Omron Okayama factory WD30B DeviceNet Wireless Unit User Manual WD30SE ai

Omron Corporation Okayama factory DeviceNet Wireless Unit WD30SE ai

Contents

User Manual 2 of 3

621580 3516748515959.5Unit: mm664.5 dia74113.335.8 dia.39Cable length: 20002094115Allows clearance of 62 mm or longerbetween the antennas.Antenna cable length is 2 m.Radius of 38or longerRadius of 38or greaterHole diameterof 11 mm orlongerConnector10.5 diaDo not bend morethan 40 mm.Model WD30-SE/SE01DeviceNet Wireless SlaveInstruction SheetENGThank you for purchasing an OMRON product.Please find you have the product of your interest and read this User's Guide thoroughly for better understanding before using this product.Please keep this User's Guide at hand for quick reference after having read it through.The description on DeviceNet Wireless Master (Model WD30-ME/ME01) is provided on the front side.Model WD30-SE Model WD30-SE01OMRON CorporationAll Rights ReservedPlease read the following manual, as well, for safe and appropriate use.• DeviceNet Wireless Unit User's Manual(No. M071-E1-01)IC NOTICEThis device has been designed to operate with an antenna having a maximum gain of 2.14 dB. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The Required antenna impedance is 50 ohms.To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication.This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.FCC WARNINGChanges or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:· Reorient or relocate the receiving antenna.· Increase the separation between the equipment and receiver.· Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.· Consult the dealer or an experienced radio/TV technician for help.This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.Wireless standards have been met for the following countries. The product cannot be used in any other countries.Australia, Austria, Belgium, Canada, China (see note), Cyprus, Czech, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Japan, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Singapore, Slovakia, Slovenia, Spain, Sweden, Switzerland, UK, USANote: Channel 51 cannot be used in China. Use channels 2 to 34 or channels 52 to 83. Use is also prohibited in aircraft or near airports.CautionTo ensure that the WLAN transmitter complies with current FCC regulations limiting both maximum RF output power and human exposure to radio frequency radiation, a separation distance of at least 20 cm must be maintained between the unit's antenna and the body of the user and any nearby persons at all times and in all applications and uses.Precautions for Safe UsePlease observe the following for your safety.(1) Do not use the device for real-time control (I/O control that requires the same high-speed response as DeviceNet).(2) Do not apply excessive vibration or shock, or drop the device accidentally.(3) Do not use the device subject to:• corrosive or flammable gas • excessive debris and dust• water, oil, and chemicals• drastic change in temperature that causes condensation• static electricity and extreme noise (4) Do not route the communication cable parallel or close to high-voltage or strong-current cables.(5) Do not plug or unplug the connector while the power is supplied to the communication cable.(6) Use the communication cable specified in this User's Guide.(7) Do not allow accidental entry of debris while the cover is open.(8) Do not mount the device to a location where excessive external force might be applied or that might be used as a footing.(9) Fasten the screws with the torque specified in this User's Guide.(10) Do not use this device in the vicinity of any device that might malfunction due to the presence of radio waves from this device.Precautions for Correct Use(1) Disassembly and modification of this unit are prohibited by Radio Law and may be subject to a penalty.(2) Do not take off the certification label of technical conformity.(3) Make sure to turn off the device before cabling.(4) Use a two-sided adhesive tape or a string to temporarily secure the device for mounting adjustment and avoid the damage caused by dropping.(5) Do not use the device in a location that is subject to direct sunlight and extremely high humidity or close to a TV set, a radio, a motor or drill that emits sparks, a strong magnet, and a fluorescent light.(6) Do not bend or break the antenna. Do not wind an electrical wire around the antenna.(7) Mount the device so as not to make the antenna parallel to an electrical wire or a metal plate. Mount the device as far from an electrical wire or a metal plate as possible.