Netgear orporated 12300208 Universal Dual Band Wi-Fi Extender User Manual

Netgear Incorporated Universal Dual Band Wi-Fi Extender Users Manual

Contents

Users Manual

350 East Plumeria DriveSan Jose, CA 95134USAJuly 2013Universal Dual Band WiFi Extender WN3500RP – Wallplug EditionUser ManualNote: This document is for certification purposes.
2Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition SupportThank you for selecting NETGEAR products. After installing your device, locate the serial number on the label of your product and use it to register your product at https://my.netgear.com. You must register your product before you can use NETGEAR telephone support. NETGEAR recommends registering your product through the NETGEAR website. For product updates and web support, visit http://support.netgear.com.Phone (US & Canada only): 1-888-NETGEAR.Phone (Other Countries): Check the list of phone numbers at http://support.netgear.com/general/contact/default.aspx.TrademarksNETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change without notice. © NETGEAR, Inc. All rights reserved.
3ContentsChapter 1 Getting StartedHow the Extender Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6When to Use Your Extender. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6Hardware Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8Buttons and Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Insert the AC Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10Attach the Stand and Power Adapter Cord . . . . . . . . . . . . . . . . . . . . . .11Cable Equipment to the Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Install the Extender. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12Position the Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Extender Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Music Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Chapter 2 Extender Network SettingsLog In to the Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17Use NETGEAR genie After Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .18Add a WPS Client to the Extender WiFi Network. . . . . . . . . . . . . . . . . . . .20Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20Connect the Extender to an Existing Wireless Network . . . . . . . . . . . . .20Extender Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21Extender IP Address Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24Maintenance Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25Status Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Attached Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27Back Up and Manage Extender Settings . . . . . . . . . . . . . . . . . . . . . . . .27Set the Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28Upgrade the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29Advanced Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29Advanced Wireless Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29ReadySHARE Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31FastLane Technology. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32Chapter 3 TroubleshootingFrequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34Connecting to http://www.mywifiext.net . . . . . . . . . . . . . . . . . . . . . . . . . . .35Joining WiFi Networks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
4Universal Dual Band WiFi Extender WN3500RP – Wallplug EditionAppendix A Supplementary InformationFactory Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38Appendix B Notification of Compliance
511. Getting StartedThis chapter covers the following topics: •How the Extender Works •Hardware Features •Install the Extender •Position the Extender •Extender Performance •Music Playback For more information about the topics covered in this manual, visit the support website at http://support.netgear.com.
Getting Started6Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition How the Extender WorksThe extender works like a bridge between a WiFi router and a computer or wireless device outside the wireless router’s range. The extender has two main jobs:1. The extender connects to a WiFi network. When the extender connects wirelessly to a network, it acts as a network client. This is similar to how a computer connects to a network. 2. The extender acts as an access point for computers. The extender has its own wireless network called NETGEAR_EXT that wireless computers can join. In its role as an access point, the extender performs tasks that wireless routers do, such as broadcasting its network name (SSID).The extender needs to do each of these jobs so that both ends of the bridge are in place.The extender is halfwaybetween the routerand the computer.Figure 1. Range extender in a homeWhen to Use Your ExtenderNETGEAR recommends that you connect to the extender only when your home network connection is poor. Because data traffic routed through the extender is inherently slower than traffic routed directly from the network, the computer should stay on the network if the connection is good enough. NETGEAR recommends that you connect through the extender network only when the computer is in a “dead zone” where connection from the network is very poor or non-existent.
Getting Started7 Universal Dual Band WiFi Extender WN3500RP – Wallplug EditionThe extender LEDs can help you tell if the extender is correctly set up and working as it should.•The best performance is delivered when the Link Rate LED or and the Wireless Device to Extender LED are green.•A workable performance is delivered when the Link Rate LED is amber and the Wireless Device to Extender LED is green.Hardware FeaturesThe following sections describe the hardware features of the extender.Package ContentsYour box should contain the items shown in the following figure.ExtenderStandPower adapter cord AC plugFigure 2. Package contents for the extender
Getting Started8Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition LEDsThe LEDs show how the extender is working.WPS Link Rate 2.4 GHzWireless Device to ExtenderLink Rate 5 GHzPower On/OffFigure 3. Extender front panelThe following table describes the LEDs.Table 1. LED DescriptionLED DescriptionPower •On. Power is supplied to the extender.•Off. Power is not supplied to the extender.Link Rate Indicates a 2.4 GHz or 5 GHz wireless connection between the extender and a router. The LED turns on to indicate the type of connection:•Green is best.•Amber is good.•Red is poor.• Off. Not connected to router.Wireless Device to ExtenderThis LED is solid green when the extender is connected to a wireless device.WPS This LED indicates a WPS wireless connection.•Solid green. There is wireless security (WPA or WPA2).•Blinking green. A WPS connection is in progress.• Off. No wireless security.
