Motorola Solutions 99FT3093 VHF Portable 2-Way Radio User Manual Manual

Motorola Solutions, Inc. VHF Portable 2-Way Radio Manual

Contents

Manual

PROFESSIONAL DIGITAL TWO-WAY RADIOSMOTOTRBOTMXPRTM 7550 ISCOLOR DISPLAY PORTABLEUSER GUIDE
Declaration of ConformityEnglishiDeclaration of ConformityThis declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below.DECLARATION OF CONFORMITYPer FCC CFR 47 Part 2 Section 2.1077(a)Responsible Party Name: Motorola Solutions, Inc.Address: 1303 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A.Phone Number: 1-800-927-2744Hereby declares that the product:Model Name: XPR 7550 ISconforms to the following regulations:FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a)Class B Digital DeviceAs a personal computer peripheral, this device complies with Part 15 of the FCC Rules. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
Declaration of ConformityEnglishiiNote: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.
ContentsEnglishiiiContentsThis User Guide contains all the information you need to use the MOTOTRBO XPR Series Digital Portable Radios.Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . iImportant Safety Information . . . . . . . . . . . . . . . . . ixProduct Safety and RF Exposure Compliance . . .ixSoftware Version . . . . . . . . . . . . . . . . . . . . . . . . . . . ixComputer Software Copyrights . . . . . . . . . . . . . . . . xHandling Precautions . . . . . . . . . . . . . . . . . . . . . . . xiGetting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . 1What Your Dealer/System Administrator Can Tell You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Preparing Your Radio for Use . . . . . . . . . . . . . . . . . . 2Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 2Attaching the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 3Attaching the Antenna . . . . . . . . . . . . . . . . . . . . . . . . 3Attaching the Belt Clip . . . . . . . . . . . . . . . . . . . . . . . . 4Attaching the Universal Connector Cover (Dust Cover) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Powering Up the Radio . . . . . . . . . . . . . . . . . . . . . . . 5Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . 5Identifying Radio Controls . . . . . . . . . . . . . . . . . . . . 6Radio Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Programmable Buttons . . . . . . . . . . . . . . . . . . . . . . . 7Assignable Radio Functions . . . . . . . . . . . . . . . . . 7Assignable Settings or Utility Functions . . . . . . . . . 9Using the 4-Way Navigation Button . . . . . . . . . . . . 10Accessing the Programmed Functions . . . . . . . . . . 10Using the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . 11Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . . . 12Switching Between Conventional Analog and Digital Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13IP Site Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Capacity Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Linked Capacity Plus . . . . . . . . . . . . . . . . . . . . . . . 15Identifying Status Indicators . . . . . . . . . . . . . . . . . . 16Display Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Call Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Advanced Menu Icons . . . . . . . . . . . . . . . . . . . . . . 18Mini Notice Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Sent Item Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . 19LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Indicator Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Audio Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Making and Receiving Calls . . . . . . . . . . . . . . . . . . 22Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
ContentsEnglishivSelecting a Channel . . . . . . . . . . . . . . . . . . . . . . . . 23Receiving and Responding to a Radio Call . . . . . . 24Receiving and Responding to a Group Call . . . . 24Receiving and Responding to a Private Call . . . 25Receiving an All Call . . . . . . . . . . . . . . . . . . . . . . 25Receiving and Responding to a Selective Call . . 26Receiving and Responding to a Phone Call . . . . 27Phone Call as a Private Call . . . . . . . . . . . . . . 27Phone Call as a Group Call . . . . . . . . . . . . . . . 27Phone Call as an All Call . . . . . . . . . . . . . . . . . 28Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . 28Making a Call with the Channel Selector Knob . . 29Making a Group Call . . . . . . . . . . . . . . . . . . . . 29Making a Private Call . . . . . . . . . . . . . . . . . . . 30Making an All Call . . . . . . . . . . . . . . . . . . . . . . 31Making a Selective Call . . . . . . . . . . . . . . . . . 31Making a Phone Call with the One Touch Access Button . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Making a Group, Private or All Call with the Programmable Number Key . . . . . . . . . . . . . . . 33Making a Phone Call with the Programmable Phone Button . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Making a Call with the Programmable Manual Dial Button . . . . . . . . . . . . . . . . . . . . . . . 36Making a Private Call . . . . . . . . . . . . . . . . . . . . 36Making a Phone Call . . . . . . . . . . . . . . . . . . . . 36Stopping a Radio Call . . . . . . . . . . . . . . . . . . . . . . 38Talkaround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Monitoring Features . . . . . . . . . . . . . . . . . . . . . . . . 39Monitoring a Channel . . . . . . . . . . . . . . . . . . . . . 39Permanent Monitor . . . . . . . . . . . . . . . . . . . . . . . 39Advanced Features . . . . . . . . . . . . . . . . . . . . . . . . . 40Radio Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Sending a Radio Check . . . . . . . . . . . . . . . . . . . 41Remote Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Initiating Remote Monitor . . . . . . . . . . . . . . . . . . 42Stopping Remote Monitor . . . . . . . . . . . . . . . . . . 43Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Viewing an Entry in the Scan List . . . . . . . . . . . . 44Viewing an Entry in the Scan List by Alias Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Editing the Scan List . . . . . . . . . . . . . . . . . . . . . . 45Adding a New Entry to the Scan List . . . . . . . . 45Deleting an Entry from the Scan List . . . . . . . . 46Setting and Editing Priority for an Entry in the Scan List . . . . . . . . . . . . . . . . . . . . . . . . 47Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Starting and Stopping Scan . . . . . . . . . . . . . . . . 48Responding to a Transmission During a Scan . . 49Deleting a Nuisance Channel . . . . . . . . . . . . . . . 49Restoring a Nuisance Channel . . . . . . . . . . . . . . 49
ContentsEnglishvVote Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Contacts Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 50Making a Group Call from Contacts . . . . . . . . . . . 51Making a Private Call from Contacts . . . . . . . . . 52Making a Phone Call from Contacts . . . . . . . . . . 53Making a Call by Alias Search . . . . . . . . . . . . . . 55Assigning an Entry to a Programmable Number Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Removing the Association between Entry and Programmable Number Key . . . . . . . . . . . . . . . . 57Setting Default Contact . . . . . . . . . . . . . . . . . . . . 57 Adding a New Contact . . . . . . . . . . . . . . . . . . . . 58Call Indicator Settings . . . . . . . . . . . . . . . . . . . . . . . 58Activating or Deactivating Call Ringers for Call Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58Activating or Deactivating Call Ringers for Private Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59Activating or Deactivating Call Ringers for Selective Call . . . . . . . . . . . . . . . . . . . . . . . . . . . 59Activating or Deactivating Call Ringers for Text Message . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Activating or Deactivating Call Ringers for Telemetry Status with Text . . . . . . . . . . . . . . . . . 60Assigning Ring Styles . . . . . . . . . . . . . . . . . . . . . 61Escalating Alarm Tone Volume . . . . . . . . . . . . . . 61Call Log Features . . . . . . . . . . . . . . . . . . . . . . . . . . 62Viewing Recent Calls . . . . . . . . . . . . . . . . . . . . . . 62Storing an Alias or ID from a Call List . . . . . . . . . 62Deleting a Call from a Call List . . . . . . . . . . . . . . 62Viewing Details from a Call List . . . . . . . . . . . . . . 63Call Alert Operation . . . . . . . . . . . . . . . . . . . . . . . . . 63Receiving and Responding to a Call Alert . . . . . . 63Making a Call Alert from the Contacts List . . . . . . 64Making a Call Alert with the One Touch Access Button . . . . . . . . . . . . . . . . . . 64Emergency Operation . . . . . . . . . . . . . . . . . . . . . . . 65Receiving an Emergency Alarm . . . . . . . . . . . . . 65Responding to an Emergency Alarm . . . . . . . . . . 66Sending an Emergency Alarm . . . . . . . . . . . . . . . 66Sending an Emergency Alarm with Call . . . . . . . 67Sending an Emergency Alarm with Voice to Follow . . . . . . . . . . . . . . . . . . . . . . . . . . 68Reinitiating an Emergency Mode . . . . . . . . . . . . . 70Exiting Emergency Mode . . . . . . . . . . . . . . . . . . . 70 Man Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71Text Message Features . . . . . . . . . . . . . . . . . . . . . 72Writing and Sending a Text Message . . . . . . . . . 72Sending a Quick Text Message . . . . . . . . . . . . . . 73Sending a Quick Text Message with the One Touch Access Button . . . . . . . . . . . . . . . . . . 74Accessing the Drafts Folder . . . . . . . . . . . . . . . . . 74Viewing a Saved Text Message . . . . . . . . . . . . 74
