On Track Innovations OTI-SAT6700 Ultra-compact, multi-purpose NFC reader User Manual UNO Specifications

On Track Innovations Ltd Ultra-compact, multi-purpose NFC reader UNO Specifications

User manual

Confidential & Proprietary Version 1.9 UNO Specifications Version 1.9 Notice This manual contains intellectual property including, but not limited to, trade secrets and know-how, operation procedures and production procedures that belong solely to oti. Disclosure, use, and/or production of any part of the above are strictly forbidden, except under a written license from oti.
Uno Specifications Version 1.9 FCC Compliance Confidential & Proprietary Page 1 FCC Compliance This device (Saturn 6700) complies with Part 15, of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15, subpart C of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. Changes or modifications in this equipment, not expressly approved by the party responsible for compliance (On Track Innovations Ltd,) could void the user’s authority to operate the equipment. FCC ID: JNX-OTI-SAT6700 Responsible Party: On Track Innovations LTD.. Z.H.R Industrial Zone. Rosh Pina 12000 ISRAEL Phone: +972-4-6868000 Email: Supportoti@otiglobal.com
Uno Specifications Version 1.9 Table of Contents Confidential & Proprietary Page 2 Table of Contents FCC COMPLIANCE ...................................................................................................................................... 1 TABLE OF CONTENTS ................................................................................................................................ 2 TABLE OF FIGURES .................................................................................................................................... 3 VERSIONS TABLE ........................................................................................................................................ 4 1 INTRODUCTION .................................................................................................................................. 5 1.1 CERTIFIED AND SUPPORTED APPLICATIONS...................................................................................... 6 1.2 SUPPORTED STANDARDS .................................................................................................................. 7 2 BASIC CONTACTLESS OPERATION .............................................................................................. 8 3 TECHNICAL SPECIFICATIONS ....................................................................................................... 9 3.1 PRODUCT FEATURES ......................................................................................................................... 9 3.2 PRODUCT TECHNICAL SPECIFICATIONS .......................................................................................... 10 4 READER MODELS ............................................................................................................................. 12 4.1 RS232 MODEL ................................................................................................................................ 12 4.2 USB MODEL ................................................................................................................................... 12 4.3 INTERFACE CABLES ......................................................................................................................... 13 4.3.1 RS232 cable ............................................................................................................................... 13 4.3.2 USB Cable ................................................................................................................................. 14 5 DIMENSIONS ...................................................................................................................................... 15 5.1 FRONT VIEW ................................................................................................................................... 15 5.2 SIDE VIEW ...................................................................................................................................... 16 6 UNO MOUNTING................................................................................................................................ 17 6.1 ON PANEL MOUNTING .................................................................................................................... 18 6.2 FLUSH MOUNTING .......................................................................................................................... 20 6.3 COUNTERTOP (DESKTOP) MOUNTING ............................................................................................. 25 7 CONTACT US ...................................................................................................................................... 26
