Neutrik XPR Digital Wireless Audio Network User Manual part 1

Neutrik AG Digital Wireless Audio Network part 1

User Manual part 1

User ManualApplies to XIRIUM PRO CANADA, AUSTRALIA, andNEW ZEALAND devices
2User Manual – XIRIUM PRO® CA | BDA 471 2017/03 ImprintSubject to change due to technical advances! This user manual corresponds to the level of technology at the time the product was delivered and not the current stage of development at Neutrik.If any pages or sections of this user manual are missing, please contact the manufacturer at the address listed below.CopyrightThis user manual is protected by copyright. The user manual must not be duplicated, reproduced, microlmed or translated, or converted to be saved and processed in EDP systems, neither as excerpts nor in full, without the express written authorization of Neutrik.Copyright by: © Neutrik® AGDocument identificationDocument No: BDA 470Version: 2017/03 cThis user manual applies to firmware 3.0 and app version 3.0!Language: EnglishOriginal language: GermanEach user manual in a different language is a translation of the operating manual in German.ManufacturerNeutrik® AGIm alten Riet 1439494 Schaan LiechtensteinT: +423 2372424F: +423 2325393E: neutrik@neutrik.comwww.neutrik.com
3User Manual – XIRIUM PRO® CA | BDA 471 2017/03 Table of contents1 About this document ..............................................41.1 Signicance of the user manual .............................41.2 Designation ..........................................................41.3 Explanation of symbols .........................................51.3.1 Symbols in illustrations ....................................51.4 Target group .........................................................52 Safety ........................................................................62.1 Warning information and signal words ..................62.2 Warning symbols ..................................................62.3 Important regulatory notes ...................................72.3.1 Radio frequency radiation exposure informa-tion .........................................................................82.4 Important safety instructions .................................82.5 Proper use ..........................................................102.6 Foreseeable improper use ................................... 103 Components and accessories ................................ 113.1 XIRIUM PRO components .................................... 114 Description of product ..........................................134.1 X IRIUM PRO base station ..................................... 134.2 Modules ............................................................. 144.2.1 TX modules ...................................................144.2.2 RX modules .................................................. 144.3 XIRIUM PRO app ................................................. 154.3.1 Overview of operation elements .................... 154.3.2 Links/Overview page .....................................174.3.3 Edit page ......................................................184.3.4 Settings page ................................................214.3.5 Help page ..................................................... 224.4 Getting started ...................................................234.4.1 App ..............................................................244.4.2 Repeater ....................................................... 244.4.3 Signal quality bar ..........................................244.4.4 Transmission power ......................................254.4.5 XROC mode .................................................264.4.6 Antennas ......................................................264.4.7 Line-of-sight and redundant RF path .............284.4.8 Antenna height + distance ............................ 284.4.9 Line-of-sight and redundant RF path .............304.5 Selecting transmission channels ..........................314.5.1 Automatic selection of transmission channels ...314.5.2 Manual selection of transmission channels ....315 Operation ...............................................................325.1 Setting devices into operation .............................325.2 Setting up the transmission path ......................... 335.3 Installing and starting the app .............................345.4 Connecting devices with the app ........................345.4.1 Connecting devices in stand-alone mode ......345.4.2 Connecting devices in network mode ...........355.5 Arranging the radio transmission path .................385.6 Conguring the device parameters ...................... 395.7 Editing system settings ........................................ 435.7.1 System reset ..................................................435.7.2 Advanced Mode ...........................................435.8 Setting up and mounting the XIRIUM PRO system .. 