Nutek MTIB Transmitter User Manual PLUS6900 UM qxp

Nutek Corporation Transmitter PLUS6900 UM qxp

Contents

rev1 User s Manual Part 2

7Flash Function1 Flash System is Armed2 Flashes System is Disarmed3 Flashes Disarmed / Triggered3 or 6 Flashes Car LocatorConstant On or Flashing Under Remote StartChirp Function1 Chirp System is Armed2 Chirps System is Disarmed3 Chirps Ajar Warning4 Chirps Disarm / Triggered2,3,6 Chirps Progressive Car LocatorSiren/Horn LED Doors Starter Dome Light1. Arming 1 or 3 Chirps 1 Flash Slow Flash Locking Disabled(Option)2. Disarming 2 or 4 Chirps 2 or 3Flashes Unlocking Turns on for30 Seconds3. Trigger Alarming Flashes Slow Flash Disabled(Option) Flashes4. Panic Alarming Flashes Flashes5.CarJacking Alarming Flashes Disabled(Option) Flashes6.CarLocator 2,3,6 Chirps 3,6 FlashesParking Light IndicatorsChirp IndicatorsSystem CharacteristicsParkingLightPLUS6900-UM.qxp 4/3/2009 1:18 PM Page 7
81. Press the button on the transmitter.2. The siren will chirp once and parking lights will flash once indicating that the system is nowarmed. The vehicle door will lock upon arming when interfaced with the security system.Ajar Warning:If the siren sounds 3 chirps,then you have left a door,trunk, or hood lid ajar.Silent Arming/DisarmingPress the transmitter and button at the same time to arm or disarm your security system. Nochirp sound will be heard. The arm/disarm confirmation will be through the vehicle’s parkinglights only.Shock Sensor BypassPress the button on the transmitter two times within 3 seconds. This will arm the securitysystem and bypass the shock sensor. The system will chirp one additional time to confirm thesensor Bypass Mode was activated. The sensor bypass feature is programmed to activate for onearming cycle only. The security system will return to normal operation during the next armingcycle.Hidden Alarm FunctionPress the button first, within 3 seconds press the button to activate the hidden alarmfunction. The security system will arm, but the siren / horn will be silenced even if the sensor istriggered in the armed status.Manual arming/disarming is controlling your security system via the remote transmitter. Thissecurity system is equipped with an optional Automatic Arming feature which allows the securitysystem to arm 45 seconds after the last door is closed. Operation is as follows:1. Turn the ignition to the “OFF” position and exit the vehicle.2. After all entrances are closed, the security system LED will flash fast for 45 seconds. If youreopen any Door, Hood, Trunk the security system LED will stop flashing. It will begin flashingagain once the vehicle’s entrances are closed.3. After the 45-second timer has elapsed, the security system will automatically “ARM”. Thesiren/horn will chirp once, and the parking lights will flash once.Automatic Arming with Automatic Door Locking (Programmable)If this feature has been programmed on, the vehicle doors will automatically lock after theautomatic arming cycle has been completed.System Armed Door Ajar Trunk/Hood AjarManual Lock/ArmAutomatic ArmingPLUS6900-UM.qxp 4/3/2009 1:18 PM Page 8
9Automatic Arming BypassWhile the system is in Disarmed Mode, press the button twice. The horn/siren will respondwith one chirp and the LED will turn “ON”. The security system will remain in this mode for aslong as you wish. To exit this mode press the or buttons and the system will return tonormal status.1. Press the button on the transmitter.2. The siren will chirp twice and parking lights will flash twice indicating that the system is nowdisarmed. The vehicle door will unlock and the dome light will turn on for 30 seconds upondisarming when interfaced with the security system.Tamper DisarmingIf the security system was triggered prior to disarming, the siren will chirp 4 times and theparking lights will flash 3 times. One of the enclosed panels will be displayed on the LCDtransmitter screen to indicate which sensor had been triggeredPathway IlluminationThis feature turns the parking lights “ON” for 30 seconds upon a unlock signal and for 10seconds upon the lock signal.Two Step Door UnlockThis feature will independently unlock the driver’s door only when disarming the securitysystem. Pushing the button a second time within 3 seconds will unlock the other doors.Automatic RearmIf this feature is selected, the security system will automatically rearm itself within 60 secondsafter disarming with the remote transmitter. Automatic rearm will cancel if any door is openedbefore the 60 second timer is up.The override function may be used if the remote transmitter is lost or inoperative. Override canbe done without password/pin number (this is the factory default setting). 