Nedap N V LW2450 Data Transmission System for Lamps User Manual Installation Manual

N. V. Nederlandsche Apparatenfabriek NEDAP Data Transmission System for Lamps Installation Manual

manual

Page 1 of 7 Installation Manual for the application example: Luxon Wireless 2450 June 2011
Page 2 of 7 1. Brief product description The Luxon Wireless 2450 can be added to the Luxon e-HID ballast or fixture. It regulates the communication between the ballast/fixture and the Luxon Light Controller (LLC). After installation the Luxon Wireless 2450 becomes a RF node in the network, and data can be send wirelessly to the light controller. Luxon wireless 2450 Figure 1. Installation example for the Luxon Wireless 2450 with HID lamps with a Mesh Network in a building with skylights
Page 3 of 7 2. Assembly overview for the Luxon Wireless 2450 Figure 2a: Frontplate of the end use enclosure Figure 2b: Luxon Wireless 2450 enclosure positioned on the spot mounted to the front plate Figure 2c: Luxon Wireless 2450 enclosure positioned in the hole mounted to the front plate
Page 4 of 7 Figure 2d: Luxon Wireless 2450 mechanically secured to the front plate by screws Figure 2e: Luxon Wireless 2450 wired to Figure 2f: Detailled photograph of the connectors the Luxon e-HID ballast Figure 2g: Frontview of the Luxon e-HID ballast
Page 5 of 7 3. Positioning The Luxon Wireless 2450 will be mounted to a cover of a Luxon e-HID ballast or fixture Note: 1) This transmitter should only be used or installed at locations where there is at least 20cm separation distance between the antenna and all persons. This is to comply with FCC RF exposure requirements for mobile transmitting devices. 2) The Luxon Wireless 2450 shall never be installed inside a metal power cabinet. This would impede wireless communication. Fig 3 No installation of the Luxon Sensor Bridge inside a metal enclosure 5. Powering the Luxon Wireless 2450 The Luxon Wireless 2450 is powered by a 12V DC-source from the Luxon e-HID PCB. 6. Specifications for application Luxon Wireless 2450 Operating temperature Safety EMC/Telecom -40 to +85°C EN60950 EN301489-1, EN300328 V1.7.1 FCC47 part 15 and IC RSS210 Dimensions 40X53 mm Input Supply 12 Vdc, max 0.1 mA
Page 6 of 7 7. FCC and IC Declarations for Luxon Wireless 2450 This device contains Luxon Wireless 2450 with FCC ID: CGDLW2450 and IC: 1444A-LW2450 Compliance statement This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Déclaration Conformité Cet appareil se conforme aux normes RSS exemptés de license du Industry Canada. L'opération est soumis aux deux conditions suivantes (1) cet appareil ne doit causer aucune interférence, et (2) cet appareil doit accepter n'importe quelle interférence, y inclus interférence qui peut causer une opération non pas voulu de cet appareil. Warning Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. RF Exposure To comply with FCC RF exposure requirements for mobile transmitting devices, this transmitter should only be used or installed at locations where there is at least 20cm separation distance between the antenna and all persons. 8. Label artwork for application Luxon Wireless 2450 end product example Fig 4: Label artwork for Luxon Wireless 2450 end product example.
Page 7 of 7 9. Label location Luxon e-HID ballast. Attach the label to the Luxon e-HID ballast as shown in the following figure 5. Fig. 5. Label location

Navigation menu