Nextivity orporated A41-V32-100 Cel-Fi GO Smart Antenna User Manual II

Nextivity Incorporated Cel-Fi GO Smart Antenna II

Contents

User Manual II

Cel-Fi GO SMART ANTENNA Quick Start GuideCel‐Fi GO Smart Antenna is a high‐gain, low‐profile, magnetic‐mounted wideband cellular antenna designed for mobile use on vehicles with the Cel‐Fi GO Smart Signal Booster.QUICK START GUIDEGO SMART ANTENNACEL-FI A41‐V32‐100Instructions: 1 Place the Cel-Fi GO Smart Antenna in the desired location on the vehicle. The Cel-Fi Go Smart Antenna comes with a 3m cable. The cable will connect the Cel-Fi GO to the Smart Antenna. Make sure the Cel-Fi GO is within cable reach. 2 The magnetic base of the Cel-Fi GO Smart Antenna will stick to any ferrous metal. It will not stick to aluminum.The antenna needs to be installed on a metallic surface area (ground plane) of about 30 x 30mm. A vehicle's roof will typically serve this purpose well. NOTE: For best results, install the Cel‐Fi GO Smart Antenna and Server Antennas with as much physical space between them as possible. This will allow the system to configure to maximum gain without oscillation or feedback. 3 If the Cel-Fi GO needs to be installed, follow the instructions that were included with the Cel-Fi GO unit. 4 Make sure to connect the Cel‐Fi GO Smart Antenna to the Cel-Fi GO unit’s Donor port. The Cel-Fi GO is clearly marked with icons for a Donor Antenna Port and a Server Antenna Port. The product will not function if connected in any other manner. NOTE: Use the supplied cable for best results, but any cable can be substituted as long the loss remains <2 dB from the Cel‐Fi GO Smart Antenna to the Cel-Fi GO M unit. 5 Connect the Cel-Fi GO to the power supply. 6 Open the Cel-Fi WAVE app and follow the instructions for pairing a Cel-Fi GO Smart Antenna with a Cel-Fi GO M. NOTE: The Smart Antenna’s serial number can be found on the label on the bottom of the unit. 6 Open the Cel-Fi WAVE app and follow the instructions for pairing a Cel-Fi GO Smart Antenna with a Cel-Fi GO M. NOTE: The Smart Antenna’s serial number can be found on the label on the bottom of the unit.34Cel-Fi GO MCel-Fi Go Smart AntennaServer Antenna5Power123m CableMagnetic BaseCel-Fi GO SMART ANTENNA Quick Start GuideCel‐Fi GO Smart Antenna is a high‐gain, low‐profile, magnetic‐mounted wideband cellular antenna designed for mobile use on vehicles with the Cel‐Fi GO Smart Signal Booster.QUICK START GUIDEGO SMART ANTENNACEL-FI A41‐V32‐100Instructions: 1 Place the Cel-Fi GO Smart Antenna in the desired location on the vehicle. The Cel-Fi Go Smart Antenna comes with a 3m cable. The cable will connect the Cel-Fi GO to the Smart Antenna. Make sure the Cel-Fi GO is within cable reach. 2 The magnetic base of the Cel-Fi GO Smart Antenna will stick to any ferrous metal. It will not stick to aluminum.The antenna needs to be installed on a metallic surface area (ground plane) of about 30 x 30mm. A vehicle's roof will typically serve this purpose well. NOTE: For best results, install the Cel‐Fi GO Smart Antenna and Server Antennas with as much physical space between them as possible. This will allow the system to configure to maximum gain without oscillation or feedback. 3 If the Cel-Fi GO needs to be installed, follow the instructions that were included with the Cel-Fi GO unit. 4 Make sure to connect the Cel‐Fi GO Smart Antenna to the Cel-Fi GO unit’s Donor port. The Cel-Fi GO is clearly marked with icons for a Donor Antenna Port and a Server Antenna Port. The product will not function if connected in any other manner. NOTE: Use the supplied cable for best results, but any cable can be substituted as long the loss remains <2 dB from the Cel‐Fi GO Smart Antenna to the Cel-Fi GO M unit. 5 Connect the Cel-Fi GO to the power supply.34Cel-Fi GO MCel-Fi Go Smart AntennaServer Antenna5Power123m CableMagnetic Base