1. Enter the vehicle and turn the ignition switch to “ON” position (alarm will sound).2. Within 10 seconds push and release the valet switch. The alarm will stop sounding and enterthe Disarm Mode. You can now start and operate the vehicle normally.Manual Un-Lock / DisarmDisarming without a TransmitterAutomatic Arming (Continued)Shock Sensor TriggeredDoors Triggered Trunk/Hood Triggered Ignition TriggeredPLUS6900-UM.qxp 4/3/2009 1:18 PM Page 9
10Manual valet mode allows you to bypass all alarm functions eliminating the need to hand yourtransmitter to parking attendants or garage mechanics. This mode is also a necessity if yourtransmitters become in-operable. When the system is in Valet Mode, all alarm functions andremote start functions are off. However, the remote panic feature and remote door locks remainoperational. To enter the Manual Valet Mode, the system must first be disarmed either by usingyour remote transmitter, or by operating the manual override sequence.Enter Valet Mode1. When in Disarmed Mode, turn the ignition to the “ON” position.2. Push and hold the valet switch for 2 seconds. The LED will flash every 5seconds as long as the unit is in the Valet Mode.Note: When the unit is in valet mode, the LCD transmitter icon will bedisplayedExit Valet Mode1. To return to normal operation, turn “ON” ignition.2. Push and hold valet switch for 2 seconds. The LED will stop flashing, indicating the system hasnow exited the Valet Mode.Note: When the unit is out of valet mode, the icon will be off and you will heara short melody from the transmitter..RF valet mode provides the same functions as manual valet mode but allows you to enter and exitthe valet mode using the remote transmitter. When the system is in Valet Mode, all alarmfunctions and remote start functions are off. However, the remote panic feature and remote doorlocks remain operational. To enter/exit the RF Valet Mode, repeat the following procedures. Enter Valet Mode1. In Disarmed Mode, open the drivers door.2. Push and hold the and transmitter buttons until the door locks cycle “Lock then Unlock”.The LED will flash every 5 seconds to indicate that the unit is in the Valet Mode.Note: When the unit is in valet mode, the LCD transmitter icon will be displayedExit Valet Mode1. In Unlocked Mode, open the drivers door.2. Push and hold the and transmitter buttons until the door locks cycle “Lock then Unlock”.The LED will stop flashing every 5 seconds to indicate that the unit is out of the Valet Mode.Note: When the unit is out of valet mode, the LCD transmitter icon will be off and you will heara short melody from the transmitter.Note: The remote vehicle location system is active 30 seconds after the alarm is armed. 1. Press the button to active the vehicle locator system. The horn/siren will beep 2 times andthe parking lights will flash 3 times. This operation will repeat a second time. 2. Press the button again within 30 seconds. The horn/siren will beep 3 times and the parkinglights will flash 3 times. This operation will repeat a second time.Hold 2 SecondsManual Valet ModeRF Valet Mode (Applies to All Transmitter Types)Progressive Remote Vehicle Locator SystemPLUS6900-UM.qxp 4/3/2009 1:19 PM Page 10
The transmitter can be used as a remote panic switch to manually trigger the alarm system incase of an emergency.1. Press and hold the button for 3 seconds to enter the Panic Mode (horn/siren will start tosound and parking lights will flash).2. While in Panic Mode the transmitter and buttons can be used to lock and unlock the door(if that option is installed). However, if the button is pressed, the vehicle’s starter disabledevice (when installed) will be disabled, allowing the vehicle to start.3. To turn off the panic function, press and hold the button again for 3 seconds or press andrelease the or buttons. 