NexAira NEX09 NexConnect II Router User Manual 1

NexAira Inc. NexConnect II Router 1

UserManual.wiki >

NEX09 User Manual >

Contents

1. user manual 1
2. user manual 2

user manual 1

USB

Table of ContentsIntroduction.......................................................................................................................................................1Features..........................................................................................................................................1Package Contents..........................................................................................................................2System Requirements....................................................................................................................2Wi-Fi Requirements......................................................................................................................2Hardware Overview..........................................................................................................................................3Default Router Settings......................................................................................................................................4 Hardware Setup................................................................................................................................................5Wi-Fi Connection..........................................................................................................................6Initial /Wireless Setup.............................................................................................................................7 Installation and Conguration Settings.........................................................................................7NexWare Setup Wizard......................................................................................................................................7Basic Settings.....................................................................................................................................................9Admin Password............................................................................................................................9Wi-Fi..............................................................................................................................................9Wired Interfaces..........................................................................................................................10Cellular Datacard.........................................................................................................................11Realtime Network Trafc.............................................................................................................11Logout..........................................................................................................................................11Tool Box............................................................................................................................................................12System Settings...........................................................................................................................12Email Notications......................................................................................................................12 System Log..................................................................................................................................13Flash Firmware............................................................................................................................13Backup Interface..........................................................................................................................13Reset to Defaults..........................................................................................................................13Reboot..........................................................................................................................................13Advanced Settings...........................................................................................................................................14DHCP Server...............................................................................................................................14SNMP (Simple Network Management Protocol)........................................................................14Dynamic DNS.............................................................................................................................15QoS (Quality of Service)..............................................................................................................16Security Settings..............................................................................................................................................17Remote Admin.............................................................................................................................17IPsec.............................................................................................................................................17SSH Server..................................................................................................................................18SSH Keys....................................................................................................................................18Routing Settings..............................................................................................................................................18Routes.........................................................................................................................................18RIP..............................................................................................................................................19DMZ Host..................................................................................................................................19VRRP..........................................................................................................................................20Internet Failover.........................................................................................................................21Port Forwarding..........................................................................................................................21UPnP...........................................................................................................................................22Table of ContentsIntroduction.......................................................................................................................................................1Features..........................................................................................................................................1Package Contents..........................................................................................................................2System Requirements....................................................................................................................2Wi-Fi Requirements......................................................................................................................2Hardware Overview..........................................................................................................................................3Default Router Settings......................................................................................................................................4 Hardware Setup................................................................................................................................................5Wi-Fi Connection..........................................................................................................................6Initial 3G/4G Wireless Setup.............................................................................................................................7 Installation and Conguration Settings.........................................................................................7NexWare Setup Wizard......................................................................................................................................7Basic Settings.....................................................................................................................................................9Admin Password............................................................................................................................9Wi-Fi..............................................................................................................................................9Wired Interfaces..........................................................................................................................10Cellular Datacard.........................................................................................................................11Realtime Network Trafc.............................................................................................................11Logout..........................................................................................................................................11Tool Box............................................................................................................................................................12System Settings...........................................................................................................................12Email Notications......................................................................................................................12 System Log..................................................................................................................................13Flash Firmware............................................................................................................................13Backup Interface..........................................................................................................................13Reset to Defaults..........................................................................................................................13Reboot..........................................................................................................................................13Advanced Settings...........................................................................................................................................14DHCP Server...............................................................................................................................14SNMP (Simple Network Management Protocol)........................................................................14Dynamic DNS.............................................................................................................................15QoS (Quality of Service)..............................................................................................................16Security Settings..............................................................................................................................................17Remote Admin.............................................................................................................................17IPsec.............................................................................................................................................17SSH Server..................................................................................................................................18SSH Keys....................................................................................................................................18Routing Settings..............................................................................................................................................18Routes.........................................................................................................................................18RIP..............................................................................................................................................19DMZ Host..................................................................................................................................19VRRP..........................................................................................................................................20Internet Failover.........................................................................................................................21Port Forwarding..........................................................................................................................21UPnP...........................................................................................................................................22

Troubleshooting....................................................................................................................................................23Technical Support................................................................................................................................................26Technical Specications.........Glossary of Denitions...........Troubleshooting....................................................................................................................................................23Technical Support................................................................................................................................................26Technical Specications.........Glossary of Denitions...........

