Musical Electronics RX-DBT30 Portable Stereo CD System User Manual P1

Musical Electronics Ltd Portable Stereo CD System P1

user manual.pdf

GAOperating Instructions Operations in these instructions are described with controls on the main unit. Your unit may not look exactly the same as illustrated.Thank you for purchasing this product.Dear CustomerPortable Stereo CD SystemModel No. RX-DBT30For optimum performance and safety, please read these instructionsthoroughly before connecting, operating or adjusting this product.Please keep this manual for future reference.BluetoothRQT9967-G
CAUTION!WARNING:Product ldentification Marking is located on the bottom of the unit.If this unit is not used for a long period of time or Use of batteriesAvoid using or placing this unit near sources or heat. Do not leave it in an automobile exposed to direct sunlight for a long time with the doors and windows closed as this may deform the cabinet.Avoid cuts, scratches, or poor connections in the AC mains lead, as they may result in possible fire or electric shock hazard. Also, excessive bending, pulling or splicing of the lead should be avoided.Do not unplug the AC adaptor by pulling on the lead. To do so may cause premature failure or shock hazard.Do not operate this unit in a bathroom, as a potential shock hazard may result.When not in use, disconnect the AC mains lead from the household mains socket.Safety precautionsIf this unit is not used for a long period of time or is used only from an AC power source, remove all the batteries to prevent potential damage due to possible battery leakage. Make sure to match the + and – on each battery to the + and – signs in the unit battery compartment. Do not mix old and new batteries. Do not use different types of batteries at the same time. Do not take apart or short circuit the batteries. Do not attempt to recharge alkaline or manganese batteries. Do not use batteries if the covering has been peel off. Do not heat or expose to flame. Do not leave the battery(ies) in a car exposed to direct sunlight for a long period of time with doors and windows closed., Mishandling of batteries can cause electrolyte leakage which may cause a fire.CAUTION!Danger of explosion if battery is incorrectly replaced. Replace only with the type recommended by the manufacturer.When disposing of the batteries, please contact your local authorities or dealer and ask for the correct method of disposal. This unit utilizes a laser. Use of controls or adjustmentsor performance of procedures other than those specifiedherein may result in hazardous radiation exposure. To reduce the risk of fire, electric shock or product damage, Do not expose this unit to rain, moisture, dripping or splashing. Do not place objects filled with liquids, such as vases, on this unit. Use only the recommended accessories. Do not remove covers. Do not repair this unit by yourself. Refer servicing to qualified service personnel. CAUTION!To reduce the risk of fire, electric shock or product damage, Do not install or place this unit in a bookcase, built-in cabinet or in another confined space. Ensure this unit is well ventilated. Do not obstruct this unit’s ventilation openings with newspapers, tablecloths, curtains and similar items. Do not place sources of naked flames, such as lighted candles, on this unit.The mains plug is the disconnecting device.Install this unit so that the mains plug can be unplugged fromthe socket outlet immediately. This unit is intended for use in moderate climates. This unit is intended for use in tropical climates.Oceania & Israel South East AsiaThis unit may receive radio interference caused by mobile telephones during use. If such interference occurs, pleaseincrease separation between this unit and mobile telephone. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. SURGE PROTECTORS: It is recommended to use a surge protector for AC connection. Lightning and power surges ARE NOT covered under warranty for this product. Compliance with FCCregulationhelp.