Getting Started9 Universal Dual Band WiFi Extender WN3500RP – Wallplug EditionButtons and PortsThe following figure shows the buttons and ports on the extender.PowerWPSEthernet portUSB portReset Factory DefaultsAudio portOn/OfFigure 4. Extender side and bottom panels.The Power On/Off button and WPS button are on the side panel.•Power On/Off button. Use this button to turn on and off the extender.•WPS button. Use this button to connect the extender to your existing WiFi network. For more information, see Add a WPS Client to the Extender WiFi Network on page 20.The ports and Reset factory settings button are on the bottom panel.•Audio port. Use the Audio port to connect the extender to your speaker.•USB port. Use the USB port to connect the extender to a printer.•Reset factory settings button. To reset the extender to its original factory settings, insert a paper clip into the reset hole and hold it until the Power LED flashes.•Ethernet port. Use the Ethernet port on the extender to connect an Ethernet-enabled device wirelessly to your network.
Getting Started10Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition Insert the AC PlugYou can use the AC plug to plug the extender directly into an outlet, or you can attach the stand and plug in the power adapter cord (see Attach the Stand and Power Adapter Cord on page 11).123Figure 5. If you want to plug the extender directly into an outlet, insert the AC plug.To insert the AC plug:1. Slide the tab on the top of the AC plug into the open position.2. Align the AC plug with the extender as shown.3. Press firmly so that the AC plug is securely attached to the extender.You can now plug the extender into an electrical outlet.
Getting Started11 Universal Dual Band WiFi Extender WN3500RP – Wallplug EditionAttach the Stand and Power Adapter CordThe extender comes with a stand and power adapter cord. You can attach them as shown if you do not want to plug the extender directly into an outlet.123Figure 6. Attach the stand and the power adapter cord.To attach the stand and power adapter cord:1. Slide the stand onto the extender as shown.2. Turn the adapter so that you can see the side with the power adapter input.3. Connect the power adapter cord to the extender.You can now plug the other end of the power adapter cord into an electrical outlet.Cable Equipment to the PortsYou can connect computers or other devices to the USB port and the Ethernet port on the extender,CAUTION:Do not connect the extender to a router using an Ethernet port. If you do so, the extender does not work because it is designed to use only a WiFi connection to the router.
Getting Started12Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition To cable a computer to the extender:1. Locate the ports on the extender.Ethernet portUSB port2. Use an Ethernet cable or USB cable to connect your computer the extender.3. Plug in the AC adapter or attach the stand and power adapter cord to the extender, and then plug it into an electrical outlet.If you want to log in to the extender, see Log In to the Extender on page 17.To use the extender as a one-port WiFi adapter:1. Make sure that the extender is connected to your existing wireless WiFi network.2. Plug the Ethernet cable from your Ethernet-enabled device (connected TV, Blu-ray player, gaming console) to the Ethernet port of the extender.Install the ExtenderTo install the extender:1. Either connect the AC plug, or attach the stand and the power adapter cord.2. Find a place to install the extender that is about halfway between the router and the computer or wireless device that is outside of the range of the router.DO DON’TIf you have to use a different location, see Position the Extender on page 14.3. Power up the extender.•If you connected the AC plug to the extender, plug it directly into an electrical outlet.•If you attached the stand and power adapter, plug the power adapter into an electrical outlet.
Getting Started13 Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition4. Wait until the Power LED turns green.5. Use a computer or wireless device to connect to the extender. During installation, it might be easier to use a computer or device that is in the same room as the extender.•For a wired connection, connect your computer or wireless device to the extender with an Ethernet cable.•For a wireless connection, use a WiFi network manager to find and connect to NETGEAR_EXT (the SSID) wireless network.Tip: You can use any WiFi network manager utility on a computer or tablet to find and connect to the extender wireless network.After the connection with the computer is established, the Wireless Device to Extender LED turns green. 6. On your computer or wireless device, launch an Internet browser.The browser displays the genie screen.If you do not seethe genie screen, type http://www.mywifiext.net in the address field of your browser.The genie scans for wireless networks in your area.7. Follow the genie steps to set up the extender to work with your network and to set up your computer or wireless device to connect to the extender network. These steps are explained in Use NETGEAR genie After Installation on page 18.
Getting Started14Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition Position the ExtenderThe best connection is established when there is a clear line of sight between the extender and the router and between the extender and the computer or wireless device. If this straight path is blocked by a thick wall or other materials, move the extender to a different location half-way between the computer and the router. If the Link Rate LED is green or amber and the Wireless Device to Extender LED is green, the extender is working as expected.To place the extender and apply power:1. Place the extender an equal distance between your router and the wireless device located outside the range of your router.2. Plug the extender into an electrical outlet, and wait 1 minute until the Power LED turns green. •If you have to use a different location, move the extender closer to the device, but still within the wireless range of the router. •During installation, you can put the extender in the same room as the router. After you complete installation, you can move the extender to a location that is halfway between the router and your computer, and still displaying a green link rate.To improve the Link Rate LED from red or amber to green:1. If the Link Rate LED is red, move the extender closer to the router or to a different spot where it provides a better line of sight.2. As you move the extender, check the LEDs until you find a location where the Link Rate LED is green or amber, and the Wireless Device to Extender LED is green. 3. You might have to unplug the extender as you move it to a different location. If you do, from the new location, power up the extender and continue to check the LEDs.Once the LEDs show that the extender is in a good location, open a browser and go to http://www.mywifiext.net to continue the setup process.