ContentsEnglishviEditing and Sending a Saved Text Message . . 75Deleting a Saved Text Message from Drafts . . 75Managing Fail-to-Send Text Messages . . . . . . . 76Resending a Text Message . . . . . . . . . . . . . . . 76Forwarding a Text Message . . . . . . . . . . . . . . 76Editing a Text Message . . . . . . . . . . . . . . . . . . 77Managing Sent Text Messages . . . . . . . . . . . . . 77Viewing a Sent Text Message . . . . . . . . . . . . . 78Sending a Sent Text Message . . . . . . . . . . . . . 78Deleting All Sent Text Messages from Sent Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79Receiving a Text Message . . . . . . . . . . . . . . . . . 80Reading a Text Message . . . . . . . . . . . . . . . . . . 80Managing Received Text Messages . . . . . . . . . . 80Viewing a Text Message from the Inbox . . . . . 81Viewing a Telemetry Status Text Message from the Inbox . . . . . . . . . . . . . . . . . . . . . . . . . 81Replying to a Text Message from the Inbox . . 81Deleting a Text Message from the Inbox . . . . . 82Deleting All Text Messages from the Inbox . . . 83Analog Message Encode . . . . . . . . . . . . . . . . . . . 83Sending MDC Message Encode to Dispatcher . . 83Analog Status Update . . . . . . . . . . . . . . . . . . . . . . 84Sending Status Update to Predefined Contact . . 84Privacy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84Dual Tone Multi Frequency (DTMF) . . . . . . . . . . . . 85Multi-Site Controls . . . . . . . . . . . . . . . . . . . . . . . . . 86Starting an Automatic Site Search . . . . . . . . . . . 86Stopping an Automatic Site Search . . . . . . . . . . 87Starting a Manual Site Search . . . . . . . . . . . . . . 87Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88Radio Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . 88Radio Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . 89Lone Worker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90Password Lock Features . . . . . . . . . . . . . . . . . . . . 91Accessing the Radio from Password . . . . . . . . . 91Unlocking the Radio from Locked State . . . . . . . 91Turning the Password Lock On or Off . . . . . . . . . 92Changing the Password . . . . . . . . . . . . . . . . . . . 92 Notification List . . . . . . . . . . . . . . . . . . . . . . . . . . . 93Accessing the Notification List . . . . . . . . . . . . . . 93Auto-Range Transponder System (ARTS) . . . . . . . 94Over-the-Air Programming (OTAP) . . . . . . . . . . . . 94Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95Turning the Radio Tones/Alerts On or Off . . . . . 95Turning Keypad Tones On or Off . . . . . . . . . . . . 95Setting the Tone Alert Volume Offset Level . . . . 96Turning the Talk Permit Tone On or Off . . . . . . . 96Turning the Power Up Tone On or Off . . . . . . . . 97Changing the Display Mode . . . . . . . . . . . . . . . . 97Adjusting the Display Brightness . . . . . . . . . . . . 98
ContentsEnglishviiControlling the Display Backlight . . . . . . . . . . . . . 98Setting the Squelch Level . . . . . . . . . . . . . . . . . . 99Turning the Introduction Screen On or Off . . . . . . 99Locking and Unlocking the Keypad . . . . . . . . . . 100Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100Setting the Text Message Alert Tone . . . . . . . . 100Turning the LED Indicator On or Off . . . . . . . . . 101Turning the Voice Operating Transmission (VOX) Feature On or Off . . . . . . . . . . . . . . . . . . 101Turning the Option Board Feature(s) On or Off . 102Identifying Cable Type . . . . . . . . . . . . . . . . . . . . 102Voice Announcement . . . . . . . . . . . . . . . . . . . . . 103Call Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . 103Menu Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104Analog Mic AGC (Mic AGC-A) . . . . . . . . . . . . . . 104Digital Mic AGC (Mic AGC-D) . . . . . . . . . . . . . . 104Intelligent Audio . . . . . . . . . . . . . . . . . . . . . . . . . 105GPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105Text Entry Configuration . . . . . . . . . . . . . . . . . . 106Word Correct . . . . . . . . . . . . . . . . . . . . . . . . . 106Word Predict . . . . . . . . . . . . . . . . . . . . . . . . . . 107Sentence Cap . . . . . . . . . . . . . . . . . . . . . . . . . 107Viewing Custom Words . . . . . . . . . . . . . . . . . 108Editing Custom Word . . . . . . . . . . . . . . . . . . . 108Adding Custom Words . . . . . . . . . . . . . . . . . . 108Deleting a Custom Word . . . . . . . . . . . . . . . . 109Deleting All Custom Words . . . . . . . . . . . . . . . 109Accessing General Radio Information . . . . . . . . 110Accessing the Battery Information . . . . . . . . . 110Checking the Radio Alias and ID . . . . . . . . . . 110Checking the Firmware Version and Codeplug Version . . . . . . . . . . . . . . . . . . . . . . 111Checking the GPS Information . . . . . . . . . . . . 111Software Update . . . . . . . . . . . . . . . . . . . . . . . 112Site Information . . . . . . . . . . . . . . . . . . . . . . . 112RSSI Values . . . . . . . . . . . . . . . . . . . . . . . . . . . 112Front Panel Configuration (FPC) . . . . . . . . . . . . . 113Entering FPC Mode . . . . . . . . . . . . . . . . . . . . . . 113Editing FPC Mode Parameters . . . . . . . . . . . . . 113Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114Carry Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115Earbuds and Earpieces . . . . . . . . . . . . . . . . . . . . . 115Headsets and Headset Accessories . . . . . . . . . . . 115Remote Speaker Microphones . . . . . . . . . . . . . . . 115Miscellaneous Accessories . . . . . . . . . . . . . . . . . . 115Appendix: Maritime Radio Use in the VHF Frequency Range . . . . . . . . . . . . . . . . . . . . . . 116Special Channel Assignments . . . . . . . . . . . . . . . 116
ContentsEnglishviiiEmergency Channel . . . . . . . . . . . . . . . . . . . . . 116Non-Commercial Call Channel . . . . . . . . . . . . . 116Operating Frequency Requirements . . . . . . . . . . 117Declaration of Compliance for the Use of Distress and Safety Frequencies . . . . . . . . . . . . 119Technical Parameters for Interfacing External Data Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . 119Batteries and Chargers Warranty . . . . . . . . . . . . 120Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Important Safety InformationEnglishixImportant Safety InformationProduct Safety and RF Exposure ComplianceATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the (Motorola Publication part number 68009584001) to ensure compliance with RF energy exposure limits and CSA Safety Leaflet (Motorola Publication part number 68012006018). Keep the Quick Reference Guide available to all users of the radio. For a list of Motorola-approved antennas, batteries, and other accessories, visit the following website: http://www.motorolasolutions.comAny modification to this device, not expressly authorized by Motorola, may void the safety and regulatory compliance of the radio. The radio must only be repaired or serviced at authorized Motorola Service Centers. Contact your dealer or system administrator for details. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.This radio transmitter has been approved by Industry Canada to operate with Motorola-approved antenna with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio.
Software VersionEnglishxSoftware VersionAll the features described in the following sections are supported by the radio's software version R02.06.10. See Checking the Firmware Version and Codeplug Version on page 111 to determine your radio's software version. Check with your dealer or system administrator for more details of all the features supported.Computer Software CopyrightsThe Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, reproduced, modified, reverse-engineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive license to use that arises by operation of law in the sale of a product.The AMBE+2TM voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Communications Equipment. The user of this Technology is explicitly prohibited from attempting to decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. U.S. Pat. Nos. #5,870,405, #5,826,222, #5,754,974, #5,701,390, #5,715,365, #5,649,050, #5,630,011, #5,581,656, #5,517,511, #5,491,772, #5,247,579, #5,226,084 and #5,195,166.
Handling PrecautionsEnglishxiHandling PrecautionsThe MOTOTRBO Series Digital Portable radio meets IP57 specifications, allowing the radio to withstand adverse field conditions such as being submersed in water.•If the radio has been submersed in water, shake the radio well to remove any water that may be trapped inside the speaker grille and microphone port. Trapped water could cause decreased audio performance.•If the radio’s battery contact area has been exposed to water, clean and dry battery contacts on both the radio and the battery before attaching the battery to the radio. The residual water could short-circuit the radio.•If the radio has been submersed in a corrosive substance (e.g. saltwater), rinse the radio and battery in fresh water then dry the radio and battery.•To clean the exterior surfaces of the radio, use a diluted solution of mild dishwashing detergent and fresh water (i.e. one teaspoon of detergent to one gallon of water).•Never poke the vent (hole) located on the radio chassis below the battery contact. This vent allows for pressure equalization in the radio. Doing so may create a leak path into the radio and the radio’s submersibility may be lost.•Never obstruct or cover the vent, even with a label. •Ensure that no oily substances come in contact with the vent.•The radio with antenna attached properly is designed to be submersible to a maximum depth of 1 meter (3.28 feet) and a maximum submersion time of 30 minutes. Exceeding either maximum limit or use without antenna may result in damage to the radio.•When cleaning the radio, do not use a high pressure jet spray on the radio as this will exceed the 1 meter depth pressure and may cause water to leak into the radio. Do not disassemble the radio. This could damage radio seals and result in leak paths into the radio. Radio maintenance should only be done in service depot that is equipped to test and replace the seal on the radio.
NotesEnglishxiiNotes
Getting StartedEnglish1Getting StartedTake a moment to review the following:How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . . . page 1What Your Dealer/System Administrator Can Tell You. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1How to Use This GuideThis User Guide covers the basic operation of the MOTOTRBO Portables.However, your dealer or system administrator may have customized your radio for your specific needs. Check with your dealer or system administrator for more information.Throughout this publication, the icons below are used to indicate features supported in either the conventional Analog mode or conventional Digital mode:For features that are available in both conventional Analog and Digital modes, no icon is shown.For features that are available in a conventional multi-site mode, see IP Site Connect on page 13 for more information.Selected features are also available on the single-site trunking mode, Capacity Plus. See Capacity Plus on page 14 for more information.Selected features are also available in the multi-site trunking mode, Linked Capacity Plus. See Linked Capacity Plus on page 15 for more information.What Your Dealer/System Administrator Can Tell YouYou can consult your dealer or system administrator about the following:•Is your radio programmed with any preset conventional channels?•Which buttons have been programmed to access other features? •What optional accessories may suit your needs?•What are the best radio usage practices for effective communication?•What maintenance procedures will help promote longer radio life?Indicates a conventional Analog Mode-Only feature.Indicates a conventional Digital Mode-Only feature.