4. If the panic function is not turned off by the transmitter, it will turn off and reset itself after 30seconds.11Panic FeatureThe Security System has a unique feature for using your vehicle’s dome light:1. Upon disarming the vehicles security system, the interior dome light will remain on for 30seconds.2. If the security system is triggered, the dome light will flash for the same duration as thehorn/siren. Note: Turn “ON” the ignition switch or arm the system to turn off the dome light.Domelight SupervisionIf the vehicles door locks have been interfaced with the security system, the system willautomatically lock the doors 3 seconds after the ignition is turned “ON”, or unlock the doors whenignition key is turned “OFF”. Note: If a protected entrance is open, the doors will not lock. Press and hold the button for up to 3 seconds to activate the trunk release (Channel 3 output)and/or any other devices connected.Press and hold the and button at the same time to activate the Channel 4 output. Channel 4is user programmable timer output. You may program the built-in timer to send a ground signalfor any time duration from 1 second to 120 seconds. For example, this timer output may be usedto turn on the headlights, power window or sunroof (Factory defaults setting at momentaryoutput.)Ignition Key Controlled Door Lock/Un-LockChannel #3 Trunk Release OutputChannel #4 Timer Controlled OutputProgressive Remote Vehicle Locator System (Continued)3. Press the button again within 30 seconds. The horn/siren will beep 6 times and the parkinglights will flash 6 times. PLUS6900-UM.qxp 4/3/2009 1:19 PM Page 11
12Warning: This security system has a car jacking feature. Its default setting is “OFF”. So be sure toenable this feature if you feel it is needed.Active Anti-Car Jacking1. Press and hold the transmitter and buttons at the same time for 2 seconds with thevehicle’s ignition is “ON”. The parking lights will turn on for 1.5 seconds to indicate the systemhas entered the Anti-Car Jacking Mode.2. Once the system is armed in the Anti-Car Jacking Mode, the system will trigger when the dooris opened and closed while the ignition is “ON”.Automatic Anti-Car Jacking1. Turn the ignition switch to the “ON” position, and the system will enter the Anti-Car JackingMode. Note: Do not start the engine with the doors open. Close all entrances first. This willprevent a false trigger.2. Once the system is armed in the Anti-Car Jacking Mode, the system will trigger when the dooris opened while the ignition is “ON”.When the Anti-Car Jacking Feature is TriggeredA. 50 seconds after the system has been triggered. The siren will start chirping for 15 seconds. B. During this 15 second period of chirping, you can push and release the valet switch once toturn off the car jacking feature. C. 65 seconds after the system has been triggered. The siren starts sounding and the parkinglights start flashing. You must follow the override procedure to stop the system at this point.D. 90 seconds after the system has been triggered: 1. The siren will still be sounding and the parking lights flashing. 2. The starter disable will activate to prevent the vehicle from starting. 3. Anti-Car Jacking Mode will remain active until the override procedure is performed or thevehicle's battery power is exhausted. Override the System to Turn Off Anti-Car JackingTurn the ignition switch from OFF to ON, and within 10 seconds push the valet switch. The sirenwill stop sounding and the security system is now disarmed.Anti-Carjacking FeaturePLUS6900-UM.qxp 4/3/2009 1:19 PM Page 12
13If the Out-of-Range Indication feature is activated the system will automatically check the rangeevery 30 minutes after armed.1. If the user is within the range, the icon will display on the LCD screen.2. If user is out of range, the icon will disappear from the LCD screen and the transmitter willbeeps 5 times.Note: Activating this feature will decrease the life expectancy of battery. Driver Paging / Lost and Found is useful when someone inside the vehicle wantsto page the driver, or if the LCD transmitter has been misplaced. With the ignition switch in the “OFF” position, press and hold the valet switch for2 seconds to page the LCD transmitter. One chirp shall be emitted and thepaging melody continues sounding from the LCD transmitter and will flashon the screen.Driver Paging / Lost and Found (Applies to LCD Transmitter Only)Out of Range IndicationPLUS6900-UM.qxp 4/3/2009 1:19 PM Page 13
