Nortek Security and Control SST00127 Security/Remote Control Transmitter User Manual 232812A indd

Nortek Security & Control LLC Security/Remote Control Transmitter 232812A indd

user manual

DXS-36AFSUPERVISEDDOOR/WINDOWTRANSMITTERInstallation InstructionsDXS-31AF FEATURES & ACCESSORIESPRINTER’S INSTRUCTIONS:INSTR,INSTL,DXS-36AF - LINEAR P/N: 232812 X4 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” X 11.000” - SCALE: 1-1 - SIDE 1 OF 2PRODUCT DESCRIPTIONThe DXS-36AF is a battery powered stationary transmitter designed for use with AlarmForce receivers. Triggering the transmitter with its built-in magnetic switch or an external switch sends a digitally coded wireless signal to its companion receiver. The DXS-36AF can send fi ve different signals: alarm, restore, low battery, status, and tamper.The digital code format used in the transmitter features over a million possible codes. The transmitter is pre-coded at the factory to a unique system code, so no fi eld coding is required. The receiver must be programmed to the transmitter’s system code before testing and operation. Refer to the receiver’s instructions for details on programming.In a typical installation, the magnet is mounted on a door or window and the transmitter is mounted on the frame. When the magnet moves more than 1/2” away from the transmitter, an alarm signal is sent. When the magnet returns next to the unit, a restore signal is sent. The magnet is adjustable with four height positions. A 1/4” high magnet spacer is also supplied to snap on to the base of the magnet. Alarms and restores can also be sent from external normally closed contacts wired to the transmitter’s external switch input terminals. The two screw terminals are for connection to one normally closed external contact or multiple normally closed external contacts wired in series. External contacts wire through an opening in the rear of the case.An internal jumper selects which switch input to use. Selections are: internal magnetic switch only, external switch only, or both external and internal switch.Approximately every two hours, the DXS-36AF will send a status signal to the receiver. The status signal updates the receiver to the transmitter’s current condition. By monitoring status signals, the receiver can determine if a transmitter has a low battery or has been removed from the system.Pressing the test button on the case sends a test signal that updates the receiver with the current state of the transmitter. When the test button is pressed, the transmit indicator lights. For two minutes after the test button is pressed, the indicator will light each time the unit sends a signal. The indicator light shines through the transmitter case.The transmitter contains a feature to detect unauthorized tampering. When the transmitter’s case is opened, a tamper signal is sent to the receiver.The transmitter is powered from one Type 2450 3-Volt lithium battery with an expected battery life of up to 5 years.OPENING CASE REMOVE BATTERY PROTECTION STRIPCOMPONENT LOCATIONS EXAMPLE INSTALLATIONSALARMFORCEAlarmForce Industries Inc.675 Garyray DriveToronto, ON M9L 1R2, CanadaTRANSMITTERMOUNTED ONDOOR JAMBMAGNETMOUNTEDON DOORMAGNET MOUNTEDON DOORTRANSMITTERMOUNTED ONWINDOW SILLMAGNET MOUNTEDON WINDOW FRAMESLIDING WINDOWLEFT OPENING DOORRIGHT OPENING DOORTRANSMITTERMOUNTED ONDOOR JAMBTRANSMITTERMOUNTED ONWINDOW FRAMEMAGNETMOUNTEDON WINDOWSASH STILEDOUBLE-HUNGWINDOWTYPE 2450BATTERYINPUTSELECTJUMPERTESTBUTTONEXTERNALSWITCHINPUT SIGNALINDICATORNOTE: SIGNAL INDICATORIS ENABLED FOR TWOMINUTES AFTER PRESSINGTHE TEST BUTTONTAMPERDETECTORMOUNTINGSCREWHOLESINTERNALMAGNETICSWITCHNOTE: BE SURE TO KEEPTAMPER DETECTOR AREACLEAR OF ANY WIRESPULL BATTERYSTRIP TO REMOVEBATTERYPROTECTION STRIPTWISTLIFTOPEN THE CASE TOP BY TWISTING A SMALL FLAT BLADE SCREWDRIVER OR COIN IN THE SLOT ON EITHER END OF THE TRANSMITTERDXS-36AFTRANSMITTERTRANSMITTERSCREWS ANDDOUBLE STICK TAPEMAGNETSCREWS ANDDOUBLE STICK TAPEADJUSTABLEMAGNETMAGNET CAN BE MOUNTED UP TO1/2" FROM LEFT SIDE OFTRANSMITTER1/2" GAP DISTANCEMAXIMUMSQUEEZE MAGNET TABS TOADJUST MAGNET HEIGHT (4 POSITIONS)MAGNETADJUSTMENTTAB (EACH SIDE)