Preparing Your Radio for UseEnglish2Preparing Your Radio for UseAssemble your radio by following these steps:Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2Attaching the Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . page 3Attaching the Antenna. . . . . . . . . . . . . . . . . . . . . . . . . . page 3Attaching the Belt Clip. . . . . . . . . . . . . . . . . . . . . . . . . . page 4Attaching the Universal Connector Cover (Dust Cover) . . . . . . . . . . . . . . . . . . . . . . . . . . page 4Powering Up the Radio . . . . . . . . . . . . . . . . . . . . . . . . . page 5Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . page 5Charging the BatteryFor best performance, your radio is powered by a Motorola-approved Lithium-Ion (Li-lon) battery. To avoid damage and comply with warranty terms, charge the battery using a Motorola charger exactly as described in the charger user guide. If battery is attached to your radio, ensure that your radio remains powered off while charging.Charge a new battery 14 to 16 hours before initial use for best performance.IMPORTANT:ALWAYS charge your IMPRES battery with an IMPRES charger for optimized battery life and valuable battery data. IMPRES batteries charged exclusively with IMPRES chargers receive a 6-month capacity warranty extension over the standard Motorola Premium battery warranty duration.Charge your battery only in non-hazardous areas. After battery is charged, allow your radio to rest for at least 3 minutes. See Batteries on page 114 for available batteries.
Preparing Your Radio for UseEnglish3Attaching the BatteryAlign the battery with the rails on the back of the radio. Press the battery firmly, and slide upward until the latch snaps into place. Slide battery latch into lock position.To remove the battery, turn the radio off. Move the battery latch into unlock position and hold, and slide the battery down and off the rails.Attaching the AntennaWith the radio turned off, set the antenna in its receptacle and turn clockwise.To remove the antenna, turn the antenna counterclockwise. Do not replace batttery in combustible gas and dust environments. Replace battery only in non-hazardous areas. See Batteries on page 114 for available batteries. To LockTo UnlockBattery LatchIf antenna needs to be replaced, ensure that only MOTOTRBO antennas are used. Neglecting this will damage your radio. See Antennas on page 114 for a list of available antennas.
Preparing Your Radio for UseEnglish4Attaching the Belt ClipAlign the grooves on the clip with those on the battery and press downward until you hear a click.To remove the clip, press the belt clip tab away from the battery. Using a key may be helpful. Then slide the clip upward and away from the radio.Attaching the Universal Connector Cover (Dust Cover)The universal connector is located on the antenna side of the radio. It is used to connect MOTOTRBO accessories to the radio.Insert the hooked end of the cover into the slots above the universal connector. Press downward on the cover to seat the lower tab properly into the RF connector. Turn the thumbscrew clockwise to secure the connector cover to the radio.To remove the universal connector cover, press down on the cover and turn the thumbscrew counterclockwise.Replace the dust cover when the universal connector is not in use.Dust Cover
Preparing Your Radio for UseEnglish5Powering Up the RadioRotate the On/Off/Volume Control Knob clockwise until you hear a click. You see MOTOTRBO (TM) on the radio’s display momentarily, followed by a welcome message or welcome image.The LED lights up solid green and the Home screen lights up if the backlight setting is set to turn on automatically.NOTE: The Home screen does not light up during a power up if the LED indicator is disabled (see Turning the LED Indicator On or Off on page 101).A brief tone sounds, indicating that the power up test is successful.NOTE: There is no power up tone if the radio tones/alerts function is disabled (see Turning the Radio Tones/Alerts On or Off on page 95).If your radio does not power up, check your battery. Make sure that it is charged and properly attached. If your radio still does not power up, contact your dealer.To turn off the radio, rotate this knob counterclockwise until you hear a click. You see a brief Powering Down on the radio’s display.Adjusting the VolumeTo increase the volume, turn the On/Off/Volume Control Knob clockwise.To decrease the volume, turn this knob counterclockwise.NOTE: Your radio can be programmed to have a minimum volume offset where the volume level cannot be turned past the programmed minimum volume. Check with your dealer or system administrator for more information.LEDOn/Off/Volume Control KnobOn/Off/Volume Control Knob
Identifying Radio ControlsEnglish6Identifying Radio ControlsTake a moment to review the following:Radio Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 6Programmable Buttons . . . . . . . . . . . . . . . . . . . . . . . . . page 7Using the 4-Way Navigation Button . . . . . . . . . . . . . . page 10Accessing the Programmed Functions . . . . . . . . . . . . page 10Using the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 11Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . . . . . page 12Switching Between Conventional Analog and Digital Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 13IP Site Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 13Capacity Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 14Linked Capacity Plus. . . . . . . . . . . . . . . . . . . . . . . . . . page 15Radio ControlsChannel Selector Knob* On/Off/Volume Control KnobLED Indicator14315171087652111184161319912123
Identifying Radio ControlsEnglish7Programmable ButtonsYour dealer can program the programmable buttons as shortcuts to radio functions or preset channels/groups depending on the duration of a button press:•Short press – Pressing and releasing rapidly.•Long press – Pressing and holding for the programmed duration.•Hold down – Keeping the button pressed.NOTE: The programmed duration of a button press is applicable for all assignable radio/utility functions or settings. See Emergency Operation on page 65 for more information on the programmed duration of the Emergency button.Assignable Radio FunctionsContacts – Provides direct access to the contacts list.Call Alert – Provides direct access to the contacts list for you to select a contact to whom a Call Alert can be sent.Call Forwarding – Toggles Call Forwarding on or off. Call Log – Selects the call log list.Voice Announcement for Channel – Plays zone and channel announcement voice messages for the current channel. This function is unavailable when Voice Announcement is disabled.Side Button 1**Push-to-Talk (PTT) ButtonSide Button 2**Side Button 3**Front Button P1**Menu/OK Button4-Way Navigation ButtonKeypadBack/Home ButtonFront Button P2**DisplayMicrophoneSpeakerUniversal Connector for AccessoriesEmergency Button**Antenna* Display radios have a continuous-rotary Channel Selector Knob** These buttons are programmable.45678910111213141516171819
Identifying Radio ControlsEnglish8Emergency – Depending on the programming, initiates or cancels an emergency alarm or call.Intelligent Audio On/Off – Toggles Intelligent Audio on or off. Manual Dial – Depending on the programming, initiates a Private or Phone call by keying in any subscriber ID or phone number.Manual Site Roam*‡ – Starts the manual site search.Mic AGC On/Off – Toggles the internal microphone automatic gain control (AGC) on or off. Monitor – Monitors a selected channel for activity.Notifications – Provides direct access to the Notifications List.Nuisance Channel Delete*‡ – Temporarily removes an unwanted channel, except for the Selected Channel, from the scan list. The Selected Channel refers to the user’s selected zone/channel combination from which scan is initiated.One Touch Access – Directly initiates a predefined Private, Phone or Group Call, a Call Alert or a Quick Text message.Option Board Feature – Toggles option board feature(s) on or off for option board-enabled channels. Permanent Monitor*‡ – Monitors a selected channel for all radio traffic until function is disabled.Phone – Provides direct access to the Phone Contacts list.Privacy – Toggles privacy on or off.Radio Alias and ID – Provides radio alias and ID.Radio Check – Determines if a radio is active in a system.Radio Enable – Allows a target radio to be remotely enabled.Radio Disable – Allows a target radio to be remotely disabled.Remote Monitor – Turns on the microphone of a target radio without it giving any indicators.Repeater/Talkaround*‡ – Toggles between using a repeater and communicating directly with another radio.Scan*‡ – Toggles scan on or off.Site Info* – Displays current Linked Capacity Plus site name and ID. Plays site announcement voice messages for the current site (this function is unavailable when Voice Announcement is disabled).Site Lock On/Off* – Toggles the automatic site roam on or off.Status – Selects the status list menu. * Not applicable in Capacity Plus‡ Not applicable in Linked Capacity Plus
Identifying Radio ControlsEnglish9Telemetry Control – Controls the Output Pin on a local or remote radio.Text Message – Selects the text message menu.Transmit Interrupt Remote Dekey – Stops the transmission of a remote monitored radio without giving any indicators, or an ongoing interruptible call to free the channel.Voice Announcement On/Off – Toggles Voice Announcement on or off. Voice Operating Transmission (VOX) – Toggles VOX on or off.Zone – Allows selection from a list of zones.Assignable Settings or Utility FunctionsAll Tones/Alerts – Toggles all tones and alerts on or off.Backlight On/Off – Toggles display backlight on or off.Backlight Brightness – Adjusts the brightness level.Display Mode – Toggles the day/night display mode on or off.Keypad Lock – Toggles keypad between locked and unlocked.Squelch – Toggles squelch level between tight and normal.* Not applicable in Capacity Plus‡ Not applicable in Linked Capacity Plus
Identifying Radio ControlsEnglish10Using the 4-Way Navigation ButtonYou can use the 4-way navigation button, e, to scroll through options, increase/decrease values, and navigate vertically. You can use the 4-way navigation button, e, as a number, alias, or free form text editor. Accessing the Programmed FunctionsYou can access various radio functions through one of the following ways:•A short or long press of the relevant programmable buttons.OR•Use the 4-way navigation button as follows:1To access the menu, press the c button. Press the appropriate direction of the e to access the menu functions. 2To select a function or enter a sub-menu, press the c button.3To go back one menu level, or to return to the previous screen, press the d button. Long press the d button to return to the Home screen.NOTE: Your radio automatically exits the menu after a period of inactivity and returns to your Home screen.Category ^ or v< or >Menu Vertical Navigation –Lists Vertical Navigation –View Details Vertical Navigation Previous/Next ItemEditor Category ^ or v< or >Number – Left: Delete last digitRight: –Alias – Move cursor one character left/rightFree Form Text Move cursor up/downMove cursor one character left/rightNumeric Values Increase/Decrease – ced
Identifying Radio ControlsEnglish11Using the KeypadYou can use the 3 x 4 alphanumeric keypad to access your radio’s features. You can use the keypad to enter subscriber aliases or IDs, and text messages. Many characters require that you press a key multiple times. The table below shows the number of times a key needs to be pressed to generate the required character.Number of Times Key is PressedKey1 234567891011121311.,?!@&‘%-:*#2ABC23DEF34GHI45JKL56MNO67PQRS78TUV89WXYZ900NOTE: Press to enter “0” and long press to activate the CAPS lock. Another long press to turn off the CAPS lock.** or del NOTE: Press during text entry to delete the character. Press during numeric entry to enter a “*”.## or space NOTE: Press during text entry to insert a space. Press during numeric entry to enter a “#”.Long press to change text entry method.
