Ohsung Electronics URCMRX2 Network Base Station User Manual EMISSION TEST REPORT

Ohsung Electronics Co., Ltd. Network Base Station EMISSION TEST REPORT

User Manual

G Order Number : GETEC-C1-13-112 FCC Part 15 subpart B Test Report Number : GETEC-E3-13-029 Page 1 / 1 EUT Type: Network Base Station FCC ID.: OZ5URCMRX2 APPENDIX G : USER’S MANUAL
MRX-2 Owner’s ManualNetwork Base Station
MRX-2 Owner’s Manual ©2013 Universal Remote Control, Inc.The information in this manual is copyright protected. No part ofthis manual may be copied or reproduced in any form without priorwritten consent from Universal Remote Control, Inc. UNIVERSAL REMOTE CONTROL, INC. SHALL NOT BE LIABLEFOR OPERATIONAL, TECHNICAL OR EDITORIALERRORS/OMISSIONS MADE IN THIS MANUAL. The information in this manual may be subject to change withoutprior notice. Complete Control is a registered trademark of Universal RemoteControl, Inc. All other brand or product names are trademarks or registeredtrademarks of their respective companies or organizations.500 Mamaroneck Avenue, Harrison, NY 10528 Phone: (914) 835-4484 Fax: (914) 835-4532
TABLE OFCONTENTSIntroduction 1Features and Benefits 2Parts Guide 3Front and Rear Panel Descriptions 4Network Installation 6Specifications 7USA Limited Warranty Statement 8Federal Communication Commission Interference Statement 10Declaration of Conformity 11
Page 1IntroductionThe MRX-2 Network Base Station allows for control of yourcomponents by sending infrared and serial commands to your system.This base station can be used with either a Total Control or aComplete Control system.When used in a Total Control System:Expand zones throughout the home or commercial space byinstalling multiple MRX-2’s.Control equipment such as shades and TV lifts using the basestations sensors, relays and RS-232 ports.Control URC RF Lighting using the optional RFTX-1 transmitter.When used in a Complete Control System:The MRX-2 is required to use the CC Control App for iOS devices,like the iPad and iPhone.Extend control to other rooms by installing multiple MRX-2’sthroughout the home or commercial space.The MRX-2 offers traditional IR only control from compatibleURC MX series remotes via an optional RFX-250.MRX-2 NETWORK BASE STATION
Page 2Features and BenefitsWhen used in a Total Control System:Expand Control: Add an MRX-2 to a Total Control system toexpand control to other rooms/areas in the home or office.Components located out of reach from the MRX AdvancedNetwork System Controller may be controlled via IR, RS-232 orRelays by using an MRX-2 to expand the scope of a TotalControl system.Lighting Control: By connecting an optional RFTX-1 RFTransmitter, take control of your URC lighting (within range).Control a specific light, a whole room or even the entire homefrom any remote control or iOS device. When used in a Complete Control System:Enables iOS Control: The addition of an MRX-2 base station toa control system, allows for control via URC’s CC Control iOSapp for iPads, iPhones and iPod touch. Each iDevice requiresprogramming by a qualified custom install professional. Note: Requires the purchase of CC Control Setup code (onecode per system).No Aiming: Using a base station results in flawless control ofyour components without having to aim the remote! The signaltravels to the base station via RF or Wi-Fi and is then convertedback to infrared before being sent to the device beingcontrolled; perfect for hidden components. Note: An optional RFX-250 Antenna is required for use withURC remote controls.MRX-2 NETWORK BASE STATION
Page 3MRX-2 NETWORK BASE STATIONParts GuideThe MRX-2 Network Base Station includes:1 - MRX-2 Network Base Station1 - 12V-1000mA Power Supply6 - Visible Emitters with 10 foot plugin cables including 1 pink sleevedemitter for the RFTX-1 port1 - Two Meter 3.5mm Stereo to3.5mm Stereo (for daisy chainingmultiple MRX-2 with one RFX-250)1 - Adjustment Tool1 - Mounting Plate for wall mountingthe MRX-2
Front and Rear Panel DescriptionsFrontThe front panel consists of 4 indicator lights which will illuminatewhen in use.Power:Illuminates when the power supply is connected to an outlet.Status: Flashes blue when an RF or Network signal is received.Sensor: Illuminates to indicate when the sensor is activated.Ethernet: Illuminates when connected to an active network.Reset: Press the Reset button located under the MRX-2 to restart theunit.Power Status Sensor Ethernet Reset: BottomMRX-2 NETWORK BASE STATIONPage 4
