Nextivity orporated Q34-45121325CU Provider-Specific Consumer Signal Booster User Manual

Nextivity Incorporated Provider-Specific Consumer Signal Booster

User Manual

If you need help, visit: www.cel-.com/support.Safety Precautions•Use Cel-Fi indoors. It should not be used outdoors.•These products are designed to be used with a direct plug-in power supply unit that shipped with the Network Unit. When installing the equipment, all the requirements of the manufacturer and the referenced standards must be met.•There are no user serviceable parts inside.•CAUTION: Changes or modications to this product not expressly approved by Nextivity may void your right to operate the equipment.WarrantyNextivity  Inc  provides  a  limited  warranty  for  its products.  For  details,  please  refer  to  http://cel-.com/warranty.Limitation of LiabilityIn  no  event  shall  Nextivity,  nor  its  directors, employees,  agents,  suppliers  or  End  Users, be  liable  under  contract,  tort,  strict  liability, negligence or any other legal or equitable theory with respect to the Products or any other subject matter of this Agreement (i) for any lost prots, cost  of  procurement  of  substitute  goods  or services, or special, indirect, incidental, punitive, or consequential  damages  of  any  kind  whatsoever or (ii) for any direct damages in excess of (in the aggregate) the fees actually received by Nextivity from  End  User  with  respect  to  the  Products actually purchased and paid for.See  cel-.com  for  list  of  patents  covering  this product. TrademarkCel-Fi,  IntelliBoost,  and  Nextivity  logo  are trademarks of Nextivity, Inc.This is a CONSUMER device.BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent.  Most  wireless  providers  consent  to  the use  of  signal  boosters.  Some  providers  may  not consent to the use of this device on their network. If you are unsure, contact your provider.You  MUST  operate  this  device  with  approved antennas  and  cables  as  specied  by  the manufacturer.Antennas  MUST  be  installed  at  least  20  cm  (8 inches) from any person.You  MUST  cease  operating  this  device immediately  if  requested by  the  FCC,  Innovation, Science and Economic Development Canada or a licensed wireless service provider.WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device.FCC Statement (Applicable in the USA only) When  used  with  any  mobile  device  utilizing  the 1710-1755  MHz  band,  the  FCC  limits  booster equipment  placement  to  a  maximum  of  10 meters  above  ground  level.  Installation  of  this equipment  which  does  not  comply  with  federal requirements  may  subject  the  owner  to  FCC enforcement action.This  device  complies  with  part  15  of  the  FCC Rules.  Operation  is  subject  to  the  following  two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference  received,  including  interference  that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital de-vice, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protec-tion against harmful interference in a residential If you need help, visit: www.cel-.com/support.Safety Precautions•Use Cel-Fi indoors. It should not be used outdoors.•These products are designed to be used with a direct plug-in power supply unit that shipped with the Network Unit. When installing the equipment, all the requirements of the manufacturer and the referenced standards must be met.•There are no user serviceable parts inside.•CAUTION: Changes or modications to this product not expressly approved by Nextivity may void your right to operate the equipment.WarrantyNextivity  Inc  provides  a  limited  warranty  for  its products.  For  details,  please  refer  to  http://cel-.com/warranty.Limitation of LiabilityIn  no  event  shall  Nextivity,  nor  its  directors, employees,  agents,  suppliers  or  End  Users, be  liable  under  contract,  tort,  strict  liability, negligence or any other legal or equitable theory with respect to the Products or any other subject matter of this Agreement (i) for any lost prots, cost  of  procurement  of  substitute  goods  or services, or special, indirect, incidental, punitive, or consequential  damages  of  any  kind  whatsoever or (ii) for any direct damages in excess of (in the aggregate) the fees actually received by Nextivity from  End  User  with  respect  to  the  Products actually purchased and paid for.See  cel-.com  for  list  of  patents  covering  this product. TrademarkCel-Fi,  IntelliBoost,  and  Nextivity  logo  are trademarks of Nextivity, Inc.This is a CONSUMER device.BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent.  Most  wireless  providers  consent  to  the use  of  signal  boosters.  Some  providers  may  not consent to the use of this device on their network. If you are unsure, contact your provider.You  MUST  operate  this  device  with  approved antennas  and  cables  as  specied  by  the manufacturer.Antennas  MUST  be  installed  at  least  20  cm  (8 inches) from any person.You  MUST  cease  operating  this  device immediately  if  requested by  the  FCC,  Innovation, Science and Economic Development Canada or a licensed wireless service provider.WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device.FCC Statement (Applicable in the USA only) When  used  with  any  mobile  device  utilizing  the 1710-1755  MHz  band,  the  FCC  limits  booster equipment  placement  to  a  maximum  of  10 meters  above  ground  level.  Installation  of  this equipment  which  does  not  comply  with  federal requirements  may  subject  the  owner  to  FCC enforcement action.This  device  complies  with  part  15  of  the  FCC Rules.  Operation  is  subject  to  the  following  two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference  received,  including  interference  that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital de-vice, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protec-tion against harmful interference in a residential PRODUCT INFORMATIONCel-Fi™ QUATRA Smart Cellular CoveragePRODUCT INFORMATIONCel-Fi™ QUATRA Smart Cellular CoverageSTOP!!! Do not call your service provideruntil you have read the Quick Start Guide.STOP!!! Do not call your service provideruntil you have read the Quick Start Guide.