27 dBm

Package ContentsImportant: Check the contents of the box rst.The Business Class II High Availability Router package should contain the items listed below. If any of the items are missing, please contact your reseller.(1) Business Class II High Availability Router(1) CD-ROM(1) RJ-45 Ethernet Cable(1) Switching 12V 1.25A Power AdapterCaution: Using a power supply with a different voltage rating other than the one included with the Business Class II High Availability Router will cause damage and void the warranty for this prod-uct.System Requirements• Compatible with ExpressCard or USB 3G/4G modem card with activated service. * NOTE: Subject to terms available from your carrier.• Computer with Windows XP, Vista, Windows 7, Macintosh, or Linux-based operating system with an integrated Ethernet adapter or Wireless Wi-Fi 802.11 G interface.• Internet Explorer, Firefox, Safari, and Google Chrome (for accessing web-based conguration settings).Wi-Fi Requirements• IEEE 802.11 b/g/n adapter.*ExpressCards, and USB modems need to be activated through your cellular service provider prior to insertion into the Business Class II High Availability Router.Package ContentsImportant: Check the contents of the box rst.The Business Class II High Availability Router package should contain the items listed below. If any of the items are missing, please contact your reseller.(1) Business Class II High Availability Router(1) CD-ROM(1) RJ-45 Ethernet Cable(1) Switching 12V 1.25A Power AdapterCaution: Using a power supply with a different voltage rating other than the one included with the Business Class II High Availability Router will cause damage and void the warranty for this prod-uct.System Requirements• Compatible with ExpressCard or USB 3G/4G modem card with activated service. * NOTE: Subject to terms available from your carrier.• Computer with Windows XP, Vista, Windows 7, Macintosh, or Linux-based operating system with an integrated Ethernet adapter or Wireless Wi-Fi 802.11 G interface.• Internet Explorer, Firefox, Safari, and Google Chrome (for accessing web-based conguration settings).Wi-Fi Requirements• IEEE 802.11 b/g/n adapter.*ExpressCards, and USB modems need to be activated through your cellular service provider prior to insertion into the Business Class II High Availability Router.

Receptors and Ports (Rear View)LEDs (Front View)ExpressCard and Serial Console Port (Side View)USB Port:Allows connection witha 3G/4G USB modem.ExpressCard Port:Allows connection with an ExpressCard modem.Serial Console PortPower Receptor:Compatible withincluded 12V 1.25A adapter.Reset Button:Resets the Router to factory default settings.WAN/LAN Ports:Automatically senses WAN andLAN types when connecting toEthernet. WAN can be converted to an additional LAN port.Hardware OverviewLAN LED:Lights up blue when a localEthernet cable is connectedand blinks to indicate activity.Wi-Fi LED:Light blinks blue whena connection to the Wi-Fiis available.WAN LED:Lights up blue whenWAN is connected.3G LED:Solid blue when connected. Power indicated by consistant blink.Receptors and Ports (Rear View)LEDs (Front View)ExpressCard and Serial Console Port (Side View)USB Port:Allows connection witha 3G/4G USB modem.ExpressCard Port:Allows connection with an ExpressCard modem.Serial Console PortSerial Console PortPower Receptor:Compatible withincluded 12V 1.25A adapter.Reset Button:Resets the Router to factory default settings.WAN/LAN Ports:Automatically senses WAN andLAN types when connecting toEthernet. WAN can be converted to an additional LAN port.Hardware OverviewLAN LED:Lights up blue when a localLights up blue when a localEthernet cable is connectedEthernet cable is connectedand blinks to indicate activity.and blinks to indicate activity.Wi-Fi LED:Wi-Fi LED:Light blinks blue whenLight blinks blue whena connection to the Wi-Fia connection to the Wi-Fiis available.is available.WAN LED:Lights up blue whenWAN is connected.3G LED:Solid blue when connected. Power indicated by consistant blink.USBUSB LED:

Default Router SettingsLogin Screen Username / Password root /adminWi-Fi Interface Devices enabled Channel Auto selectESSID NEXWARE### (### are the last 3 digits of the Router’s MAC AddressSecurity WPA-PSK / WPA2-PSKKey passwordWired Interfaces IPv4 Address / Netmask 192.168.1.1 / 255.255.255.0DNS Server 208.67.222.222 / 208.67.220.220Cellular Datacard 3G Service Auto detectSystem Settings Hostname NexWareTimezone UTCEmail Notications disabledDHCP Server enabledFirst leased address 100Number of leased 151Lease time 12hStatic Leases noneDynamic DNS disabledPort Forwarding noneQuality of Service (QoS) enabledRoutes Static IPv4 noneSNMP disabledRemote Admin disabledPort 8080IPsec disabledSSH Server disabledVRRP disabledInternet Failover disabled UPnP disabled Default Router SettingsLogin Screen Username / Passwordroot /adminWi-Fi InterfaceDevicesenabled ChannelAuto selectESSID NEXWARE### (### are the last 3 digits of the Router’s MAC AddressSecurity WPA-PSK / WPA2-PSKKeypasswordWired InterfacesIPv4 Address / Netmask192.168.1.1 / 255.255.255.0DNS Server208.67.222.222 / 208.67.220.220Cellular Datacard3G ServiceAuto detectSystem SettingsHostnameNexWareTimezoneUTCEmail NoticationsdisabledDHCPServerenabledFirst leased address100Number of leased151Lease time12hStatic LeasesnoneDynamic DNS disabledPort ForwardingnoneQuality of Service (QoS)enabledRoutesStatic IPv4noneSNMPdisabledRemote AdmindisabledPort8080IPsecdisabledSSH ServerdisabledVRRPdisabledInternet Failoverdisabled UPnPdisabled

Hardware SetupThe Business Class II High Availability Router allows you to access your net-work using a wireless connection from virtually anywhere within its operating range. Please note that location placement of the router could affect the wire-less signal and range limits.Typical ranges also vary depending on the types of materials and background RF (Radio Frequency) noise present in your networking environment. To maximize your wireless range, please follow these guidelines:1. Choose the right location in your environment for the 3G/4G Wireless Broadband Router. The WLAN transmitters are radios, and degrade as they go through walls, oors, and obstacles like tubs full of water (almost impenetrable), stone, or concrete. So for best reception, place your router centrally to the rooms in which you expect to use WLAN the most. Each wall or ceiling can reduce the Business Class II II High Availability Router’s range by as much as 90 feet (27 meters). NOTE: The same considerations apply to your carrier’s 3G/4G broadband carrier’s connection.2. Keep your product away from electrical devices (such as microwaves, air conditioners, cordless phones, refrigerators and televisions) that emit large quantities of RFI (Radio Frequency Interference).NOTE: DO NOT connect the Business Class II High Availability Router to power before following the in-stallation steps below!Business Class II High Availability Router Setup1. ExpressCard or USB connection: a. Insert an activated ExpressCard into the card slot. b. Alternatively, insert an activated USB modem into the USB slot.a. b.Hardware SetupThe Business Class II High Availability Router allows you to access your net-work using a wireless connection from virtually anywhere within its operating range. Please note that location placement of the router could affect the wire-less signal and range limits.Typical ranges also vary depending on the types of materials and background RF (Radio Frequency) noise present in your networking environment. To maximize your wireless range, please follow these guidelines:1. Choose the right location in your environment for the 3G/4G Wireless Broadband Router. The WLAN transmitters are radios, and degrade as they go through walls, oors, and obstacles like tubs full of water (almost impenetrable), stone, or concrete. So for best reception, place your router centrally to the rooms in which you expect to use WLAN the most. Each wall or ceiling can reduce the Business Class II II High Availability Router’s range by as much as 90 feet (27 meters).NOTE: The same considerations apply to your carrier’s 3G/4G broadband carrier’s connection.2. Keep your product away from electrical devices (such as microwaves, air conditioners, cordless phones, refrigerators and televisions) that emit large quantities of RFI (Radio Frequency Interference).NOTE: DO NOT connect the Business Class II High Availability Router to power before following the inNOTE: DO NOT connect the Business Class II High Availability Router to power before following the inNOTE: DO NOT-stallation steps below!Business Class II High Availability Router Setup1. ExpressCard or USB connection:a. Insert an activated ExpressCard into the card slot.b. Alternatively, insert an activated USB modem into the USB slot.a.b.