Power SourcesUsing the household mains socket Using the household mains socket To household mains socketAC power adaptor (included)Connect the DC cord of the AC power adaptor firmly to the unit and connect the suitable AC mains lead firmly to the household mains socket.NoteThe included AC power adaptor is for use with this unit only. Do not use it with other equipment.This unit can be powered by either the included AC power adaptor, or by using six “C” sized alkaline batteries (not included). This unit only operates on batteries when the AC power adaptor is unplugged.Use only alkaline batteries.Using batteries (not included)Using batteries (not included)USB charging portUSB charging portVVAC mains lead(included)3When the battery indicator begins flashing, replace all six of thebatteries.When to change the batteriesWhen to change the batteriesThis CD system included a USB port placed on the rear.The USB port supports powering and charging most USB devices. (USB cable sold separately).Supplied accessoriesCheck and identity the supplied accessories. 3 x AC mains lead For Australia, New ZealandFor ThailandFor Singapore, Malaysia, Israel 1 x AC AdaptorPanasonic CorporationMade in ChinaModel No. RX-DBT30Portable Stereo CD System6 LR14 BATTERIES 9VDC IN 9V 1.8A Press towards while inserting the battery.(LR14, C)+_+_+_123456Table of contentsSafety precautions .................................................. Maintenance ............................................................ Use of batteries .......................................................Power sources ........................................................Overview of controls ..............................................Using your CD system ...........................................Pairing with a Bluetooth device ...........................Playing audio from a Bluetooth device ...............To play the radio .....................................................Setting radio station presets ................................. 6Playing audio from a connected audio device ....To play a CD ............................................................To control CD playback .........................................Repeating a track or CD ........................................To play tracks in random order ............................22234555566666Program CD/MP3 playback ...................................Compatible CD .......................................................Compatible MP3 files .............................................About Bluetooth ....................................................7778Troubleshooting guide .......................................... Specifications ........................................................ 9 910Warranty ................................................................®®®Supplied accessories ............................................. 3
Standby/on switch
Using your CD system To turn your CD system unit on or off• Press [ ] power button.Selecting the audio source/• Press the [Source] button one or more times until the audio source you want appears on the LCD. You can select:• FM – FM radio band• AM – AM radio band• CD – CD player• – Paired Bluetooth device AUX IN – Device connected to the AUX IN jack. • Selecting the sound modeYou can select a sound (equalizer) mode to automaticallyadjust the sound for the type of music you are playing.• Press the [Sound] button one or more times until the sound mode you want appears on the LCD. You can select JAZZ, POP, CLASSIC, ROCK.To pair with a Bluetooth device1. On your CD System, press the [Source] one or more times until the “ ” indicator appears of the LCD.2. Make sure that your Bluetooth device is turned on and within 33 feet (10 meters) of your CD System.3. On your CD System, press the [ ] Bluetooth pairing button. Your CD System enters pairing mode, and the Bluetooth LED blinks. Your CD System remains in pairing mode for 19 minutes or until it pairs with a Bluetooth device. 4. On the Bluetooth device, start pairing mode, then select “RX-DBT30”. See the instructions that came with the device for information pairing.5. If you are asked for a password, enter 0000. When pairing is complete, the Bluetooth LED on your CD System lights solid.6. To disconnect from the paired Bluetooth device, press and hold the [ ] Bluetooth pairing button on your CD System for three seconds and it will display “CLEAN BT”. Your CD System disconnects from the Bluetooth device and enters pairing mode again.7. To reconnect your CD System to a paired device, search for and select “RX-DBT30” on the Bluetooth device while the CD System is in pairing mode. Note: Your CD System can store pairing information for eight devices. When your CD System is in Bluetooth pairing mode, it automatically reconnects to the last paired device mode, and within 33 feet (10 meters) of your CD System. If you want to reconnect with another previously paired device, make sure the device is within range, turn it on, and put it in pairing mode. Then press the [ ] Bluetooth pairing button. Your CD System searches for the pairing information and pairs with the device. Pairing with a Bluetooth device 5when the device is turned on, in Bluetooth pairing ®®®®®® ® ® ® ® Playing audio from a Bluetooth device To play audio from a Bluetooth device1. On your CD System, press the [Source] button one or more times until the “ ” indicator appears on the LCD.2. Make sure that the Bluetooth device has been paired to your CD System. See “Pairing with a Bluetooth device” section.3. To control playback from the Bluetooth device, on your CD System: Press the [ ] play/pause button to start or pause playback. Your CD System plays the audio files on the Bluetooth device. Rotate the [Volume] knob to increase or decrease the volume. Press the skip forward button to go to the next song. Press and hold this button to fast forward. To play the radio /1. Press the [ ] power button to turn on your CD System.2. Press the [Source] button one or more times until “AM”, “FM” appears on the LCD. 3. Press the skip forward or skip backward button to go to the next higher or lower radio frequency. When your CD System detects a strong FM signal, “STEREO” appears on the LCD. OR Press and hold the skip forward or skip backward button for two second to automatically tune to the next higher or lower radio station. 4. Rotate the [Volume] knob to increase or decrease the volume.Note: To improve reception: For FM reception, raise and extend the FM antenna. You may have to reposition the antenna for best reception. For AM reception, turn your CD System slightly until reception improves. If the power AC adapter is connected to the power outlet, move the CD System away from the AC adaptor. [Tune +/ ][Tune +/ ][Tune / ] ][Tune / __ /[Tune +/ ] If the current song has played less than two seconds, press the skip backward button to go to the previous song. If the song has played more than two seconds, press this button to go to the beginning of the song. Press and hold this button to fast reverse. [Tune / ]_®®®® ® ® ® ® ® ® ® Press button to stop playback.[ ] Note: Can’t activate PLAY MODE & PROGRAMfunction at Bluetooth mode.
