NINGBO BAI JIA ELECTRIC APPLIANCE YLT-42A-3C Remote control User Manual 110527 RC 017X3 TR 011 3 US 20140411

NINGBO BAI-JIA ELECTRIC APPLIANCE CO.,LTD Remote control 110527 RC 017X3 TR 011 3 US 20140411

User manual

THANK YOUUSE AND CARE GUIDE3-PACK WIRELESS INDOOR/OUTDOORREMOTE CONTROL SWITCHProduct DescriptionSafety Information1232. Outlet: The outlet located on the bottom of the receiver allows the user to plug an array of devices into it. Plug the light or device to be controlled by the remote into the outlet.Federal Communications Commission Interference StatementThis equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:¨ Reorient or relocate the receiving antenna.¨ Increase the separation between the equipment and the receiver.¨ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.¨ Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. Store indoors when not in use.Operating Instructions¨To activate the receiver, press the “ON” button of the remote control. The green LED of the remote control will illuminate momentarily and the LED of the receiver will remain illuminated.¨To turn the receiver OFF, press the “OFF” button of the remote control. The LED on the receiver will shut off.1 Using the remote controlTroubleshooting Remote control:¨ Channel : To control various devices with three different channels.¨ When the “ON” button is pressed, it will override the program to on function.¨ When the “OFF” button is pressed, it will override the program to off function.Maintenance2 Replacing the battery¨Remove the battery compartment cover from the back of the remote control by sliding the cover in the direction that its threads curve.¨Remove the old battery and place a new DC 3V CR2032 battery into the battery compartment, correctly observing the polarity indications (+/−) inside the battery compartment.¨Replace the battery compartment cover.¨Dispose or recycle spent/discharged batteries in compliance with all applicable laws. For detailed information, contact your local solid waste authority.RATINGS125 VAC, 60 Hz15 A General Purpose15 A Resistive1000 W Tungsten1/3 HP MotorNOTE: This product is suitable for outdoor use and use in damp locations. 1. Power indicator light:The power indicator lightindicates that the receiver is on.¨To set up the three receivers (outlets) with various devices, locate channel 1, 2, 3, on the remote control and the 1, 2, 3, on each receiverand select ON/OFF function with the same channel (1,2,3)respectively.¨Mount the receiver on a wall near a grounded electrical outlet. The nailor screw head must extend at least 3/16 in. out from the wall. Hang the receiver from the slot on the back of the unit onto a nail or screw. Plug the power supply cord of the receiver into the outlet. ¨Plug the device cord into the receptacle at the bottom of thereceiver.¨Installation InstructionsInstallation Instructions3.noituloSmelborPThe lights do not turn on and off via remote control.Confirm remote operation after replacingbatteries.The lights do not turn on, evenwhen the power indicator lightindicates that the receiver is on.Ensure the lights are functional byplugging them directly into the outlet. Be sure that the lights are in the “ON”position if they have their own switch. Be sure that the outlet that the receiveris plugged into is active. 3WARNING: The device must be mounted in a vertical positionwith the receptacle facing downward and with the receptacle atleast 2 ft. above the ground level to prevent water immersion. WARNING: Do not mutilate or place the battery in a fire. The battery may burst or release toxic materials. Do not short circuit or reverse polarity as this may cause burns.We appreciate the trust and confidence you have placed inDefiant through the purchase of this outdoor wireless remote control.Visit us online to see our full line of products available for your homeimprovement needs. Thank you for choosing Defiant!Made in ChinaSAVE THESE INSTRUCTIONS!1 2 3Remove the insulation tab from the battery compartment.Remote does not turn the device on or off.Receiver and transmitter need to be re-synched.Replug the reciever into a properly gounded outletgreen indicator flash on the reciever, then press the Model: YLT-42A-3Cand within 15 seconds,press and hold the OFF(2) button on the transmitter for 1.5 seconds untill theON(2) botton.Information concernant l'exposition à l'énergie radiofréquenceVotre appareil est con u et fabriqué pour ne pas dépasser les limites d'émission pour l'exposition à l'énergie RF établie par le gouvernement du Canada (IC). Les informations sur votre appareil sont en fichier avec l'IC et peuvent être trouvées sous la section Affichage Grant de https://sms-sgs.ic.gc.ca/equipmentRechercher après la recherche sur l'IC pour votre appareil, qui se trouve sur le l'arrière de l'appareil.This device complies with part 15 of FCC rule and Industry Canada: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including license-exempt RSS standard(s).Operation is subject to the following two conditionsinterference that may cause undesired operation.Avis d'Industrie Canada (IC): Cet appareil est conforme avec Industrie Son fonctionnement est soumisaux deux conditions suivantes: (2) cet appareil doit accepter toute interférence, y compris celles Canada exempts de licence standard RSS (s). (1) cet appareil ne doit pas provoquer d'interférences et pouvant causer un mauvais fonctionnement de l'appareil.

Navigation menu