Uno Specifications Version 1.9 Table of Figures Confidential & Proprietary Page 3 Table of Figures Figure ‎2-1: Card Presentation ............................................................................................................ 8 Figure ‎5-1: Front View ..................................................................................................................... 15 Figure ‎5-2: Side View ...................................................................................................................... 16 Figure ‎5-3: UNO Size Scale ....................................................................................................... 16 Figure ‎6-1: Flush and On Panel Mounting ............................................................................ 17 Figure ‎6-2: UNO Mounting Studs .................................................................................................... 18 Figure ‎6-3: UNO Panel Mounting view ................................................................................... 19 Figure ‎6-4: UNO Panel Mounting Drilling Template ...................................................................... 19 Figure ‎6-5: UNO Flush Mounting – Front View .................................................................... 20 Figure ‎6-6: UNO Flush Mounting – Side View ............................................................................... 21 Figure ‎6-7: UNO Flush Mounting – Front View .................................................................... 21 Figure ‎6-8: UNO Flush Mounting – Side View ...................................................................... 22 Figure ‎6-9: UNO Flush Mounting – Angular View ............................................................... 23 Figure ‎6-10: UNO Flush Mounting – Rear View ................................................................... 24 Figure ‎6-11: Uno Flash Mounting - Cutout...................................................................................... 24 Figure ‎6-12: UNO Countertop (Desktop) Mounting – Front View ................................... 25
Uno Specifications Version 1.9 Versions Table Confidential & Proprietary Page 4 Versions Table Version Description Date Name 1.1 First version 2014-11-02 Moshe Cohen 1.2  Supporting operation voltage of 8 - 45VDC instead of 2 - 15 VDC  Adding a note regarding "Behind Panel" mounting  Having only one thickness configuration (17mm thickness) instead of 17 or 25 mm 2014-11-10 Moshe Cohen 1.3  Reader structural update  New connectors  Updates about the mounting options 2014-11-30 Moshe Cohen 1.4  New pinout for the full interface connector  New pictures of the UNO prototype  Update contact information of the oti America support team 2015-01-13 Moshe Cohen 1.5  New warning regarding power supply stability  New warning regarding mounting on metal  Replacing "flat" wording by "flush" 2015-07-14 Aharon Binur 1.51 Decrease the input voltage range to 40Vdc 2015-09-29 Aharon Binur 1.6 Add Recommended Cutout and Drilling for installation 2015-12-03 Aharon Binur 1.7 Adding notes to FCC compliance statement. 2016-04-14 Avner 1.8 Update total power sonsumption and IP rating 2016-05-10 Hemy 1.9 Add clear distinction between USB and RS232 models. 2016-05-16 Hemy
Uno Specifications Version 1.9 Introduction Confidential & Proprietary Page 5 1 Introduction The UNO is an ultra-compact, certified payment NFC Reader based on oti’s field proven technology which is specifically designed for payment and mass transit applications. Its compact design enables easy integration and installation in unattended self-service payment stations, such as ATMs, AVMs, TVMs, gaming and gambling machines, kiosks, access control gates and more. The UNO uses oti’s patented matched antenna technology. The UNO supports SAM house that allows the reader to access its own or external security elements such as Mifare Authentication SAM. The UNO is designed to be seated on any counter as an attended reader or alternatively can be installed as part of an unattended vending or service machine. UNO’s plug-and-play design makes it easy to connect to any existing infrastructure and POS terminal, quickly upgrading it to contactless operations without disrupting ongoing business operations. In its USB configuration, the UNO is USB powered, this option contributes to the easy installation and maintenance of the reader.
Uno Specifications Version 1.9 Introduction Confidential & Proprietary Page 6 1.1 Certified and Supported Applications The UNO is certified and supports the following contactless applications:  EMV o Contactless EMV L1  VISA o VISA PayWave MSD o VISA PayWave qVSDC o NDOT over VISA for transportation o VISA Global Transit Payment Pilot Specification o VISA Pilot Visa PayWave Ticketing Extension Specification o VISA Asia Pacific WAVE 2  MasterCard o MasterCard PayPass M/Chip (including Data Exchange) o MasterCard PayPass Mag Stripe o NDOT over MasterCard for transportation  American Express o AMEX ExpressPay  Discover o Discover ZipNetwork  Interac o Interac Flash  SoftCard o SoftCard (ISIS) SmartTap  Mifare o Mifare Ultralight o Mifare Classic o Mifare DESFire (optional)  Transparent (Pass-Through) Communication o ISO/IEC 14443 Type A - Transparent Proximity o ISO/IEC 14443 Type B - Transparent Proximity o ISO/IEC 15693 Vicinity (optional) - Transparent Vicinity  Other o Additional proprietary applications *In process of certification