2(ii). Ethernet connection:a. Insert one end of an Ethernet cable into the LAN Port on the back panel of the router. Insert the other end into an available Ethernet port of the network adapter in the computer that will be used to congure the unit.b. LAN LED should be on when connected. If not, check the connection between the router and computer.NOTE: The Business Class II High Availability Router LAN Port is “Auto-MDI/MDIX”, so any standard Ethernet cable will work. 3. Power connection.a. Connect the power adapter to the receptor on the back panel of the router. Plug the other end of the power adapter into a wall outlet or power strip.b. The 3G & Wi-Fi LED will turn ON and ash, indicating that the unit is powered on. Also performing the boot-up cycle. The LAN and WAN lights will be on if connected.c. The 3G/4G LED will ash and stabilize once a 3G/4G connection is established.d. Upon completion of the boot-up cycle, the 3G light, LAN and Wi-Fi lights will be on. Occational ashing may occur indicating normal activity.NOTES: An uninterruptable power supply (UPS) is recommended for power surges and/oroutages. At a minimum, a surge protector should always be used to protect theequipment from being damaged by electrical spikes and transients.Wi-Fi ConnectionIf you are connecting wirelessly to the Business Class II High Availability Router, you must ensure that the security settings on the connecting PC are the same as those on the router. By default, the router broadcasts a secure Wi-Fi signal with WPA-PSK* encryption:• SSID / Wi-Fi Signal Name is set to NEXWARE### (where ### equal the last three characters of the router’s MAC address)• Channel is set to channel 5(2.4GHz)• Security is set to WPA-PSK*• Key (password) is set to passwordNOTE: It is recommended, for security reasons, that the security settings on the router be changed during initial setup.*Please refer to your computer’s Wi-Fi adapter documentation for additional information.2(ii). Ethernet connection:a. Insert one end of an Ethernet cable into the LAN Port on the back panel of the router. Insert the other end into an available Ethernet port of the network adapter in the computer that will be used to congure the unit.b. LAN LED should be on when connected. If not, check the connection between the router and computer.NOTE: The Business Class II High Availability Router LAN Port is “Auto-MDI/MDIX”, so any standard Ethernet cable will work. 3. Power connection.a. Connect the power adapter to the receptor on the back panel of the router. Plug the other end of the power adapter into a wall outlet or power strip.b. The 3G & Wi-Fi LED will turn ON and ash, indicating that the unit is powered on. Also performing the boot-up cycle. The LAN and WAN lights will be on if connected.c. The 3G/4G LED will ash and stabilize once a 3G/4G connection is established.d. Upon completion of the boot-up cycle, the 3G light, LAN and Wi-Fi lights will be on. Occational ashing may occur indicating normal activity.NOTES: An uninterruptable power supply (UPS) is recommended for power surges and/oroutages. At a minimum, a surge protector should always be used to protect theequipment from being damaged by electrical spikes and transients.Wi-Fi ConnectionIf you are connecting wirelessly to the Business Class II High Availability Router, you must ensure that the security settings on the connecting PC are the same as those on the router. By default, the router broadcasts a secure Wi-Fi signal with WPA-PSK* encryption:• SSID / Wi-Fi Signal Name is set to NEXWARE### (where ### equal the last three characters of the router’s MAC address)• Channel is set to channel 5(2.4GHz)• Security is set to WPA-PSK*• Key (password) is set to passwordNOTE: It is recommended, for security reasons, that the security settings on the router be changed during initial setup.*Please refer to your computer’s Wi-Fi adapter documentation for additional information.

