Nortek Security and Control 00118 Security/Remote Control Transmitter User Manual 235686A GD00Z 1 Instructions IRIS indd

Nortek Security & Control LLC Security/Remote Control Transmitter 235686A GD00Z 1 Instructions IRIS indd

User Manual

GD00Z-1GARAGE DOOR OPENERREMOTE COMMANDCONTROLLERwith TILT SENSORInstallation Instructions1. PRODUCT DESCRIPTIONThe Model GD00Z-1 is a garage door opener Remote Command Controller with built-in Z-Wave® interoperable two-way RF mesh networking technology designed for use with Lowe’s Iris® hub. A garage door opener connected to the Controller can be remotely activated using the Iris web interface or Iris mobile applications.The GD00Z-1 Controller connects to the garage door opener’s pushbutton wall console terminals and communicates with the Iris hub using Z-Wave radio signals. A wireless tilt sensor mounts on the garage door and reports the door’s position to the Controller. When the Controller receives a command from the Iris hub, it will open or close the garage door.Anytime the garage door opener is activated remotely by the Controller, a warning indicator fl ashes and a beeper sounds for fi ve seconds before the door begins to move.If, due to an obstruction or other cause, the door does not completely open or close when it is activated remotely, the Controller will pause for 30 seconds. After the delay, a second remote activation can be attempted. If the door does not complete its motion on the second attempt, the Controller will suspend operation until the door is operated locally with the opener’s pushbutton wall console.The Controller is powered by a plug-in power supply. The Model TILT 345 tilt sensor is powered by a 2032 lithium battery. If the tilt sensor battery is low, it will be reported to the Iris hub by the Controller. A link button and status light are provided on the Controller for adding or removing the device with the Iris hub.Four screws and anchors are provided for mounting the Controller. An adjustable controller mounting bracket with hardware is supplied for installing the unit onto the door opener’s hanging hardware. The wireless tilt sensor mounts with double sided tape or the two screws supplied.2. SAFETY NOTES3. PRODUCT FEATURES 4. TILT SENSOR INSTALLATION AND BATTERY 5. PAIRING WITH IRISUSA & Canada (800) 421-1587 & (800) 392-0123(760) 438-7000 - Toll Free FAX (800) 468-1340www.linearcorp.comPRINTER’S INSTRUCTIONS:INSTR,INSTL,GD00Z-1 - LINEAR P/N: 235686 X21 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 1 OF 2 WARNING This operator system is equipped with an unattended operation feature. This door could move unexpectedly. NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR! WARNING This system can be installed on sectional type (roll up) doors only per (UL-325). DO NOT INSTALL ON ONE-PIECE DOORS! WARNING Do not install the Remote Command Controller on garage door operators manufactured prior to 1993 (models without an operational safety beam entrapment detection system). WARNING The Remote Command Controller must be mounted in the garage, in sight of the garage door, where the visual and audible movement warning indicators can be clearly seen and heard.Z-Wave® is a registered trademark of Sigma Designs Inc. and/or its subsidiaries.CONTROLLERPOWERINPUTJACKWARNINGLIGHTLINKBUTTONCONTROLLERCONNECTIONWIRESDOUBLE SIDEDMOUNTING TAPE,SCREWS AND ANCHORSPOWERSUPPLYTILTSENSORSTATUSINDICATORADJUSTABLEMOUNTINGBRACKET(OPTIONAL)POWERSUPPLYRETAININGBRACKETPARING THE CONTROLLER REMOVING THE CONTROLLERTO PAIR WITHTHE IRIS HUBTO REMOVE FROMTHE IRIS HUBFROM THE IRIS WEB SITE, CLICK"DEVICES", THEN CLICK THE "ADD DEVICES" BUTTONFOLLOW THE ON-SCREENINSTRUCTIONS TO PAIR THECONTROLLER WITH THE HUBSELECT GARAGE DOORCONTROLLER FROM THE LIST123124FROM