Olympus Medical Systems EC-1 Low Power Transmitter User Manual GT1629 FCC MAJ 1467 C1
Olympus Medical Systems Corp. Low Power Transmitter GT1629 FCC MAJ 1467 C1
Contents
- 1. Users manual Part 1
- 2. Users manual Part 2
- 3. Users manual Part 3
- 4. Users manual Part 4
- 5. Users manual part 5
Users manual Part 4
![160Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEMTable 6.1Enlarging imagesYou can enlarge the image data displayed in the image display area of the main screen.1. Click the [Zoom] button (see Figure 6.24). The image being displayed in the image display area will be enlarged.Figure 6.24• When you enlarge an image, the [Zoom] button is changed to the original size mode (see Figure 6.25). Click the [Zoom] button again to restore the image to its original size.Figure 6.25• Magnification varies in the image view mode (see Table 6.2).Overlap One image is refreshed.Sequential All images displayed are refreshed.Zoom buttonEnlargement mode Original size mode](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-1.png)
![Chapter 6 Capsule Endoscope Image Observation161OLYMPUS CAPSULE ENDOSCOPE SYSTEMTable 6.2Structure enhancementUse the [Enhance] buttons to emphasize the patterns on the surface of the mucosa (see Figure 6.26).Figure 6.26Image view mode Magnification1 Display mode x 22 Display mode x 1.54 Display mode − (not available)Enhance buttons](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-2.png)
![162Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEMThe structure enhancement level can be switched between “Normal” and “High” (see Table 6.3).Table 6.3Antenna displayThe antenna display identifies the antenna with the best signal reception.The antenna information is for reference only. Do not depend on this information to determine the position of the capsule endoscope.1. Click the [Antenna] button in the antenna display section (see Figure 6.27). The antenna display panel is displayed.Figure 6.27Click the [Antenna] button again to hide the antenna display panel.Enhancement level DetailNormal The image is displayed without structure enhancement applied.High The image is displayed with structure enhancement applied.Antenna button](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-3.png)
![Chapter 6 Capsule Endoscope Image Observation163OLYMPUS CAPSULE ENDOSCOPE SYSTEMCreating thumbnailsClicking the [Capture] button while the playback of image data is paused will create and display thumbnails of the image data in the thumbnail view area (see Figure 6.28).To create thumbnails, double click on the image display area.Figure 6.28When you click the [Capture] button during the playback of image data, a thumbnail will be created for the image being displayed at that moment, and the playback of image data will be paused.Removing thumbnails1. On the thumbnail view area, select the thumbnail you wish to remove.2. Right-click on the selected thumbnail to display the context menu (see Figure 6.29).Figure 6.29Capture buttonThumbnail view area](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-4.png)
![164Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEM3. Select “Remove” from the context menu to delete the selected thumbnail.• You can also press the “Delete” key on the keyboard to delete the selected thumbnail.• If the thumbnail included in the reporting group is removed, one of the below messages is displayed.−The selected thumbnails are added to a report. If you delete these thumbnails, they will be removed from a report.−If you delete the selected thumbnails, the comments added to the group which contains these thumbnails will be deleted.• If no thumbnail has been created, pressing the land mark will create a new thumbnail.Setting featuresYou can set a featured region on the time bar to identify the range of images (small bowel area) to focus on.1. Click and select a thumbnail to set a feature.2. Click the [Landmarks] button on the thumbnail and select “Landmarks” from the context menu (see Figure 6.30).Figure 6.30Landmarks button](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-5.png)
![Chapter 6 Capsule Endoscope Image Observation165OLYMPUS CAPSULE ENDOSCOPE SYSTEM3. The feature setting screen is displayed (see Figure 6.31).Figure 6.31Table 6.44. Select “No marker”, “Starting point of marker”, or “End point of marker” to set the marker area. Also set the origin for the relative time.• Only one thumbnail can be used as the starting point of marker, and as the end point of marker.• To set the selected thumbnail as origin of a relative time scale, check the checkbox for “Relative time”.No marker No marker is set for the images.Starting point of markerSets the selected thumbnail as the first image of the marker area.End point of markerSets the selected thumbnail as the last image of the marker area.Origin for relative timeSets the selected thumbnail as the origin of a relative time scale.](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-6.png)