14This feature allows the vehicle to remain running after the key has been removed from theignition. It is useful on occasions when you wish to exit and lock the vehicle for a short period oftime, but keep the engine running allowing the climate controls to stay on.1. Before turning the engine off with the ignition key, press the button twice. The LED will flashthree times indicating the feature has been activated.2. Turn the ignition key to the “OFF” position (the engine will stay running).3. The engine will run until the pre-programmed time has elapsed or a shutdown input is received.Note: If the alarm system has been programmed to Auto-Arm, when you exit the vehicle theauto arming timer will start to count down and the vehicle will become armed within 45seconds. 1. Insert the ignition key, and turn it to the “ON” position, NOT the “START” position.2. Press the brake pedal.Note: If the brake pedal is pressed before the key is in the “ON” position, the engine willautomatically shut off.If the default method of remote starting has been reprogrammed to Child Safety Mode Operation,to remote start your vehicle is to press the and the buttons at the same time. Note: To turn off the remote start press the and the buttons at the same time. Remote Start Your Vehicle Using the Remote Transmitter1. Press the button twice on the transmitter.2. The parking lights will turn on indicating the remote start has received thesignal (A melody sound from your LCD transmitter and the icon willflash on the LCD screen to confirm the remote start was activated.)3. The engine will start in approximately 5 seconds.4. Once the engine is running, the parking lights will turn on again after a fewseconds, and the climate controls will activate and adjust the vehiclesinterior temperature to your preset setting. While the vehicle is running, thesmoke icon will flash on the LCD screen indicating the count down timerbased on the 5, 10, 20 or 30 minute run-time setup by the installer.5. The vehicle will run for 5 to 30 minute cycles and automatically shut down.(When the unit shuts off, the count down timer will turn off and thetransmitter will play a melody).Note: The Remote Start Unit will not start the vehicle if any one of thefollowingconditions exists:1. The hood is opened.2. The brake pedal is pressed.3. Move the optional remote start enable toggle switch to OFF position (if installed).4. The vehicle is in a gear other then “Park” or “Neutral”. EngineRunningSafe Start Mode (Child Safety Mode)Vehicle Operation when Running in Remote Start ModeTemporary Stop FeatureActivate Remote StartREMOTE START OPERATIONSPLUS6900-UM.qxp 4/3/2009 1:20 PM Page 14
Enter Timer Start:1. Press the button twice to remote start the vehicle. 2. Let the engine run and wait for the parking lights to turn on or start flashing. Press thebutton once then press and hold the button. The parking light will flash3 times and the siren or horn will chirp 3 times and the icon will appear onthe LCD display. The vehicle is now programmed to start every 3 hours.3. Press the brake pedal to shut off the engine.Exit Timer Start:1. Make sure the remote start system is not operating the engine.2. Turn the ignition “ON”. The LED and parking lights will flash 4 times. The hornchirps 4 times. The vehicle is no longer programmed to Timer Startautomatically.Or1. Press the button twice to remote start the vehicle.2. As soon as the parking lights have turned on or flashing, press the button once. Then pressand hold the button. The parking lights will flash 4 times. The siren or horn chirps 4 times.The vehicle is no longer programmed to Timer Start automatically.15When the engine is running by remote start and you wish to shut it off, followthese steps:1. While in Remote Start Mode, press the button twice on the remotetransmitter.2. Move the optional remote start toggle switch to the “OFF” position (ifinstalled).3. Press the vehicle’s brake pedal, the engine will stop running and the parkinglights will turn off to indicate the engine has been shut off.The disabling the Remote Start System feature allows your system’s remote start unit to betemporarily disabled, which prevents the vehicle from being remote started accidentally. This isuseful if the vehicle is being serviced or stored in an enclosed area. To disable the remote start,move the optional remote start enable toggle switch to the “OFF” position.Important! Timer Start should be used only in open areas. Never start or leave a vehicle running inan enclosed area such as a garage or carport.This unit can be programmed to auto-start and run the engine every 2 or 3 hours (3 hours is thedefault setting). The engine will run for the programmed run time and then shut down. Thisfeature is designed to prevent the engine from freezing in cold climates. A Maximum of Six Auto-Start Cycles can Occur.Timer StartingTurn Off Remote Start SystemToggle Switch Disable (If Installed) Timer Starting ModePLUS6900-UM.qxp 4/3/2009 1:20 PM Page 15