Initial 3G/4G Wireless SetupConnecting to the Router Main Page for Installation and Congurations SettingsFollow the steps below to access the Router and perform installation and congure settings: 1) Open a web browser on your computer connected to the router’s LAN port by and Ethernet cable. 2) Enter the IP address of the Router in the URL line of your web browser. http://192.168.1.1NOTE: If you have changed the router’s default IP address, enter that address instead of the one above. 3) Type “admin” in the Password eld. If you have changed the password, enter the new one in this eld. NOTE: Default Username is “root”. 4) Click the “Login” button. 5) You will be greeted by the iconic home page. Setup WizardSelect the Setup Wizard Icon. Select the Next button to proceed with the indicated steps of the automated setup process.1) Change your administration password. It is recommended that the default password (admin) be replaced for security reasons. Enter your new password and then re-enter to conrm. Select Next to retain any changes and move to the next step. 2) Congure your Wired Internet connection.a. During the boot up process of the router if your wide area network (WAN) Ethernet cable is plugged into the WAN port of the router, the router will auto-matically be connected to your ISP.b. If your ISP requires you to setup the WAN as a PPPoE or PPTP, you will need to enter your ISP’s required infor-mation into the proper elds. i. PPPoE. Typical entries in-clude the Username and Password ii. PPTP. Typical entries in-clude the Username, Password, and the PPTPServer Name. 3a) Congure your wireless settings.This step allows you to change whether the Wi-Fi is enabled, the channel on which the Wi-Fi is broadcast on, the wireless mode (b,g,n or mixed), the name that is broadcast, the security and encryption type, and the key (password) to access the broadcasted Wi-Fi signal.• Disable only if you do not want anyone accessing the router wirelessly.• Change channel if other wireless devices are interfering with the router. By default the router will auto-select the channel.• Select the wireless mode, choose from b,g,n or a mix. • The router’s mode is factory set to provide (Access Point)• Change the Network Name (ESSID) to whatever name you wish to be broadcasted• Hiding the ESSID does not disable the WiFi signal and should not be thought of as security setting. Initial 3G/4G Wireless SetupConnecting to the Router Main Page for Installation and Congurations SettingsFollow the steps below to access the Router and perform installation and congure settings:1) Open a web browser on your computer connected to the router’s LAN port by and Ethernet cable.2) Enter the IP address of the Router in the URL line of your web browser. http://192.168.1.1NOTE: If you have changed the router’s default IP address, enter that address instead of the one above. 3) Type “admin” in the Password eld. If you have changed the password, enter the new one in this eld. NOTE: Default Username is “root”.4) Click the “Login” button.5) You will be greeted by the iconic home page. Setup WizardSelect the Setup Wizard Icon. Select the Next button to proceed with the indicated steps of the automated setup process.1) Change your administration password. It is recommended that the default password (admin) be replaced for security reasons. Enter your new password and then re-enter to conrm. Select Next to retain any changes and move to the next step. 2) Congure your Wired Internet connection.a. During the boot up process of the router if your wide area network (WAN) Ethernet cable is plugged into the WAN port of the router, the router will auto-matically be connected to your ISP.b. If your ISP requires you to setup the WAN as a PPPoE or PPTP, you will need to enter your ISP’s required infor-mation into the proper elds. i. PPPoE. Typical entries in-clude the Username and Password ii. PPTP. Typical entries in-clude the Username, Password, and the PPTPServer Name. 3a) Congure your wireless settings.This step allows you to change whether the Wi-Fi is enabled, the channel on which the Wi-Fi is broadcast on, the wireless mode (b,g,n or mixed), the name that is broadcast, the security and encryption type, and the key (password) to access the broadcasted Wi-Fi signal.• Disable only if you do not want anyone accessing the router wirelessly.• Change channel if other wireless devices are interfering with the router. By default the router will auto-select the channel.• Select the wireless mode, choose from b,g,n or a mix. • The router’s mode is factory set to provide (Access Point)• Change the Network Name (ESSID) to whatever name you wish to be broadcasted• Hiding the ESSID does not disable the WiFi signal and should not be thought of as security setting.