Uno Specifications Version 1.9 Introduction Confidential & Proprietary Page 7 1.2 Supported Standards The UNO is compatible with the following standards:  FCC  CE  UL  RoHS compliance  ISO 9001: 2008  ISO/IEC 14443 Proximity Type A&B  ISO/IEC 15693 Vicinity  Mifare  MasterCard TQM label  IPX5
Uno Specifications Version 1.9 Basic Contactless Operation Confidential & Proprietary Page 8 2 Basic Contactless Operation When a valid contactless payment card is presented to the reader, the reader performs a payment transaction with the contactless card. If the transaction is accepted, the unit will display a row of 4 LEDs that light up in sequence and the reader buzzer will inform the user about the transaction verdict. The reader then communicates the transaction data to the Host (POS). A landing zone logo, lighted by the reader, on the graphic overlay indicates where the contactless card or tag should be presented. The interactive LEDs and Buzzer give the user an indication of the transaction status. Figure ‎2-1: Card Presentation
Uno Specifications Version 1.9 Technical Specifications Confidential & Proprietary Page 9 3 Technical Specifications 3.1 Product Features General  Flexible, software configurable, certified intelligent reader solution  oti advanced Host – Reader TLV based protocol  Contactless transparent communication support  Modular design by Hardware and Software  Tamper-proof remote software update  Available as OEM RF Interface  Bi-directional RF interface between Reader and Contactless Smart Cards  Carrier frequency: 13.56 MHz  ISO/IEC 14443 Type A/B and Mifare full support  Optional I-Code and ISO/IEC 15693 support Communication Links  USB 2.0 – full speed, CDC, mini USB connector  RS 232, 8 data bits, no parity, 1 stop bit, full 8-bit binary data. Client defined baud rate Connectors: Either a JST 10 pin ZPD interface, located in the back of the reader and contains a Power, RS232, USB and External buzzer lines. Or a mini USB connector located at the back of the reader and supports USB only. In this configuration the reader is 5VDC USB powered. User Interface  4 LED indicators  Buzzer Electronic Board Power Requirements  8VDC - 40VDC (Onboard Switch Mode Power Supply) or 5VDC via USB connector. Max power consumption  Less than 3W (RF signal on) with 8-40VDC supply.  Less than 2.5W (RF signal on) with 5VDC supply from USB bus. SAM Interface  One micro SIM Slot Security  High security encryption system (3DES/AES/RSA) protects the reader’s operating system  Vandalism-proof PKI protected software update mechanism  DUKPT (Derived Unique Key Per Transaction) support  Offline PIN Authentication support  Secure boot loader (firmware update) protocol Environmental Conditions  Operating: -20° to 70°C (-4° to 158°F)
Uno Specifications Version 1.9 Technical Specifications Confidential & Proprietary Page 10 3.2 Product Technical Specifications The performance/electrical specifications for each feature of the UNO reader are given in the table below. Table ‎3-1: Performance/Electrical Specifications Feature Specification  RF Interface: RF Carrier Frequency 13.56 MHz RF Output 450mW ISO/IEC 14443 A&B and Mifare Full compliance ISO/IEC 15693 Vicinity Optional  Micro SIM push-push Interface  Communication Links: USB, RS232  USB: 2.0 Full speed CDC  Connectors Standard mini-USB connector USB only Mini USB connector Full interface JST 10 pin P/N BM10B-ZPDSS  Indicators: LEDs Four programmable on-board LEDs Buzzer Multi tone differential drive buzzer  Electronic Board Power Requirements: 8VDC – 40VDC, Pmax<3W On-board switching power supply 5VDC, Pmax<2.5W From USB bus in USB only  Mechanical: Dimensions (See Figure ‎5-1: Front View and Figure ‎5-2: Side View) H – 0.66” (17mm) W – 2.40” (61mm) D – 3.07” (78mm) Weight 125 gr. Vibrations 10  200 Hz @ 2.0G IP rating IPX5  Temperature: Operating -20°C to 70°C (-4°F to 158°F)
Uno Specifications Version 1.9 Technical Specifications Confidential & Proprietary Page 11 Warning: Power supply minimum requirements Keeping the DC supply voltage within the specified allowed range is crucial to guarantee proper operation of the equipment. The use of AC rectified power supply source, which is not properly filtered, forms a risk of too low voltage dips and hence should be avoided. It is highly recommended to check this issue with proper tools (e.g. oscilloscope) during the reader installation. For more details contact oti technical team via oti’s sales representatives.
Uno Specifications Version 1.9 Reader models Confidential & Proprietary Page 12 4 Reader models 4.1 RS232 model The RS232 interface is implemented using a JST 10 pin connector (JST P/N BM10B-ZPDSS). The connector exposes 10 lines according to the following: 1. RS223 Rx 2. RS232 Tx 3. USB D- 4. Buzser 1 5. USB D+ 6. Buzzer 2 7. GND (direct) 8. Vin 9. 5V 10. GND Ext (via common mode chock) Note: the 10 pin connector optionaly support USB communication and extranl buzzer activation. This option is not in OTI standard products portfolio. 4.2 USB model A mini-USB connector on the back of the reader provides communication to the host terminal (POS). It can be used to provide either USB or RS232 serial interface depending on the reader’s hardware configuration. DC power to the unit can be provided either through the mini-USB connector or through the power jack which is part of the communication cable.