![166Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEM5. Click the [OK] button. The feature interval is now set.• If you right-click on the thumbnail, the context menu which contains the items in the Table 6.4 appears.You can set features by selecting one of the context menu.• Click [Cancel] to discard the settings and exit the feature setting screen.• The configured feature interval is shown in a different color on the time bar.• When only the “Start of feature interval” is specified, the last image of the data set becomes the “End of feature interval”.• When only the “End of feature interval” is specified, the first image of the data set becomes the “Start of feature interval”.Time barThe time bar indicates the position of the currently displayed image relative to the overall timeframe (see Figure 6.32).Figure 6.32The thumbnails are connected with a line to a position on the time bar that corresponds to the time at which they were captured.• When you drag the indicator on the time bar to the left or the right, the image data being displayed in the image area is updated accordingly.• The time bar becomes interrupted when the recorder unit is turned OFF or when signals are not being received.Time bar](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-7.png)
![Chapter 6 Capsule Endoscope Image Observation167OLYMPUS CAPSULE ENDOSCOPE SYSTEM• When you click on the time bar, the indicator moves to the clicked position, and the image area is updated to display the corresponding image.Red color detection barFigure 6.33The red line on the red color detection bar indicates the position of red-color detected image data.](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-8.png)
![168Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEM6.4 Generating reportsPreparing to generate a reportReport preparation screenFigure 6.341. Group display areaDisplays images as groups.2. Make group buttonGroups images.3. Change sequence buttonDisplays the group edit screen for changing the group ordering.4. Next buttonDisplays the report generation screen.5. Back buttonReturns to the main screen.6. Thumbnail view areaDisplays thumbnails to be selected as members of a group.7. Image display areaDisplays thumbnails selected in the thumbnail view area or the group display area.8. Comment areaAllows attaching comments to a group.2. Make group button3. Change sequence button4. Next button5. Back button6. Thumbnail view area 7. Image display area8. Comment area9. User dictionary1. Group display area](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-9.png)
![Chapter 6 Capsule Endoscope Image Observation169OLYMPUS CAPSULE ENDOSCOPE SYSTEM9. User dictionaryUsed when entering comments. As you type into the comment area, terms starting with the characters you have entered will be searched for and displayed.Grouping imagesOnly the images that have been assigned to a group can be included in a report. You can associate a comment to each group.1. Click the [Report] button on the main screen (see Figure 6.35). The report preparation screen is displayed.Figure 6.352. From the thumbnail view area, check the checkbox under the thumbnail you wish to include in the reporting group (see Figure 6.36).Figure 6.36Report buttonThumbnail view area](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-10.png)
![170Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEMTo select multiple images, check the checkboxes under the thumbnails (see Figure 6.37).Figure 6.373. Click the [Make group] button (see Figure 6.38). Selected images are displayed in the group display area and a group is created.Figure 6.38Images that are already grouped will be greyed out in the thumbnail view area.CheckboxMake group button](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-11.png)
![Chapter 6 Capsule Endoscope Image Observation171OLYMPUS CAPSULE ENDOSCOPE SYSTEMAdding images to an existing groupTo add images to an existing group, drag and drop the thumbnails from the thumbnail view area onto the destination group.1. In the thumbnail view area, select the thumbnails you wish to add to the group.To select multiple images, check the checkboxes under the thumbnails.2. Drag the selected thumbnails onto the destination group (see Figure 6.39). The selected images are added to the group.Figure 6.39Removing images from an existing groupTo remove unwanted images from a group, drag and drop the thumbnails from the group onto the thumbnail view area.1. In the group display area, select the thumbnails you wish to remove from the group.To select multiple images, check the checkboxes under the thumbnails.2. Drag the selected thumbnails onto the thumbnail view area. The selected images are removed from the group.In the thumbnail view area, ungrouped images will no longer be greyed out.](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-12.png)