THE IRIS WEB SITE,CLICK "DEVICES"ON THE GARAGE DOORCONTROLLER DEVICE CLICK"MANAGE", THEN CLICK "REMOVE"FOLLOW THE ON-SCREENINSTRUCTIONS TO UN-PAIR THECONTROLLER WITH THE HUB3WALLOUTLETPOWERSUPPLY POWERINPUTJACKLINKBUTTONCONTROLLERWHEN INSTRUCTED, PRESSTHE LINK BUTTON ON THECONTROLLER4WHEN INSTRUCTED, PRESSTHE LINK BUTTON ON THECONTROLLERwww.lowes.com/irisCR2032PLUS SIDE UP !!!IRIS WILL NOTIFY YOU WHENTHE BATTERY IS LOW,REPLACE THE BATTERY WITHA TYPE CR2032 COIN CELLINSERT THEBATTERYINTO THETRANSMITTERTO OPEN THE CASE, TWISTA SMALL SCREWDRIVERIN CASE SLOT SLOTATTACH MOUNTING PLATETO TOP PANEL OF THE DOOR USE DOUBLE SIDED TAPE ORTHE TWO MOUNTING SCREWS SUPPLIED(DRILL 1/16" PILOT HOLES IF REQUIRED)POST ONBOTTOM"UP"ARROWSSNAP SENSOR ONTOTHE MOUNTING PLATETO ACTIVATE THE TILT SENSOR, REMOVE THE BATTERY PROTECTION PULL STRIPARROWS ON PLATE& SENSOR POINT UP
6. CONTROLLER MOUNTING 7. CONTROLLER CONNECTIONS 8. SYSTEM OPERATION9. OPERATION NOTES1. The warning light will fl ash and the warning beeper will sound fi ve seconds before the door opener is activated. STAY CLEAR OF THE DOOR, AND DOOR OPENER. THEY ARE ABOUT TO MOVE!2. If the door does not completely open or close after remote activation, the Controller will allow user to try to operate the door one more time. If the second attempt fails, the Controller will go into lock-out mode and blink the status indicator. See Note #3.3. If the status indicator is blinking, the Controller is in lock-out mode and will not accept remote commands. Activate the door from the pushbutton wall console then check that the status indicator stops blinking.10. TROUBLESHOOTINGPROBLEM POSSIBLE CAUSE CORRECTIVE ACTIONThe Controller does not fl ash or beep when activated.No power to the Controller.1. Make sure the power supply is plugged in securely to a live outlet.2. Make sure the power cord is plugged in securely to the Controller.The Controller fl ashes and beeps when activated but the door does not move.Obstruction blocking the door or incorrect wiring.1. Make sure that there are no obstacles preventing the door from moving.2. Make sure that the Controller’s connection wires are connected to the proper terminals on the garage door opener. Trace the wires from the garage door opener’s pushbutton wall console to the door opener. This is where the Controller’s connection wires should be connected to.Garage door opens or closes, but the status does not change on the Iris website or mobile app.The tilt sensor signal is not being received by the Controller.1. Make sure the tilt sensor is mounted correctly on the garage door, with the arrow pointing up.2. Make sure the battery pull tab has been removed from the tilt sensor.3. Replace the battery in the tilt sensor.LINEAR LIMITED RETAIL WARRANTYLinear LLC (the Company) warrants to the original purchaser that products delivered hereunder will be free of defects in materials and workmanship for a period of one (1) year from the date of purchase.The Company within said period shall at its option, either repair or replace free of charge, any product or part thereof found, upon the Company’s inspection, to be so defective, and will return the repaired or replaced product to the purchaser at Company’s expense.All products returned for warranty service require a Return Product Authorization Number (RPA#). For warranty service, shipping instructions, and an RPA#, contact Linear Technical Services at 1-855-546-3351. Devices must be sent to the Company at owner’s expense and be accompanied with statement of defect and proof of purchase.This warranty is conditioned on the following:1. The Company must be notifi ed within one year of purchase and have been given the opportunity of inspection by return of any alleged defective product free and