Getting Started15 Universal Dual Band WiFi Extender WN3500RP – Wallplug EditionExtender PerformanceThe Link Rate LEDs indicate the performance of the 2.4 GHz or 5 GHz wireless connection from the extender to a router. •The best performance is delivered when the Link Rate LED is green. •A workable performance is delivered when the Link Rate LED is amber.•A red Link Rate LED indicates a poor connection or no connection between the extender and the router.•Make sure that your Wireless Device to Extender LED is green before you check the Link Rate LED for performance.To improve extender performance:1. Move the extender closer to the router or to a different location with a better line of sight. 2. As you move the extender, check the Link Rate and the Wireless Device to Extender LEDs on the extender until you find a good location. These LEDs should remain solid green.Music PlaybackThe extender supports the DLNA DMR function, which means you can stream your network music and play it back through the extender audio jack.•Windows 7 users can use Windows Media Player (WMP) to play back music.•Android phone, iPhone, or iPad users can download NETGEAR genie to play back music (go to http://www.netgear.com/genie).•DLNA DMR supports mp3, wave. flac, and aac file formats.•The 3.5 mm stereo port supports earphones and powered speakers.
1622. Extender Network SettingsThis chapter covers the following topics: •Log In to the Extender •Add a WPS Client to the Extender WiFi Network •Setup Menu •Maintenance Settings •Advanced Settings
Extender Network Settings17 Universal Dual Band WiFi Extender WN3500RP – Wallplug EditionLog In to the ExtenderYou can log in to the extender to use NETGEAR genie or to use the menu selections to view or change the extender’s settings. To log in:1. Launch an Internet browser such as Mozilla Firefox or Microsoft Internet Explorer. 2. In the address field of your browser, enter http://www.mywifiext.net. You are prompted to enter a user name and password.If you do not see the log in prompt, make sure to include http:// when you type http://www.mywifiext.net in your browser.3. Type admin for the user name. The default password is password. NETGEAR recommends that you set a more secure password after you log in (see Set the Password on page 28).•If your extender has an Internet connection, the Firmware Upgrade screen displays (see Upgrade the Firmware on page 29), and the software checks for new firmware at the NETGEAR website. •The Status screen displays with the menu on the left. This screen shows what the current settings are for the extender.If you have trouble connecting:•If you connect an Ethernet cable to the extender, and launch your browser quickly, the computer might still need a couple of minutes to recognize the Ethernet LAN connection before you can connect. •Make sure that your Ethernet cable is securely connected to the extender and the computer, and that the extender LAN LED is on. If the LED is not lit, reconnect the Ethernet cable, and relaunch your Internet browser.
Extender Network Settings18Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition Use NETGEAR genie After InstallationNETGEAR genie can help you set up your extender to connect to a wireless network. For information about more configuration options, see Chapter 2, Extender Network Settings.The installation guide (included in the package) explains how to install your extender. During installation, when you launch your Internet browser, NETGEAR genie automatically displays. After installation, to use genie again: 1. Log in to the extender.Note: Once you begin using genie, you have to complete all of its steps before you can exit.2. Select Setup Wizard. The software detects wireless networks in your area and displays a list:3. Either select a network from the list, or select the Manually input my wireless SSID radio button and type the SSID.
Extender Network Settings19 Universal Dual Band WiFi Extender WN3500RP – Wallplug EditionIf the network is secure, you are prompted to enter the passphrase (network password):4. Enter the password for your wireless network and click Continue. The genie sets up a WiFi connection from the extender to the router, which takes about 2 minutes. Then the following screen displays.5. Review the settings, and make sure that they are correct. Then, click Continue.The Device-to-Extender settings are applied, which takes about 2 minutes. Then the following screen displays..6. Join the extender network with your wireless computer or device.7. Select the check box. 8. Click Continue.
Extender Network Settings20Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition Add a WPS Client to the Extender WiFi NetworkWPS (Wi-Fi Protected Setup) lets you join a secure WiFi network without typing its password. Instead, you use a WPS button or enter a PIN to connect. WPS supports WPA and WPA2 wireless security.Note: You cannot use the Push 'N' Connect WPS button on the extender to connect the extender to your wireless network. The WPS button on the extender can be used only to connect a computer to the extender. To join the extender’s network using WPS:1. Select Add WPS Client. The following screen displays:2. Select a radio button.•Push Button (recommended). Either click the button or press the WPS button on the front of the extender.•PIN Number. Select the radio button, and a PIN displays.The extender tries to find the wireless client (the computer) that is attempting to join the network. If you are using a WPS button, it tries for 2 minutes. If you are using a PIN, it tries for 4 minutes.3. Go to your wireless computer. Use its WPS software to try to connect to the extender.Setup MenuConnect the Extender to an Existing Wireless NetworkYou can wirelessly connect the extender to your home network.