Uno Specifications Version 1.9 Reader models Confidential & Proprietary Page 13 4.3 Interface cables 4.3.1 RS232 cable A JST 10 pin connector (JST P/N BM10B-ZPDSS) is available to access the reader full interface. Figure ‎4-1: BM10B-ZPDSS Connector – Top Entry Type Figure ‎4-2: BM10B-ZPDSS Connector – Side Entry Type Figure ‎4-3: BM10B-ZPDSS Connector housing
Uno Specifications Version 1.9 Reader models Confidential & Proprietary Page 14 4.3.2 USB Cable The USB cable (1.8m) has a mini-USB upstream connector on the reader side and a USB downstream connector on the host side. This cable can be in use while the reader is in USB only configuration. In this hardware configuration, the reader is USB powered, no additional power supply is required. Figure ‎4-4: USB Cable Figure ‎4-5: USB Connection 123VCCD-D+GNDSaturn Mini USB Upstream Connector234GNDD+D-Host USB Downstream ConnectorUSB Cable15VCC
Uno Specifications Version 1.9 Dimensions Confidential & Proprietary Page 15 5 Dimensions The reader’s front and side view dimensions are given in this chapter. 5.1 Front View The reader’s front view is illustrated in the figure below. Figure ‎5-1: Front View
Uno Specifications Version 1.9 Dimensions Confidential & Proprietary Page 16 5.2 Side View The reader’s side view dimensions are illustrated in the figure below. Figure ‎5-2: Side View Figure ‎5-3: UNO Size Scale
Uno Specifications Version 1.9 UNO Mounting Confidential & Proprietary Page 17 6 UNO Mounting While the UNO can be placed simply on the counter as a countertop reader connected to a terminal, the UNO can also be mounted as part of an unattended machine. This chapter specifies the mounting options and procedures. The UNO mounting possibilities include 3 main options, as illustrated below: 1. On panel mounting 2. Flush mounting 3. Countertop (Desktop) mounting The different mounting configuration allows to install the UNO on top of the machine surface, leveled with the machine surface or over the counter. Figure ‎6-1: Flush and On Panel Mounting Warning: Mounting on metal Direct mounting of the reader on metallic/conductive panel requires special attention as it negatively affects the reader contactless performance. For more details contact oti technical team via oti’s sales representatives.
Uno Specifications Version 1.9 UNO Mounting Confidential & Proprietary Page 18 6.1 On Panel Mounting The image below illustrates the UNO’s on panel mounting option. Figure ‎6-2: UNO Mounting Studs 1. The UNO is equipped with 4 mounting studs for front panel mounting. 2. The studs and cable are inserted through holes in the front panel. The nuts are fastened over the studs from the back of the front panel, protecting against potential attempts to dismantle the unit from the front.
Uno Specifications Version 1.9 UNO Mounting Confidential & Proprietary Page 19 3. Figure ‎6-3: UNO Panel Mounting view Figure ‎6-4: UNO Panel Mounting Drilling Template
Uno Specifications Version 1.9 UNO Mounting Confidential & Proprietary Page 20 6.2 Flush Mounting The image below illustrates the UNO’s flush mounting option. Figure ‎6-5: UNO Flush Mounting – Front View
Uno Specifications Version 1.9 UNO Mounting Confidential & Proprietary Page 21 Figure ‎6-6: UNO Flush Mounting – Side View 1. The UNO can be mounted flush with the front panel surface. 2. The flush mounting option requires a 63x80 mm cutout in the center of the non-metallic section of the front panel. 3. A mounting holder (green) in the back of the reader is tighten the device to the panel. A gasket that is separated between the device cover and the panel keep it waterproof. Figure ‎6-7: UNO Flush Mounting – Front View
Uno Specifications Version 1.9 UNO Mounting Confidential & Proprietary Page 22 Figure ‎6-8: UNO Flush Mounting – Side View
Uno Specifications Version 1.9 UNO Mounting Confidential & Proprietary Page 23 Figure ‎6-9: UNO Flush Mounting – Angular View
Uno Specifications Version 1.9 UNO Mounting Confidential & Proprietary Page 24 Figure ‎6-10: UNO Flush Mounting – Rear View Figure ‎6-11: Uno Flash Mounting - Cutout
Uno Specifications Version 1.9 UNO Mounting Confidential & Proprietary Page 25 6.3 Countertop (Desktop) mounting As the product software supports both attended and unattended usage profiles, the UNO can be used also as attended reader. In order to use the UNO in its countertop configuration you should connect it to the POS using the full interface to via the USB interface and to place it over the counter or alternatively in its cradle (if available). Figure ‎6-12: UNO Countertop (Desktop) Mounting – Front View
Uno Specifications Version 1.9 Contact Us Confidential & Proprietary Page 26 7 Contact Us For oti America Technical Support (US and Canada):  Phone: +1-732-429-1900 9:00 am to 5:00 pm Eastern time Monday – Friday  Email: support@otiamerica.com For oti Technical Support (International):  Phone: +972-4-6868000 (Ext. 8090)  Email: info@otiglobal.com

Navigation menu