National Electronics and Watch M08-255-256 Bike Computer(RX) User Manual Wintech USB GB

National Electronics & Watch Co., Ltd Bike Computer(RX) Wintech USB GB

UserManual.wiki >

National Electronics and Watch >

M08 255 256 User Manual

UH5M08 255 256 User manual

1WINTECH USB Ultimate 2010- User GuideThe Mavic team has put all its passion, experience and skill into the design and manufacture of your computer. It will be an important tool for you in the improvement of your performance.Thank you for putting your trust in Mavic products.INSIDE1. PRODUCT DESCRIPTIONINSTALLATION2. INSTALLING THE COMPUTER MOUNT3. FITTING / REMOVING THE COMPUTER4. INSTALLING THE SPEED SENSORS 4.1. E-Skewer 4.2. E-Bolt 4.3. Fork Sensor5. INSTALLING THE WHEEL MAGNET6. INSTALLING THE BATTERIESBASIC NAVIGATION7. DESCRIPTION OF THE DISPLAY8. FUNCTION DISPLAY DEFAULT SEQUENCE9. DEFAULT BUTTON FUNCTION MATRIXSETTINGS10. ENTERING THE SET UP MENU 10.1. Heart rate alarm and workzone (Wintech USB HR and Wintech USB Ultimate only) 10.2. DIGITAL PAIRING 10.3. Elevation set up (Wintech USB Alti and Wintech USB Ultimate only) 10.4. Wheel circumferences and distance unit set up 10.5. Clock set up 10.6. Odometers set upUSE11. SLEEP MODE12. TRIP RESET13. USE OF LAP TIME (CR)14. ELEVATION SET UP AND DATA REVIEW MENU 14.1. Entering the Elevation set up and data review menu 14.2. Recall of Home Altitude (Wintech USB Alti and Wintech USB Ultimate only) 14.3. Setting up the current elevation (Wintech USB Alti and Wintech USB Ultimate only) 14.4. Trip Altitude and Heart Rate data review (Wintech USB Alti, Wintech USB HR and Wintech USB Ultimate only) 14.5. Lap time data review 14.6. Odometers review15. VERTICAL SPEED EXPLAINED (Wintech USB Alti and Wintech USB Ultimate only)16. PC PLUG17. MAINTENANCE AND RECOMMENDATION OF USE18. WINTECH DEVICES TECHNICAL SPECIFICATIONS19. WARRANTYWINTECH MANAGER SOFTWARE20. ENTERING WINTECH MANAGER21. DATA TRANSFER22. TRIPS23. REPORTS24. COMPUTER SETTINGS AND USER ACCOUNT MANAGEMENT 24.1. Create a new user or edit an already existing user 24.2. Screen customization25. BIKE SETTINGS26. LINKS27. WINTECH MANAGER TECHNICAL SPECIFICATION

21. PRODUCT DESCRIPTIONMain Unit Boxa. Computerb. Cardio Beltc. Wintech Manager software CDd. Memo stickSensor BoxE-Skewere. E-Skewer sensorf. Computer mountg. 25,4mm handlebar reducerh. Wheel magnetE-Bolti. E-Bolt sensorf. Computer mountg. 25,4mm handlebar reducerh. Wheel magnetj. Adjustment magnetsFork Sensork. Fork sensorf. Computer mountg. 25,4mm handlbar reducerh. Wheel magnetl. Zip ties (x3)After installation and before you use your computer for the ﬁrst time, you MUST perform the digital pairing operation described in section 10.2. of this guide. If you don’t, there will be no communication between the computer and the diﬀerent sensors and your system will not work.INSTALLATION2. INSTALLING THE COMPUTER MOUNT2.1 Install the mount on the handlebar, to the right of the stem. To ﬁx it to an oversize, 25.4 diameter handlebar, use the 25.4 adapter.2.2 The mount can be installed in a variety of positions: with the computer forward of, or above the handlebar stem. 2.3. When setting it, the computer support needs to turn freely on the mount arm. Loosen the screw using a cross-slot screwdriver2.4. Once you have chosen the right position, tighten the mount screw with a cross-slot screwdriver and secure the computer support screw again.3. FITTING/REMOVING THE COMPUTER3.1. Slide the computer onto the mount from the front until it locks into place with an audible click.3.2. To remove the computer from its mount, press and hold the tab located under the computer mount and slide the computer toward the front of the bicycle. wintech managerbahjkilc degf(x3)122.12.3 2.42.23.1 3.2