Identifying Radio ControlsEnglish12Push-To-Talk (PTT) ButtonThe PTT button on the side of the radio serves two basic purposes:•While a call is in progress, the PTT button allows the radio to transmit to other radios in the call.Press and hold down PTT button to talk. Release the PTT button to listen.The microphone is activated when the PTT button is pressed.•While a call is not in progress, the PTT button is used to make a new call (see Making a Radio Call on page 28).If the Talk Permit Tone (see Turning the Talk Permit Tone On or Off on page 96) or the PTT Sidetone is enabled, wait until the short alert tone ends before talking.During a call, if the Channel Free Indication feature is enabled on your radio (programmed by your dealer), you hear a short alert tone the moment the target radio (the radio that is receiving your call) releases the PTT button, indicating the channel is free for you to respond.You will also hear a continuous talk prohibit tone, if your call is interrupted, indicating that you should release the PTT button, for example when the radio receives an Emergency Call.PTT Button
Identifying Radio ControlsEnglish13Switching Between Conventional Analog and Digital ModeEach channel in your radio can be configured as a conventional analog or conventional digital channel. Use the Channel Selector Knob to switch between an analog or a digital channel.When switching from digital to analog mode, certain features are unavailable. Icons for the digital features (such as Messages) reflect this change by appearing ‘grayed out’. Disabled features are hidden in the menu.Your radio also has features available in both analog and digital mode. However, the minor differences in the way each feature works does NOT affect the performance of your radio.NOTE: Your radio also switches between digital and analog modes during a dual mode scan (see Scan on page 48). IP Site Connect This feature allows your radio to extend conventional communication beyond the reach of a single site, by connecting to different available sites which are connected via an Internet Protocol (IP) network.When the radio moves out of range from one site and into the range of another, it connects to the new site's repeater to send or receive calls/data transmissions. Depending on your settings, this is done automatically or manually.If the radio is set to do this automatically, it scans through all available sites when the signal from the current site is weak or when the radio is unable to detect any signal from the current site. It then locks on to the repeater with the strongest Received Signal Strength Indicator (RSSI) value.In a manual site search, the radio searches for the next site in the roam list that is currently in range (but which may not have the strongest signal) and locks on to it.NOTE: Each channel can only have either Scan or Roam enabled, not both at the same time.Channel Selector Knob
Identifying Radio ControlsEnglish14Channels with this feature enabled can be added to a particular roam list. The radio searches the channel(s) in the roam list during the automatic roam operation to locate the best site.A roam list supports a maximum of 16 channels (including the Selected Channel).NOTE: You cannot manually add or delete an entry to the roam list. Check with your dealer or system administrator for more information.Capacity PlusCapacity Plus is a single-site trunking configuration of the MOTOTRBO radio system, which uses a pool of channels to support hundreds of users and up to 254 Groups. This feature allows your radio to efficiently utilize the available number of programmed channels while in Repeater Mode.Icons of features not applicable to Capacity Plus are not available in the menu. You hear a negative indicator tone if you try to access a feature not applicable to Capacity Plus via a programmable button press.Your radio also has features that are available in conventional digital mode, IP Site Connect, Capacity Plus and Linked Capacity Plus. However, the minor differences in the way each feature works does NOT affect the performance of your radio.Check with your dealer or system administrator for more information on this configuration.
Identifying Radio ControlsEnglish15Linked Capacity Plus Linked Capacity Plus is a multi-site multi-channel trunking configuration of the MOTOTRBO radio system, combining the best of both Capacity Plus and IP Site Connect configurations.Linked Capacity Plus allows your radio to extend trunking communication beyond the reach of a single site, by connecting to different available sites which are connected via an Internet Protocol (IP) network. It also provides an increase in capacity by efficiently utilizing the combined available number of programmed channels supported by each of the available sites. When the radio moves out of range from one site and into the range of another, it connects to the new site's repeater to send or receive calls/data transmissions. Depending on your settings, this is done automatically or manually.If the radio is set to do this automatically, it scans through all available sites when the signal from the current site is weak or when the radio is unable to detect any signal from the current site. It then locks on to the repeater with the strongest Received Signal Strength Indicator (RSSI) value.In a manual site search, the radio searches for the next site in the roam list that is currently in range (but which may not have the strongest signal) and locks on to it.Any channel with Linked Capacity Plus enabled can be added to a particular roam list. The radio searches these channels during the automatic roam operation to locate the best site.NOTE: You cannot manually add or delete an entry to the roam list. Check with your dealer or system administrator for more information.Similar to Capacity Plus, icons of features not applicable to Linked Capacity Plus are not available in the menu. You hear a negative indicator tone if you try to access a feature not applicable to Linked Capacity Plus via a programmable button press.Check with your dealer or system administrator for more information on this configuration.
Identifying Status IndicatorsEnglish16Identifying Status IndicatorsYour radio indicates its operational status through the following:Display Icons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 16Call Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 18Advanced Menu Icons. . . . . . . . . . . . . . . . . . . . . . . . . page 18Mini Notice Icons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 19Sent Item Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 19LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 20Audio Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 21Indicator Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 21Display IconsThe 132 x 90 pixels, 256 colors, liquid crystal display (LCD) of your radio shows radio status, text entries, and menu entries.The following are icons that appear on the status bar at the top of the radio’s display. Icons are displayed on the status bar, arranged left-to-right, in order of appearance/usage and are channel specific. Received Signal Strength Indicator (RSSI)The number of bars displayed represents the radio signal strength. Four bars indicate the strongest signal. This icon is only displayed while receiving.BatteryThe number of bars (0 – 4) shown indicates the charge remaining in the battery.Blinks when the battery is low.EmergencyRadio is in Emergency mode.High Volume DataRadio is receiving high volume data and channel is busy.NotificationNotification List has one or more missed events.Scan*‡Scan feature is enabled.
Identifying Status IndicatorsEnglish17Scan – Priority 1*‡Radio detects activity on channel/group designated as Priority 1).Scan – Priority 2*‡Radio detects activity on channel/group designated as Priority 2.Vote ScanVote scan feature is enabled.MonitorSelected channel is being monitored.Talkaround*‡In the absence of a repeater, radio is currently configured for direct radio to radio communication.Site Roaming* The site roaming feature is enabled.Secure The Privacy feature is enabled.Unsecure The Privacy feature is disabled.GPS Available The GPS feature is enabled. The icon stays lit when a position fix is available.* Not applicable in Capacity Plus‡ Not applicable in Linked Capacity PlusGPS Not Available/Out of Range The GPS feature is enabled but is not receiving data from the satellite.Option BoardThe Option Board is enabled.Option Board Non-FunctionThe Option Board is disabled.Over-the-Air Programming Delay Timer Indicates time left before automatic restart of radio.Tones DisableTones are turned off.* Not applicable in Capacity Plus‡ Not applicable in Linked Capacity Plus
Identifying Status IndicatorsEnglish18Call IconsThe following icons appear on the radio’s display during a call. These icons also appear in the Contacts list to indicate ID type.Advanced Menu IconsThe following icons appear beside menu items that offer a choice between two options or as an indication that there is a sub-menu offering two options. Private CallIndicates a Private Call in progress. In the Contacts list, it indicates a subscriber alias (name) or ID (number).Group Call/All CallIndicates a Group Call or All Call in progress. In the Contacts list, it indicates a group alias (name) or ID (number).Phone Call as Private CallIndicates a Phone Call as Private Call in progress. In the Contacts list, it indicates a phone alias (name) or ID (number).Phone Call as Group/All CallIndicates a Phone Call as Group/All Call in progress. In the Contacts list, it indicates a group alias (name) or ID (number).Checkbox (Empty)Indicates the option is not selected.Checkbox (Checked)Indicates the option is selected.Solid Black BoxIndicates the option selected for the menu item with a sub-menu.