Extender Network Settings21 Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition1. Select Setup > Connect to an Existing Network. The extender scans for wireless networks, and displays a list.If your wireless network is not on the list, the extender might be too far away from the router. See Position the Extender on page 14 for suggestions.2. Select the radio button for your network, and click Continue. If you selected the manual option, you are prompted to type the network name (SSID) and to enter the password to access it:3. Enter your network’s password or key, and click Continue. The extender joins your wireless network.Extender Wireless SettingsYou can use the Wireless Settings screen to change the network name (SSID) for the extender’s network and to set up wireless security. If you do not change these settings, the network name is NETGEAR_EXT, and the network is open (no wireless security is set up).Note: If you use a wireless computer to change the extender’s wireless settings, you will be disconnected when you click Apply. To reconnect, you have to select the new network name that you created, and enter its password or wireless security key.
Extender Network Settings22Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition To change the wireless settings for the extender’s network:1. Select Setup > Wireless Settings to display the following screen:2. In the Name (SSID) field, you can type in a new name to customize your extender network. This will make it easier to identify your extender if more than one is operating in your neighborhood.3. In the Security Options section of the screen, select the type of wireless security that you want to use on your network.•None. This is an open wireless network. Any wireless computer or device is allowed to join this network.•WEP. WEP is an older standard, and is less secure than WPA or WPA2. WEP uses encryption keys and data encryption for data security. You can select 64-bit or 128-bit encryption.•WPA-PSK [TKIP]. WPA is more secure than WEP. When using wireless computers or devices that support WPA, you can enter a passphrase to join the extender’s wireless network.•WPA2-PSK [AES]. WPA2 is even more secure, but some older computers do not support this standard. When using wireless computers or devices that support WPA2, you can enter the passphrase to join the extender’s wireless network.•WPA-PSK [TKIP] + WPA2-PASK [AES]. When using wireless computers or devices that support either WPA or WPA2, you can enter the passphrase to join the extender’s wireless network.4. Click Apply to save your settings.5. Use your wireless computer to connect to the extender’s network with its new settings. The Smart Wizard can guide you through this process.
Extender Network Settings23 Universal Dual Band WiFi Extender WN3500RP – Wallplug EditionSet Up WPA, WPA2, or WPA + WPA2Both WPA and WPA2 provide strong data security. WPA with TKIP can be used on Windows systems with Service Pack 2 or later. WPA2 with AES is a hardware implementation; see your device documentation before implementing it. To configure WPA or WPA2 in the extender:1. On the Wireless Setting screen, select the radio button for the WPA or WPA2 option of your choice.2. The settings displayed on the screen depend on which security option you select.3. For WPA-PSK or WPA2-PSK, enter the passphrase. 4. Click Apply to save your settings.Set Up WEPWEP is a legacy wireless security setting. NETGEAR recommends that you use a newer standard such as WPA2 or WPA unless you have older wireless equipment that supports only WEP.To set up WEP:1. In the Wireless Settings screen, in the Security Options section, select the WEP radio button.2. Select the authentication type: Automatic, Open System, or Shared Key. The default is Open System.Note: The authentication is separate from the data encryption. You can select authentication that requires a shared key, but still leaves data transmissions unencrypted. Security is stronger if you use both the Shared Key and WEP encryption settings.3. Select the encryption strength setting:•WEP 64-bit encryption. Enter 10 hexadecimal digits (any combination of 0–9, a–f, or A–F).•WEP 128-bit encryption. Enter 26 hexadecimal digits (any combination of 0–9, a–f, or A–F).4. Enter the encryption keys. You can manually or automatically program the four data encryption keys. These values have to be identical on all computers and access points in your network:•Passphrase. To use a passphrase to generate the keys, enter a passphrase, and click Generate to create the keys to access the extender network.
Extender Network Settings24Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition Note: Not all wireless computers support passphrase key generation. If your computer does not support the passphrase, then you will need to type the encryption key in order to join the wireless network. •Key 1–Key 4. These values are not case-sensitive. You can manually enter the four data encryption keys. These values have to be identical on all computers and access points in your network. Enter ten hexadecimal digits (any combination of 0–9, a–f, or A–F).5. Select which of the four keys will be the default. Data transmissions are always encrypted using the default key. The other keys can be used only to decrypt received data. The four entries are disabled if WPA-PSK or WPA authentication is selected. 6. Click Apply to save your settings.Extender IP Address SetupThe IP Address Setup screen shows whether the extender is set to get its IP address dynamically from the router (this is the most common setting), or is set up with a static IP address.To view or change the IP address settings:Select Setup > IP Address Settings. The following information is displayed:•Get Dynamically IP Address From Router. The wireless network router assigns an IP address when the extender connects to its wireless network. Most networks are set up so that the router automatically does this.•Use Static IP Address. Specify a static IP address. This is not usually necessary. If you set this up, you should be technically experienced or have a technically experienced person help you.- IP Address. The static IP address.- IP Subnet Mask. The subnet mask associated with the IP address.
