press the Reset button for 8 seconds and then release. After the Air3GII reboots, it has back to the facto
Appendix A. Spec Summary Table AirLive Air3GII User’s Manual 65 Appendix A. Spec Summary Table 3G Access USB port Standards IEEE 802.11b/g IEEE 802.3 E 802.3u IEEWireless Standard IEEE 802.11 B\G\N Data Rate 11G: 54, 48, 36, 24, 18, 12, 9, and 611N: Max physical rate up to 300Mb11B: 11, 5.5, 2, 1 Mbps Mbps ps Frequency 2.4-2.4835GHz or 2.412-2.462GHz Range Coverage Indoors approx. 30-50 meters; Outdoors up to 80-100 meters # of Channels 1-11 for N. America (FCC);1-11 for Canada (DOC) 1-13 Europe (Except Spain and France) (ETSI) 1-14 Japan (TELEC); 1-11 for Taiwan (NCC)Security 64-bit and 128-bit WEP Encryption; WPA encryption Antenna External 2or2.35dBi Antenna. Firewall IP Filtering NAT (Network Address Translation) with VPN Pass through MAC Filtering Supported WAN type 3G,Static IP, Dynamic IP, PPPoE,PPTP,L2TP Connection Scheme Connect-on-demand, Auto-Disconnect NAT function Class C ;One-to-Many; Max 253 Users; Virtual Server; DMZ Host VPN PPTP, L2TP and IPSec Pass Through Config.& Management Web-Based IE, Navigator browser and SNMP IP assignment DHCP Server and Client Working Environment Temperature: 0~40oC, Humidity 10%~90% non-condensing OS supported Windows 95/98/ME/NT/2000/XP; Linux Power Full range(100-240V), Switching 5V 1.2A
Appendix B. Licensing information AirLive Air3GII User’s Manual 66is product includes copyrighted third-party software licensed under the terms of the GNU eneral se. Ple o the GNU General Public License below to check the detailed licens The following parts of this p ject to the GNU GPL, and those software packages are copy eir respeLinux-2.4.28 system kernel busybox_1_00_rc2 bridge-utilsdhcpcdISC DHCP V2 P5 util-lin fdiske2fsprogs 1.27 minsamsyslogd spread from buwirelentpclient of NTP client iRT61a .1X apvsftpd-quota-tGNU Wget Availability of source code Please vis Appendix B. Licensing information hTG Public Licenisase refer t terms of th e. roduct are subctive authors. right by th 0.9.5 -1.3 ux 2.12b for application i-lpd ba 2.2.7a sybox ss tools mplementation pd for 802 plication 2.0.3 ools 3.13 it our web site or contact us to obtain more information.
Appendix B. Licensing information AirLive Air3GII User’s Manual 67 Version 2, June 1991 Prea The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and e the software is free for all its users. This General Pub ree Software Foundation's software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your prog Whe ferring to freedom, not price. Our General Public Lice ou have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things. ed to make restrictions that forbid anyone to deny you these rights o certain responsibilities for For example, if you distribute copies of such a for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software. Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations. GNU GENERAL PUBLIC LICENSE Copyright (C) 1989, 1991 Free Software Foundation, Inc. 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. mble change free software--to make sures to most of the Flic License applirams, too. n we speak of free software, we are re that ynses are designed to make sure To protect your rights, we neor to ask you to surrender the rights. These restrictions translate tou if you distribute copies of the software, or if you modify it. y program, whether gratis or
Appendix B. Licensing information AirLive Air3GII User’s Manual 68 Finally, any free program is threaten atents. We wish to avoid the anger that redistributors of a free program will individually obtain patent licenses, in effect making the progra y patent must be licensed for eveThe precise term w. GNU GENERAL PUBLIC LICENSE g the Program or a portion of it, either verbatim or with modifications and/or anslated into another language. (Hereinafter, translation is included without limitation in the if its contents constitute a work based on the Program ndependent of having been made by running the Program). Whether that is true depends on 's source code as you receive it, any medium, provided that you conspicuously and appropriately publish on each copy an ou may charge a fee for the physical act of transferring a copy, and you may at your option . You may modify your copy or copies of the Program or any portion of it, thus forming a work ased on the Program, and copy and distribute such modifications or work under the terms of from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License. ed constantly by software pdm proprietary. To prevent this, we have made it clear that anryone's free use or not licensed at all. s and conditions for copying, distribution and modification follo TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The "Program", below, refers to any such program or work, and a "work based on the Program" means either the Program or any derivative work under copyright law: that is to say, a work containintrterm "modification".) Each licensee is addressed as "you". Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only (iwhat the Program does. 1. You may copy and distribute verbatim copies of the Programinappropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. Yoffer warranty protection in exchange for a fee. 2bSection 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived
Appendix B. Licensing information AirLive Air3GII User’s Manual 69 ) If the modified program normally reads commands interactively when run, you must cause er how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an print an announcement.) These requirements apply to tifiable sections of that work re not derived from the Program, and can be reasonably considered independent and sepa ions hen you distribute them as separate works. But when you distribute the same sections as the Program with the Program (or ith a work based on the Program) on a volume of a storage or distribution medium does not complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily um customarily used for software interchange; ed as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you cit, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the usannouncement, your work based on the Program is not required to the modified work as a whole. If idenarate works in themselves, then this License, and its terms, do not apply to those sectwpart of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program. In addition, mere aggregation of another work not based onwbring the other work under the scope of this License. 3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following: a) Accompany it with theused for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medior, c) Accompany it with the information you receivreceived the program in object code or executable form with such an offer, in accord with Subsection b above.)
Appendix B. Licensing information AirLive Air3GII User’s Manual 70 distribution of executable or object code is made by offering access to copy from a y, modify, sublicense or distribute remain in full compliance. Program or its derivative works. These and all its terms and conditions for copying, distributing or modifying the ram (or any work based on the Program), the recipient e of a court judgment or allegation of patent infringement or for any other and any other pertinent obligations, then as a consequence you ay not distribute the Program at all. For example, if a patent license would not permit yalty-free redistribution of the Program by all those who receive copies directly or indirectly rough you, then the only way you could satisfy both it and this License would be to refrain ntirely from distribution of the Program. The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. Ifdesignated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copthe Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties 5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so,Program or works based on it. 6. Each time you redistribute the Progautomatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License. 7. If, as a consequencreason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License mrothe
Appendix B. Licensing information AirLive Air3GII User’s Manual 71 istributed through that system in reliance on consistent application of that system; it is up to lear what is believed to be a consequence of the st of this License. dy of this License. applies to it and "any later version", you have the option of llowing the terms and conditions either of that version or of any later version published by the r to ask for permission. For software which is N WRITING THE COPYRIGHT HOLDERS AND/OR THER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, ITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED ARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software dthe author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly cre 8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the bo 9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Program specifies a version number of this License which foFree Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation. 10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the authocopyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IOEW
Appendix B. Licensing information AirLive Air3GII User’s Manual 72E PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF INCIDENTAL OR CONSEQUENTIAL DAMAGES RISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT U OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO PERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THALL NECESSARY SERVICING, REPAIR OR CORRECTION. 12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, ANOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOOHAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. END OF TERMS AND CONDITIONS
第十二條 型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

Navigation menu