Identifying Status IndicatorsEnglish19Mini Notice IconsThe following icons appear momentarily on the radio’s display after an action to perform task is taken. Sent Item Icons The following icons appear in the Sent Items folder.Successful Transmission (Positive) Successful action taken.Failed Transmission (Negative)Failed action taken.Transmission in Progress (Transitional)Transmitting. This dynamic icon is seen before indication for Successful Transmission or Failed Transmission.Sent SuccessfullyThe text message is sent successfully.Send FailedThe text message cannot be sent.In-Progress•The text message to a subscriber alias or ID is pending transmission, followed by waiting for acknowledgement.•The text message to a group alias or ID is pending transmission.OROROR
Identifying Status IndicatorsEnglish20LED IndicatorThe LED indicator shows the operational status of your radio.Blinking red – Radio is transmitting at low battery condition, receiving an emergency transmission, has failed the self-test upon powering up, or has moved out of range if radio is configured with Auto-Range Transponder System. Solid green – Radio is powering up, or transmitting. Blinking green – Radio is receiving a non-privacy-enabled call or data, detecting activity or retrieving Over-the-Air Programming transmissions over the air.Double blinking green – Radio is receiving a privacy-enabled call or data . Solid yellow – Radio is monitoring a conventional channel. Blinking yellow – Radio is scanning for activity or receiving a Call Alert, or all local Linked Capacity Plus channels are busy.Double blinking yellow – Radio is no longer connected to the repeater while in Capacity Plus or Linked Capacity Plus, all Capacity Plus channels or Linked Capacity Plus channels are currently busy, Auto Roaming is enabled, radio is actively searching for a new site. Also indicates radio has yet to respond to a group call alert, or radio is locked.NOTE: While in conventional mode, when the LED blinks green, it indicates the radio detects activity over the air. Due to the nature of the digital protocol, this activity may or may not affect the radio's programmed channel.For Capacity Plus and Linked Capacity Plus, there is no LED indication when the radio is detecting activity over the air.LED Indicator
Identifying Status IndicatorsEnglish21Indicator TonesHigh pitched tone Low pitched tone Audio TonesAlert tones provide you with audible indications of the radio’s status or the radio’s response to data received.Positive Indicator ToneNegative Indicator ToneContinuous Tone A monotone sound. Sounds continuously until termination.Periodic Tone Sounds periodically depending on the duration set by the radio. Tone starts, stops, and repeats itself.Repetitive Tone A single tone that repeats itself until it is terminated by the user.Momentary Tone Sounds only once for a short period of time defined by the radio.
Making and Receiving CallsEnglish22Making and Receiving CallsOnce you understand how your MOTOTRBO Portable is configured, you are ready to use your radio.Use this navigation guide to familiarize yourself with the basic Call features:Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 22Selecting a Radio Channel, Subscriber ID, or Group ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 24Receiving and Responding to a Radio Call. . . . . . . . . page 24Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . . . page 28Stopping a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . . page 38Talkaround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 38Monitoring Features . . . . . . . . . . . . . . . . . . . . . . . . . . page 39Selecting a ZoneA zone is a group of channels. Your radio supports up to 1000 channels and 250 zones, with a maximum of 160 channels per zone.Use the following procedure to select a zone.Procedure:Press the programmed Zone button and proceed to Step 3. ORFollow the procedure below.1c to access the menu.2^ or v to Zone and press c to select. 3The current zone is displayed and indicated by a 9.4^ or v to the required zone and proceed to Step 7.ORKey in the first character of the required zone.5A blinking cursor appears.Use the keypad to type the required zone.Press < to move one space to the left.Press > to move one space to the right.Press * to delete any unwanted characters.Long press # to change text entry method.
Making and Receiving CallsEnglish236The first line of the display shows the characters you keyed in. The next lines of the display show the shortlisted search results.The alias search is case-insensitive. If there are two or more zones with the same name, the radio displays the zone that is listed first in the zone list.7Press c to select.8The display shows <Zone> Selected momentarily and returns to the selected zone screen.Selecting a ChannelTransmissions are sent and received on a channel. Depending on your radio's configuration, each channel may have been programmed differently to support different groups of users or supplied with different features. After selecting the required zone, select the channel you require to transmit or receive on.Procedure:Turn the Channel Selector Knob to select the channel with the active group alias or ID. Channel Selector Knob
Making and Receiving CallsEnglish24Receiving and Responding to a Radio CallOnce the channel, subscriber ID or group ID is displayed, you can proceed to receive and respond to calls.The LED lights up solid green while the radio is transmitting and blinks green when the radio is receiving.NOTE:The LED lights up solid green while the radio is transmitting and double blinks green when the radio is receiving a privacy-enabled call.To unscramble a privacy-enabled call, your radio must have the same Privacy Key, OR the same Key Value and Key ID (programmed by your dealer), as the transmitting radio (the radio you are receiving the call from). See Privacy on page 84 for more information. Receiving and Responding to a Group CallTo receive a call made to a group of users, your radio must be configured as part of that group.Procedure:When you receive a Group Call (while on the Home screen):1The LED blinks green. 2The Group Call icon appears in the top right corner. The first text line shows the caller alias. The second text line displays the group call alias. Your radio unmutes and the incoming call sounds through the radio's speaker.3To respond, hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 4 If the Channel Free Indication feature is enabled, you hear a short alert tone the moment the transmitting radio releases the PTT button, indicating the channel is free for you to respond.Press the PTT button to respond to the call.OR If the Voice Interrupt feature is enabled, press the PTT button to stop the current call from the transmitting radio and free the channel for you to talk/respond.5The LED lights up solid green.6Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone.LED Indicator
Making and Receiving CallsEnglish25OR Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the microphone.7Release the PTT button to listen.8If there is no voice activity for a predetermined period of time, the call ends.See Making a Group Call on page 29 for details on making a Group Call.Receiving and Responding to a Private Call A Private Call is a call from an individual radio to another individual radio.Procedure:When you receive a Private Call:1The LED blinks green.2The Private Call icon appears in the top right corner. The first text line shows the caller alias. Your radio unmutes and the incoming call sounds through the radio's speaker.3To respond, hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.4If the Channel Free Indication feature is enabled, you hear a short alert tone the moment the transmitting radio releases the PTT button, indicating the channel is free for you to respond.Press the PTT button to respond to the call.ORIf the Voice Interrupt feature is enabled, press the PTT button to stop the current call from the transmitting radio and free the channel for you to talk/respond.5The LED lights up solid green.6Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone.7Release the PTT button to listen.8If there is no voice activity for a predetermined period of time, the call ends.9You hear a short tone. The display shows Call Ended.See Making a Private Call on page 30 for details on making a Private Call.Receiving an All CallAn All Call is a call from an individual radio to every radio on the channel. It is used to make important announcements requiring the user’s full attention.Procedure:When you receive an All Call:1A tone sounds and the LED blinks green. 
Making and Receiving CallsEnglish262The Group Call icon appears in the top right corner. The first text line shows the caller alias. The second text line displays All Call. Your radio unmutes and the incoming call sounds through the radio's speaker.3Once the All Call ends, the radio returns to the previous screen before receiving the call. An All Call does not wait for a predetermined period of time before ending. If the Channel Free Indication feature is enabled, you hear a short alert tone the moment the transmitting radio releases the PTT button, indicating the channel is now available for use.You cannot respond to an All Call.See Making an All Call on page 31 for details on making an All Call.NOTE: The radio stops receiving the All Call if you switch to a different channel while receiving the call.During an All Call, you are not able to use any programmed button functions until the call ends.Receiving and Responding to a Selective Call A Selective Call is a call from an individual radio to another individual radio. It is a Private Call on an analog system.Procedure:When you receive a Selective Call:1The LED blinks green.2The Private Call icon appears in the top right corner. The first text line shows the caller alias or Selective Call or Alert with Call. Your radio unmutes and the incoming call sounds through the radio's speaker.3To respond, hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.4If the Channel Free Indication feature is enabled, you hear a short alert tone the moment the transmitting radio releases the PTT button, indicating the channel is free for you to respond.Press the PTT button to respond to the call.5The LED lights up solid green.6Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone.7Release the PTT button to listen.8If there is no voice activity for a predetermined period of time, the call ends.
Making and Receiving CallsEnglish279You hear a short tone. The display shows Call Ended.See Making a Selective Call on page 31 for details on making a Private Call.Receiving and Responding to a Phone CallPhone Call as a Private Call Procedure:When you receive a Phone Call as a Private Call:1The Phone Call icon appears in the top right corner. The display shows the caller alias or Phone Call.2Press the PTT button to talk and release it to listen. 3Press d to end the call.The display shows Ending Phone Call.4If successful:A tone sounds and the display shows Call Ended. ORIf unsuccessful:Your radio returns to the Phone Call screen. Repeat Step 3 or wait for the telephone user to end the call.If Phone Call capability is not enabled in your radio, the display shows Unavailable and your radio mutes the call. Your radio returns to the previous screen when the call ends.Phone Call as a Group Call Procedure:When you receive a Phone Call as a Group Call:1The Phone Group Call icon appears in the top right corner. The display shows the group alias and Phone Call.2Press the PTT button to talk and release it to listen.3Press d to end the call.The display shows Ending Phone Call.4If successful:A tone sounds and the display shows Call Ended. ORIf unsuccessful:Your radio returns to the Phone Call screen. Repeat Step 3 or wait for the telephone user to end the call.If Phone Call capability is not enabled in your radio, the display shows Unavailable and your radio mutes the call. Your radio returns to the previous screen when the call ends.
Making and Receiving CallsEnglish28Phone Call as an All Call Procedure:When you receive a Phone Call as an All Call:1The Phone Call icon appears in the top right corner. The display shows All Call and Phone Call.2Press the PTT button to talk and release it to listen.3Press d to end the call.The display shows Ending Phone Call.4If successful:A tone sounds and the display shows All Call and Call Ended. ORIf unsuccessful:Your radio returns to the Phone Call screen. Repeat Step 3 to end the call.If Phone Call capability is not enabled in your radio, the display shows Unavailable and your radio mutes the call. Your radio returns to the previous screen when the call ends.NOTE: When you receive a Phone Call as an All Call, you can respond to the call or end the call, only if an All Call type is assigned to the channel.Making a Radio CallAfter selecting your channel, you can select a subscriber alias or ID, or group alias or ID by using:•The Channel Selector Knob•A programmed One Touch Access button •The programmed number keys – This method is for Group, Private and All Calls only and is used with the keypad (see Making a Group, Private or All Call with the Programmable Number Key on page 33). •A programmable button – This method is for Phone Calls only (see Making a Phone Call with the Programmable Phone Button on page 34). •The Contacts list (see Contacts Settings on page 50)•Manual Dial (via Contacts) – This method is for Private Calls only and is dialed using the keypad (see Making a Private Call from Contacts on page 52, Making a Private Call from Contacts on page 52, and Making a Call with the Programmable Manual Dial Button on page 36). NOTE: Your radio must have the Privacy feature enabled on the channel to send a privacy-enabled transmission. Only target radios with the same Privacy Key OR the same Key Value and Key ID as your radio are able to unscramble the transmission. 