Extender Network Settings25 Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition- Gateway IP Address. The IP address for the gateway.- Primary DNS. The primary Domain Name Server (DNS).- Secondary DNS. The secondary Domain Name Server (DNS).Maintenance SettingsYou can use the maintenance settings to view the extender status, view attached devices, back up and restore configuration settings, set the password, and update the firmware.Status ScreenWhen you connect to http://www.mywifiext.net, after the automatic firmware check, the Status screen displays. You can also select Status from the menu to display this screen:This screen shows the current settings and the status of your extender.You can click Show Statistics to see device performance statistics such as the number of packets sent and number of packets received for each port. See Show Statistics on page 26.The following fields are displayed in the Status screen:•Hardware Version. The hardware version of the extender.•Firmware Version. The current firmware version of the extender. If you upgrade the firmware, this field changes.•GUI Language Version. The language version running on the extender. If you upgrade the firmware, this field changes.Connection Status to Existing Network•Name (SSID). Your extender is set up to connect to this SSID, also called the wireless name.
Extender Network Settings26Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition •Connection Status. The status of your wireless connection (connected or disconnected).•Link Rate. The actual transmission (Tx) and receive (Rx) link rate in the current wireless connection.Extender IP Info•MAC Address. The physical address of the extender, as seen from the local area network (LAN).•IP Address. The IP address of the extender. The default is 192.168.1.250.•DHCP Server. Identifies the network DHCP server on the wireless network.•IP Subnet Mask. The IP subnet mask associated with the LAN IP address of the extender. The default is 255.255.255.0.•Gateway IP Address. The IP address of the wireless network gateway.•Domain Name Server. The IP address of the Domain Name Server (DNS) of the wireless network.Extender Wireless Settings•Name (SSID). The name (SSID) of the wireless network.•Region. The location where the extender is operating.•Channel. The channel of the wireless network.•Wireless AP. On or Off.•Broadcast Name. On or Off.•Wi-Fi Protected Setup. Configured.Show StatisticsScroll to the bottom of the Status screen, and click Show Statistics. The following screen displays:The screen shows statistics for the LAN (local), and wireless LAN (WLAN) ports. For each port, the screen displays the following:
Extender Network Settings27 Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition•Status. The status of the port.•TxPkts. The number of packets transmitted on this port since reset or manual clear.•RxPkts. The number of packets transmitted on this port since reset or manual clear.•Collisions. The number of collisions on this port since reset or manual clear.•Tx B/s. The current line utilization—percentage of current bandwidth used on this port.•Rx B/s. The average line utilization for this port.•Up Time. The time elapsed since the last power cycle or reset.•Poll Interval. Specify the poll interval frequency. If you change this value, click Set Interval so that your change takes effect.Attached DevicesSelect Maintenance > Attached Devices to display the following screen:Back Up and Manage Extender SettingsYou can save and retrieve a file containing your extender configuration settings. Once you have your extender working correctly, you should back up the information to have it available if something goes wrong. When you back up the settings, they are saved as a file on your computer. You can restore the device’s settings from this file.To back up settings:1. Select Maintenance > Backup Settings to display this screen.2. Click Backup. Your browser extracts the configuration file from the extender.3. If you do not have your browser set up to save downloaded files automatically, locate where you want to save the file. 4. You can give the file a meaningful name at this time, such as internet_adapter.cfg.
Extender Network Settings28Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition To restore settings:1. On the Backup Settings screen, click Browse.2. Locate and select the previously saved backup file.3. Click Restore.A screen displays letting you know that the device has been successfully restored to the previous settings. The extender restarts, which takes about 1 minute.CAUTION:Do not try to go online, turn off the extender, shut down the computer, or do anything else to the extender until it finishes restarting! 4. Close the message window.To erase settings:Under some circumstances (for example, if you have lost track of the changes that you made to the extender settings), you might want to erase the configuration. After an erase, the extender returns to its factory settings (see Factory Settings on page 37).To erase the configuration, click the Erase button in the Backup Settings screen. The extender automatically shuts down and reboots with its factory settings.CAUTION:Do not try to go online, turn off the extender, shut down the computer, or do anything else to the extender until it finishes restarting! Set the PasswordThe user name to access the extender is admin, and its default password is password. NETGEAR strongly recommends that you set a more secure password.To set the password:1. Select Maintenance > Set Password. The following screen displays:2. Type the old password, type the new password twice, and then click Apply.