445.8.1 Positioning the devices ..................................445.8.2 Positioning the repeater ................................ 455.8.3 Systems with several transmitters ..................455.8.4 Fastening and securing XIRIUM PRO devices ... 465.9 Upgrading rmware ............................................475.9.1 Installing the XIRIUM PRO Firmware Upgrade Manager ................................................................475.9.2 Executing a rmware upgrading ...................485.9.3 Uninstalling the XIRIUM PRO Firmware Upgrade Manager ................................................................ 506 Troubleshooting.....................................................517 After operation ......................................................527.1 Dismounting devices ............................................527.2 Transporting ........................................................527.3 Storage ...............................................................527.4 Cleaning and care ...............................................527.5 Maintenance and repair .......................................527.6 Dispo sal ..............................................................538 Appendix ................................................................548.1 Integrating DANTE ..............................................548.1.1 Introduction to DANTETM ...............................548.1.2 Enabling a DANTETM link ................................ 548.2 Access point settings ..........................................558.2.1 Recommended settings .................................558.2.2 XIRIUM PRO basic kit with access point .........558.3 Technical specications .......................................56
4User Manual – XIRIUM PRO® CA | BDA 471 2017/03About this document1 About this documentThis user manual provides an overview of the necessary operation steps and settings of the product. 1.1 Significance of the user manualThis user manual is an integral component of the product and part of the product's safety concept. cMake sure that all persons who work with the product have fully read and also understood this user manual. cObserve all instructions exactly, especially the safety instructions.This user manual contains important information for operating and maintaining the product and troubleshooting minor problems safely and properly on your own. cKeep this user manual in the immediate vicinity of the product so personnel have access to it at all times. cPass this user manual on to every user, e.g., by lending it, or to the future owner of the product. cIf this user manual is lost or damaged, a copy of the operating manual can be downloaded from the Neutrik's home page (www.neutrik.com).1.2 DesignationDesignation ExplanationXIRIUM PRO System All components:XIRIUM PRO base stations, XIRIUM PRO modules, cables, plugs, antennasXIRIUM PRO base stationXIRIUM PRO TX (transmitter) without module, short TXXIRIUM PRO RX (receiver) without module, short RXXIRIUM PRO module Exchangeable module for the XIRIUM PRO base stationXIRIUM PRO device XIRIUM PRO base station with module plugged-inXROC mode Extreme Ruggedized One Channel mode for a secure connection in extreme situations.Peripheral devices All devices which can be connected with each other via the XIRIUM PRO devices: audio sources (transmitters) and audio sinks (receivers)Audio source All devices which emit a signalAudio sink All devices which receive the audio signals, e.g., loudspeakers, audio systems (ampliers, mixing consoles, etc.)Transmission path Wireless connection between the XIRIUM PRO devices.A transmission path consists of 1 TX, 1 repeater (optional) and at least 1 RX.Network All devices used which are connected to the app via an access point.
5User Manual – XIRIUM PRO® CA | BDA 471 2017/03About this document1.3 Explanation of symbolsIn order to make this user manual easier to understand, uniform safety instructions, symbols, terms and abbreviations were used. The following symbols designate instructions which are not relevant to safety, yet make it easier to understand the operating manual. ^The preconditions for an action are depicted with this symbol. Complete the specied items before carrying out the action steps which follow. cAction steps are designated by this symbol. Carry out the action steps in the order they are presented. (The result of the action or the reaction of the product to the action are depicted with this symbol. •Lists without a mandatory sequence are presented as a list with this bullet.1. Numbered listings are displayed in this manner.(1) Refers to a position in an illustration.Texts in this color designate elements on the app surface.Wherever you see this symbol, you will nd useful information for safe, trouble-free operation of the product.1.3.1 Symbols in illustrationsSymbol ExplanationImage positionAction steps numbered in an illustration.Carry out the action steps in the order they are presented.Only carry out these tasks when using an Apple iPad.Only carry out these tasks when using an Android tablet.1.4 Target groupThis user manual is directed to sound engineers and professional personnel who have detailed expe-rience in the sound and event technology. Personnel who are in training must only work with this device under the supervision of experienced persons.11