34. INSTALLING THE SPEED SENSORS4.1 E-SkewerFit the quick-release lever to the hub, with the lever to the left (to the right when using disc brakes). Position of the locking lever Adjust the tension on the adjusting nut so that suﬃcient force is applied when the locking lever is moved to the “CLOSE” position (consult your retailer). If the quick release lever can be moved too easily to the CLOSE position, there will be insuﬃcient force holding the wheel. If this is the case, place the quick release lever in the OPEN position again and tighten the adjusting nut to increase the force. Then, push again the quick release lever to the CLOSE position.If too much force is needed to move the quick release lever to the CLOSE position, place the lever in the OPEN position again, and unscrew the adjustment nut to reduce the force. Then, push again the quick release lever to the CLOSE position.Once the adjustment nut has been set, the end of the quick release shaft must not be sunk more than 2 mm in from the outside edge of the adjustment nut.Make sure the wheel is securely tightened: raise the front wheel oﬀ the ground and strike the top of the wheel sharply in a downward direction. The wheel must remain ﬁrmly in place.IMPORTANT: At this point, your computer is not yet ready to work. You still need to set the necessary programs, and then perform the pairing operation of your device.4.2. E-BoltThe speed sensor is integrated into a ﬁxing nut compatible with all quick-releases on the market. To install it, unscrew the ﬁxing nut on your quick-release. Insert the quick release from the left-hand side of your bike and tighten the electronic ﬁxing nut from the right-hand side. Adjust the tightness of the nut according to the recommendation described in section 4.1 of this user guide.4.2.1 Road bikeOnce suﬃciently tightened, position the sensor towards the rear before closing the quick-release.4.2.2. Mountain bike. Once suﬃciently tightened, position the sensor towards the top before closing the quick-release.IMPORTANT: At this point, your computer is not yet ready to work. You still need to set the necessary programs, and then perform the pairing operation of your device.4.3 Fork SensorTo install the Fork sensor, the wheel magnet must be installed ﬁrst. Read section 5 of this user guide ﬁrst.Adjust the position of the speed sensor so the center of the magnet is aligned with one of the arrows on the sensor. The distance between the magnet and the sensor must be between 5 - 10 mm. 5.4 Tighten the wire tires and cut them ﬂush.IMPORTANT: At this point, your computer is not yet ready to work. You still need to set the necessary programs, and then perform the pairing operation of your device.OKOPEN OPENCLOSE4.2.14.24.34.2.24.1

45. INSTALLING THE WHEEL MAGNET5.1 Position the magnet on a spoke so that it passes opposite either of the lever marks and at a maximum distance of 5 mm. The magnet must be facing outward from the wheel.5.2 If you use the E-Bolt sensor, on a mountain bike, it might be necessary to use the adjustment magnets to reduce the distance between the sensor and the magnet.The magnet must be facing outward from the wheel.5.3 Must be cut for use on bladed Zicral spokes.6. INSTALLING THE BATTERIESPower supply for the computer: 1 CR2430 battery.Power supply for the speed sensor: 1 CR2032 battery.Power supply for the cardio belt (Wintech USB HR and Wintech USB Ultimate only): 1 CR2032 battery.Only use this type of battery.Installing the batteries in the computer, speed and cadence sensors:6.1. Remove the battery cover by turning it a quarter turn counterclockwise, using a coin or a battery.6.2. Insert the battery into its recess, keeping the + side uppermost.6.3. Reﬁt the battery cover and close it by turning it a quarter turn clockwise.Do not to use excessive force, or you will damage the unit.Check the condition of the seal on the battery cover each time you change the battery. Replace the battery cover if the seal is damaged. Always perform the above operations in a dry place. Changing the computer’s batteries has the eﬀect of zeroing the following parameters:– total distance;– measurement unit (M or KM);– wheel circumference;– time.After installation, or after changing batteries (in sensors or computers), it is imperative to repeat the digital pairing operation described in section 10.2 of this notice.Battery life: 12 to 24 months depending on use.BASIC NAVIGATION7. DESCRIPTION OF THE DISPLAYBK 1, 2 or H Number of bike usedAV Average speed (up to 99,9 km/h or 62 Mi/h) MAX Maximum speed (up to 99,9 km/h or 62 Mi/h) KM / Mi Distances in kilometres or miles Trend indicator: if the current speed exceeds the average speed, the up arrow is displayed. If the current speed is below the average speed, the down arrow is displayed. If the current speed equals the average speed, no arrow is displayed. Altimeter indication line (Wintech USB Alti and Wintech USB Ultimate only)VS Vertical speed (up to 2500m/h or 8202,5 ft/h). In meters per hour (m/h) or feet per hour (ft/h)ASC Altitude gain Temperature indicator (from -15°C / 5°F to 50°C/122°F) Slope indicator (from -25 to +25 %)m/h ft/h Vertical speed in meter or feet Heart rate indication line - up to 240 bpm (Wintech USB HR and Wintech USB Ultimate only)AV Average heart rateMax Maximum heart rate Heart rate displayed as a percentage of maximum heart rate Sound alarm. Displayed only when alarm is turned onCAD Pedaling cadence (optional – up to 180)DST Trip distance (up to 1999.99)CR 1 to 9 Lap timeATM Stopwatch (up to 19 h 59 min 59 s)ODO Distance totalizer (up to 99.999)5.15.25.36.16.36.2