RearThe rear panel ports are:Power: Uses the included 12V/1Amp power supply.LAN: Plug an ethernet cable (RJ45) to the LAN(Local Area network). Relay NO, NC, COM: Configurable switch closure control.RS-232 Ports: Two RS232 ports provide direct control. Sensor: Connect with one of URC’s or compatible third party,sensors.IR IN:Allows MRX-2 control from a base station such as a MRF-260.Note:IR Routing is lost from commands received from this input.IR Outputs: Connect emitters for IR control of connected devices. RFTX Port: Dual port #6 for the RFTX-1 connecting cable orincluded sleeved IR emitter. RF IN: Connects to an optional single RFX-250 (Only for MX seriesproducts.)RF Out: Used for daisy chaining MRX-2s for RF Operation (Refer tothe RFX-250 manual.)RF ID: 15 unique RF ID's provide RF control and routing to multipleMRX-2’s in the same home. Note: DO NOT USE RF ID #0, as it is the interference "sniffer", usedto detect RF interference in the area.Page 5EthernetPower Relay:NO,NC, COMRS-232 PortsSensorIR INIR Outputs: #1-6RFTX Port: #6RF IN RF OutRF IDMRX-2 NETWORK BASE STATION
Page 6MRX-2 NETWORK BASE STATIONNetwork InstallationThe MRX-2 can be installed in either a Total Control or a CompleteControl System. Connect the Ethernet cable (RJ45) to the rear of theMRX-2 and the other end to the active network.Total Control InstallComplete Control Install
Page 7MRX-2 NETWORK BASE STATIONSpecificationsNetwork: One 10/100 Ethernet portRelay: One relay configurable to be NO, NC or MomentarySensor: One sensor supports Video or Voltage sensing via URCsensors.RS-232: Two RS-232 ports support TX, RX and GND two waycommunication via URC cables.IR: Six adjustable IR ports enable the included URC emitters tocontrol IR devices Note: 6th IR Output requires the includedsleeved emitter (identified by a pink connector), since it canoptionally be used to connect an RFTX-1Weight: 8.4 oz. Size: 248 x 120mm x28mmPower: 12V External Power Supply
Page 8MRX-2 NETWORK BASE STATIONUSA Limited Warranty StatementYour Universal Remote Control, when delivered to you in new condition,is warranted against defects in materials or workmanship as follows:UNIVERSAL REMOTE CONTROL, INC. warrants this product againstdefects in material or workmanship for a period of one (1) year and as setforth below. Universal Remote Control will, at its sole option, repair theproduct using new or comparable rebuilt parts, or exchange the productfor a comparable new or rebuilt product. In the event of a defect, theseare your exclusive remedies.This Limited Warranty covers only the hardware components packagedwith the Product. It does not cover technical assistance for hardware orsoftware usage and it does not cover any software products whether ornot contained in the Product; any such software is provided "AS IS" unlessexpressly provided for in any enclosed software Limited Warranty. To obtain warranty service, you must deliver the product, freight prepaid,in its original packaging or packaging affording adequate protection toUniversal Remote Control at the address provided in the Owner's Manual.It is your responsibility to backup any macro programming, artwork,software or other materials that may have been programmed into yourunit. It is likely that such data, software, or other materials will be lostduring service and Universal Remote Control will not be responsible forany such damage or loss. A dated purchase receipt, Bill of Sale, InstallationContract or other verifiable Proof of Purchase is required. For productsupport and other important information visit Universal Remote Control'swebsite: http://www.UniversalRemote.com or call the Customer ServiceCenter (914) 835-4484. This Limited Warranty only covers product issues caused by defectsin material or workmanship during ordinary consumer use. It doesnot cover product issues caused by any other reason, including butnot limited to product issues due to commercial use, acts of God, third-party installation, misuse, limitations of technology, or modification ofor to any part of the Universal Remote Control product. This LimitedWarranty does not cover Universal Remote Control products sold asUSED, AS IS, REFURBISHED, so-called “B STOCK” or consumables(such as batteries). This Limited Warranty is invalid if the factory-appliedserial number has been altered or removed from the product. This LimitedWarranty is valid only in the United States of America. This LimitedWarranty specifically excludes products sold by unauthorized resellers.