Making and Receiving CallsEnglish29See Privacy on page 84 for more information. The One Touch Access feature allows you to make a Group or Private Call to a predefined ID easily. This feature can be assigned to a short or long programmable button press.You can ONLY have one ID assigned to a One Touch Access button. Your radio can have multiple One Touch Access buttons programmed.Making a Call with the Channel Selector KnobMaking a Group CallTo make a call to a group of users, your radio must be configured as part of that group.Procedure:1Select the channel with the active group alias or ID. See Selecting a Channel on page 23.ORPress the programmed One Touch Access button.2Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.3Press the PTT button to make the call. The LED lights up solid green. The Group Call icon appears in the top right corner. The first text line shows the group call alias. 4Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone.OR Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the microphone.5Release the PTT button to listen.When the target radio responds, the LED blinks green. You see the Group Call icon, the group alias or ID, and transmitting radio alias or ID on your display.6 If the Channel Free Indication feature is enabled, you hear a short alert tone the moment the target radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond.ORIf there is no voice activity for a predetermined period of time, the call ends.7Radio returns to the screen you were on prior to initiating the call.You can also make a Group Call via Contacts (see Making a Group Call from Contacts on page 51).
Making and Receiving CallsEnglish30Making a Private Call While you can receive and/or respond to a Private Call initiated by an authorized individual radio, your radio must be programmed for you to initiate a Private Call.There are two types of Private Calls. The first type, where a radio presence check is performed prior to setting up the call, while the other sets up the call immediately. Only one of these call types can be programmed to your radio by your dealer.You hear a negative indicator tone, when you make a Private Call via the Contacts list, Call Log, One Touch Access button, the programmed number keys, or the Channel Selector Knob, if this feature is not enabled.Use the Text Message or Call Alert features to contact an individual radio. See Text Message Features on page 72 or Call Alert Operation on page 63 for more information.Procedure:1Select the channel with the active subscriber alias or ID. See Selecting a Channel on page 23.ORPress the programmed One Touch Access button.2Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.3Press the PTT button to make the call. The LED lights up solid green. The Private Call icon appears in the top right corner. The first text line shows the subscriber alias. The second text line displays the call status. 4Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone. 5Release the PTT button to listen. When the target radio responds, the LED blinks green.6If the Channel Free Indication feature is enabled, you hear a short alert tone the moment the target radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond.ORIf there is no voice activity for a predetermined period of time, the call ends.7You hear a short tone. The display shows Call Ended.You can also make a Private Call via Contacts (see Making a Private Call from Contacts on page 52) or perform a quick alphanumeric search for the required alias via a keypad entry (see Making a Call by Alias Search on page 55).
Making and Receiving CallsEnglish31NOTE: If you release the PTT button while the radio is setting up the call, it exits without any indication and returns to the previous screen.Your radio may be programmed to perform a radio presence check prior to setting up the Private Call. If the target radio is not available, you hear a short tone and see negative mini notice on the display.The radio returns to the menu prior to initiating the radio presence check.Making an All CallThis feature allows you to transmit to all users on the channel. Your radio must be programmed to allow you to use this feature.Procedure:1Select the channel with the active All Call group alias or ID. See Selecting a Channel on page 23.2Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.3Press the PTT button to make the call. The LED lights up solid green. The Group Call icon appears in the top right corner. The first text line shows All Call. 4Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone.OR Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the microphone.Users on the channel cannot respond to an All Call.Making a Selective Call Just like a Private Call, while you can receive and/or respond to a Selective Call initiated by an authorized individual radio, your radio must be programmed for you to initiate a Selective Call.Procedure:1Select the channel with the active subscriber alias or ID. See Selecting a Channel on page 23.2Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.3Press the PTT button to make the call. The LED lights up solid green. The Private Call icon appears in the top right corner. The first text line shows the subscriber alias. The second text line displays the call status. 4Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone. ORWait for the PTT Sidetone to finish (if enabled) and speak clearly into the microphone.
Making and Receiving CallsEnglish325Release the PTT button to listen. When the target radio responds, the LED blinks green.6If the Channel Free Indication feature is enabled, you hear a short alert tone the moment the target radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond.ORIf there is no voice activity for a predetermined period of time, the call ends.7You hear a short tone. The display shows Call Ended.Making a Phone Call with the One Touch Access ButtonProcedure:1Press the programmed One Touch Access button to make a Phone Call to the predefined alias or ID.If the entry for the One Touch Access button is empty, a negative indicator tone sounds.If the access code was not preconfigured in the Contacts list, the display shows Access Code:. Enter the access code and press c to proceed.2The LED lights up solid green. The Phone Call icon appears in the top right corner. The first text line shows the subscriber alias. The second text line displays the call status. 3If successful:The DTMF tone sounds. You hear the dialing tone of the telephone user. The first text line shows the subscriber alias. The Phone Call icon remains in the top right corner. ORIf unsuccessful:A tone sounds and the display shows Phone Call Failed. Your radio returns to the Access Code input screen.If the access code was preconfigured in the Contacts list, the radio returns to the screen you were on prior to initiating the call.4Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.5Press the PTT button to talk and release it to listen. To enter extra digits, if requested by the Phone Call:Enter the extra digits using the keypad and press c to proceed. The DTMF tone sounds and the radio returns to the previous screen.6Press d to end the call.If de-access code was not preconfigured in the Contacts list, the display shows De-Access Code:. Enter the de-access code and press c to proceed. The radio returns to the previous screen.ORPress One Touch Access button. The DTMF tone sounds. If the entry for the One Touch Access button is empty, a negative indicator tone sounds.
Making and Receiving CallsEnglish337The DTMF tone sounds and the display shows Ending Phone Call.8If successful:A tone sounds and the display shows Call Ended. ORIf unsuccessful:Your radio returns to the Phone Call screen. Repeat Steps 6 and 7 or wait for the telephone user to end the call.When the telephone user ends the call, a tone sounds and the display shows Call Ended.If the call ends while you are entering the extra digits requested by the Phone Call, your radio returns to the screen you were on prior to initiating the call.9During channel access, press d to dismiss the call attempt and a tone sounds.During the call, when you press One Touch Access button with the deaccess code preconfigured or enter the deaccess code as the input for extra digits, your radio attempts to end the call.The access or deaccess code cannot be more than 10 characters.Making a Group, Private or All Call with the Programmable Number Key The Programmable Number Key feature allows you to make a Group, Private or All Call to a predefined alias or ID easily. This feature can be assigned to all the available number keys on a keypad.You can ONLY have one alias or ID assigned to a number key, but you can have more than one number key associated to an alias or ID.Procedure:When you are on the Home screen:1Long press the programmed number key to make a Group, Private or All Call to the predefined alias or ID.If the number key is not associated to an entry, a negative indicator tone sounds.2Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.3Press the PTT button to make the call. The LED lights up solid green. The Group/Private Call icon appears in the top right corner. The first text line shows the caller alias. The second text line displays either the call status for a Private Call or All Call for All Call. 
Making and Receiving CallsEnglish344Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone.OR For Group Call only: Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the microphone.5Release the PTT button to listen. When the target radio responds, the LED blinks green.6If the Channel Free Indication feature is enabled, you hear a short alert tone the moment the target radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond.ORIf there is no voice activity for a predetermined period of time, the call ends.7Radio returns to the screen you were on prior to initiating the call.For a Private Call, you hear a short tone when the call ends.See Assigning an Entry to a Programmable Number Key on page 56 for details on assigning an entry to a number key on the keypad.Making a Phone Call with the Programmable Phone ButtonProcedure:1Press the programmed Phone button to enter into the Phone Entry list.2^ or v to the required subscriber alias or ID, and press c to select.If the access code was not preconfigured in the Contacts list, the display shows Access Code:. Enter the access code and press c to proceed.3The LED lights up solid green. The Phone Call icon appears in the top right corner. The first text line shows the subscriber alias. The second text line displays the call status.4If successful:The DTMF tone sounds. You hear the dialing tone of the telephone user. The first text line shows the subscriber alias. The Phone Call icon remains in the top right corner. ORIf unsuccessful:A tone sounds and the display shows Phone Call Failed. Your radio returns to the Access Code input screen.If the access code was preconfigured in the Contacts list, the radio returns to the screen you were on prior to initiating the call.
Making and Receiving CallsEnglish355Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.6Press the PTT button to talk and release it to listen. To enter extra digits, if requested by the Phone Call:Enter the extra digits using the keypad and press c to proceed. The DTMF tone sounds and the radio returns to the previous screen.7Press d to end the call.If de-access code was not preconfigured in the Contacts list, the display shows De-Access Code:. Enter the de-access code and press c to proceed. The radio returns to the previous screen.ORPress One Touch Access button. The DTMF tone sounds. If the entry for the One Touch Access button is empty, a negative indicator tone sounds.8The DTMF tone sounds and the display shows Ending Phone Call.9If successful:A tone sounds and the display shows Call Ended. ORIf unsuccessful:Your radio returns to the Phone Call screen. Repeat Steps 6 and 7 or wait for the telephone user to end the call.When you press PTT button while in the Phone Contacts screen, a tone sounds and the display shows Press OK to Place Call.When the telephone user ends the call, a tone sounds and the display shows Call Ended.If the call ends while you are entering the extra digits requested by the Phone Call, your radio returns to the screen you were on prior to initiating the call.During channel access, press d to dismiss the call attempt and a tone sounds.During the call, when you press One Touch Access button with the deaccess code preconfigured or enter the deaccess code as the input for extra digits, your radio attempts to end the call.The access or de-access code cannot be more than 10 characters.