![172Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEMMoving images from one group to anotherTo move images from one group to another, drag and drop the thumbnails between the groups.1. In the thumbnail view area, select the thumbnails you wish to transfer.• To select multiple images, check the checkboxes under the thumbnails.• You cannot select thumbnails from multiple groups.2. Drag the selected thumbnails onto the destination group (see Figure 6.40). The selected images are transferred.Figure 6.40](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-13.png)
![Chapter 6 Capsule Endoscope Image Observation173OLYMPUS CAPSULE ENDOSCOPE SYSTEMDrawing ovals on observation imagesYou can draw ovals on images to indicate areas of interest.1. Click the [Oval] button on the image display area (see Figure 6.41).Figure 6.41The image display area displays the image for the thumbnail selected in the thumbnail view area or the group display area.2. Click & drag on the image in the image display area to draw an oval (see Figure 6.42).Figure 6.42• The oval will be centered around the point where the mouse was clicked.• Release the mouse button to complete the oval.Oval button](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-14.png)
![174Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEM• An oval that extends beyond the limits of the image display area will not be shown.3. To undo the oval(s) you have drawn, click the [Undo] button.To delete an oval, select the oval and press the [Delete] key on the keyboard.Drawing arrows on observation imagesYou can draw arrows on images to point out areas of interest.1. Click the [Arrow] button on the image display area (see Figure 6.43).Figure 6.43The image display area displays the image for the thumbnail selected in the thumbnail view area or the group display area.Arrow button](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-15.png)
![Chapter 6 Capsule Endoscope Image Observation175OLYMPUS CAPSULE ENDOSCOPE SYSTEM2. Click and drag on the image in the image display area to draw an arrow (see Figure 6.44).Figure 6.44• The arrow will be drawn from the point where the mouse was clicked.• Release the mouse button to complete the arrow.• An arrow that extends beyond the limits of the image display area will not be shown.3. To undo the arrow(s) you have drawn, click the [Undo] button.To delete an arrow, select the arrow and press the [Delete] key on the keyboard.Entering commentsA comment can be attached to each group. Input your comment using the keyboard or the user dictionary.1. On the report preparation screen, type in your comment into the comment area.2. Words that start with the entered character string are displayed in the candidate display area.• A candidate is displayed when a character is entered following a space.](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-16.png)
![176Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEM• As you type into the comment area, terms starting with the characters you have entered will be searched for and displayed in the user dictionary area. To enter a term from the dictionary, select the term and press the [Enter] key on the keyboard.3. Use the up/down arrow keys on the keyboard to select the word you wish to enter from the candidate display area.4. Press the [Enter] key on the keyboard to enter the currently selected word into the comment entry box.• You can also click on a word in the candidate display area to enter it into the comment box.• To change the language when entering comments, right-click on the comment area and select the language.Editing the user dictionaryWords that are frequently used in reports can be registered in the user dictionary.1. Click the [Edit] button on the report preparation screen. The user dictionary edit screen is displayed.2. To add a word or phrase to the user dictionary, type the text into the text box on the user dictionary edit screen, and click the [Add] button.3. To remove a word or phrase from the user dictionary, select a registered word or phrase from the user dictionary, and click the [Remove] button.Figure 6.45](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-17.png)
![Chapter 6 Capsule Endoscope Image Observation177OLYMPUS CAPSULE ENDOSCOPE SYSTEMSorting groups1. Click the [Change sequence] button on the report preparation screen (see Figure 6.46). The group edit screen is displayed.Figure 6.462. Select the group you wish to reorder.3. Drag and drop the selected group to achieve the desired ordering of groups (see Figure 6.47). The groups are rearranged.Figure 6.474. Click the [OK] button. The change is applied, and the report preparation screen will be displayed. Click the [Cancel] button to discard the changes and return to the report preparation screen.Change sequence button](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-18.png)
![178Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEMGenerating reportsReport generation screenFigure 6.487. “Display antenna” checkbox8. Individual information checkbox9. Age checkbox10. “Signature” checkbox1. Summary entry box2. Findings/procedure entry box3. Reason for referral entry 4. Referring physician entry box5. Examination information display area6. Patient data display area11. “Facility logo” checkbox](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-19.png)