Legal_QuatraLR-Eng-2-4-5-12-13 Legal_QuatraLR-Eng-2-4-5-12-13installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equip-ment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•Consult the dealer or an experienced radio/TV technician for helpISED STATEMENTThis is a CONSUMER device.BEFORE USE, meet all requirements  set out in CPC-2-1-05.This device may operate in a xed location only, for in-building use.In  order  to  comply  with  ISED  RF  Exposure requirements,  this  device  must  be  installed  to provide at least 20 cm separation from the human body at all times.[FRENCH:  An  de  se  conformer  aux  exigences d’exposition  RF  de  ISED,  cet  appareil  doit  être installé pour fournir au moins 20 cm de séparation du corps humain en tout temps.] The  Manufacturer’s  rated  output  power  of  this equipment  is  for  single  carrier  operation.  For situations  when  multiple  carrier  signals  are present,  the  rating  would  have  to  be  reduced  by 3.5  dB,  especially  where  the  output  signal  is  re-radiated  and  can  cause  interference  to  adjacent band  users.  This  power  reduction  is  to  be  by means of input power or gain reduction and not by an attenuator at the output of the device.[FRENCH:  La  puissance  de  sortie  nominale indiquée par le fabricant pour cet appareil concerne son  fonctionnement  avec  porteuse  unique.  Pour des  appareils  avec  porteuses  multiples,  on  doit réduire  la  valeur  nominale  de  3,5dB,  surtout  si  le signal de sortie est retransmis et qu’il peut causer du brouillage aux utilisateurs de bandes adjacentes. Une  telle  réduction  doit  porter  sur  la  puissance d’entrée  ou  sur  le  gain,  et  ne  doit  pas  se  faire  au moyen  d’un  atténuateur  raccordé  à  la  sortie  du dispositif.]This device complies with Industry Canada license-exempt  RSS  standard(s).  Operation  is  subject  to the following two conditions: (1) this device may not  cause  interference,  and  (2)  this  device  must accept any interference, including interference that may cause undesired operation of the device.[FRENCH:  Le  présent  appareil  est  conforme aux  CNR  d’Industrie  Canada  applicables  aux appareils  radio  exempts  de  licence.  L’exploitation est  autorisée  aux  deux  conditions  suivantes:  (1) l’appareil ne doit  pas produire de  brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique  subi,  même  si  le  brouillage  est susceptible d’en compromettre le fonctionnement.]Gain 100dBBandwidth 75MhzInput and Output Impedances50 ohmOutput PowerUplink 22dBm per bandDownlink 16dBm per bandCompliance ContactIn the event of regulatory compliance issue, please contact Nextivity Inc. directly. Contact information is available at www.nextivityinc.com.PatentsThis  product  is  covered  by  Nextivity,  Inc.,  US patents  and  patents  pending.  Please  refer  to cel-.com for details.CopyrightCopyright  ©  2017  by  Nextivity,  Inc.  All  rights reserved.  Reproduction  or  media  conversion  by any means is protected by copyright and may only occur  with  prior  written  permission  of  Nextivity. Designed by Nextivity in California.installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:•  Reorient or relocate the receiving antenna.