Making and Receiving CallsEnglish36Making a Call with the Programmable Manual Dial Button Making a Private CallProcedure:1Press the programmed Manual Dial button to enter into the Manual Dial screen.2^ or v to Radio Contact and press c to select.3The display shows Number:. Use the keypad to enter a subscriber alias.4Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.5Press the PTT button to make the call. The LED lights up solid green. The Private Call icon appears in the top right corner. The first text line shows the subscriber alias. The second text line displays the call status. 6Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone. 7Release the PTT button to listen. When the target radio responds, the LED blinks green.8If the Channel Free Indication feature is enabled, you hear a short alert tone the moment the target radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond.ORIf there is no voice activity for a predetermined period of time, the call ends.9You hear a short tone. The display shows Call Ended.Making a Phone CallProcedure:1Press the programmed Manual Dial button to enter into the Manual Dial screen.2^ or v to Phone Contact and press c to select.3The display shows Number:. Use the keypad to enter a subscriber alias.If the access code was not preconfigured in the Contacts list, the display shows Access Code:. Enter the access code and press c to proceed.4The LED lights up solid green. The Phone Call icon appears in the top right corner. The first text line shows the subscriber alias. The second text line displays the call status.
Making and Receiving CallsEnglish375If successful:The DTMF tone sounds. You hear the dialing tone of the telephone user. The first text line shows the subscriber alias. The Phone Call icon remains in the top right corner. ORIf unsuccessful:A tone sounds and the display shows Phone Call Failed. Your radio returns to the Access Code input screen.If the access code was preconfigured in the Contacts list, the radio returns to the screen you were on prior to initiating the call.6Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.7Press the PTT button to talk and release it to listen. To enter extra digits, if requested by the Phone Call:Enter the extra digits using the keypad and press c to proceed. The DTMF tone sounds and the radio returns to the previous screen.8Press d to end the call.If de-access code was not preconfigured in the Contacts list, the display shows De-Access Code:. Enter the de-access code and press c to proceed. The radio returns to the previous screen.ORPress One Touch Access button. The DTMF tone sounds. If the entry for the One Touch Access button is empty, a negative indicator tone sounds.9The DTMF tone sounds and the display shows Ending Phone Call.10 If successful:A tone sounds and the display shows Call Ended. ORIf unsuccessful:Your radio returns to the Phone Call screen. Repeat Step 8 or wait for the telephone user to end the call.When you press PTT button while in the Phone Contacts screen, a tone sounds and the display shows Press OK to Place Call.When the telephone user ends the call, a tone sounds and the display shows Call Ended.If the call ends while you are entering the extra digits requested by the Phone Call, your radio returns to the screen you were on prior to initiating the call.During channel access, press d to dismiss the call attempt and a tone sounds.During the call, when you press One Touch Access button with the deaccess code preconfigured or enter the deaccess code as the input for extra digits, your radio attempts to end the call.The access or de-access code cannot be more than 10 characters.
Making and Receiving CallsEnglish38Stopping a Radio Call This feature allows you to stop an ongoing Group or Private Call to free the channel for transmission. For example, when a radio experiences a “stuck microphone” condition where the PTT button is inadvertently pressed by the user.Your radio must be programmed to allow you to use this feature.Procedure:While on the required channel:1Press the programmed Transmit Interrupt Remote Dekey button.2The display shows Remote Dekey.3Wait for acknowledgment.4The radio sounds a positive indicator tone and the display shows Remote Dekey Success, indicating that the channel is now free.ORThe radio sounds a negative indicator tone and the display shows Remote Dekey Failed.On the interrupted radio, the display shows Call Interrupted and your radio sounds a negative indicator tone until you release the PTT button, if it is transmitting an interruptible call that is stopped via this feature.TalkaroundYou can continue to communicate when your repeater is not operating, or when your radio is out of the repeater’s range but within talking range of other radios. This is called “talkaround”.NOTE: This feature is not applicable in Capacity Plus and Linked Capacity Plus.Procedure:Press the programmed Repeater/Talkaround button to toggle between talkaround and repeater modes.ORFollow the procedure below.1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Talkaround.5Press c to enable Talkaround. The display shows 9 beside Enabled.ORPress c to disable Talkaround. The 9 disappears from beside Enabled.
Making and Receiving CallsEnglish396The screen automatically returns to the previous menu.The Talkaround setting is retained even after powering down.NOTE: At Step 4, you can also use < or > to change the selected option.Monitoring FeaturesMonitoring a ChannelUse the Monitor feature to make sure a channel is clear before transmitting.NOTE: This feature is not applicable in Capacity Plus and Linked Capacity Plus.Procedure:1Press and hold the programmed Monitor button and listen for activity.2The monitor icon appears on the status bar and the LED lights up solid yellow.3You hear radio activity or total silence, depending on how your radio is programmed.4When you hear “white noise” (that is, the channel is free), press the PTT button to talk and release it to listen.Permanent MonitorUse the Permanent Monitor feature to continuously monitor a selected channel for activity. NOTE: This feature is not applicable in Capacity Plus and Linked Capacity Plus.Procedure:1Press the programmed Permanent Monitor button.2Radio sounds an alert tone, the LED lights up solid yellow, and the display shows Permanent Monitor On. The monitor icon appears on the status bar.3Press the programmed Permanent Monitor button to exit Permanent Monitor mode.4Radio sounds an alert tone, the LED turns off, and display shows Permanent Monitor Off.
Advanced FeaturesEnglish40Advanced FeaturesUse this navigation guide to learn more about advanced features available with your radio:Radio Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 41Remote Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 42Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 44Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 48Vote Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 50Contacts Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 50Call Indicator Settings . . . . . . . . . . . . . . . . . . . . . . . . . page 58Call Log Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 62Call Alert Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . page 63Emergency Operation . . . . . . . . . . . . . . . . . . . . . . . . . page 65Man Down. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 71Text Message Features. . . . . . . . . . . . . . . . . . . . . . . . page 72Analog Message Encode . . . . . . . . . . . . . . . . . . . . . . page 83Analog Status Update . . . . . . . . . . . . . . . . . . . . . . . . . page 84Privacy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 84Dual Tone Multi Frequency (DTMF) . . . . . . . . . . . . . . page 85Multi-Site Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . page 86Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 88Lone Worker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 90Password Lock Features. . . . . . . . . . . . . . . . . . . . . . . page 91Notification List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 93Auto-Range Transponder System (ARTS) . . . . . . . . . page 94Over-the-Air Programming (OTAP) . . . . . . . . . . . . . . . page 94Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 95Front Panel Configuration (FPC) . . . . . . . . . . . . . . . . page 113
Advanced FeaturesEnglish41Radio Check If enabled, this feature allows you to determine if another radio is active in a system without disturbing the user of that radio. No audible or visual notification is shown on the target radio.This feature is only applicable for subscriber aliases or IDs.Sending a Radio CheckProcedure: Use the programmed Radio Check button.1Press the programmed Radio Check button.2^ or v to the required subscriber alias or ID and press c to select.3The display shows transitional mini notice, indicating the request is in progress. The LED lights up solid green. 4Wait for acknowledgement.5If successful, a positive indicator tone sounds and the display shows positive mini notice. ORIf unsuccessful, a negative indicator tone sounds and the display shows negative mini notice.6Radio returns to the subscriber alias or ID screen.ORProcedure: Use the menu.1c to access the menu.2^ or v to Contacts and press c to select.3^ or v to the required subscriber alias or ID and press c to select.OR^ or v to Manual Dial and press c to select. ^ or v to Radio Number and press c to select.If there was previously dialed ID, the ID appears along with a blinking cursor. Use the keypad to edit the ID. Press c to select.OR^ or v to Manual Dial and press c to select.^ or v to Radio Number and press c to select.The first line of the display shows Radio Number:. The second line of the display shows a blinking cursor. Key in the subscriber alias or ID and press c.4^ or v to Radio Check and press c to select.5The display shows transitional mini notice, indicating the request is in progress. The LED lights up solid green. 6Wait for acknowledgement.
Advanced FeaturesEnglish427If successful, a positive indicator tone sounds and the display shows positive mini notice. ORIf unsuccessful, a negative indicator tone sounds and the display shows negative mini notice.8Radio returns to the subscriber alias or ID screen.If the d button is pressed when the radio is waiting for acknowledgement, a tone sounds, and the radio terminates all retries and exits Radio Check mode.Remote Monitor Use the Remote Monitor feature to turn on the microphone of a target radio (subscriber alias or IDs only). No audible or visual indication is given to the target radio. You can use this feature to monitor, remotely, any audible activity surrounding the target radio.Your radio must be programmed to allow you to use this feature.Initiating Remote MonitorProcedure: Use the programmed Remote Monitor button.1Press the programmed Remote Monitor button.2^ or v to the required subscriber alias or ID and press c to select.3The display shows transitional mini notice, indicating the request is in progress. The LED lights up solid green.4Wait for acknowledgment.5If successful, a positive indicator tone sounds and the display shows positive mini notice. Your radio starts playing audio from the monitored radio for a programmed duration and display shows Rem. Monitor. Once the timer expires, the radio sounds an alert tone and the LED turns off.ORIf unsuccessful, a negative indicator tone sounds and the display shows negative mini notice.ORProcedure: Use the menu.1c to access the menu.2^ or v to Contacts and press c to select.3^ or v to the required subscriber alias or ID and press c to select.OR^ or v to Manual Dial and press c to select. 