![Chapter 6 Capsule Endoscope Image Observation179OLYMPUS CAPSULE ENDOSCOPE SYSTEM1. Summary entry boxUsed to enter a summary.2. Findings/procedure entry boxUsed to enter findings and procedures.3. Reason for referral entry boxUsed to enter reasons for referral.4. Referring physician entry boxUse to enter the name of the referring physician.5. Examination information display areaDisplays examination information that has already been set.6. Patient data display areaDisplays patient data that has already been entered.7. “Display antenna” checkboxCheck to display antenna information on the report.8. Individual information checkboxCheck to generate a report that does not contain information about the individual.To remove individual information (such as a facial portrait) from the image data, you will need to set the hiding feature. For more information, refer to “Hiding images” on page 216.9. Age checkboxCheck to generate a report that does not include the patient’s age.10. “Signature” checkboxCheck to generate a report with a signature block.11. “Facility logo” checkboxCheck to display a facility logo on a report.](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-20.png)
![180Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEMDisplaying the report generation screen1. Click the [Next] button on the report preparation screen (see Figure 6.49). The report generation screen is displayed.Figure 6.492. Contents specified on the initial setup screen are displayed (see Figure 6.50).Figure 6.50Only grouped images are displayed.3. Images grouped on the report preparation screen are displayed by group.Next button](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-21.png)
![Chapter 6 Capsule Endoscope Image Observation181OLYMPUS CAPSULE ENDOSCOPE SYSTEMDisplaying print previewsYou can preview how the report will appear when printed.1. Click the [Preview] button on the report generation screen (see Figure 6.51). The print preview of the report is displayed.Figure 6.51Preview button](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-22.png)
![182Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEMPrint preview screenFigure 6.529. Magnification11. Print button7. Last Page button6. Next Page button3. First Page button5. Page number1. Back button2. Print preview area4. Previous Page button8. Zoom out button10. Zoom in button](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-23.png)
![Chapter 6 Capsule Endoscope Image Observation183OLYMPUS CAPSULE ENDOSCOPE SYSTEM1. Back buttonReturns to the report generation screen.2. Print preview areaDisplays the print preview.3. First Page buttonDisplays the print preview for the first page.4. Previous Page buttonDisplays the print preview for the previous page.5. Page numberShows the page number for the displayed page.6. Next Page buttonDisplays the print preview for the next page.7. Last Page buttonDisplays the print preview for the last page.8. Zoom out buttonZooms out the print preview.9. MagnificationShows the magnification used to display the print preview.10. Zoom in buttonZooms in the print preview.11. Print buttonDisplays the print setup screen.](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-24.png)
![184Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEMPrinting reports1. Click the [Print] button on the report generation screen (see Figure 6.53) or the print preview screen. The print setup screen is displayed.Figure 6.53You can also display the print setup screen by clicking the [Print] button on the print preview screen.2. Click the [Print] button on the print setup screen (see Figure 6.54). The report is printed.Figure 6.54• By default, the reports are adjusted to print to letter size paper.• You can select the paper size from letter the size or A4.• When A4 size is selected, the print size will be automatically scaled to match the paper size.Print buttonPrint button](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-25.png)
![Chapter 6 Capsule Endoscope Image Observation185OLYMPUS CAPSULE ENDOSCOPE SYSTEMExporting reportsYou can export the generated report in HTML format.1. Click the [Export] button on the report generation screen (see Figure 6.55). The destination setting screen is displayed.Figure 6.552. Select the destination (see Figure 6.56).Figure 6.56• When exporting a report from the workstation, you can only export to external drives.• When exporting a report from the Endo Capsule software light version of the PC, you can export to any drive.Export button](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-26.png)
![186Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEM3. Click the [OK] button (see Figure 6.57). The report is exported to the selected destination.Figure 6.57• The report is exported in HTML format.• The exported report can be viewed by any HTML browser.Saving reportsYou can save the generated report. The report can also be saved as a draft.1. Click the [Save] button on the report generation screen (see Figure 6.58). The save screen is displayed.Figure 6.58OK buttonSave button](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-27.png)
