Nutek NTRLF Transceiver User Manual

Nutek Corporation Transceiver

User Manual

Status LightsValet Switch RF-50-EDP / RF-30-EDP / RF-10-EDPRange Extender / OEM Upgrade KitInstallation GuideIS_RF-X0-EDP 10/19/2012Feature Programming: Ignition on, off, press valet 5 times# Feature Lock Button or Brake Pedal x 1Unlock button or Brake Pedal x 2Trunk button or Brake Pedal x 3”START” button or Brake Pedal x 41 Ignition Lock/Unlock On Lock only Unlock only Off2 Last Door Locking On Off3 Automatic Relocking On Off Enhanced4 Unlock w/ Trunk Release On Off5 Remote Start Activation 1 press 2 presses 3 presses 4 pressesStep 1 Turn the ignition key “ON”, then “OFF”Step 2 Within 5 seconds of step 1, press the valet switch 5 times to access features ~ The built in beeper will sound and the status light will turn on.Step 3 Within 10 seconds of step 2, press the valet switch the number of times cor-responding with the desired feature’s number. ~ The built in beeper will chirp equal to the selected feature.Step 4 for RF-50-EDP & RF-30-EDP Change the feature by pressing the transmitter button that corresponds with the desired setting. Step 4 for RF-10-EDP Turn the ignition key back “ON”, some brake circuits require ignition power to operate. Change the feature by pressing the brake pedal the number of times that corresponds with the desired setting. ~ The built in beeper will chirp equal to the selected setting.Step 5 If you wish to change more features, repeat steps 3 & 4 at this time.Step 6 To exit programming, turn the ignition key “ON” then “OFF”. Or, you can wait 10 seconds for programming mode to expire.PROGRAMMING FEATURESProgrammable FeaturesWiring OverviewLock (-) Input - BROWNRemote Start Activation (-) Input - RED/WHITEUnlock (-) Input - PURPLE/YELLOWAdding Omega-Carlink Directly To RS Firmware KitConnect the Carlink AUX outputs to these inputs and program the outputs for “1 second pulse” in the installation details during activation/conguration.Visit www.omegaweblink.com/rs for more info and current vehicle applications.RF-X0-EDPOmega Carlink Input Trigger Wires {5 AMPConstant 12 v (+) Input - RED (Not required if using a T-harness)Chassis Ground (-) Input - BLACK (Not required if using a T-harness)Omegalink module ashed with RS rmware~ REQUIRED ~Window module/antenna: Mount to windshield for easy access and visibility.Programming Transmitters/ControllersStep 1 Have all transmitters which are to operate the system at hand. Then, turn the ignition “on”.Step 3 2-way and 4-button controllers: Press the “lock” button on each transmitter one at a time. When the rst controller is learned, all previous controllers are erased from memory. The transmitter’s other three button’s functions will automatically be assigned when the “lock” button is learned. 1-button controllers: Press the “start” button on each transmitter one at a time. When the rst controller is learned, all previous controllers are erased from memory. The antenna will beep once to conrm that each was learned.NOTE: If a code is not received within a 10 second period, the learning process will automatically terminate, as indicated by a long beep. Step 2 Within 5 seconds of turning on the ignition, press the Valet Switch 5 times. The beeper in the antenna will briey sound, conrming that for the next 10 seconds the system is ready to learn a transmitter/controller code. Installation Overview1) Install the Omegalink RS module per the instructions provided with the chosen rmware and test for proper operation.2) Connect to the Omegalink RS module: If using a T-harness - Connect one end of the ribbon harness to the 4 pin black connector on the T-harness. The T-harness will supply power and ground to the antenna module. The RED power and BLACK ground wires aren’t used so make sure they are cut/capped to prevent a short circuit. If NOT using a T-harness - Connect one end of the ribbon harness to the 4 pin black connector on the RS module. Connect the RED wire to a constant +12 volt source and connect the BLACK wire to a good chassis ground point free of paint, grease, or dirt. This will provide power to the RF module and the Omegalink RS module.3) Connect to the RF-X0-EDP antenna module: Connect the other end of the 4 pin ribbon harness to the antenna module and test for all primary functions.4) Mount the antenna module: Choose a mounting location high on the windshield for best operating range. Be sure that the location will not obstruct the driver’s view and is easily reached to access the valet switch. Route the ribbon harness up the A-pillar to your chosen location avoiding sharp or moving objects in the vehicle. Clean the mounting surface and attach the antenna module with the provided double-stick tape.www.caralarm.com | www.omegaweblink.com | www.wiresheet.com | www.facebook.com/omegard | 800.554.4053
This device complies with FCC Rules Part 15 Operation is subject to the following two conditions (1) This device may not cause harmful interference and (2) this device must accept any interference that may be received, including interference that may cause undesired operation. NOTE:The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. FCC ID:ELVNTRLF

Navigation menu