Extender Network Settings29 Universal Dual Band WiFi Extender WN3500RP – Wallplug EditionUpgrade the FirmwareUnless you changed the settings in the Firmware Upgrade screen previously, the extender is set up to check for new firmware automatically at log in.If you do not want to use the automatic firmware check, clear the Check for New Version Upon Login check box.To check for firmware and upgrade if it is available:1. Select Maintenance > Firmware Update. The following screen displays:2. Click Check to see if new firmware is available. If it is, follow the onscreen prompts to download it onto your computer.3. In the Browse field, enter the path for the new firmware, or click Browse to locate and select the file.4. Click Upload to install the new firmware on your extender.CAUTION:Once you start the firmware upgrade, do not try to go online, turn off the extender, shut down the computer, or do anything else to the extender until it finishes restarting! Advanced SettingsYou can view or change advanced wireless settings, ReadySHARE printer settings, and FastLane™ technology settings.Advanced Wireless SettingsThe extender is already configured with the optimum settings. Do not alter these settings unless you have a specific reason to do so. Incorrect settings might disable the extender unexpectedly.
Extender Network Settings30Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition To view or change the advanced wireless settings:Select Advanced > Wireless Settings. The following screen displays:You can view or configure the following settings:•Advanced Wireless Settings-Enable Wireless Access Point (2.4 GHz). Enable the extender to work as a wireless access point. If this check box is cleared, then computers or wireless devices cannot connect wirelessly to the extender.-Enable SSID Broadcast (2.4 GHz). Enable the extender to broadcast its wireless network name (SSID). If this check box is cleared, then the wireless network is hidden. To join a hidden wireless network, you have to type the wireless name.-Enable Wireless Access Point (5 GHz). Enable the extender to work as a wireless access point. If this check box is cleared, then computers or wireless devices cannot connect wirelessly to the extender.-Enable SSID Broadcast (5 GHz). Enable the extender to broadcast its wireless network name (SSID). If this check box is cleared, then the wireless network is hidden. To join a hidden wireless network, you have to type the wireless name.•WPS Settings-Disable Device’s PIN. Selecting this check box disables the extender’s PIN. The PIN can be used for a WPS wireless connection.-Keep Existing Wireless Settings. When this check box is selected, the settings in the Wireless Settings screen stay the same when WPS is used for a wireless connection.•Wireless Card Access List. Specify a list of computers or wireless devices that are allowed to connect to the network. If you use an access list, then computers that are not on the list are not allowed to join the wireless network.To set up a wireless card access list:1. On the Advanced Wireless Settings screen, click Setup Access List.
Extender Network Settings31 Universal Dual Band WiFi Extender WN3500RP – Wallplug EditionThe following screen displays:2. Select the Turn Access Control On check box.3. Add the computers and wireless devices that you want to give access to the network.•Click the Add button for each device.•If you are not sure of the MAC address, check the product label.•Make sure to add the computer or wireless device that you are currently using.4. Click Apply so that your changes take effect.ReadySHARE PrinterReadySHARE Printer lets you connect a USB printer to the extender’s USB port, and access it wirelessly.To enable ReadySHARE Printer:1. Connect the USB printer to the extender’s USB port with a USB printer cable.2. Install the USB printer driver software on each computer that will share the printer. If you do not have the printer driver, contact the printer manufacturer to find and download the most recent printer driver software.3. On each computer that will share the printer, download the NETGEAR USB Control Center utility. The NETGEAR USB utility has a Mac version and a Windows version, which you can access from the ReadySHARE Printer area of the page you access using this URL: www.netgear.com/readyshare.Note: You must install this utility before you can use the ReadySHARE Printer feature.•For the ReadySHARE Printer feature to work, this utility must be run in the background.•When the status is Available, you can use the USB printer.•Some firewall software, such as Comodo, blocks the ReadySHARE Print utility from accessing the USB printer. If you do not see the printer in the utility, you can disable the firewall temporarily to allow the utility to work.If your printer supports scanning, make sure that the printer is in the Available state, and click the Network Scanner button. Clicking this button activates the Scanner window so you can use the printer for scanning.
Extender Network Settings32Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition FastLane TechnologyFastLane Technology offers maximum WiFi performance. It provides high-speed WiFi with a dedicated band connecting the extender and the wireless device, and a second band connecting the extender and the router. It is ideal for HD gaming and HD video streaming. To enable FastLane Technology:1. Select Advanced > Operating Mode.2. Select the FastLane Technology radio button.3. Review the two FastLane Technology options, and select the radio button for the WiFi band that most of your devices support.4. Click Apply.