![Chapter 6 Capsule Endoscope Image Observation187OLYMPUS CAPSULE ENDOSCOPE SYSTEM2. To finalize the report, click the [Finalize] button (see Figure 6.57). A report file is generated in HTML format.Figure 6.59• To save the report as a draft, click the [Save draft] button (see Figure 6.58). When the report is finalized, an HTML file of the report is created and the report history is recorded. When the report is saved as a draft, an HTML file of the report is not created and the report history is not recorded.Figure 6.60• Save the thumbnail data frequently to prevent possible data loss due to a breakdown.• You can also save the thumbnail data by selecting “Save thumbnail” from the “File” menu. In this case, an HTML file of the report is not created and the report history is not recorded.Finalize the report before you write the report onto the DVD.FinalizeSave draft button](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-28.png)
![188Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEMViewing the report historyYou can view past reports by selecting them from the report history.1. Select “History” from the “Tools” menu on the report generation screen when you open the examination data in the drive other than DVD. The history screen is displayed.Figure 6.61Select ”History“ from the ”Tools“ menu on the main screen when you open the examination data in the DVD (see Figure 6.61). The history screen is displayed.2. From the report history, select the report you wish to view, and click the [Open] button (see Figure 6.62).Figure 6.62ToolsOpen button](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-29.png)
![Chapter 6 Capsule Endoscope Image Observation189OLYMPUS CAPSULE ENDOSCOPE SYSTEM3. The selected report is displayed on the report preview screen.Click the [Cancel] button on the history screen to exit the history screen.](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-30.png)
![190Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEM6.5 Examination data managementWhile writing to or reading from a USB memory, do not remove the USB device from the port. It may damage examination data and/or the USB device.• The “Examination Data Management” function is not available in Endo Capsule Software Light.• Remove the USB devices from the workstation and restart the workstation when it does not work properly. Then connect the removed USB devices again.• The report file is exported to the following location.(∗) Words in parentheses vary according to the exported data.](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-31.png)
![Chapter 6 Capsule Endoscope Image Observation191OLYMPUS CAPSULE ENDOSCOPE SYSTEMExamination list screenFigure 6.631. Examination listDisplays the list of examination data stored on the selected drive.2. Drive selection boxSelect the drive on which the examination data you wish to view is stored.3. Back buttonReturns to the main screen.4. Open buttonOpens the selected examination data.5. Check in buttonChecks in the selected examination data.6. Check out buttonChecks out the selected examination data.7. Delete buttonDeletes the examination data and the thumbnail data.8. Copy buttonDisplays the examination data copy screen.9. DVD buttonDisplays the DVD writing screen.10. Disk space informationDisplays the free space of the selected drive.3. Back button2. Drive selection box1. Examination list4. Open button5. Check in button6. Check out button 7. Delete button8. Copy button9. DVD button10. Disk space information](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-32.png)
![192Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEMDisplaying the examination list screenThe following icons are displayed in the “Status” column of the examination list.Icon Caption ExplanationOriginal The examination data which has been downloaded from a recorder.Imported The examination data which is imported from a external storage to the workstation.With archive The archived examination data in the workstation.Checked out The examination data in the workstation which has been checked out.Password protected The examination data protected by a password.Anonymous The examination data from which the individual information has been removed.](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-33.png)
![Chapter 6 Capsule Endoscope Image Observation193OLYMPUS CAPSULE ENDOSCOPE SYSTEM1. Click the [List] button on the main screen (see Figure 6.64). The examination list screen is displayed.Figure 6.642. To exit the examination list screen, click the [Back] button (see Figure 6.65). Figure 6.65List buttonBack button](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-34.png)