clear of all liens and encumbrances to the Company or its distributor; and2. The product must not have been abused, misused or improperly maintained and/or repaired during such period; and3. Such defect has not been caused by corrosion or exposure to other than ordinary wear and tear.THE COMPANY MAKES NO OTHER WARRANTY OR REPRESENTATION OF ANY KIND WHATSOEVER INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.The Company’s maximum liability hereunder is limited to the purchased price of the product. In no event shall the Company be liable for any consequential, indirect, incidental or special damages of any nature arising from the sale or use of the product, whether based in contract, tort, strict liability or otherwise.Note: Some states do not allow limitations on incidental or consequential damages or how long an implied warranty lasts, so that the above limitations may not fully apply. This warranty gives specifi c legal rights and you may also have other rights which may vary from state to state.This device complies with FCC Part 15 and Canada Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.PRINTER’S INSTRUCTIONS:INSTR,INSTL,GD00Z-1 - LINEAR P/N: 235686 X21 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 2 OF 2THE CONTROLLER TYPICALLYMOUNTS ON THE CEILINGNEAR THE OPENER ANDTHE POWER OUTLETTILT SENSORMOUNTED ONTHE TOP PANELOF THE DOORTHE CONTROLLER CAN ALSO BE ATTACHED TO THE OPENER'SHARDWARE USING THE ADJUSTABLE MOUNTING BRACKETTHE CONTROLER'S WARNINGLAMP MUST BE VISIBLE INALL DOOR POSITIONS3/16" HOLESFOR ANCHORSTHE OPTIONAL ADJUSTABLEMOUNTING BRACKET FITS3 WAYS ON THE CONTROLLERTHE BRACKET SNAPS ONTOINDENTS ON EITHER SIDE ORON THE END OF THE CONTROLLERSECUREBRACKETWITH SCREWUSE THE FOUR SCREWSAND ANCHORS TO MOUNTTHE CONTROLLER ABOVETHE OPENERINDENTINDENTUSE THE BOLTS AND NUTSSUPPLIED TO ATTACH THEBRACKET TO A SECURESTRUCTUREBE SURE THE CONTROLLERIS CLEAR OF ALL MOVINGPARTS OF THE GARAGE DOORINDENTPUSHBUTTONPUSHBUTTONGARAGEDOOROPENERCONNECT THE CONTROLLER CONNECTIONWIRES TO THE PUSHBUTTON WALLCONSOLE TERMINALS ON THE GARAGEDOOR OPENER. THE TERMINALS MAY BENAMED "PWC", "WC", "PB", "PUSHBUTTON",OR "RED AND WHITE". TERMINAL NAMESAND LOCATIONS VARY BY MODEL.DO NOT DISCONNECTANY WIRES CURRENTLYCONNECTED TO THEGARAGE DOOR OPENER !!!1PLUG THE POWER SUPPLYINTO 115 VAC OUTLETAND SECURE IT WITHTHE RETAINING BRACKETBE SURE WIRES ARECLEAR OF ALL MOVINGPARTS OF THE GARAGEDOOR AND OPENER3EITHER WIRECAN CONNECTTO EITHERTERMINALPLUG THE POWER CORDINTO THE POWER INPUTJACK ON THE CONTROLLER2FLASHFLASHFLASHBEEPBEEPBEEPUSE THE IRIS WEB SITE AND MOBILEAPPS TO CONTROL YOUR GARAGEDOOR, VIEW STATUS, AND SETCUSTOM RULESTHE CONTROLLER WILL ACTIVATETHE DOOR OPENER AND OPENOR CLOSE THE DOORSTAY CLEAROF THE DOOR !!!1THE CONTROLLER WILL BEEP ANDFLASH FOR FIVE SECONDS BEFORETHE DOOR MOVES234THE IRIS WEB PAGE OR MOBILEAPP WILL SHOW THE NEW STATUSOF THE DOOR AFTER THE DOORCOMPLETES ITS CYCLENOTICE TO USERS IN CALIFORNIA - CR COIN CELL LITHIUM BATTERY INFORMATION: THIS PRODUCT CONTAINS A CR COIN CELL LITHIUM BATTERY WHICH CONTAINS PERCHLORATE MATERIAL - SPECIAL HANDLING MAY APPLY - SEE www.dtsc.ca.gov/hazardouswaste/perchlorateKEEP AWAY FROM SMALL CHILDREN. IF BATTERY IS SWALLOWED, PROMPTLY SEE A DOCTOR. DO NOT TRY TO RECHARGE THIS BATTERY. DISPOSAL OF USED BATTERIES MUST BE MADE IN ACCORDANCE WITH THE WASTE RECOVERY AND RECYCLING REGULATIONS IN YOUR AREA.Changes or modifi cations not expressly approved by the manufacturer could void the user’s authority to operate the equipment.Les changements ou modifi cations non approuvés expressément par la partie responsable de la conformité pourrait annuler l’autorité de l’utilisateur à faire fonctionner l’équipement. Copyright © 2014 Linear LLC 235686 X21

Navigation menu