58. FUNCTION DISPLAY DEFAULT SEQUENCE8.1 Brieﬂy press right button (BPR) to scroll down the “while riding” displays (live information)Screen 1 – Current speed – Number of bike used – Distance unit (KM or Mi) – Current elevation (Wintech USB Alti and Wintech USB Ultimate only) – Current heart rate (Wintech USB HR and Wintech USB Ultimate only) – Current pedalling cadence (optional)Screen 2 – Current speed – Number of bike used – Distance unit (KM or Mi) – Vertical speed (Wintech USB Alti and Wintech USB Ultimate only) – Heart rate as a percentage of maximum heart rate (Wintech USB HR and Wintech USB Ultimate only) – Trip distanceScreen 3 – Current speed – Number of bike used – Distance unit (KM or Mi) – Slope % (Wintech USB Alti and Wintech USB Ultimate only) – Current heart rate (Wintech USB HR and Wintech USB Ultimate only) – Stopwatch (ATM)8.2 Brieﬂy press left button (BPL) to scroll down the “after riding” displays (statistic information)Screen 4 – Average speed – Number of bike used – Distance unit (KM or Mi) – Cumulated altitude gain (Wintech USB Alti and Wintech USB Ultimate only) – Average heart rate (Wintech USB HR and Wintech USB Ultimate only) – ClockScreen 5 – Max speed – Number of bike used – Distance unit (KM or Mi) – Temperature (Wintech USB Alti and Wintech USB Ultimate only) – Max heart rate (Wintech USB HR and Wintech USB Ultimate only) – Total cumulated distance (odometer) of the active bike (BK1, BK2 or BKH).8.3 Active display when the computer is connected with USB to a laptop or desktop. None of the buttons (BPR and BPL) are active.You can customize the 5 default screens above by using the Wintech Manager software included on the CD delivered with your computer.9. DEFAULT BUTTON FUNCTION MATRIXLeft Button Right ButtonFrom Short press Long press > 2s From Short press Long press > 2s Long press > 6sScreen 1 To screen 4Elevation set up + data reviewScreen 1 To screen 2Start/stop CR (intermediate chrono)Parameters set up zoneScreen 2 To screen 5 Screen 2 To screen 3Screen 3 To screen 4 Screen 3 To screen 1Screen 4 To screen 5 Screen 4 To screen 2Screen 5 To screen 4 Screen 5 To screen 3 SETTINGS10. ENTERING THE SET UP MENUFrom any screen, press and hold the right button (BPR) for 6 seconds to enter the set up menu.The set up menu is sequentially organized in sub-menus, in the following order:1. HR alarm and working zone (Wintech USB Alti and Wintech USB Ultimate only)2. Digital pairing of bike sensor3. Home elevation, altitude and temperature unit (Wintech USB HR and Wintech USB Ultimate only)4. Wheel circumference and distance unit5. Clock6. OdometersTo move from one sub-menu to the next one, brieﬂy press the left button (BPL).After the odo sub-menu, pressing again brieﬂy the left button, exit the set up menu and return to the previous active screen.When on one of the sub-menu, brieﬂy press the right button to enter this sub-menu.In set up mode, when there is no operation for 2min, the computer automatically exits the set up menu and return to the previous active screen.Those set up operations have to be performed each time the battery is removed or changed.Those set up operation can be performed more easily and more rapidly using the Wintech Manager software delivered with your computer.Screen 1Screen 4Screen 6Screen 5Screen 2 Screen 38.18.28.36 sec.any screen1 click1 clickenter1 clickenter1 clickenter1 clickenter1 clickenter1 clickenter1 click 1 click 1 click 1 click 1 clickEXIT10

8See part 14.2 of this user guide to learn how to use the Home Elevation.The Home altitude is useful to easily and rapidly recalibrate your computer before you start a new ride. The Home altitude shall be set up at your most frequent point of departure. We recommend that you precisely know the elevation of this point.10.3.4. Choose your temperature unit (Celsius or Fahrenheit).As a result from the last brief press on the right button (BPR) to validate the home altitude, you enter the temperature unit set up: ° ﬂashes.Brieﬂy press the left button (BPL) to change from Celsius (C) to Fahrenheit (F). Validate your choice by brieﬂy pressing the right button (BPR) and exit the elevation menu. You will automatically return to the last active display.Choosing the temperature unit (°C or °F) automatically updates the elevation (m or ft) and distance unit (km or mi) according to the metric or imperial measurement standard. 10.4. Wheel circumferences and distance unit set up Consult the table of approximate correspondences to check your wheel circumference (see table 10.4.). For a more precise measurement, proceed as follows: – Make a mark on the tire and on the ground at the point of contact between the tire and the ground.– Do one full turn of the wheel and mark on the ground the place where the mark on the tire touches the ground.– Measure the distance (D) between these two points in millimeters. 10.4.1. Enter the Wheel circumferences set up menu:From any active display, press and hold the right button (BPR) for 6 seconds.– On Wintech USB Ultimate, brieﬂy press the left button (BPL) 3 times to move to the wheel circumferences and distance unit set up section. “Cir” appears on the screen.– On Wintech USB Alti and Wintech USB HR, brieﬂy press the left button (BPL) twice to move to the wheel circumferences and distance unit set up section. “Cir” appears on the screen.– On Wintech USB, brieﬂy press the left button (BPL) once to move to the wheel circumferences and distance unit set up section. “Cir” appears on the screen.Brieﬂy press the right button (BPR) to start the wheel circumferences and distance unit settings operations. Cir and BK appear on the screen and the bike number ﬂashes beside BK.Tyre Circumf. Tyre Circumf.26’’x1,5 2020 700Cx19 210026’’x1,75 2070 700Cx20 211026’’x1,9 2090 700Cx23 213026’’x2,0 2110 700Cx25 214026’’x2,1 2130 700Cx28 215026’’x2,2 2150 700Cx32 217026’’x2,3 2170 700Cx35 2200650Cx19 1930650Cx23 199010.410.4.110.4.2 10.4.310.4.46 sec.3 click (Ultimate)2 click (Alti, HR)1 click (USB)1 click1 click1 click1 click1 click1 click1 clickany screenselectselectselectselectselectselectEXIT