![194Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEMChecking out the examination dataYou can copy the examination data and thumbnail data from the workstation onto an external drive, and edit the copied thumbnail data. You cannot edit thumbnail data on the source workstation until the copied data is restored to the workstation. This is referred to as the “check-out” function.1. From the examination list on the examination list screen, select the examination data associated with the thumbnail data you wish to check out.2. Click the [Check Out] button (see Figure 6.66). The thumbnail data selection screen is displayed.Figure 6.663. From the thumbnail data list on the thumbnail data selection screen, select the thumbnail data you want to check out (see Figure 6.67).Figure 6.67To create a new thumbnail data, select “New” (top row) from the examination data list.Check out button](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-35.png)
![Chapter 6 Capsule Endoscope Image Observation195OLYMPUS CAPSULE ENDOSCOPE SYSTEM4. Click the [OK] button (see Figure 6.68). The check-out destination selection screen is displayed.Figure 6.685. Use the drive selection box to select the drive to which the data is checked out and click the [OK] button. The examination data and the thumbnail data are copied to the check-out destination (see Figure 6.69).Figure 6.69The internal hard drive of the workstation cannot be selected. Select an external drive.• Check the “Password” checkbox to set a password for the check-out function.• If you specify a password when checking out the data, you will be required to enter the password to open the thumbnail data.• Click the [Cancel] button to exit the check-out destination selection screen.OK buttonDrive selection box](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-36.png)
![196Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEM• If there is insufficient storage space on the selected check-out destination, you can make free space by deleting the unnecessary files.• While copying the data to the check-out destination, a progress screen will be displayed. To stop the copying process, click the [Cancel] button on the progress screen.• The examination data (∗∗∗.opg) and the thumbnail data (∗∗∗.xml) is exported to the following location.(∗) Words in parentheses vary according to the check out data.](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-37.png)
![Chapter 6 Capsule Endoscope Image Observation197OLYMPUS CAPSULE ENDOSCOPE SYSTEMChecking In the thumbnail dataOnce you have finished editing the checked out thumbnail data, you must return it to the source workstation. This is referred to as the “check-in” function.1. Select the checked out examination data and click the [Check in] button (see Figure 6.70). The check-in source selection screen is displayed.Figure 6.702. Use the drive selection box to select the drive that contains the checked out thumbnail data which you wish to check in (see Figure 6.71).Figure 6.71Only external drives can be selected.Check in buttonDrive selection box](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-38.png)
![198Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEM3. Click the [OK] button (see Figure 6.72). The thumbnail data selection screen is displayed.Figure 6.724. From the list of thumbnail data, select the thumbnail data you wish to check in (see Figure 6.73).Figure 6.73OK buttonThumbnail data](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-39.png)
![Chapter 6 Capsule Endoscope Image Observation199OLYMPUS CAPSULE ENDOSCOPE SYSTEM5. Click the [OK] button (see Figure 6.74). The thumbnail data being checked in is saved, and the check-in process is complete.Figure 6.74If you select “New” from the list of thumbnail data when checking out the data and do not make the thumbnail data on Endo Capsule Software Light, you can not check in the thumbnail data. To release a check-out, see “Releasing the check-out” on page 200.OK button](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-40.png)
![200Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEMReleasing the check-outIf the checked out thumbnail data cannot be checked in, perform the following steps to release the check-out.If you release a check-out, the checked out data cannot be saved.1. Log in as an administrator.2. Click the [List] button on the main screen (see Figure 6.75). The examination list screen will appear.Figure 6.753. Select the checked out examination data (see Figure 6.76).Figure 6.76List buttonExamination data](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-41.png)
![Chapter 6 Capsule Endoscope Image Observation201OLYMPUS CAPSULE ENDOSCOPE SYSTEM4. Right-click the examination data and select “Check out” from “Reset” in the context menu (see Figure 6.77). The check-out is released.Figure 6.77](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-42.png)
![202Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEMImporting examination data from external drives onto the workstationYou can import examination data from a DVD or an external drive (such as an external hard disk) onto the workstation.1. Using the drive selection box on the examination list screen, select the external drive that contains the examination data (see Figure 6.78).Figure 6.782. From the examination list, select the examination data you wish to import onto the workstation (see Figure 6.79).Figure 6.79Drive selection boxExamination data](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-43.png)
