Nortek Security and Control GTO Access GDKPD318B Wireless keypad control User Manual

GTO Access Systems, LLC Wireless keypad control

User Manual

Copyright © GTO Access Systems 2015 10007727 CSKPL DIGITAL KEYPAD TRANSMITTER Installation InstructionsDESCRIPTIONThis Digital Keypad is designed for use with automatic garage door operators. The radio format provides unparalleled security with more than a million different codes.To activate the door operator, the user enters their unique 1 to 6 digit long code on the unit’s keypad and presses the START/STOP button. For up to 30 seconds after the last activation, the keypad can be re-triggered by simply pressing the START/STOP button again. This allows the user to stop or reverse the opener quickly, without having to re-enter their code.The keypad has built-in lighting for use at night or in dark areas. The clear silicone keys are backlit with a pleasing blue glow. By pressing the START/STOP button rst, before entering their code, the user can light up the keypad. Pressing the START/STOP button twice at any time will light up the keypad.The keypad lockout timer will disable the keypad after 10 activations. The keypad must remain idle for 30 seconds before new attempts.The garage door operator contains a built-in receiver that is programmed by sending a signal from the user’s transmitters. This stores the transmitter’s code into the receiver’s memory. The receiver will retain its memory even without power and will only activate from these “memorized” transmitters. Each keypad code can be considered a different transmitter.KEYPAD COMPONENTS KEYPAD FEATURESKEYPAD OPERATION CHANGING BATTERIES LIMITED WARRANTY FCC STATEMENTPROGRAMMING OPERATOR WALL MOUNTINGPRINTER’S INSTRUCTIONS:INSTR,INSTL,MDTK,PVT LBL - GTO P/N: 10007727 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1www.mightymule.comADDING A KEYPAD CODE1PRESS THE OPERATOR'S LEARN BUTTON FOR 1 SECOND AND RELEASE. THE OPERATOR SHOULD BEEP AND THE LIGHT SHOULD BLINK ONCE. THE RED LED WILL REMAIN LIT (LEARN REMOTE MODE).2WHILE THE RED LED IS ON, ENTER A 1-6 DIGIT KEYPAD CODE THEN PRESS AND HOLD THE KEYPAD'S START/STOP KEY UNTIL THE OPERATOR BEEPS AND THE LIGHT BLINKS ONCE.3REPEAT STEPS 1 & 2 FOR ANY ADDITIONAL KEYPAD CODESWXYGHIDEFABCJKLMNOPRSTUVSCREWPLUGSSCREWANCHORS MOUNTINGSCREWSKEYPADHINGED COVERPROTECTS THE KEYPADSOFT BLUE LIGHTSILLUMINATE THE KEYSFOR NIGHTTIME USESTART/STOP BUTTON STAYS ACTIVE FOR30 SECONDS AFTER A CODE IS USED SO THE OPENER CAN BE STOPPED OR REVERSEDNOTE: FOR SECURITY, THE KEYPAD WILL SHUTDOWNAFTER 10 CODE ENTRIES UNTIL IT IS IDLE FOR 30 SECONDSTEN KEYS ENTERING 1-6 KEYPAD CODESUSING NUMBERS OR LETTERS MOUNT THE KEYPAD INCLEAR VIEW OF THE DOORWITH THE TWO SCREWS SUPPLIED USE THE SCREWS ANCHORS SUPPLIEDIF REQUIREDSCREWS ANCHORSPUSH IN THETWO SCREWCOVER TO HIDETHE SCREWSDAYTIME OPERATIONSTARTSTOPSTARTSTOPSTARTSTOP12PRESS START/STOP (LIGHTS KEYPAD) 123NIGHTTIME OPERATIONPRESS THE LIGHT ( ) BUTTON TO TURN THE OPERATOR’S LIGHT ON/OFF(KEYPAD MUST HAVE AT LEAST ONE CODE PROGRAMMED INTO THE OPERATOR)1LIGHT OPERATION1-6 DIGIT KEYPAD CODE THATWAS ENTERED INTO OPENERENTER THE KEYPAD CODEPRESS START/STOPENTER THE KEYPAD CODEPRESS START/STOP 1-6 DIGIT KEYPAD CODE THATWAS ENTERED INTO OPENERNOTE: TO STOP OR REVERSE THE OPERATOR, THE START/STOP BUTTON CAN BE PRESSED AGAIN FOR UP TO 30 SECONDS WITHOUT RE-ENTERING THE CODE. 1342REMOVE THE TWOSCREWS AND SLIDETHE BATTERY COVER OFF REMOVE THE LOW VOLTAGEBATTERIES AND DISPOSE OF THEM PROPERLYINSTALL 3 FRESHAAA BATERIES BE SURE THE SILICONE GASKETIS IN PLACE REPLACE THEBATTERY COVERAND RE-INSTALL THE TWO SCREWS This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide rea-sonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.CAUTION!Any changes or modications not expressly approved by the party responsible for compli-ance could void the user’s authority to operate the equipment.This product is warranted to the original consumer against defects in material and workmanship for the periods mentioned above. GTO Access Systems will repair, or at its option, replace, any device that it nds requires service under this warranty. This warranty does not apply to damage to the product from negligence, abuse, abnormal usage, misuse, accidents, normal wear or tear or due to failure to follow Seller’s instructions, or arising from improper installation, storage or maintenance. In no event will GTO Access Systems be responsible for incidental, compensatory, punitive, consequential, indirect, special or other damages. The remedies provided by this warranty are exclusive. Some states do not allow the exclusion or limitation of incidental and consequential damages, so the above limitation or exclusion may not apply to you. Any warranties implied by law are limited to the time periods set forth above. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specic legal rights, and you may also have other rights which vary from state to state.For warranty service, contact GTO Access Systems at 800-543-1236. In order to be protected by this warranty, save your proof of purchase should repair be required.IMPORTANT!Radio controls provide a reliable communications link and ll an important need in portable wireless signaling. However, there are some limitations which must be observed.• For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range.• A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies.• Changes or modications to the device may void FCC compliance.• Infrequently used radio links should be tested regularly to protect against undetected interference or fault.• A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users.

Navigation menu