Nextivity orporated CELFI-RS225CUA AT&T; Provider Specific Consumer Signal Booster User Manual

Nextivity Incorporated AT&T; Provider Specific Consumer Signal Booster Users Manual

Users Manual

Step 1Find the spot with the best 3G coverage:The rst step in setting up your Cel-Fi system is to nd the spot in your home or oce that has the best 3G coverage by using your phone (3G icon must be displayed). This is typically by a window, and if you are in a multi-story building, upstairs windows are usually better than downstairs windows.Step 2Plug in the Window Unit:Take the Window Unit and one power supply out of the box (both power supplies are identical, so you can use either one). Plug the Window Unit into an easily accessible outlet. Check to make sure that you can see at least 1 “Bar” on the display in the center of the device. If you do not see at least 1 bar, try a dierent location.CEL-FIRS 2DUAL BAND Quick Start Guide3GWINDOW UNITWINDOW UNITCOVERAGEUNITCongratulations on your new indoor signal solution.This Cel-Fi system is designed to provide you with signicant improvements in coverage as well as 3G data rates.Setting up the system is extremely simple and consists of placing and plugging in two components; a Window Unit and a Coverage Unit.By spending just a few minutes using the instructions in this guide, you can optimize the installation and get the very most from your new Cel-Fi System. If you have any trouble during setup, please use the trouble shooting steps included in this guide.In the package you will nd: • Window Unit• Coverage Unit• Two Power AdaptersThis is a CONSUMER device. BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider.You MUST operate this device with approved antennas and cables as specied by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider. WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device.When used with any mobile device utilizing the 1710-1755 MHz band, the FCC limits booster equipment placement to a maximum of 10 meters above ground level. Installation of this equipment which does not comply with federal requirements may subject the owner to FCC enforcement action. NOT FOR RESALE. Changes or modications not expressly approved by Nextivity, Inc. could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for helpCel-Fi is a registered trademark of Nextivity, Inc.Need Help?Visit us at www.celhelp.comfor an installation video and other helpful information regarding installation and trouble shooting.
Step 4Place the Coverage Unit:Move to a location in your home where you need to have improved coverage. Plug the Coverage Unit into an easily accessible outlet. Wait until the numeric display stops cycling. This could take several minutes. At this point you should see a green icon indicating that the unit is working properly. It is possible to place the Coverage Unit so far away that it cannot communicate with the Window Unit. If this happens, a red icon will illuminate indicating that you need to move the Coverage Unit closer to the Window Unit.TOO CLOSEA zero on the numeric display indicates that the Coverage Unit needs to be moved farther away from the Window Unit.GOODThis green icon indicates that the Coverage Unit is functioning normally.TOO FARThis red icon indicates that the Coverage Unit needs to be moved closer to the Window Unit.Step 3 Optimize the Window Unit Placement:The number of bars you can see on the Window Unit make a signicant dierence in the operation of the Cel-Fi system. Try moving the Window Unit to a couple of dierent spots to see if you can get a better signal; the more bars the better. Step 5Optimize The Coverage Unit Placement:The farther away you place the Coverage Unit from the Window Unit the better the coverage in your home, so put the Coverage Unit as far away from the Window Unit as possible. The number shown on the side of the display gives you an indication as to the quality of the placement. Test two or three locations and for best results; try and get an 8 or 9 on the display.COVERAGE UNITWINDOW UNITCOVERAGEUNITWINDOW UNITCEL-FIRS 2 Trouble ShootingIndicator Issue Try ThisIndicator Issue Try ThisIndicator Issue Try ThisImproving Performance Issue Try ThisNo lights on Window Unit display. Status indicator is ashing green for more than a minute.Status indicator is on solid red. No segment lit on signal display and status indicator on solid green.Center three bars on signal display are ashing.No lights on Coverage Unit display. 7 segment display is cycling for more than a minute. 7 segment display shows a value of 0.Red “Too Far” Indicator. Red Status Indicator.E1 E3 E4 E8The key to better performance is the placement of the two units. There is no power. The Window Unit is attempting to select a channel between the units.Hardware Error. Not receiving 3G signal. Network operator data is missing.There is no power. The Coverage Unit is taking longer than normal to make a link. The Coverage Unit is “Too Close” to the Window Unit.The Coverage Unit is “Too Far” from the Window UnitHardware Error. No 3G signal on Window Unit.Coverage Unit is overheating.Window Unit is overheating.Input signal too strong.The Window and Coverage Units are too close together (low coverage number displayed), or the Window Unit displayed signal level could be higher.1. Is the unit plugged in? 2. Is there power at the outlet? 3. Try exchanging the power supplies with the Coverage Unit to see if the power supply is defective.1. Wait for the status indicator to stop ashing, this could take several minutes. 1. Try resetting the Window Unit by unplugging it and then plugging it back in.2. If problem persists return system for service/replacement.1. Try moving the Window Unit to another room or area where you have more coverage. (Use your cell phone to nd the best 3G coverage).1. Insert operator SD card into Window Unit.1. Is the unit plugged in? 2. Is there power at the outlet? 3. Try exchanging the power supplies with the Window Unit to see if the power supply is defective.1. Wait for the display to stop cycling, this could take several minutes 2. Move away from WiFi or other wireless devices. 1. Move the Coverage Unit farther away from the Window Unit.1. Move the Coverage Unit closer to the Window Unit.1. Try resetting the Coverage Unit by unplugging it and then plugging it back in.2. If problem persists return system for service.Try moving the Window Unit to another room or area where you have coverage. (Use your cell phone to nd the best 3G coverage). Make sure that the vents on the unit are not blocked. Move the unit to a cooler area. The system will start working normally when it cools down.The signal from the wireless network is too strong to use a booster.Move Coverage Unit further away from Window Unit to achieve a coverage unit number of 8 or 9 (even placing the Coverage Unit at the opposite end of the house). A higher number means better coverage. You can also improve performance by moving the Window Unit to a location with higher signal. The more bars the better! WINDOW UNITCOVERAGE UNITERROR MESSAGESPERFORMANCEqsg-RS2.2-English_14-0226+((( )))SignalIndicatorsPower & Status

Navigation menu