(8) Communication performance depends on the environment. This device may be interfered by other wireless units that send radio waves in the same frequency band as this device. Make sure to perform the tests, such as the mounting test, provided by this device in advance.Suitability for UseOMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of the products in the customer's application or use of the product.Take all necessary steps to determine the suitability of the product for the systems, machines, and equipment with which it will be used.Know and observe all prohibitions of use applicable to this product.NEVER USE THE PRODUCTS FOR AN APPLICATION IN-VOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DE-SIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.• This User's Guide provides information required for using DeviceNet Wireless Unit. Please read this User's Guide and "DeviceNet Operation Manual" for better understanding and appropriate use before using this device. Also, please keep this User's Guide at hand for quick reference.SpecificationsGeneral specificationsDeviceNet communications power supply voltage Rated voltage 24 VDC Allowable voltage range 11 to 25 VDC (provided from the DeviceNet network power supply)Power consumption 4 W Ambient operating temperature -10 to +50˚C Ambient operating humidity 25 to 85%Ambient storage temperature -20 to +65˚C Weight Approx. 200 gCablingDeviceNet communications cableUse the DeviceNet exclusive cable with a single socket(Model DCA1-5CN@@F1).AntennaUse the supplied two antennas.Make sure to attach both antennas. With a singleantenna only, the diversity effect is not available.Radio waveformCommunications methodFrequency bandNumber of channelsAntenna powerWireless interval data transfer speedWireless interval protocolTransmission formatExpected transmission distance Number of connectable Wireless SlavesWireless interface specificationsSpectrum diffusion (direct diffusion: DS-SS)Simplex (half-duplex)2.4-GHz band (2402.2 to 2480.2 MHz)66 channels (using frequency division)10 mW/MHz 100 kbps1: N polling selecting methodHDLC compliantIndoors: 50 m (The transmission distance depends on the environment.)The transmission distance can be extended using relays. (3 stages max.) 64 unitsPackage ContentsWireless unit ·················································································1 Instruction Sheet ··········································································3 Screw (with nut) ···········································································2Declaration of Conformity······························································1 Notification Sheet ··········································································1Pencil-type antenna ······································································2Magnet-base antenna ··································································2(ME)(ME01)DeviceNet interface specificationsCommunications functionsMaster/Slave Connection Remote I/O functionsExplicit messaging functionsMountingMounting requirementFasten the screws with torque of up to 0.3 N·m (2.7 in·lb).External terminal/connectorAntenna connectorSMA connectorTwo antennas are supplied.Communications connectorDeviceNet communications connector (plug),DeviceNet micro-connector compliantDimensions MountingUse the screw to mount the two locations shown in the figure below. * You can mount SE01 main unit inside by attaching the magnet-base antennas outside.WD30-SE01 supplied antenna<WD30-AT001 (magnet-base antenna)>Available model: WD30-SE/SE01 Unavailable model: WD30-SComponent names and functionsThis LED displays the self-node address (NNODE) in RUN mode. When errors are detected, this LED displays the error code and the error node of the errors in the order of error detections. In TEST mode, this LED displays the received wave level.7-segment LEDUse this switch to set up the communications speed and the status of the DeviceNet interface.Set the switch before power-on. Only the switch setting immediately after power-on is effective. Any changes to the switch setting after power-on will be ignored.DeviceNet setup switch [SW1]MS (Module Status) : Main unit status NS (Network Status) : DeviceNet network statusWS (Wireless Status): Wireless network statusStatus LEDStatus LED7-segment LEDNNODEswitchDeviceNet setupswitchMode selectionswitchPush buttonWNODEswitchWCHswitchWirelesssetup switchNo. Description1 Communications (MODE1)2speed selection (MODE2)3Relay-exclusive/non-exclusive4Maintain/clear the output at communications error detectionDeviceNet communications speed setupCommunicationsspeed (bps)State of the dip switch12MODE1 MODE2Remarks125k OFF OFF Trunk length distance of 500 m250k ON OFF Trunk length distance of 250 m500k OFF ON Trunk length distance of 100 m−ON ON Setup prohibited, no communicationsNo. Description ON OFF34Relay-exclusive/non-exclusive Exclusive Non-exclusiveMaintain/clear the output atcommunications error detection Maintain ClearUse this switch to set up operation mode of Wireless Slave. (3 positions)Mode