“ ”“ ”blinks on the LCD.
This function allows you to program up to 20 tracks for CD and MP3 files to be played in the desired order.When 20 tracks have programmed. The LCD will show “FULL” for three seconds.Note:Programming can only be performed when playbackis stopped.1. In stop mode, press the [Memory/Program] button. The track number “P01 000” will show on LCD.2. Press the or button to select a track number.3. Press the [Memory/Program] button to confirm.4. Repeat steps 2 and 3 to program other tracks.5. To play the program, press the [ ] play/pause button. 6. In play mode, press the [ ] button once to go back to the program mode and the total program tracks will show on LCD.7. In stop mode, to clear display the program and then press the [ ] stop button, the LCD will show “CLEAR” for three seconds and exit to normal.Note:In MP3 mode press [Memory/Program] button to display ID3 information for one cycle and then show back to play mode.When ID3 is scrolling, press [Memory/Program]button, the LCD will show back to playtime at once. [Tune+ / ] [Tune / ]_Compatible CDA disc with the CD Logo.This unit can playback discs that conform to the CD-DA format.This unit may not be able to play some discs due to the condition of the recording.Note about using a Dual DiscThe digital audio content side of a Dual Disc does not meet the technical specifications of the Compact Disc Digital Audio (CD-DA) format so playback may not be possible.Note on CDsThis unit can access up to 99 tracks.This unit can play MP3 files and CD-R/RW due to the condition of the recording.Do not use irregularly shaped disc.Do not use disc with labels and stickers that are coming off or with adhesive exuding from under labels and stickers.Do not attach extra labels or stickers on the disc.Do not write anything on the disc.Compatible MP3 filesSupported format: files with the extension “mp3” or “MP3”.Compatible compression rate : Between 16 kbps and 320 kbps (stereo).Depending on how you create the MP3 files. They may not play in the order you numbered them or may not play at all.CD-R/RWMaximum number of tracks and albums: 999 tracks and 999 albums (Excluding Root folder).Disc formats : - ISO9660 level 1 and level 2 (except for extended formats).If the disc includes both MP3 and normal audio data (CD-DA), the unit plays the type recorded in the inner part of the disc.This unit cannot play files recorded using packet write.Note on MP3Files are treated as tracks and folders are treated as albums.This unit can access up to 999 tracks, 999 albums.Disc must conform to ISO9660 level 1 or 2 (except for extended formats).To play in a certain order, prefix the folder and file names with 3-digits numbers in the order you want to play them.Limitations on MP3 playIf you have record MP3 on the same disc as CD-DA, only the format recorded in the first session can be played.Some MP3s may not be played due to the condition of the disc or recording.Recordings will not necessarily be played in the order you recorded them.7- Does not support files recorded in Universal Disc Format (UDF).It does not support MP3 album selection.Auto offThis unit will turn to Standby mode automatically ifthere is no sound and it is not being used for approximately 19 minutes.