Page 9MRX-2 NETWORK BASE STATIONLIMITATION OF REMEDIESUNIVERSAL REMOTE CONTROL SHALL NOT BE LIABLE FOR ANYINCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OFANY EXPRESS OR IMPLIED WARRANTY OR CONDITION ON THISPRODUCT. IN NO EVENT SHALL UNIVERSAL REMOTE CONTROLBE LIABLE, WHETHER IN CONTRACT OR IN TORT (INCLUDINGNEGLIGENCE) FOR DAMAGES IN EXCESS OF THE PURCHASEPRICE OF THE PRODUCT, ACCESSORY OR SOFTWARE, OR FORANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIALDAMAGES OF ANY KIND, OR LOSS OF REVENUE OR PROFITS,LOSS OF BUSINESS, LOSS OF INFORMATION OR DATA, SOFT-WARE OR APPLICATIONS OR OTHER FINANCIAL LOSS ARISINGOUT OF OR IN CONNECTION WITH THE ABILITY OR INABILITYTO USE THE PRODUCTS, ACCESSORIES OR SOFTWARE TO THEFULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, THEREIS NO OTHER WARRANTY EXPRESSED OR IMPLIED. UNIVERSALREMOTE CONTROL WILL NOT BE HELD RESPONSIBLE FOR STATE-MENTS MADE BY OTHERS CONCERNING THE MERCHANTABILITYOR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT.Some states or jurisdictions do not allow the exclusion or limitation ofincidental or consequential damages, or allow limitations on howlong an implied warranty lasts, so the above limitations or exclusionsmay not apply to you. This Limited Warranty gives you specific legalrights and you may have other rights which vary from state to state orjurisdiction to jurisdiction.REV020708
Page 10MRX-2 NETWORK BASE STATIONFederal Communication CommissionInterference StatementThis equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instruc-tions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installa-tion. If this equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on, theuser is encouraged to try to correct the interference by one more of the follow-ing measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different fromthat to which the receiver is connected.Consult the dealer or an experienced radio/TV technician forhelp.Warning!Changes or modifications not expressly approved by the manufacturer couldvoid the user's authority to operate the equipment.Note : The manufacturer is not responsible for any Radio or TV interferencecaused by unauthorized modifications to this equipment. Such modificationscould void the user's authority to operate the equipment.FCC CautionThis device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) this device may not cause harmful interference,and (2) this device must accept any interference received, including interferencethat may cause undesired operation.Any changes or modifications not expressly approved by the party responsiblefor compliance could void the authority to operate equipment.
Page 11MRX-2 NETWORK BASE STATIONDeclaration of ConformityCompany Name : OH SUNG ELECTRONICS CO., LTD.Company Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, REPUBLIC OF KOREAContact Information : Phone: +82-54-468-7281, Fax: +82-54-461-8368Brand Name : UNIVERSAL remote controlProduct Name : Network Base StationModel Name : MRX-2This product herewith complies with the requirements of EMC Directive (2004/108/EC)issued by the Commission of the European CommunityCompliance with these directives implies conformity to the following European CommunityEMC DirectiveEN 55022EN 55024EN 61000-3-2EN 61000-3-3List of test reports and/or certificate verified compliance with the standards aboveDate of issue : January 30, 2013Name and signature of authorized person :EMC DirectiveReport No.Testi ng Labora tory : Gumi College EMC CenterJames NovakSenior Product ManagerUniversal Remote Control Inc.
500 Mamaroneck Avenue, Harrison, NY 10528 Phone: (914) 835-4484 Fax: (914) 835-4532 www.universalremote.comOCE-0076D Rev 01

Navigation menu