910.4.2. Choose the bike number you wish to set up the wheel circumference and distance unit for.Brieﬂy press the left button (BPL) to change from BK 1, to BK 2 to BK H (for home trainer).Brieﬂy press the right button (BPR) to validate your selection and switch to the wheel circumference set up screen. The ﬁrst wheel circumference of the selected bike ﬂashes.10.4.3. Set up the wheel circumference of the selected bike.Brieﬂy press the left button (BPL) to set up the ﬁrst digit of the chosen bike wheel circumference. Brieﬂy press the right button (BPR) to validate your choice and move to the next digit.Repeat those steps to the 4th digit. Validating the 4th digit by a brief press on the right button (BPR) will move you to the distance unit setting screen. The distance unit display ﬂashes.10.4.4. Select the distance unit of the selected bike.Brieﬂy press the left button to select kilometres (KM) or Miles (Mi).Brieﬂy press the right button (BPR) to validate your selection and exit the wheel circumference and distance unit set up menu. You will automatically return to the last active display.Choosing the distance unit (Km or Mi) automatically updates the elevation (m or ft) and temperature unit (°C or °F) according to the metric or imperial measurement standard.To set up the wheel circumference and distance unit for a 2nd bike sensor or the home trainer sensor, proceed again to the operations described above, selecting the correct bike number.10.5. Clock set upEnter the Clock set up menu:From any active display, press and hold the right button (BPR) for 6 seconds.– On Wintech USB Ultimate, brieﬂy press the left button (BPL) 4 times to move to the clock set up section. The current clock is displayed on the screen.– On Wintech USB Alti and Wintech USB HR, brieﬂy press the left button (BPL) 3 times to move to the clock set up section. The current clock is displayed on the screen.– On Wintech USB, brieﬂy press the left button (BPL) twice to move to the clock set up section. The current clock is displayed on the screen.Brieﬂy press the right button (BPR) to start the clock settings operations. The ﬁrst hour digit ﬂashes.Brieﬂy press the left button (BPL) to adjust the ﬁrst hour digit. Brieﬂy press the right button (BPR) to validate your choice and move to the next digit.Repeat those steps to the 2nd minute digit. Validating the 2nd minute digit by a brief press on the right button (BPR) will exit the set up menu and switch back to the last active screen.10.56 sec.4 click (Ultimate)3 click (Alti, HR)2 click (USB)1 click1 click1 click1 click1 clickany screenselectselectselectselectEXIT

1010.6. Odometers set up10.6.1. Enter the Odometers set up menu:From any active display, press and hold the right button (BPR) for 6 seconds.– On Wintech USB Ultimate, brieﬂy press the left button (BPL) 5 times to move to the odometer section. “odo” appears on the screen.– On Wintech USB Alti and Wintech USB HR, brieﬂy press the left button (BPL) 4 times to move to the odometer section. “odo” appears on the screen.– On Wintech USB, brieﬂy press the left button (BPL) 3 times to move to the odometer section. “odo” appears on the screen.Brieﬂy press the right button (BPR) to start the odometers settings operations. The bike number ﬂashes.10.6.2. Select the bike number you wish to adjust the odometer for.Brieﬂy press the left button (BPL) to select the bike number you wish to adjust the odometer for.Brieﬂy press the right button (BPR) to validate the bike number selection and switch to the odometer set up screen.10.6.3. Adjust the odometer for the selected bike.Brieﬂy press the left button (BPL) to adjust the ﬁrst digit. Brieﬂy press the right button (BPR) to validate your choice and move to the next digit.Repeat those steps to the 5th odometer digit. Validating the 5th odometer digit by a brief press on the right button (BPR) will exit the set up menu and switch back to the last active screen.To set up the odometer for a 2nd bike sensor or the home trainer sensor, proceed again to the operations described above, selecting the correct bike number. USE11. SLEEP MODEWhen no speed, cadence and heart rate signals is detected and none of the buttons are pressed for 15 minutes, then the computer automatically switches to sleep mode, to save the battery.Your Wintech computer does not wake up automatically when riding.Press any of the 2 buttons to wake the computer up. The last active display will be displayed.When the computer wakes up, the BK displays starts to ﬂash. It means that the computer is looking for the speed sensor signals. When a signal is recognized, the BK displays stops ﬂashing and is completed by the bike number of the recognized sensor (1,2 or HT). The displayed data automatically switch to the corresponding sensor. 6 sec.5 click (Ultimate)4 click (Alti, HR)3 click (USB)1 click1 click1 click1 click 1 click1 click 1 clickany screenselectselectselect selectselect selectorauto10.6.110.6.2 10.6.311EXIT