6User Manual – XIRIUM PRO® CA | BDA 471 2017/03Safety2 Safety2.1 Warning information and signal wordsSpecial warning information regarding potential dangers inherent in a particular action are presented before instructions for an action. The warnings are ranked as follows: DANGERImmediate threat of danger!This type of warning points out a situation which would result in death or severe injuries. cIf this warning is not heeded, the threat of death or serious injuries is imminent. WARNINGPossible threat of danger!This type of warning points out a situation which could result in death or severe injuries. cIf this warning is not heeded, the threat of death or serious injuries might be imminent. CAUTIONPossible threat of danger!This type of warning points out a situation which could result in minor or moderate injuries. cIf this warning is not heeded, minor injuries may result. NOTICEPossible threat of property damage!This type of warning points out a situation which could result in damage to the device and its components. cIf this warning is not heeded, property damage may result.2.2 Warning symbolsSymbol WarningGeneral warningWarning of hearing impairmentDanger of electric shock
7User Manual – XIRIUM PRO® CA | BDA 471 2017/03Safety2.3 Important regulatory notesThis equipment has been tested and found to comply with the limits for a Class B digital device, pur-suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is en-couraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help. NOTICEThis device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standards.Operation is subject to the following two conditions:1. this device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. REMARQUELe présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes:1. l'appareil ne doit pas produire de brouillage, et 2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. NOTICEChanges or modications made to this equipment not expressly approved by Neutrik may void the FCC and IC authorization to operate this equipment. NOTICEThis device must be professionally installed. NOTICEThis radio transmitter (IC: 11536A-XPT / IC: 11536A-XPR) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.Provided antennas: • NXPA-2-360 (SOA-2456/360/1/0/V; 2 dBi gain) • NXPA-6-360-25 (ECO6-5500-BLK-RN; 6 dBi gain) • NXPA-9-360-12.5 (ECO9-5500-BLK-RN; 9 dBi gain)
8User Manual – XIRIUM PRO® CA | BDA 471 2017/03Safety2.3.1 Radio frequency radiation exposure informationThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environ-ment. This equipment should be installed and operated with minimum distance of 0,65 ft (20 cm) between the radiator and your body.This transmitter must not be co-located or operating in conjunction with any other antenna or trans-mitter.2.4 Important safety instructions WARNINGRisk of fire or electric shock! cTo reduce the risk of re or electric shock, do not expose this device to rain or moisture and do not set any objects containing liquids on this apparatus. WARNINGDanger of fire and explosion due to overheated battery! cDo not expose batteries or battery pack to excessive heat such as re or other heat sources. •To completely disconnect this apparatus from AC mains, disconnect the power supply cord plug from the AC socket. •Keep the mains plug of the power supply cord readily accessible.Avoid property damage to the XIRIUM PRO devices due to unsuitable operating and environmental conditions: •Never immerse in water. •Protect from strong sunlight. •Never install the device near heat sources such as radiators, heating units, ovens or stoves. •Never cover the device, to avoid overheating. •Protect the device from impact and above all, from falling from poles, stages, tables or furniture. •Always set up and fasten the device as shown in Section "5.8.4 Fastening and securing XIRIUM PRO devices" on page 46.Repair DANGERDanger of injury or electric shock and property damage due to improper repair!The XIRIUM PRO devices do not contain any parts which you can repair yourself. Opening or re-pairing the devices on your own can lead to severe damage to the devices and electrical shock or injuries to the operator. cDo not open the housing of XIRIUM PRO devices under any circumstances. cDo not exchange any parts yourself. cOnly have XIRIUM PRO devices repaired by a authorized specialist dealer.