•Increase the separation between the equip-ment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•Consult the dealer or an experienced radio/TV technician for helpISED STATEMENTThis is a CONSUMER device.BEFORE USE, meet all requirements  set out in CPC-2-1-05.This device may operate in a xed location only, for in-building use.In  order  to  comply  with  ISED  RF  Exposure requirements,  this  device  must  be  installed  to provide at least 20 cm separation from the human body at all times.[FRENCH:  An  de  se  conformer  aux  exigences d’exposition  RF  de  ISED,  cet  appareil  doit  être installé pour fournir au moins 20 cm de séparation du corps humain en tout temps.] The  Manufacturer’s  rated  output  power  of  this equipment  is  for  single  carrier  operation.  For situations  when  multiple  carrier  signals  are present,  the  rating  would  have  to  be  reduced  by 3.5  dB,  especially  where  the  output  signal  is  re-radiated  and  can  cause  interference  to  adjacent band  users.  This  power  reduction  is  to  be  by means of input power or gain reduction and not by an attenuator at the output of the device.[FRENCH:  La  puissance  de  sortie  nominale indiquée par le fabricant pour cet appareil concerne son  fonctionnement  avec  porteuse  unique.  Pour des  appareils  avec  porteuses  multiples,  on  doit réduire  la  valeur  nominale  de  3,5dB,  surtout  si  le signal de sortie est retransmis et qu’il peut causer du brouillage aux utilisateurs de bandes adjacentes. Une  telle  réduction  doit  porter  sur  la  puissance d’entrée  ou  sur  le  gain,  et  ne  doit  pas  se  faire  au moyen  d’un  atténuateur  raccordé  à  la  sortie  du dispositif.]This device complies with Industry Canada license-exempt  RSS  standard(s).  Operation  is  subject  to the following two conditions: (1) this device may not  cause  interference,  and  (2)  this  device  must accept any interference, including interference that may cause undesired operation of the device.[FRENCH:  Le  présent  appareil  est  conforme aux  CNR  d’Industrie  Canada  applicables  aux appareils  radio  exempts  de  licence.  L’exploitation est  autorisée  aux  deux  conditions  suivantes:  (1) l’appareil ne doit  pas produire de  brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique  subi,  même  si  le  brouillage  est susceptible d’en compromettre le fonctionnement.]Gain 100dBBandwidth 75MhzInput and Output Impedances50 ohmOutput PowerUplink 22dBm per bandDownlink 16dBm per bandCompliance ContactIn the event of regulatory compliance issue, please contact Nextivity Inc. directly. Contact information is available at www.nextivityinc.com.PatentsThis  product  is  covered  by  Nextivity,  Inc.,  US patents  and  patents  pending.  Please  refer  to cel-.com for details.CopyrightCopyright  ©  2017  by  Nextivity,  Inc.  All  rights reserved.  Reproduction  or  media  conversion  by any means is protected by copyright and may only occur  with  prior  written  permission  of  Nextivity. Designed by Nextivity in California.Bureau in EuropeUnit 6, Basepoint Business CentreRivermead Drive, WestleaSwindon SN5 7EXU.S. Headquarters: Nextivity Inc.16550 West Bernardo Drive  Bldg. 5, Suite 550 San Diego, CA 92127, USA+1 858.485.9442 tel+1 858.485.9445 faxwww.cel-.comNextivity Singapore Pte. Ltd.2 Changi Business Park Avenue 1Level 2 – Suite 16,486015 SingaporeBureau in EuropeUnit 6, Basepoint Business CentreRivermead Drive, WestleaSwindon SN5 7EXU.S. Headquarters: Nextivity Inc.16550 West Bernardo Drive  Bldg. 5, Suite 550 San Diego, CA 92127, USA+1 858.485.9442 tel+1 858.485.9445 faxwww.cel-.comNextivity Singapore Pte. Ltd.2 Changi Business Park Avenue 1Level 2 – Suite 16,486015 Singapore

Navigation menu