1112. TRIP RESET12.1. To reset your last trip, press and hold the 2 buttons together for 2 seconds.The reset data are:– Trip distance– Average speed– Maximum speed– Vertical speed– Cumulated vertical gain– Lap time and their associated data Clock, Odometers, Home and Current altitude are not reset.Wintech USB computers can store up to 10 trips of 5 hours each in its internal memory. Only the last one is displayed on the Wintech computer itself.When you reset the last trip, it does not erase the internal memory of the Wintech computers. Those 10 last trips are still available for download at the next PC connection.So, if you ride for several days without downloading your Wintech data to your PC, you will not lose any of the 10 last trips, while still being able to reset the last trip before the next one.The 11th trip will replace the oldest of the 10 previous trips.12.2. FULL 0 RESETOnce the daily trip has been reset, if you press and hold together the 2 buttons (BPR and BPL) for 8 seconds, the reset of the whole system starts and all default settings will be restored.All screen digits and logos will light up for 3 seconds. Then, the digits will count down from 9 to 0 and after 6 seconds, screen 1 will be displayed.This operation erases your settings and replaces them with the default settings. It also cancels the sensor pairing. So, before it works properly, you need to pair all the sensors again, following the instruction described in section 10.2 of this user guide. 13. USE OF LAP TIME (CR)In the course of a session you can use up to 9 lap times in order to evaluate your performance on speciﬁc hills or sections.Remember, the lap time only starts during a session i.e. when the computer already indicates a speed.From any screen in the course of a session, press and hold the right button for 2 seconds to start the lap time. The “CR” symbol ﬂashes. The lap time starts when you release the right button and indicates the number of the lap time.When a lap time has been started, the elapsed time of the current lap time replaces the “ATM” data in screen 3.To stop the current lap time, from any screen, press the right button for 2 seconds. The screen automatically switches to screen 3, displaying the “ATM” of the lap time you have just stopped. Press any button, to return to the overall display of your session.To start the next lap time, press the right button for another 2 seconds, and so on for the 9 possible lap times.When all 9 lap times are used, “FULL” appears on the display if you try to start a new lap time.The computer automatically returns to screen 3 after 2 seconds.To learn how to read the lap time data, go to section 14.4 of this user guide. 2 sec.any screen8 sec.3 sec. auto3 sec. auto3 sec. auto2 sec. 2 sec. After 2 sec. autoto CR9Start CR1 Stop CR1any screen(1, 2, 3, 4, 5)12.11312.2

1314.4. Trip Altitude and Heart Rate data review (Wintech USB Alti, Wintech USB HR and Wintech USB Ultimate only)Enter the elevation set up and data review menu: From any screen, press the left button for 2 seconds.– On Wintech USB Alti and Wintech USB Ultimate, brieﬂy press the left button (BPL) twice to switch to the altitude and heart rate review data section: “Info” appears on the computer screen.– On Wintech USB HR “Info” appears on the computer screen.Brieﬂy press the right button (BPR) to enter the altitude and heart rate review data section.The review of trip altitude and heart rate data automatically starts in the following order:– Highest trip elevation “Hi” (Wintech USB Alti and Wintech USB Ultimate only)– Lowest trip elevation “Lo” (Wintech USB Alti and Wintech USB Ultimate only)– Time spent bellow the HR target zone “Lo” (Wintech USB HR and Wintech USB Ultimate only)– Time spent into the HR target zone “In” (Wintech USB HR and Wintech USB Ultimate only)– Time spent above the HR target zone “Hi” (Wintech USB HR and Wintech USB Ultimate only)Each piece of information is displayed for 3 seconds.For Wintech USB HR, if no heart rate information has been recorded during the trip (when not wearing the HR belt for instance), it is not possible to enter the Heart rate data review section when brieﬂy pressing the right button on the “Info” screen.For Wintech USB Ultimate, if no heart rate information has been recorded during the trip (when not wearing the HR belt for instance), only elevation information will be displayed.These data will cycle through until you press and hold the left button for 2 seconds. Then, the computer switches back to the last active screen.If no button is pressed for 2 minutes, the computer automatically switches back to the last active screen.14.42 sec.AltiUltimateHR2 click1 clickafter 3 sec auto2 sec 2 sec 2 sec 2 sec 2 secafter 3 sec autoafter 3 sec autoafter 3 sec autoafter 3 sec autoany screenEXIT EXIT EXIT EXIT EXIT

1414.5. Lap time data reviewEnter the elevation set up and data review menu: From any screen, press the left button for 2 seconds.– On Wintech USB Alti and Wintech USB Ultimate, brieﬂy press the left button (BPL) 3 times to switch to the lap time data review section: “Cr” appears on the computer screen.– On Wintech USB HR, brieﬂy press the left button (BPL) once to switch to the lap time data review section: “Cr” appears on the computer screen.– On Wintech USB “Cr” appears on the computer screen.Brieﬂy press the right button (BPR) to enter the lap time data review section.The review of the ﬁrst lap time automatically starts in the following order:– Elapsed time in the ﬁrst lap time– Distance ridden during the lap time– Average speed during the lap time– Average vertical speed during the lap time (Wintech USB Alti and Wintech USB Ultimate only)– Average slope in % during the lap time (Wintech USB Alti and Wintech USB Ultimate only)Each piece of information is displayed for 3 seconds.If no lap time has been recorded during the trip, it is not possible to enter the lap time data review section when brieﬂy pressing the right button on the “Info” screen.At any time of the sequence, brieﬂy press the left button (BPL) to switch to the next lap time.These data will cycle through until you press and hold the left button for 2 seconds. Then, the computer switches back to the last active screen.If no button is pressed for 2 minutes, the computer automatically switches back to the last active screen.14.52 sec.AltiUltimateUSBHR3 click1 click1 clickafter 3 sec auto1 click 1 click 1 click 1 click 1 clicknext CR next CR next CR next CR next CRafter 3 sec autoafter 3 sec autoafter 3 sec autoafter 3 sec autoany screen2 sec 2 sec 2 sec 2 sec 2 secEXIT EXIT EXIT EXIT EXIT