3333. TroubleshootingThis chapter includes the following sections:•Frequently Asked Questions •Connecting to http://www.mywifiext.net •Joining WiFi Networks
Troubleshooting34Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition Frequently Asked Questions1. NETGEAR genie keeps asking me for my wireless password, and I am sure I have entered the correct wireless password. What can I do?It is likely that the extender is placed at the borderline of the range covered by the router. To resolve this, follow the instructions in Position the Extender on page 14. If you are using WEP security, make sure that you are typing the wireless key in the correct field.2. I connected to NETGEAR_EXT and launched a browser. Why am I unable to see NETGEAR genie?First, make sure that your computer is set up to use DHCP (most are). Second, make sure that the Wireless Device to Extender LED is solid green and you have a valid IP address. Finally, relaunch the browser, and enter www.mywifiext.net.3. Will the extender work if I connect it to the router with an Ethernet cable?No. The extender is designed to connect wirelessly to the router.4. I have enabled a wireless MAC filter (wireless access control – ACL) on my router. What should I do when installing the extender?The wireless device MAC address is translated to another MAC address when the wireless device connects to the extender. If your router MAC filter is enabled, the wireless device will not be able to get the IP address from the extender. To allow this wireless device to access the Internet, you must add the translated MAC address into the router.To get the translated MAC address:a. Disable the MAC filter on your router.b. Power on the extender and connect all of your wireless devices to the extender.c. Make sure that the Link Rate LED remains lit.d. Log in to your router and check the attached devices on the Attached Devices screen. Add any MAC addresses that begin with 02:0F:B5 into your router’s MAC filter table. 5. My router security is WEP, and I entered the wrong passphrase or security key on the extender. I cannot access the extender any more. What can I do?The extender cannot check to see if the WEP passphrase is correct. If you entered the wrong passphrase, your wireless device is not able to get the IP address from the extender. You must reset the extender to the factory defaults to get the IP address back.
Troubleshooting35 Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition6. I have completed the Installation Wizard, but my wireless devices cannot get the IP address from the extender. What should I do?Make sure that the passphrase you entered on your wireless device is correct, and power cycle the extender and your router. If your device is still not able to get the IP address:a. Move the extender closer to your router, and move your wireless device closer to the extender.b. Disable the wireless interface and enable it again to see if your wireless device can get the IP address.c. If your router has a MAC filter (wireless access control), disable it and follow the FAQ to add the device’s MAC address to your router.Connecting to http://www.mywifiext.netIf you have trouble connecting, try to locate the source of the problem:•For help with passwords, see Log In to the Extender on page 17.•If your browser displays an error page, make sure that you include http:// when you type this URL in the address field of your Internet browser. If you leave it out, you might not be able to connect.•The extender LEDs can help you tell if the extender is correctly set up and working as it should.-The best performance is delivered when Link Rate LED or and the Wireless Device to Extender LED are green.-A workable performance is delivered when the Link Rate LED LED or is amber and the Wireless Device to Extender LED is green.If you cannot get a wireless connection working, you can use an Ethernet cable to connect your computer to the extender. See Cable Equipment to the Ports on page 11.
Troubleshooting36Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition Joining WiFi NetworksTo join a WiFi network you have to know its network name (also called the SSID) so that you can select it. If the network is secure, you have to know the passphrase or wireless key. If the extender does not connect to the network that you selected, the following message displays:Connection was not established to the selected network.If this happens, it could be for one of these reasons:•The network name, passphrase, or key might have been typed incorrectly. Click Cancel, use the Smart Wizard to select the network from the list, and retype the passphrase or key. This is case-sensitive. PASSWORD25 is not the same as Password25 or password25.•If the Smart Wizard does not find your wireless network (it is not displayed in the Select Existing Network screen), check to see if your wireless network is still up and running. Make sure that the router is turned on. If possible, move the extender closer to the router and click Try Again. •If the extender Link Rate LED is red, this indicates a poor wireless connection. The best connection is established when there is a clear line of sight between the extender and the router you are connecting to. Make sure that there are no physical obstacles between the extender and the router, and try to move the extender closer to the router.If you use the Smart Wizard, and the extender cannot connect to the router or cannot get an IP address from the router, it displays the following message:You are not able to connect to the Internet. Click Continue to run through set up again to connect to your network.If you click Continue, the Smart Wizard starts again. If you click Exit, the Status screen displays with menu selections on the left. For more information, see Log In to the Extender on page 17.
