OTF Distribution OT-BURN-1 Otbeat burn User Manual

OTF Distribution LLC Otbeat burn Users Manual

UserManual.wiki >

OTF Distribution >

OT-BURN-1 User Manual >

Contents

1. Users Manual
2. User Manual

User Manual

burnQuick Start Guide

1. Getting Started2. Downloading the Orangetheory App 3. Charging Device 4. Proper Placement 5. Pairing Device6. LED Guide 7. Caring for Device8. Technical Specifications OTbeat Burn Quick Start Guide Instructions for:Downloading the Orangetheory App:Orangetheory App*Using your mobile device, download the Orangetheory App.Note: Fully charge device before attempting to pair for the first time.Page 2 1. Included in packaging: OTbeat Burn, SM band, LG band, & USB cord2. Remove OTbeat Burn from packaging 3. Connect USB cord into charging port of device4. LED light will appear after a few seconds Getting Started:

(BACK OF OTBEAT BURN)OTbeat Burn - Charging DeviceDevice can be connected directly to a computer USB port.Note: The voltage differs from wall outlet to computer.Battery is fully charged when Green LED is continuously onDuring charging: Red LED light will blink slowlyLED indication for charging is in front of deviceCharging Device:1. Open rubber port cover on back of device2. Plug in mini-USB connector into device port3. Plug in regular USB connector into charging block4. Plug in charging block into wall outletOptical heart rate sensorLED lightsPage 3

OTbeat Burn - Proper PlacementTo transmit accurate data from your device:1. Fasten device snugly in one of the below placement options2. Wear device below, and not directly on top, of wrist bone* or elbow3. The optical sensor on the back should make good contact with skin*For placement on wrist, measure two fingers above wrist boneWrist bone----------------------------------------Elbow----------------------------------------Page 4Proper Placement:

OTbeat Burn - Pairing DeviceSet power OFF: Long button press(Red LED light continuously on for 2 seconds then turns off)Set power ON: Short button press(Blue LED blinks for 5 seconds)Pairing Device:1. Once OTbeat Burn is fully charged, press center of splat to power ON the deviceEvent LED lightPage 5

Pairing Device (Cont.):2. Launch the settings app on your mobile device3. Ensure your bluetooth settings are onOTbeat Burn - Pairing DeviceOFFONPage 6

Pairing Device (Cont):4. Open Orangetheory app on mobile phone.OTbeat Burn - Pairing DevicePage 7

Pairing Device (Cont.):5. Use the Orangetheory app to search for device*Once device appears, OTbeat Burn is successfully connected to app OTbeat Burn - Pairing DevicePage 8

OTbeat Burn - LED GuideLED Guide:Heart Rate Detection LED Indication:Alternating BLUE and GREEN: Detecting heart rateAlternating BLUE and RED: No heart rate detectedBlinking GREEN: Heart rate detectedBlinking ORANGE: Heart rate zones are changingBluetooth Connection State:Blue LED blinks for 5 seconds: After turning on the unitBlue LED continuously on for 5 second: ConnectedGreen LED on for 2 seconds: Connected (HR not detected)Green LED continuously on: Updating firmwarePage 9Battery LED LightDuring Charging:Red LED blinks slowly: Charging Green LED continuously on: Battery fullBattery State:Red LED blinks three times: Low battery at <15% (repeat every 5 min. until reach critical level)Red LED continuously on for 2 sec: Device powering off

OTbeat Burn - Caring for DeviceCaring for Device:1. To ensure accurate readings, clean the sensor lens with a soft cloth2. OTbeat Burn unit and strap are waterproof to IP67 specifications and can be easily cleaned with mild soap and cool water3. Use a cotton swab and only rubbing alcohol to clean the USB charging contacts when necessary: do not contact USB charging port4. Do not use any abrasive chemicals to clean the Otbeat Burn unit, sensor, or strap. This will cause permanent damagePage 10

OTbeat Burn - Technical SpeciﬁcationsTechnical Specifications:Description Feature heart rate detection and transmission(ANT+ or Bluetooth 4.0), battery low alert Functions 30 to 220 BPM in 1 BPM resolutionHeart Rate Range +/-5 BPMHeart Rate AccuracyANT+ /BLETransmission3.8V Li-ion Polymer rechargeable batteryPower Supply IP67Water Resistance Level -20 to +60◦CStorage Temperature 6 hours detectionMemory capacity0 to +40COperating Temperature 15 MetersANT+ or BLE Transmission DistanceUp to 24 hours of continuousdetectionBattery Life time (PPG&BLE always on)Page 11

burnFor more information visit orangetheoryfitness.com/otbeat

Navigation menu