Option OGI0401 HSPA USB Stick User Manual Globetrotter module GTM378

Option NV HSPA USB Stick Globetrotter module GTM378

Contents

Quick Start Guide

Option Quick Start Guide GI0401 OPTION NV, Gaston Geenslaan 14, B-3001 Leuven Tel +32 16 317 411 Fax +32 16 207 164 http://www.option.com Option Confidential
GI0401 Quick Start Guide Author: J. NAbout this document Overview and Purpose This document describes how to use the hardware, software and gives some installation instructions. Confidentiality All data and information contained or disclosed by this document is confidential and proprietary of Option NV, and all rights therein are expressly reserved. By accepting this document, the recipient agrees that this information is held in confidence and in trust and will not be used, copied, reproduced in whole or in part, nor its contents revealed in any manner to others without prior and written permission of Option NV. Version History Date Version Author(s) Revision(s) Remarks May 13, 2008 V01 J. Nys Initial version Table of contents 1 Driver installation ................................................................................................................................. 2 2 Communicating with the GI0401.......................................................................................................... 4 3 Led functionality................................................................................................................................... 6 ys Version: V01 –D1Creation Date: May 13, 2008 Page: 1 of 6 Option Confidential: This document is Option Confidential - it may not be duplicated, neither distributed externally without prior and written permission of Option NV.
GI0401 Quick Start Guide Author: J. N1 DRIVER INSTALLATION Following drivers are available for WinXP, Win2K and Win XP x64 edition:  Multifunction Adapter : Globetrotter GI40X  Network : Globetrotter Network Card  Ports : Globetrotter Application Port  Ports : Globetrotter Diagnostics Port  Multi function adaptors : Globetrotter GI40X - Mass storage Installation procedure: 1. If you have not already done so, install and connect the cradle. The unit shall be connected correctly only if the "Welcome to the Found New Hardware Wizard" appears. 2. By connecting the unit to the PC, Windows will detect new hardware and will ask to install the drivers. Insert the CD and install the drivers following the windows driver installation wizard. As there are multiple drivers the "Found new hardware" wizards needs to run multiple times. Further installation instructions will be given for Windows XP. 3. For Windows XP: on the first dialog ("connect to Windows Update ?") select No, not this time: Figure 1: Hardware wizard 4. On the next dialog, select "Install software automatically": ys Version: V01 –D1Creation Date: May 13, 2008 Page: 2 of 6 Option Confidential: This document is Option Confidential - it may not be duplicated, neither distributed externally without prior and written permission of Option NV.
GI0401 Quick Start Guide Author: J. N Figure 2: automatic search for driver If Windows does not automatically find the correct driver, you should select Install from a list or specific location and browse to the folder "DriverXP_2000" on the CD 5. For the driver signing warning, click "Continue Anyway": Figure 3: Not signed driver warning 6. In total, five or six devices will be detected: • Globetrotter Bus • Globetrotter Mass storage • Globetrotter Network Card • Globetrotter Application Interface • Globetrotter Diagnostics Interface Repeat steps 3 through 5 for the 3 remaining devices to complete the installation. On successful installation of the drivers, all devices should show up in the device manager: ys Version: V01 –D1Creation Date: May 13, 2008 Page: 3 of 6 Option Confidential: This document is Option Confidential - it may not be duplicated, neither distributed externally without prior and written permission of Option NV.
GI0401 Quick Start Guide Author: J. N 2 COMMUNICATING WITH THE GI0401 This section describes briefly how to setup HyperTerminal to enter AT commands. Note: A SIM card needs to be entered in the device to make a network connection. 1. Go to device manager, and check which port is the Application port. ys Version: V01 –D1Creation Date: May 13, 2008 Page: 4 of 6 Option Confidential: This document is Option Confidential - it may not be duplicated, neither distributed externally without prior and written permission of Option NV. Figure 4: Device manager 2. Open HyperTerminal Therefore you can follow the following path: Start → Programs → accessories → Communication → HyperTerminal 3. Enter a name for your HyperTerminal Connection and press OK. 4. In the next window, change the connecting using field to the Application Port. Click on OK.
GI0401 Quick Start Guide Author: J. N Figure 5: Connection port 5. Now the next window will appear. Modify the Bit per second field to 115200 and Click the OK button. Now HyperTerminal is configured. You are now ready to communicate with the GI0401. ys Version: V01 –D1Creation Date: May 13, 2008 Page: 5 of 6 Option Confidential: This document is Option Confidential - it may not be duplicated, neither distributed externally without prior and written permission of Option NV.
GI0401 Quick Start Guide Author: J. N3 LED FUNCTIONALITY The LEDs on the GI0401 provide information on the connection status of the device. ys Version: V01 –D1Creation Date: May 13, 2008 Page: 6 of 6 Option Confidential: This document is Option Confidential - it may not be duplicated, neither distributed externally without prior and written permission of Option NV.

Navigation menu