Hiding the ESSID only eliminates the name from being broadcasted.• Change encryption type as necessary. Some wireless devices cannot connect to all encryption modes. The default setting is WPA-PSK. Other typical choices include WEP (ASCII or Hex), WPA=PSK, or WPA2-PSK. Additional available settings require additional software or hardware not included with this router.• Change Key (password). We suggest that this setting be changed. This setting controls the require Key or password to access your wireless signal.• Choose to lter by MAC Address. 3b) 3G/4G Internet Connection Setup.a. During the boot up process of the router all compatible data cards are recognized and are setup au-tomatically. No additional information is typically required to complete the setup of your compatible 3G/4G data card.b. If your ISP requires additional information to connect to their network, please refer to their documen-tation for APN, PIN Code, Username, and Password. All data entry elds may not be required to con-nect to your ISP’s network.c. Avalible options and selections are dependant on the presence of a datacard and the carrier network type.4) Select Next to retain any changes and move to the Completion page and select Finish. Hiding the ESSID only eliminates the name from being broadcasted.• Change encryption type as necessary. Some wireless devices cannot connect to all encryption modes. The default setting is WPA-PSK. Other typical choices include WEP (ASCII or Hex), WPA=PSK, or WPA2-PSK. Additional available settings require additional software or hardware not included with this router.• Change Key (password). We suggest that this setting be changed. This setting controls the require Key or password to access your wireless signal.• Choose to lter by MAC Address. 3b) 3G/4G Internet Connection Setup.a. During the boot up process of the router all compatible data cards are recognized and are setup au-tomatically. No additional information is typically required to complete the setup of your compatible 3G/4G data card.b. If your ISP requires additional information to connect to their network, please refer to their documen-tation for APN, PIN Code, Username, and Password. All data entry elds may not be required to con-nect to your ISP’s network.c. Avalible options and selections are dependant on the presence of a datacard and the carrier network type.4) Select Next to retain any changes and move to the Completion page and select Finish.

BasicsAdmin PasswordYou can change the router’s administrative password. (default = admin)Wi-Fi SettingsHere you can change whether the Wi-Fi is enabled, the channel on which the Wi-Fi is broadcast on, the name that is broadcast, the wireless mode, the encryption type, the key (password) to access the broadcasted Wi-Fi signal, and enable Wireless Distribution System (WDS). • Disable only if you do not want anyone accessing the router wirelessly.• Change channel if other wireless devices are interfering with the router.• Change the router’s Wireless Mode. Choose from six settings, b, g, or n and mixes. • Routing mode is factory set to Provide (Access Point). • Choose to hide the ESSID.• Change the Network Name (ESSID) to whatever name you wish to be broadcasted.• Change security and encryption type as necessary. Some wireless devices cannot connect to all security modes.• Change Key (password). We suggest that this setting be changed.• Choose to enable MAC Address ltering, then select lter policy and create the address list. NOTE: After any changes, select ”Save” to retain. System will refresh following, “Save”.WDS: Wireless Distribution System (WDS) is a feature that allows multiple access points of the same physical radio type to be bridged together as one common WiFi network. Because the same physical radio type must be used, this feature only operates with other Nexaira routers. The following conguration options are avail-able:• BSSID: Your router supports up to four WDS clients. Enter the BSSID (MAC address listed on the bottom label of the router, also listed under LAN on the Wired Interfaces page) of the other devices to be connected to via WDS.BasicsAdmin PasswordYou can change the router’s administrative password. (default = admin)Wi-Fi SettingsHere you can change whether the Wi-Fi is enabled, the channel on which the Wi-Fi is broadcast on, the name that is broadcast, the wireless mode, the encryption type, the key (password) to access the broadcasted Wi-Fi signal, and enable Wireless Distribution System (WDS). • Disable only if you do not want anyone accessing the router wirelessly.• Change channel if other wireless devices are interfering with the router.• Change the router’s Wireless Mode. Choose from six settings, b, g, or n and mixes. • Routing mode is factory set to Provide (Access Point). • Choose to hide the ESSID.• Change the Network Name (ESSID) to whatever name you wish to be broadcasted.• Change security and encryption type as necessary. Some wireless devices cannot connect to all security modes.• Change Key (password). We suggest that this setting be changed.• Choose to enable MAC Address ltering, then select lter policy and create the address list. NOTE: After any changes, select ”Save” to retain. System will refresh following, “Save”.WDS: Wireless Distribution System (WDS) is a feature that allows multiple access points of the same physical radio type to be bridged together as one common WiFi network. Because the same physical radio type must be used, this feature only operates with other Nexaira routers. The following conguration options are avail-able:• BSSID: Your router supports up to four WDS clients. Enter the BSSID (MAC address listed on the bottom label of the router, also listed under LAN on the Wired Interfaces page) of the other devices to be connected to via WDS.