After arriving at your destination, Turbo Timer keeps the engine running for a programmable timeperiod of 1, 3 or 5 minutes. This allows the engine’s turbo charger time to conveniently cool downafter you have left the vehicle.To Activate:1. While the engine is running, set the emergency brake and place the transmission into "Park".2. Before turning off the engine, press and release and buttons at the same time. The parkinglights will flash indicating the remote start has entered Turbo Timer Mode.3. Remove the ignition key and the engine will keep running.4. Exit and secure the vehicle. The engine continues running until the pre-programmed time haselapsed.16If any of the following conditions exist while the system is operating, the engine will not start or willshut down immediately:1. The hood is opened.2. The brake pedal is pressed.3. Engine is over-revved (Tachometer Checking Type only).4. The preprogrammed run time (5/10/20/30 minutes) has elapsed.5. Press the button twice on the remote transmitter under Remote Start Mode.6. Move the optional remote start enable toggle switch to “OFF” position (if installed).7. The vehicle refused to start running after 3 unsuccessful attempts.Remote Start Shutdown InputsTurbo Timer ModePLUS6900-UM.qxp 4/3/2009 1:20 PM Page 16
Return to First Car Operation (LCD Remote Only)1. Press and hold and buttons at the same time until one long beep isheard. Programming Mode has now been entered.Note: No action for five seconds will generate two long beeps indicating theProgramming Mode has been exited.2. Within 5 seconds, press and hold the button until two beeping sounds areheard and the icon is not displayed on the LCD screen indicating first caroperation.17If your transmitters have been programmed to a second Marksman security system, follow thesteps below.For 1-Way Remote Control Transmitter:The 1-way backup transmitter does not have the ability to operate 2 systems. Only the 2-wayLCD transmitter can operate 2 didferent systems. For LCD Remote Control Transmitter:Second Vehicle Operation: While the icon is displayed on the LCD screen, you can remotecontrol and communicate with a second vehicle security system. 1. Press and hold and buttons at the same time until one long beep is heard.Programming Mode has now been entered.Note: No action for five seconds will generate two long beeps indicating theProgramming Mode has been exited.2. Within 5 seconds, press and hold the button until two beeping sounds areheard and the icon is displayed on the LCD screen indicating second caroperation.3. While the is displayed, press any button on the transmitter to control thesecond vehicle’s security system or alarm function (arm/disarm/trunk/remote start).Note: Button functions are the same for the second car as they are for the first car.Second Security System OperationThe LCD remote control is powered by a 1.5 Volt AAAAlkaline battery. When the power of the batteryweakens the battery icon will be displayed on thescreen. When the old battery is replaced with a newone, there will be a beep to indicate the power is up. Toreplace the battery, follow the steps in the illustrationat left.Note: Press the button two times when the batterycompartment is empty, then insert the new battery.Battery Replacement (Applies to LCD Transmitter Only)PLUS6900-UM.qxp 4/3/2009 1:21 PM Page 17
181-Way Remote for he PLUS5900 - PLUS6900 Security System CA-RF69 39.95 ea.2-Way LCD Remote forthe PLUS5900 - PLUS6900 Security System CARF-LCD2 79.95 ea.TRANSMITTERS DESCRIPTION MODEL # $ PRICEREPLACEMENT BATTERIES DESCRIPTION MODEL # $ PRICE1.5 Volt AAA Alkaline Battery commonlyfound in grocery stores, hardware stores,etc.3 Volt Lithium Battery (1 pc.)Replacement TransmittersReplacement BatteriesCR2032 4.95 ea.PLUS6900-UM.qxp 4/3/2009 1:21 PM Page 18