1514.6. Odometers reviewProceed this way to read the diﬀerent bike / speed sensor odometers data.Enter the elevation set up and data review menu: From any screen, press the left button for 2 seconds.– On Wintech USB Alti and Wintech USB Ultimate, brieﬂy press the left button (BPL) 4 times to switch to the odometer review section: “odo” appears on the computer screen.– On Wintech USB HR, brieﬂy press the left button (BPL) twice to switch to the odometer review section: “odo” appears on the computer screen.– On Wintech USB, brieﬂy press the left button (BPL) once to switch to the odometer review section. “odo” appears on the computer screen.Brieﬂy press the right button (BPR) to enter the odometer review section.The review of odometers from the diﬀerent speed sensors automatically starts in the following order:– Bike 1– Bike 2– Bike H– TotalEach piece of information is displayed for 3 seconds.These data will run around until you press and hold the left button for 2 seconds. Then, the computer switches back to the last active screen.If no button is pressed for 2 minutes, the computer automatically switches back to the last active screen.14.62 sec.AltiUltimateUSBHR4 click1 click2 click1 clickafter 3 sec autoafter 3 sec autoafter 3 sec autoafter 3 sec autoany screen2 sec 2 sec 2 sec 2 secEXIT EXIT EXIT EXIT

1615. VERTICAL SPEED EXPLAINED (Wintech USB Alti and Wintech USB Ultimate only)The Vertical Speed (VS) function available on Screen 2 gives you the opportunity to measure your performance on any ascension of a pass, or a steep climb. It expresses the vertical elevation achieved in one hour (in feet or meter); and depends on the cyclist speed and the slope of the climb. For your information, a professional cyclist extremely well prepared will be able to reach vertical speed values around 5900 ft/h / 1800 m/h.Your Wintech computer will provide you with an always positive vertical speed value, when climbing or going downhill. The display is limited at 2500 m/h or 8202,5 ft/h. 16. PC PLUGThe data recorded in your Wintech computer can be read and changed from your PC by pluging directly the Wintech computer into the USB port of your PC.With the USB plug, connect your Wintech computer with to your PC to:– Upload your personal settings into your Wintech computer: home elevation, wheel circumferences, clock, odometers.– Download your recorded rides to analyze distance, elevation, heart rate and Lap time data on graphs and charts.To perform those operation, you need to install on your PC the Wintech Manager software included on the CD delivered with your Wintech computer (see Wintech Manager user guide for details on installation and use of the Wintech Manager software).To plug your Wintech computer to your PC:– Remove the computer from the handlebar mount– Remove the USB plug cap from the USB plug of the Wintech computer– Plug your Wintech computer directly to the USB port of your PC or using a USB extension wire.– The screen of your Wintech computer will indicate PC. If not, the Wintech computer might not be plugged correctly. Reverse it.Once the Wintech manager software is installed, when the Wintech computer is connected to the PC, the Wintech Manager software is automatically launched.The “Download data” dialog box pops up: click on “download data” to download the Wintech computer’s data. A “Success” dialog box pops up when the download is complete.If the last trip has not been reset to 0, it will not be downloaded. To remove your Wintech computer from your PC, simply unplug it. Make sure no download is in progress.The clock of the Wintech computer is automatically updated with the clock of the PC.Read section 20 to 26 of this user guide to learn more about data download and the Wintech Manager software.17. MAINTENANCE AND RECOMMENDATION OF USE– Changing the batteries: use CR 2032 batteries only for the speed sensor and cardio belt; and CR2430 batteries only for the computer. – Changing the computer battery automatically sets the following parameters at zero: odometer, measuring unit (M or KM), wheel circumference, time. Remember to repeat the pairing operation each time you change batteries. – Service life of batteries: 12 to 24 months depending on usage.– Although the electronic systems are watertight, avoid subjecting them to high-pressure water jets. – Although they resist solvents and oil-based products, avoid using this type of product in the maintenance of the diﬀerent components. – Tip: use lukewarm water, with soap if necessary, and then wipe with a dry cloth. – Do not leave the computer exposed to sunlight (e.g. behind a windscreen) when not in use.– Do not disassemble any components or the guarantee will cease to be applicable.– Cycling is a sport that can demand intense physical activity and present variable risks depending on routes and the environment. Use your road sense and keep an eye out for traﬃc. Remember to wear a helmet. – Product characteristics, shape and general presentation are subject to modiﬁcation without prior warning.Instructions for Disposal of Waste Equipment by Users in Private Household:This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop oﬀ your waste equipment for recycling, please contact your local city oﬃce, your household waste disposal service or the shop where you purchased the product.18. TECHNICAL SPECIFICATIONS– Transmission: the use of digitally coded radio wave technology (WIN®) to transmit data provides optimal reliability. However, disturbances may occur in the vicinity of electrical apparatus, overhead power lines…– Normal operating temperature: from –10 to +50°C / 14°F to 122°F.– Speed: from 4.0 km/h to 99.9 km/h / from 2.5 mi/h to 62.0 mi/h– Trip Distance: up to 1999,99 km or mi– Odometer: up to 99999 km or mi– Riding time: up to 19h59mn59sec– Clock: 24h only– Cadence: from 10 to 180 RPM– Heart rate: from 25 to 240 BPM (Wintech USB HR and Wintech USB Ultimate only)