9User Manual – XIRIUM PRO® CA | BDA 471 2017/03SafetyElectrical connection DANGERDanger of electric shock when connecting to or disconnecting from a power grid! cOnly connect the devices to mains sockets installed by authorized electricians. cDo not handle the devices with moist or wet hands under any circumstances. cMake sure the specied mains voltage and mains frequency agree with the values of the power grid. cOnly use the delivered power supply cable for connecting to the socket. cDuring storms or whenever there is a danger of power uctuations, switch off the device and separate from the power grid. cEnsure that the power supply cable is not kinked, hung over sharp edges or allowed to contact hot surfaces during operation. cDo not use the devices if there is interference or damage to the devices, displays or accessories.Information for operation cEnsure that the ambient conditions specied for XIRIUM PRO are observed during operation. cDo not use the XIRIUM PRO devices if they are not functioning properly, have fallen or been damaged, have become wet or if parts of the devices have been immersed in water. cIf disruptions occur during operation: Immediately switch off the XIRIUM PRO devices and disconnect them from the power grid. cDo not operate the XIRIUM PRO devices in environments where ammable or explosive materials, gases or vapors are present or could occur. AVERTISSEMENTRisque d'électrocution! cPour réduire les risques d'incendie ou d'électrocution, ne pas exposer l'appareil à la pluie ni à l'humidité et ne pas déposer d'objet contenant du liquide sur cet appareil. AVERTISSEMENTRisque d'incendie et d'explosion en cas de surchauffe de la pile! cLes batteries ou bloc de batteries ne doivent pas être exposées à une chaleur excessive telle que celle du soleil, feu ou autre source de chaleur similaire. •Pour déconnecter complètement l’appareil du réseau d’alimentation, déconnecter le cordon d’alimentation de la prise murale. •La prise du réseau d’alimentation doit demeurer aisément accessible.Pour éviter les dommages matériels aux appareils XIRIUM PRO causés par des conditions climatiques ou de fonctionnement inadéquates : •Ne jamais l'immerger dans l'eau. •Protéger l'appareil des forts rayons du soleil. •Ne jamais installer l'appareil près de sources de chaleur comme un radiateur, un appareil de chauffage, un four ou un poêle. •Afin d'éviter une surchauffe, ne jamais couvrir l'appareil. •Il faut protéger l'appareil des impacts et surtout l'empêcher de tomber d'une perche, d'une estrade, d'une table ou d'un meuble. •Toujours installer et fixer l'appareil comme illustré dans la section «5.8.4 Fastening and securing XIRIUM PRO devices» on page 42.
10User Manual – XIRIUM PRO® CA | BDA 471 2017/03SafetyRéparation DANGERRisque de blessures, d'électrocution et de dommages matériels en cas de réparations inappropriées!Les appareils XIRIUM PRO ne contiennent aucune pièce pouvant être réparée par l'utilisateur. L'ou-verture ou la réparation des appareils par l'utilisateur peuvent entraîner des dommages graves aux appareils, des blessures ou une électrocution de l'opérateur. cNe pas ouvrir le boîtier des appareils XIRIUM PRO en aucun cas. cL'utilisateur ne doit pas changer de pièces lui-même. cFaire réparer tout appareil XIRIUM PRO uniquement par un détaillant spécialisé autorisé.Branchement électrique DANGERRisque d'électrocution lors du branchement ou du débranchement au réseau électrique! cBrancher seulement l'appareil à des prises de courant installées par des électriciens qualifiés. cNe pas manipuler les appareils avec les mains humides ou mouillées en aucun cas. cS'assurer que la fréquence et la tension du réseau correspondent aux spécifications. cUtiliser seulement le cordon d'alimentation électrique fourni pour brancher l'appareil à la prise de courant. cPendant les tempêtes où lorsqu'il y a des risques de fluctuation de tension, fermer l'appareil et le débrancher du réseau électrique. cS'assurer que le cordon d'alimentation n'est pas plié, suspendu sur une arête tranchante ou en contact avec des surfaces chaudes pendant le fonctionnement. cNe pas utiliser les appareils s'il y a des interférences ou si l'appareil, l'écran ou les accessoires sont endommagés.Informations relatives au fonctionnement cS'assurer que les conditions ambiantes prévues sont respectées pendant le fonctionnement du XIRIUM PRO. cNe pas utiliser les appareils XIRIUM PRO s'ils ne fonctionnent pas adéquatement, s'ils sont tombés ou s'ils sont endommagés ou si des pièces de l'appareil ont été immergées dans l'eau. cSi des perturbations se produisent pendant le fonctionnement : Éteindre immédiatement l'appareil XIRIUM PRO et le débrancher du réseau électrique. cNe faites pas fonctionner l'appareil XIRIUM PRO dans des environnements où des matériaux, des gaz ou des vapeurs inflammables ou explosifs peuvent être présents ou peuvent se produire.2.5 Proper useThe XIRIUM PRO devices are intended for signal transmission between an audio source and an audio sink in accordance with the technical specications.2.6 Foreseeable improper useThe XIRIUM PRO devices are not suitable for use in potentially explosive atmospheres.