TRANSMITTER MOUNTING ADJUSTING MAGNET HEIGHTOPTION JUMPER POSITIONS CONNECTING EXTERNAL CONTACTSPROGRAMMING RECEIVER CHANGING THE BATTERY• The radios are required to comply with IC Rules and Regulations. As such, they have limited transmitter power and therefore limited range.• A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings.• Infrequently used radio links should be tested regularly to protect against undetected interference or fault.• A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users.This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.• Reorient or relocate the receiving antenna• Increase the separation between the equipment and receiver• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected• Consult the dealer or an experienced radio/TV technician for helpAny changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device conforms to Industry Canada’s rules. Any changes to the equipment, not expressly approved by Linear LLC, could void the user’s authority to operate the equipment.Cet appareil est conforme aux règlements de l’Industrie Canada. Tout changement à l’équipement, sans le consentement exprès de Linear LLC, peut résulter à l’annulation de l’autorité confi ée à l’usager d’opérer cet équipement.WHEN THE SYSTEM INDICATES ALOW BATTERY FOR THE TRANSMITTER,REMOVE THE OLD BATTERY AND REPLACEIT WITH A FRESH TYPE 2450 3-VOLTCOIN CELL BATTERYBE SURE TO INSTALL THE BATTERYWITH THE PLUS SIDE UP !!! TEST THE SYSTEM AFTERCHANGING THE BATTERYWIRE EXTERNAL NORMALLY CLOSEDCONTACTS TO THE SCREW TERMINALSPLACE JUMPER ON PINS 2 & 3FOR EXTERNAL CONTACT ONLYREMOVE THE JUMPER TO USE BOTHINTERNAL AND EXTERNAL CONTACTSNOTE: THE INTERNAL AND EXTERNALCONTACTS ARE IN SERIES. BOTH NEEDTO BE CLOSED TO RESTORE THE TRANSMITTERREMOVE SEALING PLUGAND ROUTE WIRESTHROUGH SLOT INBOTTOM OF CASEWIRE MULTIPLE EXTERNALCONTACTS IN SERIESJUMPER ON 1 & 2 SELECTSINTERNAL MAGNETIC SWITCH INTERNAL EXTERNAL BOTHJUMPER ON 2 & 3 SELECTSEXTERNAL SWITCH TERMINALS NO JUMPER SELECTS BOTH THEINTERNAL MAGNETIC SWITCH ANDTHE EXTERNAL SWITCH TERMINALS 1. PLACE RECEIVER INTO PROGRAM OR "LEARN" MODE2. PRESS THE TRANSMITTER'S TEST BUTTON3. ACTIVATE TRANSMITTER BY OPENING DOOR OR WINDOW4. VERIFY THAT THE RECEIVER ACCEPTED THE SIGNAL5. REPLACE TRANSMITTER COVER WHEN FINISHEDOPEN DOOR, THE TRANSMITINDICATOR SHOULD LIGHTNOTE: THE TRANSMIT INDICATOR WILL ONLY LIGHT DURING TRANSMISSIONS FOR TWO MINUTES AFTER PRESSING THE TEST BUTTONNOTE: THE CASE MUST BE CLOSEDTO LEARN INTO THE RECEIVER(IT WON'T LEARN IN IF TRANSMITTERIS IN TAMPER MODE)ADJUST MAGNETHEIGHT UNTILCASE LEVELSARE ABOUT EQUALTRANSMITTERCASE BOTTOMMAGNETTHE SNAP-ON MAGNET SPACERCAN BE USED TO ADD 1/4" HEIGHTTO THE MAGNET (SPACERS CAN ALSOBE SNAPPED TOGETHER FOR MORE LIFT)ATTACH TRANSMITTER AND MAGNETUSING THE SCREWS OR THEDOUBLE-STICK TAPE PROVIDEDNOTE: ATTACHING THE TRANSMITTER WITH DOUBLE-STICKTAPE IS NOT ALLOWED IN UL INSTALLATIONSPRINTER’S INSTRUCTIONS:INSTR,INSTL,DXS-36AF - LINEAR P/N: 232812 X4 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” X 11.000” - SCALE: 1-1 - SIDE 2 OF 2Copyright © 2012 232812 X4

Navigation menu