Neets A S 313-0001 Touch Panel User Manual

Neets A/S Touch Panel

User Manual

Installation guide Neets Touch Panel™
Thank you! Thank you for including the Neets Touch Panel as part of the user interface strategy for your customer.
SpecificationsPhysical Dimensions:H: 120 mmW: 180 mmD: 41,4 mmIn wall: 25,4 mmOn wall: 17,7 mmShipping dimensions:65 mm x 280 mm x 240 mm (HxWxD)Weight:Product: 0,33 KgWall Bracket: 0,175 KgShipping: 0,85 Kg Connections:RJ45 with POE – For both Power and Ethernet communicationSwitches:Pen hole switch: 1: Access to Admin settings 2: Factory Reset switch 3: For FW upgrade onlyTouch Screen:5-point capacitive touch screenScratch resistant glass-on-glass touch screenDisplay:7” IPS Display, Resolution: 1024x595 pixelsBrightness: 350 nits (cd/m2)Sensors:Proximity sensor – For automatic display activationAmbient Light sensor – For automatic backlight dimmingPower: Power Over Ethernet (POE), IEEE802.3af, 48V (PoE injector not included)Environment:Operating Temp: 0 to 40 C / 32 to 104 FStorage Temp: 0 to 60 C / 32 to 140 FOperation moisture: Humidity: 10% to 90% RH Compliancy:CE, FCCDoc. 313-001-001 Rev. 22
What’s in the box7” Touch PanelClothWall mount bracket3
4 x Wall plugs4 x ScrewsUSB OTG adapter (for application and firmware upgrade)Ejector pin formenu settings4
FrontAmbient light sensorProximity sensor51 180 mm1 120 mm
BackFactory Reset Firmware upgradeUSBMagnets Settings buttonLAN/POEMagnetMagnet6
Steps1 Touch Panel position2 Bracket details3 Mounting the bracket4 Connect LAN/PoE5 Mount Touch Panel on bracket6 Connect PoE injector7 First start up7
1 Touch Panel position165 cm / 65 in.145 cm / 57 in.The Touch Panel is designed to wall mount in landscape orientation, and depending on how tall the users are we recommend locating the center of the touch panel between 145 cm. – 165 cm. (57” – 65”) above the finish floor. 8
2Bracket details9The Touch Panel is designed to mount into a 1- or 2-gang back box in EU, US or DK standards or can be mounted without a back box. When using EU and US standards use the threads that are already in the back box and secure the bracket with fitting screws. When using a DK standard back box use the holes marked with “W” for mounting directly on the wall. To mount the Touch Panel without back box use holes marked with “W”.
Alignment holes – do not use these for screws Holes for mounting directly into the wallUS 2-gang back boxUS 1-gang back boxEU 2-gang back boxEU 1-gang back boxWA4321A123444423221W WW WA10The numbers on the bracket refers to the back box it is intended for.
When mounting the Touch Panel into a EU/US back box follow the steps below. In case you are not mounting on a EU/US back box skip step 1.Before you start make sure the wall is even to prevent distorting the bracket.3Mounting the bracket65432111Mount the bracket onto the back box using the screws and screw holes for the specific type of back box (see page 10)Mark the center of the W-holes in the bracketDrill and insert wall plugsLevel the bracket on the wall (When mounting onto a back box do this before tightening the screws)Remove the bracket againMount the bracket and tighten the screws into the wall
12
Connect the PoE cable from the wall to the Touch Panel. Note: PoE is not included, but you can use the PoE Injector (Part number 302-000508).Connect LAN / PoE4 13
Place the Touch Panel onto the bracket. Make sure it is placed correctly and the alignment holes are free to fix the Touch Panel to all four magnets.Mount Touch Panel on bracket5 14
Power outletLAN switchPOELAN6 Connect PoE injector15
The Touch Panel will automatically power on when power is applied. Wait for the unit to start up and follow the instructions. For a complete configuration guide please go to:www.neets.dk/products/touch-panels/155You will find the instructions for firmware updates the same place.7 First start up16
Removing the Touch PanelUsing two hands grasp on each side of the Touch Panel and pull straight out from the wall. 17
Neets A/S | Langballe 4, 8700 Horsens, Denmark | +45 75 666 099 | sales@neets.dk | www.neets.dkLearn more at neets.dk Visit our website neets.dk for additional information about the product and the latest firmware.
FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Navigation menu