11User Manual – XIRIUM PRO® CA | BDA 471 2017/03Components and accessories3 Components and accessories3.1 XIRIUM PRO componentsThe components and accessories are ordered individually.213 1415 1617 181783 41011 1295 6
12User Manual – XIRIUM PRO® CA | BDA 471 2017/03Components and accessories* Quick Start Guide included in scope of delivery.Pos. Description Article no.1 TX base station*(TX base station, XIRIUM PRO USB data cable, ManfrottoTM universal mounting clamp, 5 GHz antenna, 2.4 GHz antenna)NXP2TX-C2 RX base station*(RX base station, XIRIUM PRO USB data cable, ManfrottoTM universal mounting clamp, 2.4 GHz antenna)NXP2RX-C3TX modules •TX module analog* •TX module AES* •TX module DANTE*NXP-TM-ANANXP-TM-AESNXP-TM-DANTE4RX modules •RX module analog* •RX module AES* •RX module DANTE* •Repeater module*NXP-RM-ANANXP-RM-AESNXP-RM-DANTENXP-RM-RP5 5 GHz antenna 9 dBi 360°H 12.5°V NXPA-9-360-12.565 GHz antenna 6 dBi 360°H 25°V NXPA-6-360-2575 GHz directional antenna 14 dBi 40°H 35°V, including adapter to mount the antenna directly on a receiver if no repeater module is inserted!NXPA-14-40-358 2.4 GHz omnidirectional antenna for connecting app NXPA-WIFI9 5 GHz directional antenna (for remte setup) 18 dBi 18°H 18°V, for receiver if no repeater module is inserted! (cable not included!)NXPA-18-18-1810 5 GHz omnidirectional antenna 2 dBi 360°H 360°V, for repeater setups with different antenna heights (see page 26)NXPA-2-36011 Antenna cable S04162B, N type connectors, 5 m, 4 dB attenuation NKXPA-512 N Adapter female female, for remote TX antenna (cable not icluded!) NXPA-N-FF13 ManfrottoTM universal mounting clamp NXUC-M-1514 Mounting arm for XIRIUM PRO antennas (NXPA-14-14-35, NXPA-18-18-18, NX-6-360-25), compatible with ManfrottoTM clampNXPMA15 Power cable XIRIUM PRO, 3 m NKXPF-5-15-316 XIRIUM PRO data cable NKXP-DATA17 Flight case with foam cut-outs to hold 2x base stations (not included) CAS-NXP18 Hard case (trolley) with foam cut-outs to hold 3 devices (not included) CAS-NXP-T* Power cables have to be ordered seperately!
13User Manual – XIRIUM PRO® CA | BDA 471 2017/03Description of product11667822Pos. Designation15 GHz antenna connector with 5 GHz antennaThe antenna transmits the signals between the XIRIUM PRO devices.22.4 GHz antenna connector (reverse SMA) with 2.4 GHz antennaTransmits control data via WIFI3Housing Extruded aluminum housing4LugSafety lug for additional fall arresting5BoltAdapter for mounting with a ManfrottoTM clamp6On/off switch Powering the device ON/OFF, LED indicationLED display: •LED off: Device off or powering up. •LED solid green: Device powerd-on and battery level is between 20 % and 100 %. •LED slow-ash green: Device powerd-on and battery is charging. •LED solid red: Firmware update active. •LED slow-ash red: Device identication activated from app by pressing the Identify Device button. •LED quick-ash red: Battery below 20 %.4 Description of product4.1 XIRIUM PRO base stationON/OFF LINK push 1sXROC push 4sON/OFF LINK push 1sDELAY push 4sON/OFF LINK push 1sXROC push 4sON/OFF LINK push 1sDELAY push 4sTX, top viewBottom viewRX, top viewPos. Designation7TX link buttonLinking devices, switching XROC mode ON/OFF, resetting transmission power •Push and release: Start/stop LINK process •Hold 4 sec: Toggle XROC mode ON/OFF •Hold 8 sec: Reset transmission powerLED display: •LED off: TX not transmitting audio signal. •LED solid blue: TX transmitting audio signal. •LED quick-ash blue: Device is activated for linking process. •LED slow-ash blue: XROC mode set to ON.8RX link buttonLinking devices; switching delay ON/OFF •Push and release: Start/stop LINK process •Hold 4 sec: Toggle delay ON/OFF •Hold 8 sec: Reset repeater transmission power LED display: •LED off: RX not receiving audio signal. •LED solid blue: RX receiving audio signal. •LED quick-ash blue: Device is activated for linking process. •LED slow-ash blue: Delay set to ON.9Type plateWith serial number, SSID and WLAN password10 D-Sub connector Interface between base station and module.11 USB portUSB connection for rmware updateAESRXLIECHTENSTEIN OUT 1 3 2EBU/RXLIECHTENSTEIN LINE OUT 1 (XROC) OUT 2 1 3 2 1 3 2DANTE C6 ARXLIECHTENSTEIN OUT C6 ATXLIECHTENSTEIN IN AES1 2 3 EBU/PUSH DANTE C6 ATXLIECHTENSTEIN INC6 AREPEATER RXLIECHTENSTEIN TXLIECHTENSTEIN IN 2 IN 1 (XROC) LINE1 2 3 PUSH 1 2 3 PUSH 100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz1234510911
14User Manual – XIRIUM PRO® CA | BDA 471 2017/03Description of product4.2 ModulesTX AES moduleRX DANTE moduleRX analog moduleRepeater moduleRX AES moduleTX DANTE moduleTX analog moduleTop view Bottom view4.2.2 RX modules4.2.1 TX modulesAESRXLIECHTENSTEIN OUT 1 3 2EBU/RXLIECHTENSTEIN LINE OUT 1 (XROC) OUT 2 1 3 2 1 3 2DANTE C6 ARXLIECHTENSTEIN OUT C6 ATXLIECHTENSTEIN IN AES1 2 3 EBU/PUSH DANTE C6 ATXLIECHTENSTEIN INC6 AREPEATER RXLIECHTENSTEIN TXLIECHTENSTEIN IN 2 IN 1 (XROC) LINE1 2 3 PUSH 1 2 3 PUSH 100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60HzAESRXLIECHTENSTEIN OUT 1 3 2EBU/RXLIECHTENSTEIN LINE OUT 1 (XROC) OUT 2 1 3 2 1 3 2DANTE C6 ARXLIECHTENSTEIN OUT C6 ATXLIECHTENSTEIN IN AES1 2 3 EBU/PUSH DANTE C6 ATXLIECHTENSTEIN INC6 AREPEATER RXLIECHTENSTEIN TXLIECHTENSTEIN IN 2 IN 1 (XROC) LINE1 2 3 PUSH 1 2 3 PUSH 100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60HzAESRXLIECHTENSTEIN OUT 1 3 2EBU/RXLIECHTENSTEIN LINE OUT 1 (XROC) OUT 2 1 3 2 1 3 2DANTE C6 ARXLIECHTENSTEIN OUT C6 ATXLIECHTENSTEIN IN AES1 2 3 EBU/PUSH DANTE C6 ATXLIECHTENSTEIN INC6 AREPEATER RXLIECHTENSTEIN TXLIECHTENSTEIN IN 2 IN 1 (XROC) LINE1 2 3 