17– Altimeter: from -500m to 5000m / -1640 ft to 16400 ft. Accuracy: +/- 5m / +/- 16 ft (Wintech USB Alti and Wintech USB Ultimate only)– Vertical speed: from 0 to 2500 m/h (8200 ft/h). Accuracy: +/- 10m/h (32,8 ft). Calculated on the elevation change within the last 30 seconds. (Wintech USB Alti and Wintech USB Ultimate only)– Average vertical speed calculation: (Elevation at stop point – elevation at start point)/ATM in minutes x 60. (Wintech USB Alti and Wintech USB Ultimate only)– Cumulated altitude gain calculation: sum of all positive elevation change of the daily trip. (Wintech USB Alti and Wintech USB Ultimate only)– Slope: from -25% to +25%. Accuracy: 1%. Calculated on the elevation change over the last 100 meters. (Wintech USB Alti and Wintech USB Ultimate only)– Average slope % calculation: (Elevation at stop point – elevation at start point)/DST in meters x 100. (Wintech USB Alti and Wintech USB Ultimate only)– Temperature: from -15°C to +50°C / From +5°F to +50°F. Accuracy: +/- 1°C (1°F). (Wintech USB Alti and Wintech USB Ultimate only)– Wheel circumference: from 1500mm to 2500mm. Step: 1 mm.– Internal memory: up to 10 trips of 5 hours each19. MAVIC® 2-YEAR WARRANTYMavic products purchased through an authorised retailer are warranted against defects in materials and workmanship for 2 years from date of purchase by the initial user, under the conditions deﬁned below.In order to make a claim under this warranty, the consumer must keep proof of purchase, including the date and the name of the authorized dealer, and comply with the prescribed procedure.OBLIGATIONSIn the event of a defect on one of its products, Mavic’s sole obligation under this warranty is to repair or replace, at its discretion, the defective part or product.Moreover, in some countries, Mavic is obliged to ensure any legal warranty deﬁned by law, for the consumer’s protection. In this respect, in France, Mavic ensures legal warranty against hidden defects under the conditions and limits of article 1641 and following of the French “Code Civil”.LIMITS OF WARRANTYThis warranty does not cover normal wear and tear or damage resulting from shipment, storage, accidents, negligence, shocks or crashes, failure to follow the user’s guide and/or recommendations for use, improper assembly or assembly with incompatible products, poor maintenance, misuse, modiﬁcation or alteration of the product.The conditions of the Mavic warranty, including those applicable to product conformity, do not apply to products purchased from outlets other than retailers authorized by Mavic.This warranty is not transferable and is only applicable to the initial purchaser.This warranty does not cover parts that are subject to wear in normal use, such as the braking surfaces of wheel rims (if a rim braking system is used), brake pads, bearings, pawls, rear derailleur jockey wheels, batteries...This warranty does not cover products repaired or serviced by anyone other than Mavic After-Sales Service personnel or Mavic’s representative in the country concerned (1).This warranty does not cover products whose serial numbers or identiﬁcation have been erased, damaged or modiﬁed.This warranty does not cover “Spécial Service Course Mavic®” (2) products.This warranty does not exclude rights speciﬁc to each country. Consumers may have other rights depending on their place of residence.Certain juridictions make no provision for the exclusion or limitation of speciﬁc, incidental or consequential damages, or limitations on the warranty period; the above exclusions and limitations do not therefore apply to all. Local taxes, customs duties or freight charges may be applied. In the United States, additional rights that diﬀer from one state to another may also be applied. Should part of this warranty be found to be inapplicable by virtue of administrative or legal proceedings, the other parts remain applicable.CLAIMS UNDER WARRANTY - PROCEDUREAuthorised retailers are at the users’ disposal to manage any warranty claims.The authorised retailer must obtain the consent of Mavic® After- Sales Service (or its representative in the country concerned (1)) prior to returning a product under warranty. The entire product, accompanied by proof of the date of purchase (warranty card dated, signed and stamped by the authorised retailer or other proof of the date of purchase) shall be sent by the authorised retailer to Mavic® After-Sales Service (or its representative in the country concerned (1)), which will undertake the operation.The new or repaired product shall be returned to the authorized retailer.WARRANTY CARDThe warranty card printed on this document must be dated, signed and stamped by the authorised retailer and kept in a safe place indeﬁnitely. It must be used for any claims.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.(1) Up-to-date list available on request from: MAVIC, 74996 ANNECY CEDEX 9.(2) Claims made by other means or without obtaining prior consent for return cannot be taken into consideration.WIN-Tech is protected by one or more of the following patents: US 6204775 and other patent pending.SALOMON S.A.S. — MAVIC®Capital : 23 509 981, 50 eurosSiège social : Lieu-dit «La Ravoire» Metz-Tessy (74)R.C.S. Annecy 325 820 751 - 00106 - A.P.E. 364 ZAdresse postale : SALOMON S.A.S. - MAVIC DIVISION 74996 ANNECY • Cedex 9 - FranceTel. +33 (0)4 50 65 71 71 • Fax. +33 (0)4 50 65 71 72 • www.mavic.comMAVIC® is a registered trademark of Salomon S.A.S.Conformité / Conformity CELe symbole CE est utilisé pour indiquer la conformité de ce produitavec les directives 89/336/CEE et 99/5/CEE.The CEE mark is used to mark conformity with the European Uniondirectives 89/336/CEE and 99/5/CEE.

