Omnilink Systems OL300G GSM/GPS Ankle Worn Tracking Device User Manual

Omnilink Systems, Inc. GSM/GPS Ankle Worn Tracking Device Users Manual

Users Manual

Omnilink User Guide 1 12-18-08 v2.0 Omnilink Orion Hardware User Guide for OL300-G, OL300-C and OL300-B
Omnilink User Guide 2 12-18-08 v2.0 Omnilink Orion - ComponentsStrap Retaining BracketDevice Device Inside Device Hinges Device Outside Response Button Locking Column StrapBack Plate Back Plate Inside Locking Posts Back Plate Outside Hinge Gaps Strap Retaining Pins Charger Extension and Charging Head Wall Plug Wall Plug Adapters Pins Top Pin Bottom Pin North America Australia EMEA United Kingdom
Omnilink User Guide 3 12-18-08 v2.0 The device should be stored with the strap and back plate positioned as if the device were placed on an offender. The strap needs to remain in a circular position so it stays soft and pliable. Store the device with only the top pin inserted. When possible, the device should be plugged into an electrical outlet to ensure that it has been charged for at least 3 hours prior to use. Users should prepare the device and populate FocalPoint with the necessary information prior to attaching the device. There are two key tasks to complete as part of the pre-installation process: 1. Assign a rate plan (i.e., frequency with which the device is located) 2. Assign a bracelet to an offender in FocalPoint. TASK ONE: ASSIGN A RATE PLAN Step 1: Hover over the “Administration” link. Step 2: Click “Manage Devices” to launch the “Device ID” screen. Omnilink Orion – Storing the UnitOmnilink Orion – Pre-InstallationStep 1: Hover over the Administration link. Step 2: Click Manage Devices.
Omnilink User Guide 4 12-18-08 v2.0 Step 3: Click the desired device when the “Device ID” screen launches. Step 4: Click the “Rate Plan” button on the “Edit Device” screen to launch the “Rate” screen. Step 3: Click on the desired device. Step 4: Click on the Rate Plan button.
Omnilink User Guide 5 12-18-08 v2.0 Step 5: Click the check box of the desired rate plan. Note: Only the rate plans available to you will appear on the Rate screen. Step 6: Click the “Apply Changes” button to refresh the screen. Step 7: Ensure that “Program has been assigned to the device” appears below the Apply Changes button. TASK TWO: ASSIGN A BRACELET TO AN OFFENDER IN FOCALPOINT. (See Setting up an Offender in the FocalPoint software guide). Step 5: Click the check box for the desired rate plan. Step 6: Click the Apply Changes button to save the change.
Omnilink User Guide 6 12-18-08 v2.0 Step 3: Hold the back plate against the ankle, place one of the sets of strap holes over the locking posts and wrap the strap around the ankle Step 4: Place the locking posts in different sizing holes as necessary for the locking harness to reach the retaining pins. Step 2: Remove the top pin from the device. Remove the device and back plate from the strap. Set the device aside. Step 1: Charge the Device for 3 hours prior to installation. Unplug the charger from the wall outlet and remove the charger cord from the device. Omnilink Orion – Installation
Omnilink User Guide 7 12-18-08 v2.0 Step 5: Slide the locking harness onto the retaining pins. Step 6: Place the device hinges into the hinge gaps and roll the device closed until the device is flush with the back plate. Step 7: Insert the top pin until it is flush with the device. Step 8: Insert the bottom pin until it connects with the top pin and sits flush with the device.
Omnilink User Guide 8 12-18-08 v2.0 Step 9: Ensure that the device is securely attached to the ankle and that the Omnilink decals point up.
Omnilink User Guide 9 12-18-08 v2.0 Once the device is attached, Users must log into FocalPoint and clear the “device tamper” alerts, as well as wait to ensure that FocalPoint is successfully tracking the device. Step 1: Log into FocalPoint. Step 2: On the home page, look for any “Device Tamper” icons for the device. Step 3: Click the “Device Tamper” icon. The tamper details window will open. Omnilink Orion – Finalizing Setup in FocalPoint
Omnilink User Guide 10 12-18-08 v2.0 Step 4: Click the “Clear Alert” button on the “Alert Details” screen. Step 5: Before releasing the offender, wait until two location points are received to verify that FocalPoint is successfully tracking the device and that NO device tamper alert has returned to the screen. If a tamper alert appears, exchange the pins.
Omnilink User Guide 11 12-18-08 v2.0 Omnilink Orion – Removing the DeviceOmnilink Orion – Charging the DeviceStep 1: Direct offender to place the heel of the shoe on the edge of the table. Step 2: Using a flat-head screwdriver, turn the bottom pin ¼ turn until the top pin snaps and pops out of the device. Remove the top pin and device. Step 1: Plug the wall adapter into an outlet and attach the charger head to the device. Tip: Magnets in the charger head and device ensure placement of the charging contacts.
Omnilink User Guide 12 12-18-08 v2.0 TECHNICAL SUPPORT (800) 297-0128 (678) 624-5919 techsupport@Omnilinksystems.com FULFILLMENT (678) 624-5944 fulfillment@Omnilinksystems.com Warning: Changes or modifications to this device not expressly approved by Omnilink Systems could void the user’s authority to operate the equipment. FCC Notices: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two Conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference recievec, including interference that may cause undesired operation. Omnilink Orion – Contacting Omnilink Omnilink Orion – Notifications
Omnilink User Guide 13 12-18-08 v2.0 CE Statement: Hereby, Omnilink Systems declares that the Omnilink Orion OL300-G is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. CE Labeling Requirements: The ‘CE’ marking must be affixed to a visible location on the OEM product. The CE mark shall consist of the initials “CE” taking the following form: • If the CE marking is reduced or enlarged, the proportions given in the above graduated drawings must be respected. • The CE marking must have a height of at least 5mm except where this is not possible on account of the nature of the apparatus. • The CE marking must be affixed visibly, legibly, and indelibly.

Navigation menu