Credit Card or Money Order Only(Sorry No Cash, C.O.D. or personal checks accepted)SHIP TO: (No P.O. Boxes)LAST NAME FIRST NAME INITIALSTREET ADDRESSADDITIONAL ADDRESSE-MAIL ADDRESSCITY STATE ZIP CODEDAY TIME PHONE NUMBERPART # DESCRIPTION QTY. PRICE EACH TOTALSales Subtotal = ________ . ______California Residents Add Sales Tax = ________ . ______ Shipping and Handling (See Chart) = ________ . ______TOTAL = ________ . ______On regular orders please allow 4-5 weeks for delivery.Please give a shipping address where this order may be delivered between the hours of 9 am and 5 pm weekdays.If UPS is unable to deliver, your order will be returned and additional shipping charges will be required.CREDIT CARD INFORMATIONCREDIT CARD N0. EXPIRATION DATECARD HOLDER’S LAST NAME FIRST NAME INITIALSTREET ADDRESSCITY STATE ZIP CODEMail to: Magnadyne CorporationATTN: Consumer Parts SalesP.O. Box 5365Carson, CA 90749-5365Shipping and HandlingUp to $20.00 $6.0020.01 to 30.00 6.9530.01 to 45.00 7.5045.01 to 70.00 8.95Over 70.01 9.95VISAMC Call: (310) 884-7777 Fax: (310) 637-954219Replacement Parts Order FormPLUS6900-UM.qxp 4/3/2009 1:21 PM Page 19
PLUS6900-UM 4-03-09 Rev. A© Copyright 2009 Magnadyne CorporationLimited Lifetime WarrantyMagnadyne Corporation or its authorized agents will, for the life of the vehicle and to the originalpurchaser, repair, replace or refund the retail sales price of said product or any part thereof, at theoption of the Magnadyne Corporation or its authorized agents, if said product or part is founddefective in materials or workmanship, when properly connected and operating on the correctpower requirements designated for the specific product. This warranty and Magnadyne Corporationor its authorized agents obligations, hereunder do not apply where the product was: damaged whilein the possession of the consumer, subjected to unreasonable or unintended use, not reasonablymaintained, utilized in commercial or industrial operation, or serviced by anyone other thanMagnadyne Corporation or its authorized agent, or where the warning seal on the product is brokenor the power plugs or wires are detached from the unit. Magnadyne Corporation or any of itsauthorized agents do not assume any labor costs for the removal and reinstallation of any productfound to be defective, or the cost of transportation to Magnadyne Corporation or its authorizedagents. Such costs are the sole responsibility of the purchaser.This warranty does not cover the cabinet, appearance items, normal wear and tear or accessoriesused in connection with the product resulting from improper installation, alteration, accident,misuse, abuse or acts of nature.This Limited Life Time Warranty applies only to the receiver section of the security system. Neitherthe siren, transmitters, wire harness or any accessory item added to or used with a Remote Mobilesecurity system are covered by this Limited Life Time Warranty. Sirens, transmitters, wire harnessor any accessory item are covered by our standard 12 month limited warranty.Magnadyne Corporation or its authorized agents shall not be liable to anyone for consequentialor incidental damages or claims that may arise due to failure of product to operate properlyexcept those accorded by law. Magnadyne's or its authorized agents liability to the repair,replacement of the product as stated above if all conditions of the warranty are met. Noexpressed warranty or implied warranty is given except those set forth herein. Magnadyne doesnot warrant or guarantee against break in damage or the theft of the vehicle in part or whole, oragainst the loss or damage to the contents of any vehicle in which a security system isinstalled. Magnadyne security systems are only a deterrent against possible theft.This warranty extends only to the original purchaser of the product and for the vehicle in which itwas originally installed. This warranty is not transferable or assignable to any person or vehicle.Defective merchandise should be returned to the original point of purchase or secondly toMagnadyne Corporation, 1111 W. Victoria Street, Compton, CA 90220. A return authorization mustbe obtained before sending, or merchandise may be refused.PLUS6900-UM.qxp 4/3/2009 1:21 PM Page 20

Navigation menu