PUSH 1 2 3 PUSH 100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60HzAESRXLIECHTENSTEIN OUT 1 3 2EBU/RXLIECHTENSTEIN LINE OUT 1 (XROC) OUT 2 1 3 2 1 3 2DANTE C6 ARXLIECHTENSTEIN OUT C6 ATXLIECHTENSTEIN IN AES1 2 3 EBU/PUSH DANTE C6 ATXLIECHTENSTEIN INC6 AREPEATER RXLIECHTENSTEIN TXLIECHTENSTEIN IN 2 IN 1 (XROC) LINE1 2 3 PUSH 1 2 3 PUSH 100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60HzAESRXLIECHTENSTEIN OUT 1 3 2EBU/RXLIECHTENSTEIN LINE OUT 1 (XROC) OUT 2 1 3 2 1 3 2DANTE C6 ARXLIECHTENSTEIN OUT C6 ATXLIECHTENSTEIN IN AES1 2 3 EBU/PUSH DANTE C6 ATXLIECHTENSTEIN INC6 AREPEATER RXLIECHTENSTEIN TXLIECHTENSTEIN IN 2 IN 1 (XROC) LINE1 2 3 PUSH 1 2 3 PUSH 100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60HzAESRXLIECHTENSTEIN OUT 1 3 2EBU/RXLIECHTENSTEIN LINE OUT 1 (XROC) OUT 2 1 3 2 1 3 2DANTE C6 ARXLIECHTENSTEIN OUT C6 ATXLIECHTENSTEIN IN AES1 2 3 EBU/PUSH DANTE C6 ATXLIECHTENSTEIN INC6 AREPEATER RXLIECHTENSTEIN TXLIECHTENSTEIN IN 2 IN 1 (XROC) LINE1 2 3 PUSH 1 2 3 PUSH 100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60HzAESRXLIECHTENSTEIN OUT 1 3 2EBU/RXLIECHTENSTEIN LINE OUT 1 (XROC) OUT 2 1 3 2 1 3 2DANTE C6 ARXLIECHTENSTEIN OUT C6 ATXLIECHTENSTEIN IN AES1 2 3 EBU/PUSH DANTE C6 ATXLIECHTENSTEIN INC6 AREPEATER RXLIECHTENSTEIN TXLIECHTENSTEIN IN 2 IN 1 (XROC) LINE1 2 3 PUSH 1 2 3 PUSH 100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60HzAESRXLIECHTENSTEIN OUT 1 3 2EBU/RXLIECHTENSTEIN LINE OUT 1 (XROC) OUT 2 1 3 2 1 3 2DANTE C6 ARXLIECHTENSTEIN OUT C6 ATXLIECHTENSTEIN IN AES1 2 3 EBU/PUSH DANTE C6 ATXLIECHTENSTEIN INC6 AREPEATER RXLIECHTENSTEIN TXLIECHTENSTEIN IN 2 IN 1 (XROC) LINE1 2 3 PUSH 1 2 3 PUSH 100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60HzAESRXLIECHTENSTEIN OUT 1 3 2EBU/RXLIECHTENSTEIN LINE OUT 1 (XROC) OUT 2 1 3 2 1 3 2DANTE C6 ARXLIECHTENSTEIN OUT C6 ATXLIECHTENSTEIN IN AES1 2 3 EBU/PUSH DANTE C6 ATXLIECHTENSTEIN INC6 AREPEATER RXLIECHTENSTEIN TXLIECHTENSTEIN IN 2 IN 1 (XROC) LINE1 2 3 PUSH 1 2 3 PUSH 100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60HzAESRXLIECHTENSTEIN OUT 1 3 2EBU/RXLIECHTENSTEIN LINE OUT 1 (XROC) OUT 2 1 3 2 1 3 2DANTE C6 ARXLIECHTENSTEIN OUT C6 ATXLIECHTENSTEIN IN AES1 2 3 EBU/PUSH DANTE C6 ATXLIECHTENSTEIN INC6 AREPEATER RXLIECHTENSTEIN TXLIECHTENSTEIN IN 2 IN 1 (XROC) LINE1 2 3 PUSH 1 2 3 PUSH 100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz100-240V~ 0.5A 50-60Hz1233 1 564Pos. Description1D-Sub connector interface between base station and module2Module with integrated battery3Locking bolt4LED charging indicator •Flashes green: Battery charging. •Lit green: Battery fully charged.Pos. Description5Audio IN (TX), audio OUT (RX)(different connections depending on module)6powerCON TRUE1 chassis for XIRIUM PRO power cable

Navigation menu