CD contains notsupported dataRefer to compatibilityon page 7the
Power supply DC 9V (DC IN terminal)zzmThe Bluetooth word mark and logos are registeredtrademarks owned by Bluetooth SIG, Inc. and any use ofsuch marks by Panasonic Corporation is under license.Panasonic cannot be held responsible for data and/orinformation that can possibly be compromised during a wireless transmission.FThis system conforms to the frequency restrictions:- Taking apart or modifying the main unit.-unit is located too close to other Bluetoothlaboratories, etc.).this system withRestrictions of use
Panasonic Warranty 1. The product is warranted for 12 months from the date of purchase. Subject to the conditions of this warranty Panasonic or its Authorised Service Centre will perform necessary service on the product without charge for parts or labour, if in the opinion of Panasonic, the product is found to be faulty within the warranty period. 2. This warranty only applies to Panasonic products purchased in Australia and sold by Panasonic Australia or its Authorised Distributors or Dealers and only where the products are used and serviced within Australia or it’s territories. Warranty cover only applies to service carried out by a Panasonic Authorised Service Centre and only if valid proof of purchase is presented when warranty service is requested. 3. This warranty only applies if the product has been installed and used in accordance with the manufacturer’s recommendations ( (as noted in the operating instructions) under normal use and reasonable care (in the opinion of Panasonic). The warranty covers normal domestic use only and does not cover damage, malfunction or failure resulting from use of incorrect voltages, incorrect installation, accident, misuse, neglect, build-up of dirt or dust, abuse, maladjustment of customer controls, mains supply problems, thunderstormactivity, infestation by insects or vermin, tampering or repair by unauthorised persons (including unauthorised alterations), introduction of sand, humidity or liquids, commercial use such as hotel, office, restaurant, or other business or rental use of the product, exposure to abnormally corrosive conditions or any foreign object or matter having entered the product. 5. Some products may be supplied with Ethernet connection hardware. The warranty is limited on such products and will not cover 6. To claim warranty service, when required, you should: 7. The warranties hereby conferred do not extend to, and exclude, any costs associated with the installation, de-installation orre-installation of a product, including costs related to the mounting, de-mounting or remounting of any screen, (and any other ancillary activities), delivery, handling, freighting, transportation or insurance of the product or any part thereof replacement of anddo not extend to, and exclude, any damage or loss occurring by reason of, during, associated with, or related to such installation,de-installation, re-installation or transit. Panasonic Authorised Service Centres are located in major metropolitan areas and most regional centres of Australia, however, coverage will vary dependant on product. For advice on exact Authorised Service Centre locations for your product, please telephoneour Customer Care Centre on 132600 or visit our website and use the Service Centre Locator.In addition to your rights under this warranty, Panasonic products come with consumer guarantees that cannot be excluded under the Australian Consumer Law. If there is a major failure with the product, you can reject the product and elect to have a refund or to have the product replaced or if you wish you may elect to keep the goods and be compensated for the drop in value of the goods. You are also entitled to have the product repaired or replaced if the product fails to be of acceptable quality and the failure does not amount to amajor failure.If there is a major failure in regard to the product which cannot be remedied then you must notify us within a reasonable period by contacting the Panasonic Customer Care Centre. If the failure in the product is not a major failure then Panasonic may choose to repairor replace the product and will do so in a reasonable period of time from receiving notice from you.If you require assistance regarding warranty conditions or any other enquiries, please visit the Panasonic Australiawebsite www.panasonic.com.au or contact by phone on 132 600 If phoning in, please ensure you have your operating instructions available.(a) Internet and or DLNA connection / setup related problems (b) Access fees and or charges incurred for internet connection The use of incompatible software or software not specifically stipulated in the product operations manual; and(d) Any indirect or consequential costs associated with the incorrect use or misuse of the hardware, its connection to the internet or any other device.4. This warranty does not cover the following items unless the fault or defect existed at the time of purchase: s fcsiD elbadroceR ro yar-u-lB ,DVD (e) rt(s)aP tenibaC (a) (b) Video or Audio Tapes Video / Audio Heads from wear and tear in normal use (c) SD cards or USB devices (c) (g) Information stored on Hard Disk Drive, USB stick or SD card (d) User replaceable Batteries (h) DTV reception issues caused by TV Aerial / Cabling / Wall socket(s) etcTelephone Panasonic’s Customer Care Centre on 132600 or visit our website referred to below and use the Service Centre Locator for the name/address of the nearest Authorised Service Centre. Send or take the product to a Panasonic Authorised Service Centre together with your proof of purchase receipt as a proof of purchase date. Please note that freight and insurance to and / or from your nearest Authorised Service Centre must be arranged by you. Note that home or pick-up/delivery service is available for the following products in the major metropolitan areas of Australia or the normal operating areas of the nearest Authorised Service Centres: Plasma/LCD televisions / displays (screen size greater than 103 cm)THIS WARRANTY CARD AND THE PURCHASE DOCKET (OR SIMILAR PROOF OF PURCHASE) SHOULD BE RETAINED BY THE CUSTOMER AT ALL TIMESPanasonic Australia Pty. LimitedACN 001 592 187 ABN 83 001 592 1871 Innovation Road, Macquarie Park NSW 2113 PRO-031-F11 Issue: 4.010( ) 01-01-2011Limited Warranty ( ONLY FOR AUSTRALIA)
RQT9967-G

Navigation menu