Wired InterfacesHere you can review WAN, and LAN status as well as change Local Network, and WAN Ethernet settings.• The IP address is the address of the router. It is also your local network’s gateway address which is used by all LAN hosts to access the Internet through the WAN connection.• The Netmask is used to determine the number of subnetworks that can be connected to the router.• The IP Gateway (optional) eld is and advanced an optional setting that is available if your local network has a gateway that is different than the router’s LAN IP address.• DNS Server (optional) allows you to specify a DNS server for LAN hosts to use if your WAN connection does not supply a valid server address, or if not-peer DNS Server information is required or chosen under Cellular Datacard settings. • Change WAN port into a second LAN port.• Enable IP Passthrough mode to have one client have the WAN IP. All router functions are disabled.• Enable or disable the router’s ability to connect to the internet through a WAN Ethernet connection.NOTE: After any changes, select ”Save” to retain. System will refresh following, “Save”.Wired InterfacesHere you can review WAN, and LAN status as well as change Local Network, and WAN Ethernet settings.• The IP address is the address of the router. It is also your local network’s gateway address which is used by all LAN hosts to access the Internet through the WAN connection.• The Netmask is used to determine the number of subnetworks that can be connected to the router.• The IP Gateway (optional) eld is and advanced an optional setting that is available if your local network has a gateway that is different than the router’s LAN IP address.• DNS Server (optional) allows you to specify a DNS server for LAN hosts to use if your WAN WAN W connection does not supply a valid server address, or if not-peer DNS Server information is required or chosen under Cellular Datacard settings. • Change WAN port into a second LAN port.• Enable IP Passthrough mode to have one client have the WAN IP. All router functions are disabled.• Enable or disable the router’s ability to connect to the internet through a WAN Ethernet connection.NOTE: After any changes, select ”Save” to retain. System will refresh following, “Save”.

Cellular Datacard • Enable or disable the router’s ability to access the Internet through a datacard• Select Service type: UMTS/GPRS, CDMA (default), or EV-DO.• Insert Access Point (APN), PIN code, Username, and Password as indicated by your 3G/4G wire less provider.• Select to use the Peer DNS or an optional location. Input DNS Server information in Wired Interfaces.• Enable Keep-Alive to determine it the connection is up. Router well re-initilize connection if connection is down. • Input time (in seconds) of inactivity until link is disconnected. NOTE: Settings are auto-populated when an activated compatible datacard is inserted. Realtime Network TrafcThe Network Trafc status screen shows current trafc status of active interfaces, such as the LAN, the connected Datacard, and the WAN.LogoutHere you will be logged out of administrative mode. You will be returned to the login screen.Cellular Datacard • Enable or disable the router’s ability to access the Internet through a datacard• Select Service type: UMTS/GPRS, CDMA (default), or EV-DO.• Insert Access Point (APN), PIN code, Username, and Password as indicated by your 3G/4G wireless provider.• Select to use the Peer DNS or an optional location. Input DNS Server information in Wired Interfaces.Wired Interfaces.W• Enable Keep-Alive to determine it the connection is up. Router well re-initilize connection if connection is down. • Input time (in seconds) of inactivity until link is disconnected. NOTE: Settings are auto-populated when an activated compatible datacard is inserted. Realtime Network TrafcThe Network Trafc status screen shows current trafc status of active interfaces, such as the LAN, the connected Datacard, and the WAN.LogoutHere you will be logged out of administrative mode. You will be returned to the login screen.

Navigation menu