18WINTECH MANAGER The Wintech Manager software enables you to:– Display on a PC all data of each trip coming from the Wintech computer– Organize these data into reports (weekly,monthly,yearly)– Manage up to 3 user accounts– Export the data to share them– Set up your Wintech computer– Customize your Wintech computer’s screens– Get links to external information (website, instruction manual…)– Print and e-mail this information– Store your bike settingsThe Wintech Manager software is compatible with all Wintech models equipped with an integrated USB connection (Wintech USB, Wintech USB Alti, Wintech USB HR and Wintech USB Ultimate).The display of the software may vary according to the version of Wintech computer that you are using:– Elevation information is only available when using a Wintech USB Alti and Wintech USB Ultimate.– Heart rate information is only available when using a Wintech USB HR and Wintech USB Ultimate.20. ENTERING WINTECH MANAGERInstallationInsert the Wintech Manager CD into the CD drive or your PC and simply follow the instructions.If the set up program does not automatically run, navigate the CD contents and double click on the ﬁle “setup.exe”.When the installation is complete, shortcuts are added on the program list of the “Start” menu and on your computer desktop.To launch the software, double click on the “Wintech Manager” icon of your program list or desktop:The ﬁrst time you launch the software, you will be prompted to create a user account. See section 24.1 of this user guide.When a user account has already been created, the software opens on the last active user account. To change user account, see section 24.1 of this user guide.Choose your language to enter the software

1921. DATA TRANSFERWhen the Wintech computer is plugged to the PC, the Wintech Manager software is automatically launched and the download dialog box opens. The data are automatically downloaded and integrated to the last active user account data.If the last trip has not been reset to 0, it will not be downloaded.If you wish to download the Wintech computer data to another user account:1. Open the Wintech Manager software2. Select the user account you wish to download the data to (see section 24.1 of this user guide)3. Plug your Wintech computer to your PC to download the data.If no User has been created yet, select “new user” in the dialog box. The “create new user” screen will be displayed (see section 24.1. of this user guide to create a new user account).As the Wintech computers saves the last 10 trips in its internal memory, all trips that haven’t been downloaded yet will then be added to the Wintech manager database.The clock of the Wintech computer is automatically updated with the clock of the PC each time the Wintech computer is pluged to the PC.Shows downloaded trip reports, by week, month and year (see section 23. Reports of this user guide)Shows downloaded trip details (see section 22. Trip of this user guide)Provides more information on your Wintech computer (see section 26. Links of this user guide)Uploads settings to your Wintech computerStores bike settings information (see section 24. Settings of this user guide)Click “download data” to download the data of your Wintech computer to your PC

2022. TRIPS This screen provides all the details about a speciﬁc trip:– Distance, duration, average and maximum speed, – Average and maximum cadence (if optional cadence sensor used during the trip),– Average and maximum heart rate, time spent in workzone (for Wintech USB HR and Wintech USB Ultimate only, and if heart rate belt used),– Total vertical gain, minimum and maximum elevation, altigraph (distance and elevation graph) (for Wintech USB Alti and Wintech USB Ultimate only),– Details of lap time.Adding a new trip manuallyYou can manually create a new trip by entering data manually (in case you rode without your Wintech computer for instance). Select a day. Select a start time. Manually enter all other informationClick “save” to save this new tripGo to previous or next trip.If multiple trips are recorded on the same day, use these buttons to go to the next or previous trip of the dayChoose the date of the report you wish to consult:– Navigate through the months with left and right arrows – Bold days are the one with trip recorded– Encircled day is current dayNavigation menu: click Home to go back to main menuDelete the current tripPrint the current screenChange user or edit user account (see section 24.1. of this user guide)Saves the trip as a .jpg ﬁleDetail your trip (optional)– Name your trip– Category: choose Racing or Training– Activity: choose Road, Mountain Bike or Home Trainer– Weather: choose Cold, Rainy, Cloudy, Sunny or Hot– Feeling: choose easy, good or hard– Comments: ad personal comments such as places of interest, peloton or alone…Click “save” to save your changessavesavesave

2123. REPORTSWeekly / Monthly reports:Sums up all the trip for a speciﬁc week / month on a graph with – Trip days on the horizontal axis– Trip distance on the vertical axis Yearly report: Sums up all the trip for a speciﬁc year on a graph with – Months on the horizontal axis– Monthly odometer on the vertical axisCumulated distance and number of trip of the year:– Full calendar year for past years– From 1st of January to current day for the current yearSaves the current weekly report as a .jpg ﬁlesaveChoose the second information that will be reported above each trip of the graph, among:– Average speed– Duration– Average cadence (if optional cadence sensor used)– Average heart rate (for Wintech USB HR and Wintech USB Ultimate only, if heart rate belt used)– Total vertical gain (for Wintech USB Alti and Wintech USB Ultimate only)Roll your mouse over a trip to detail the distance and second chosen informationWeek/month numberClick on “week” or “month” to open a calendar and select a new week/monthNavigation menu: click “Home” to go back to main menuChoose among weekly, monthly or yearly reportChoose among weekly, monthly or yearly reportGo to previous or next weekGo to previous or next weekSaves the trip as a .jpg ﬁlesaveChange user or edit user account (see section 24.1. of this user guide)Print the current screenNavigation menu: click “Home” to go back to main menuChange user or edit user account (see section 24.1. of this user guide)Print the current screen

2527. TECHNICAL SPECIFICATIONThe Wintech Manager software can store data coming from 3 diﬀerent users during 10 years , with 300 trips a year of 5 hours each, for each of the 3 users.System requirements:Windows XP or Vista onlyProcessor at 1.3 GHz minimum512 MB of RAM memory50 MB of hard drive disk free space

Navigation menu