![Chapter 6 Capsule Endoscope Image Observation203OLYMPUS CAPSULE ENDOSCOPE SYSTEM3. Click the [Import] button (see Figure 6.80). The thumbnail data selection screen is displayed.Figure 6.804. From the list of thumbnail data, select the thumbnail data you wish to import.5. Click the [OK] button (see Figure 6.81). The examination data and the selected thumbnail data are imported onto the workstation.Figure 6.81• If there is insufficient storage space on the internal hard drive of the workstation, the error message will be displayed.• “Cannot import data because workstation does not have sufficient disk space” message is displayed. Create enough disk space to import data.Import buttonOK button](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-44.png)
![204Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEMCopying examination and thumbnail data1. Select the examination data you wish to copy and click the [Copy] button on the examination list screen (see Figure 6.82). The copy screen is displayed.Figure 6.82• You can select multiple examination data simultaneously. The thumbnail data associated with the selected examination data will be copied automatically.• To exit the copy screen, click the [Cancel] button.2. Use the drive selection box to select the destination drive on the copy screen (see Figure 6.83). The amount of available disk space on the selected drive is displayed.Figure 6.83The folder for the examination data will be created automatically during the copying process.Copy buttonDrive selection box](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-45.png)
![Chapter 6 Capsule Endoscope Image Observation205OLYMPUS CAPSULE ENDOSCOPE SYSTEM3. The selected examination data which you wish to copy is displayed. (see Figure 6.84).Figure 6.844. Click the [Option] button to display the data copy options screen (see Figure 6.85).Figure 6.855. Select the type of files to be copied together with the examination data. Click the [Picture] button to copy still images, and the [Movie] button to copy video files (see Figure 6.86).Selected examination dataOption button](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-46.png)
![206Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEMFigure 6.86All items are selected by default.6. Click the [OK] button to save the settings and exit the data copy options screen (see Figure 6.87).Figure 6.87Picture buttonMovie buttonOK button](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-47.png)
![Chapter 6 Capsule Endoscope Image Observation207OLYMPUS CAPSULE ENDOSCOPE SYSTEM7. Check the “Password” checkbox to set a password (see Figure 6.88).Figure 6.88If you specify a password when copying the examination data, you will be required to enter the password to open the copied examination data.8. Check the “Make anonymous” checkbox to copy the examination data with the individual information removed (see Figure 6.89).Figure 6.89• Individual information removed include “Patient name” and “Image showing individual information”.• To remove “Image showing individual information”, you will need to set the hiding feature. For more information, refer to “Hiding images” on page 216.PasswordcheckboxMake anonymouscheckbox](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-48.png)
![208Chapter 6 Capsule Endoscope Image ObservationOLYMPUS CAPSULE ENDOSCOPE SYSTEM9. Click the [OK] button on the data copy screen (see Figure 6.90). The selected examination data will be copied. The progress screen is displayed while the examination data is being copied.Figure 6.90• To stop the copying process, click the [Cancel] button on the progress screen.• If there is insufficient storage space on the copy destination, an error message will be displayed. In this case, refer to Chapter 8, “Troubleshooting” on page 233.• Do not remove an external storage device while copying. Copying will fail and if may cause hang-up of the workstation.10. When the copying of examination data is complete, you will be returned to the examination list screen.OK button](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-49.png)
![Chapter 6 Capsule Endoscope Image Observation209OLYMPUS CAPSULE ENDOSCOPE SYSTEMDeleting examination and thumbnail dataThe examination data which has not been archived can not be deleted.1. Select the examination data you wish to delete and click the [Delete] button on the examination list screen (see Figure 6.91). The examination data deletion screen is displayed (see Figure 6.91).Figure 6.91• You can select multiple examination data simultaneously.• To exit the screen, click the [Cancel] button.2. The selected examination(s) which you wish to delete is displayed (see Figure 6.92).Figure 6.92Delete buttonSelect examination data](https://usermanual.wiki/Olympus-Medical-Systems/EC-1.Users-manual-Part-4/User-Guide-618772-Page-50.png)