selection switchOperation mode SW statusRun mode RUNTest mode TESTSetup mode SETPush this button to trigger individual settings in SET mode.Push button [SW2]Use this switch to set up the node address (NNODE) of the DeviceNet interface. Set the switch before power-on. Only the switch setting immediately after power-on is effective. Any changes to the switch setting after power-on will be ignored.NNODE switchSet the wireless interface node address. The setting range is from "01" to "64".Set the switch before power-on. Only the switch setting immediately after power-on is effective. Any changes to the switch setting after power-on will be ignored.WNODE switchUse this switch to set up the group address of the wireless interface and the communications channel. Set a decimal number from "02" to "34", "51" to "83". Channel 51 cannot be used in China. Use channels 2 to 34 or channels 52 to 83.Setting any out-of-range number in RUN mode will cause a switch setup error. Set the switch before power-on. Only the switch setting immediately after power-on is effective. Any changes to the switch setting after power-on will be ignored.WCH switchUse this switch to set up parameters for TEST and SET modes.Set the switch before power-on. Only the switch setting immediately after power-on is effective. Any changes to the switch setting after power-on will be ignored.Wireless setup switch [SW3]No. Description ON OFF1(Always OFF) −−2(Always OFF) −−3Wireless channel monitoring NoYes4Mounting test NoYes5(Always OFF) −−6DeviceNet Slave registration NoYes7(Always OFF) −−8Default configuration NoYes10.5Always use a Class 2 power supply to conform to UL standards.Use a DC power line less than 3 m to conform to EN standards. If a power line of 3 m or longer is required, extend the length at the Switching Power Supply's primary side (i.e., the AC power line).Conformity to Safety Standards Dansk [Danish]Deutsch [German]Eesti [Estonian]EnglishEspañol [Spanish]Français [French]Italiano [Italian]Latviski [Latvian]Nederlands [Dutch]Malti [Maltese]Magyar [Hungarian]Polski [Polish]Português [Portuguese]Slovensko [Slovenian]Slovensky [Slovak]Suomi [Finnish]Svenska [Swedish]Íslenska [Icelandic]Norsk [Norwegian]Undertegnede Omron Corporation erklærer herved, at følgende udstyr WD30 overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.Hiermit erklärt Omron Corporation, dass sich das Gerät WD30 in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.Käesolevaga kinnitab Omron Corporation seadme WD30 vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.Hereby, Omron Corporation, declares that this WD30 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.Por medio de la presente Omron Corporation declara que el WD30 cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.Par la présente Omron Corporation déclare que l’appareil WD30 est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.Con la presente Omron Corporation dichiara che questo WD30 è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.Šiuo Omron Corporation deklaruoja, kad šis WD30 atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.Hierbij verklaart Omron Corporation dat het toestel WD30 in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.Alulírott, Omron Corporation nyilatkozom, hogy a WD30 megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.Omron Corporation declara que este WD30 está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.Omron Corporation vakuuttaa täten että WD30 tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.Härmed intygar Omron Corporation att denna WD30 står l överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. Hér með lýsir Omron Corporation yfir því að WD30 er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.Omron Corporation erklærer herved at utstyret WD30 er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Omron Corporation ∆ΗΛΩΝΕΙ ΟΤΙ WD30 ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/EK.Cesky [Czech]Omron Corporation tímto prohlašuje, ze tento WD30 je ve shode se základními pozadavky a dalšími príslušnými ustanoveními smernice 1999/5/ES.Ελληνικη [Greek]Lietuviu [Lithuanian]Hawnhekk, Omron Corporation, jiddikjara li dan WD30 jikkonforma mal-htigijiet essenzjali u ma provvedimenti ohrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.Omron Corporation izjavlja, da je ta WD30 v skladu z bistvenimi zahtevami in ostalimi relevantnimi dolocili direktive 1999/5/ES.Omron Corporation týmto vyhlasuje, ze WD30 splna základné poziadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.Niniejszym Omron Corporation oswiadcza, ze WD30 jest zgodny z zasadniczymi wymogami oraz pozostalymi stosownymi postanowieniami Dyrektywy 1999/5/EC.Ar šo Omron Corporation deklare, ka WD30 atbilst Direkt vas 1999/5/EK butiskajam pras bam un citiem ar to saist tajiem noteikumiem.

Navigation menu