Nextivity orporated CELFI-RS240CU Cel-Fi Residential System User Manual 420N003 001 001 10R51

Nextivity Incorporated Cel-Fi Residential System 420N003 001 001 10R51

420N003-001-001-10R51

Congratulations on your new indoor signal solution. This Cel-Fi system is designed to provide you with signicant improvements in coverage as well as 3G data rates. Setting up the system is extremely simple and consists of placing and plugging in two components; a Window Unit and a Coverage Unit.By spending just a few minutes using the instructions in this guide, you can optimize the installation and get the very most from your new Cel-Fi System.If you have any trouble during setup, please use the trouble shooting steps included in this guide.In the package you will nd: Window UnitCoverage Unit Two power adapters.CEL-FIRS 2 Quick Start GuideStep 1 Find the spot with the best 3G coverage:The rst step in setting up your Cel-Fi system is to nd the spot in your home or oce that has the best 3G coverage. This is typically by a window, and if you are in a multi-story building, upstairs windows are usually better than downstairs windows.Step 2 Plug in the Window Unit:Take the Window Unit and one power supply out of the box (both power supplies are the same, so grab either one). Plug the Window Unit in, and check to make sure that you can see at least 1 “Bar” on the display in the center of the device. If you do not see at least 1 bar, try a dierent location.NEED HELP?Visit us at www.celfihelp.com for an installation video and other helpful information regarding installation and trouble shooting.WINDOW UNITWINDOW UNITCOVE R AGE UNIT
COVERAGE UNITCEL-FIRS 2 Trouble ShootingTOO CLOSEA zero on the numeric display indicates that the “Coverage Unit” needs to be moved farther away from the “Window Unit”.GOODThis green icon indicates that the “Coverage Unit” is functioning normally.TOO FARThis red icon indicates that the “Coverage Unit” needs to be moved closer to the “Window Unit”.Step 3Optimize the Window Unit PlacementThe number of bars you can see on the Window Unit make a significant difference in the operation of the Cel-Fi system. Try moving the Window Unit to a couple of different spots to see if you can get better signal; the more bars the better.Step 5Optimize The Coverage Unit PlacementThe farther away you place the coverage unit from the Window unit the better the coverage in your home, so put the Coverage Unit as far away from the Window Unit as possible. The number shown on the side of the display gives you an indication as to the quality of the placement. Test two or three locations and for best results; try and get a 7, 8 or 9 on the display.IndicatorNo lights on “Window Unit” display.Status indicator is flashing green for more than a minute.Status indicator is flashing red.Status indicator is on solid red.No segment lit on signal display and status indicator on solid green.ProblemThere is no power.The “Window Unit” unit is attempting to complete regulatory compliance.Error Code on ”Coverage Unit”.Hardware Error.Not receiving cell signal.Try This1. Is the unit plugged in?2. Is there power at the outlet?3. Try exchanging the power supplies with the “Coverage Unit” to see if the power supply is defective.1. Wait for the status indicator to stop flashing, this could take several minutes.1. See the “Coverage Unit” to determine what error code is being displayed.1. Try resetting the “Window Unit” by unplugging it and then plugging it back in. 2. If problem persists return system for service/replacement.1. Try moving the “Window Unit” to another room or area where you have more coverage. (Use your cell phone to find the best 3G coverage).IndicatorE1E3E4ProblemNo Signal on “Window Unit”.”Coverage Unit” is overheating.“Window Unit” is overheating.Try ThisTry moving the “Window Unit” to another room or area where you have coverage. (Use your cell phone to find the best 3G coverage).Make sure that the vents on the unit are not blocked. Move the unit to a cooler area. The system will start working normally when it cools down.Indicator No lights on ”Coverage Unit” display.7 segment display is cycling for more than a minute.7 segment display shows a value of 0.Red “Too Far” Indicator.Red Status Indicator.ProblemThere is no power.The ”Coverage Unit” is taking longer than normal to make a link.The ”Coverage Unit” is “Too Close” to the “Window Unit”.The ”Coverage Unit” is “Too Far” from the “Window Unit”Hardware Error.Try This1. Is the unit plugged in?2. Is there power at the outlet?3. Try exchanging the power supplies with the “Window Unit” to see if thepower supply is defective.1. Wait for the display to stop cycling, this could take several minutes2. Move away from WiFi devices.1. Move the ”Coverage Unit” further away from the “Window Unit”.1. Move the ”Coverage Unit” closer to the “Window Unit”.1. Try resetting the ”Coverage Unit” by unplugging it and then plugging it back in. 2. If problem persists return system for service.WINDOW UNITCOVERAGE UNITERRORMESSAGESW I N D O W UNITStep 4Place the Coverage UnitMove to a location in your home where you need to have improved coverage. Plug the Coverage unit in and wait until the numeric display stops cycling, this could take several minutes. At this point you should see a green icon indicating that the unit is working properly. It is possible to place the Coverage Unit so far away that it cannot communicate with the Window Unit. If this happens, a red icon will illuminate indicating that you need to move the Coverage Unit closer to the Window unit.420N003-001-001-10R51

Navigation menu