37AA. Supplementary InformationFactory SettingsYou can press and hold the Restore Factory Settings button on the rear panel for 7 seconds. The extender resets, and returns to its factory settings.Table 2. Factory SettingsSmart Wizard EnabledWireless Wireless communication EnabledWireless network name (SSID) NETGEAR_EXTSecurity DisabledTransmission speed Auto11. Maximum wireless signal rate (IEEE Standard 802.11). Actual throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate.Country/Region United States (varies by region)Operating mode 802.11n, 802.11g, 802.11bData rate Up to 300 Mbps
Supplementary Information38Universal Dual Band WiFi Extender WN3500RP – Wallplug EditionTechnical SpecificationsTable 3. Technical specifications Network protocol and standards compatibilityData and routing protocols: TCP/IP, DHCP server and client, DNS relay, TFTP clientPower adapter • North America (input): 120V, 60 Hz, input• All regions (output): 12 V DC @ 1A output 12W maximumPhysical specifications • Dimensions: 120 x 79 x 42 mm (4.72 x 3.11 x 1.65 inches)• Weight: 238 gmEnvironmental • Operating temperature: 32° to 140° F (0° to 40° C)• Operating humidity: 90% maximum relative humidity, noncondensing• Electromagnetic emissions: Meets requirements of: FCC Part 15 Class B.Interface • Local: 10/100BASE Tx, RJ-45• 802.11n/g/b• USB 2.0 x 1, 3.5mm • Audio jack x1
39BB. Notification of ComplianceNETGEAR Dual Band - WirelessRegulatory Compliance InformationThis section includes user requirements for operating this product in accordance with National laws for usage of radio spectrum and operation of radio devices. Failure of the end-user to comply with the applicable requirements may result in unlawful operation and adverse action against the end-user by the applicable National regulatory authority.This product's firmware limits operation to only the channels allowed in a particular Region or Country. Therefore, all options described in this user's guide may not be available in your version of the product.Europe – EU Declaration of Conformity Products bearing the marking comply with the following EU directives:• EMC Directive 2004/108/EC• Low Voltage Directive 2006/95/ECIf this product has telecommunications functionality, it also complies with the requirements of the following EU Directive:• R&TTE Directive 1999/5/ECCompliance with these directives implies conformity to harmonized European standards that are noted in the EU Declaration of Conformity. For indoor use only. Valid in all EU member states, EFTA states, and Switzerland.This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 - 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France.FCC Requirements for Operation in the United States FCC Information to UserThis product does not contain any user serviceable components and is to be used with approved antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and approvals.FCC Guidelines for Human ExposureThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.This device and it's antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.FCC Declaration of ConformityWe, NETGEAR, Inc., 350 East Plumeria Drive, San Jose, CA 95134, declare under our sole responsibility that the Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition complies with Part 15 Subpart B of FCC CFR47 Rules. Operation is subject to the following two conditions:• This device may not cause harmful interference.• This device must accept any interference received, including interference that may cause undesired operation.
Notification of Compliance40Universal Dual Band WiFi Extender WN3500RP – Wallplug EditionFCC Radio Frequency Interference Warnings & InstructionsThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following methods:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and the receiver.• Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.FCC Caution• Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. • This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • For product available in the USA and Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.• Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection d'autres canaux n'est pas possible.• This device and it's antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.• Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une autre antenne ou transmetteur.• Devices will not permit operations on channels 120-132 for 11a and 11n/a which overlap the 5600 - 5650 MHz band.• This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.Canadian Department of Communications Radio Interference RegulationsThis digital apparatus (Universal Dual Band WiFi Extender WN3500RP – Wallplug Edition) does not exceed the Class B limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications.CAN ICES-3 (B)/NMB-3(B) Industry CanadaThis device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.For product available in the USA and Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection d'autres canaux n'est pas possible.This device and it's antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with IC multi-transmitter product procedures.
Notification of Compliance41Universal Dual Band WiFi Extender WN3500RP – Wallplug EditionL’émetteur ne doit pas être placé près d’une autre antenne ou d’un autre émetteur, ou fonctionner avec une autre antenne ou un autre émetteur.The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology.Le dispositif pourrait automatiquement cesser d'émettre en cas d'absence d'informations à transmettre, ou une défaillance opérationnelle. Notez que ce n'est pas l'intention d'interdire la transmission des informations de contrôle ou de signalisation ou l'utilisation de codes répétitifs lorsque requis par la technologie.Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 MHz, 5470-5600 MHz and 5650-5725 MHzSélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350 MHz, 5470-5600 MHz et 5650-5725 MHzThe maximum antenna gain permitted (for devices in the bands 5250-5350 MHz and 5470-5725 MHz) to comply with the e.i.r.p. limit.le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer à la limite de p.i.r.e.;Caution:The device for the band 5150-5250 MHz is only for indoor usage to reduce po-tential for harmful interference to co-channel mobile satellite systems. High power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN devices. Avertissement:Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utili-sation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.Les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.IMPORTANT NOTE: Radiation Exposure Statement:This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.NOTE IMPORTANTE: Déclaration d'exposition aux radiations:Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.Interference Reduction TableThe following table shows the recommended minimum distance between NETGEAR equipment and household appliances to reduce interference (in feet and meters).Household Appliance Recommended Minimum Distance(in feet and meters) Microwave ovens 30 feet / 9 metersBaby Monitor - Analog 20 feet / 6 metersBaby Monitor - Digital 40 feet / 12 metersCordless phone - Analog 20 feet / 6 meters
Notification of Compliance42Universal Dual Band WiFi Extender WN3500RP – Wallplug EditionCordless phone - Digital 30 feet / 9 metersBluetooth devices 20 feet / 6 metersZigBee 20 feet / 6 metersHousehold Appliance Recommended Minimum Distance(in feet and meters)

Navigation menu