Cel-Fi GO SMART ANTENNA Quick Start Guide Cel-Fi GO SMART ANTENNA Quick Start GuideCopyright © 2018 by Nextivity, Inc. All rights reserved. The Nextivity and Cel-Fi logos are registered trademarks of Nextivity Inc. All other trademarks or registered trademarks listed belong to their respective owners. qsg-antenna-go-active-eng_18-0316Antenna Specifications: SPECIFICATION698 – 2700120 x 1803:1698 - 960 MHz // 5 dBi> 1 GHz // 6 dBi50VerticalOmni‐directional (effective)SMA‐MDependentMagneticASA UV StableBlack‐-20C - 55C66ITEMFrequency (MHz)Dimensions (mm)VSWRGain: Gain: Impedance (Ohm)PolarizationRadiation patternConnector typeGround planeMounting TypeRadomeColorOperating TempIPCel-Fi WAVE is available on both smartphones and tablets from the following app stores.Instructions: 1 Place the Cel-Fi GO Smart Antenna in the desired location on the vehicle. The Cel-Fi Go Smart Antenna comes with a 3m cable. The cable will connect the Cel-Fi GO to the Smart Antenna. Make sure the Cel-Fi GO is within cable reach. 2 The magnetic base of the Cel-Fi GO Smart Antenna will stick to any ferrous metal. It will not stick to aluminum.The antenna needs to be installed on a metallic surface area (ground plane) of about 30 x 30mm. A vehicle's roof will typically serve this purpose well. NOTE: For best results, install the Cel‐Fi GO Smart Antenna and Server Antennas with as much physical space between them as possible. This will allow the system to configure to maximum gain without oscillation or feedback. 3 If the Cel-Fi GO needs to be installed, follow the instructions that were included with the Cel-Fi GO unit. 4 Make sure to connect the Cel‐Fi GO Smart Antenna to the Cel-Fi GO unit’s Donor port. The Cel-Fi GO is clearly marked with icons for a Donor Antenna Port and a Server Antenna Port. The product will not function if connected in any other manner. NOTE: Use the supplied cable for best results, but any cable can be substituted as long the loss remains <2 dB from the Cel‐Fi GO Smart Antenna to the Cel-Fi GO M unit. 5 Connect the Cel-Fi GO to the power supply. 6 Open the Cel-Fi WAVE app and follow the instructions for pairing a Cel-Fi GO Smart Antenna with a Cel-Fi GO M. NOTE: The Smart Antenna’s serial number can be found on the label on the bottom of the unit.Copyright © 2018 by Nextivity, Inc. All rights reserved. The Nextivity and Cel-Fi logos are registered trademarks of Nextivity Inc. All other trademarks or registered trademarks listed belong to their respective owners. qsg-antenna-go-active-eng_18-0316Antenna Specifications: SPECIFICATION698 – 2700120 x 1803:1698 - 960 MHz // 5 dBi> 1 GHz // 6 dBi50VerticalOmni‐directional (effective)SMA‐MDependentMagneticASA UV StableBlack‐-20C - 55C66ITEMFrequency (MHz)Dimensions (mm)VSWRGain: Gain: Impedance (Ohm)PolarizationRadiation patternConnector typeGround planeMounting TypeRadomeColorOperating TempIPCel-Fi WAVE is available on both smartphones and tablets from the following app stores. 6 Open the Cel-Fi WAVE app and follow the instructions for pairing a Cel-Fi GO Smart Antenna with a Cel-Fi GO M. NOTE: The Smart Antenna’s serial number can be found on the label on the bottom of the unit.Instructions: 1 Place the Cel-Fi GO Smart Antenna in the desired location on the vehicle. The Cel-Fi Go Smart Antenna comes with a 3m cable. The cable will connect the Cel-Fi GO to the Smart Antenna. Make sure the Cel-Fi GO is within cable reach. 2 The magnetic base of the Cel-Fi GO Smart Antenna will stick to any ferrous metal. It will not stick to aluminum.The antenna needs to be installed on a metallic surface area (ground plane) of about 30 x 30mm. A vehicle's roof will typically serve this purpose well. NOTE: For best results, install the Cel‐Fi GO Smart Antenna and Server Antennas with as much physical space between them as possible. This will allow the system to configure to maximum gain without oscillation or feedback. 3 If the Cel-Fi GO needs to be installed, follow the instructions that were included with the Cel-Fi GO unit. 4 Make sure to connect the Cel‐Fi GO Smart Antenna to the Cel-Fi GO unit’s Donor port. The Cel-Fi GO is clearly marked with icons for a Donor Antenna Port and a Server Antenna Port. The product will not function if connected in any other manner. NOTE: Use the supplied cable for best results, but any cable can be substituted as long the loss remains <2 dB from the Cel‐Fi GO Smart Antenna to the Cel-Fi GO M unit. 5 Connect the Cel-Fi GO to the power supply.

Navigation menu