Advanced FeaturesEnglish43^ or v to Radio Number and press c to select.If there was previously dialed ID, the ID appears along with a blinking cursor. Use the keypad to edit the ID. Press c to select.OR^ or v to Manual Dial and press c to select.^ or v to Radio Number and press c to select.The first line of the display shows Radio Number:. The second line of the display shows a blinking cursor. Key in the subscriber alias or ID and press c to select.4^ or v to Remote Mon. and press c to select.5The display shows transitional mini notice, indicating the request is in progress. The LED lights up solid green.6Wait for acknowledgment.7If successful, a positive indicator tone sounds and the display shows positive mini notice. Your radio starts playing audio from the monitored radio for a programmed duration and display shows Rem. Monitor. Once the timer expires, the radio sounds an alert tone and the LED turns off.ORIf unsuccessful, the radio sounds a negative indicator tone the display shows negative mini notice.Stopping Remote MonitorRemote Monitor automatically stops after a programmed duration or when there is any user operation on the target radio.Procedure: 1Press the programmed Transmit Interrupt Remote Dekey button.2The display shows transitional mini notice, indicating the request is in progress. The LED lights up solid green. 3Wait for acknowledgment.4If successful, a positive indicator tone sounds and the display shows positive mini notice.ORIf unsuccessful, a negative indicator tone sounds and the display shows negative mini notice.
Advanced FeaturesEnglish44Scan ListsScan lists are created and assigned to individual channels/groups. Your radio scans for voice activity by cycling through the channel/group sequence specified in the scan list for the current channel/group. Your radio can support up to 250 scan lists, with a maximum of 16 members in a list. Each scan list supports a mixture of both analog and digital entries.You can add, delete, or prioritize channels by editing a scan list.You can attach a new scan list to your radio via Front Panel Programming. NOTE: This feature is not applicable in Capacity Plus and Linked Capacity Plus.Viewing an Entry in the Scan ListProcedure:1c to access the menu.2^ or v to Scan and press c to select.3^ or v to Scan List and press c to select.4Use ^ or v to view each member on the list.The priority icon appears left of the member’s alias, if set, to indicate whether the member is on a Priority 1 or Priority 2 channel list. You cannot have multiple Priority 1 or Priority 2 channels in a scan list.There is no priority icon if priority is set to None.
Advanced FeaturesEnglish45Viewing an Entry in the Scan List by Alias SearchProcedure:1c to access the menu.2^ or v to Scan and press c to select.3^ or v to Scan List and press c to select.4Key in the first character of the required alias.5A blinking cursor appears.Use the keypad to type the required alias.Press < to move one space to the left.Press > to move one space to the right.Press * to delete any unwanted characters.Long press # to change text entry method.6The first line of the display shows the characters you keyed in. The next lines of the display show the shortlisted search results.The alias search is case-insensitive. If there are two or more entries with the same name, the radio displays the entry that is listed first in the scan list.Editing the Scan ListAdding a New Entry to the Scan ListProcedure:1c to access the menu.2^ or v to Scan and press c to select.3^ or v to Scan List and press c to select.4^ or v to Add Member and press c to select.5^ or v to the required alias or ID and proceed to Step 8.ORKey in the first character of the required alias.6A blinking cursor appears.Use the keypad to type the required alias.Press < to move one space to the left.Press > to move one space to the right.Press * to delete any unwanted characters.Long press # to change text entry method.
Advanced FeaturesEnglish467The first line of the display shows the characters you keyed in. The next lines of the display show the shortlisted search results.The alias search is case-insensitive. If there are two or more aliases with the same name, the radio displays the alias that is listed first in the list.8Press c to select.9^ or v to the required priority level and press c to select.10 The display shows positive mini notice, followed immediately by Add Another?.11 ^ or v to Yes and press c to select, to add another entry, and repeat Steps 5 to 9.OR^ or v to No and press c to select to save the current list.Deleting an Entry from the Scan ListProcedure:1c to access the menu.2^ or v to Scan and press c to select.3^ or v to Scan List and press c to select.4^ or v to the required alias or ID and proceed to Step 7.ORKey in the first character of the required alias.5A blinking cursor appears.Use the keypad to type the required alias.Press < to move one space to the left.Press > to move one space to the right.Press * to delete any unwanted characters.Long press # to change text entry method.6The first line of the display shows the characters you keyed in. The next lines of the display show the shortlisted search results.The alias search is case-insensitive. If there are two or more entries with the same name, the radio displays the entry that is listed first in the scan list.7Press c to select.
Advanced FeaturesEnglish478^ or v to Delete and press c to select.9At Delete Entry?, ^ or v to Yes and press c to select, to delete the entry. The display shows positive mini notice. OR^ or v to No and press c to select to return to the previous screen.10 Repeat Steps 4 to 9 to delete other entries. After deleting all required aliases or IDs, long press d to return to the Home screen.Setting and Editing Priority for an Entry in the Scan ListProcedure:1c to access the menu.2^ or v to Scan and press c to select.3^ or v to Scan List and press c to select.4^ or v to the required alias or ID and proceed to Step 7.ORKey in the first character of the required alias.5A blinking cursor appears.Use the keypad to type the required alias.Press < to move one space to the left.Press > to move one space to the right.Press * to delete any unwanted characters.Long press # to change text entry method.6The first line of the display shows the characters you keyed in. The next lines of the display show the shortlisted search results.The alias search is case-insensitive. If there are two or more entries with the same name, the radio displays the entry that is listed first in the scan list.7Press c to select.8^ or v to Edit Priority and press c to select.9^ or v to the required priority level and press c to select.10 The display shows positive mini notice before returning to the previous screen.11 The priority icon appears left of the member’s name.There is no priority icon if priority is set to None.
Advanced FeaturesEnglish48ScanWhen you start a scan, your radio cycles through the programmed scan list for the current channel looking for voice activity.The LED blinks yellow and the scan icon appears on the status bar.During a dual mode scan, if you are on a digital channel, and your radio locks onto an analog channel, it automatically switches from digital mode to analog mode for the duration of the call. This is also true for the reverse.There are two ways of initiating scan: •Main Channel Scan (Manual): Your radio scans all the channels/groups in your scan list. On entering scan, your radio may – depending on the settings – automatically start on the last scanned “active” channel/group or on the channel where scan was initiated.•Auto Scan (Automatic): Your radio automatically starts scanning when you select a channel/group that has Auto Scan enabled.NOTE: This feature is not applicable in Capacity Plus and Linked Capacity Plus.Starting and Stopping ScanProcedure: Press the programmed Scan button to start or stop Scan. OR Follow the procedure below.1Use the Channel Selector Knob to select a channel programmed with a scan list.2c to access the menu.3^ or v to Scan and press c to select.4^ or v to Scan State and press c to select.5^ or v to required scan state and press c to select.6The display shows Scan On when scan is enabled. The LED blinks yellow and the scan icon appears. ORThe display shows Scan Off if scan is disabled. The LED turns off and the scan icon disappears. While scanning, the radio can only accept data (e.g. text message, location, telemetry, or PC data) if received on its Selected Channel.
Advanced FeaturesEnglish49Responding to a Transmission During a ScanDuring scanning, your radio stops on a channel/group where activity is detected. The radio stays on that channel for a programmed time period known as “hang time”. Procedure: 1Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. If the Channel Free Indication feature is enabled, you hear a short alert tone the moment the transmitting radio releases the PTT button, indicating the channel is free for you to respond.2Press the PTT button during hang time. The LED lights up solid green.3Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone.OR Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the microphone.4Release the PTT button to listen.5If you do not respond within the hang time, the radio returns to scanning other channels/groups.Deleting a Nuisance ChannelIf a channel continually generates unwanted calls or noise (termed a “nuisance” channel), you can temporarily remove the unwanted channel from the scan list.This capability does not apply to the channel designated as the Selected Channel.Procedure:1When your radio “locks on to” an unwanted or nuisance channel, press the programmed Nuisance Channel Delete button until you hear a tone.2Release the Nuisance Channel Delete button. The nuisance channel is deleted.Deleting a “nuisance” channel is only possible through the programmed Nuisance Channel Delete button. This feature is not accessible through the menu.Restoring a Nuisance ChannelProcedure: To restore the deleted nuisance channel, do one of the following:•Turn the radio off and then power it on again, OR•Stop and restart a scan via the programmed Scan button or menu, OR•Change the channel via the Channel Selector Knob. 
Advanced FeaturesEnglish50Vote ScanVote Scan provides you with wide area coverage in areas where there are multiple base stations transmitting identical information on different analog channels.Your radio scans analog channels of multiple base stations and performs a voting process to select the strongest received signal. Once that is established, your radio unmutes to transmissions from that base station. The LED blinks yellow and the vote scan icon appears on the status bar.To respond to a transmission during a Vote Scan, follow the same procedures as Responding to a Transmission During a Scan on page 49.Contacts SettingsContacts provides “address-book” capabilities on your radio. Each entry corresponds to an alias or ID that you use to initiate a call.Each entry, depending on context, associates with one of five types of calls: Group Call, Private Call, All Call, PC Call or Dispatch Call.PC Call and Dispatch Call are data-related. They are only available with the applications. Refer to the data applications documentation for more information.NOTE: If the Privacy feature is enabled on a channel, you can make privacy-enabled Group Call, Private Call, and All Call on that channel. Only target radios with the same Privacy Key OR the same Key Value and Key ID as your radio are able to unscramble the transmission.See Privacy on page 84 for more information. Additionally, Contacts menu allows you to assign each entry to a programmable number key or more on a keypad. If an entry is assigned to a number key, your radio can perform a quick dial on the entry.
Advanced FeaturesEnglish51Your radio supports two Contacts lists, one for Analog contacts and one for Digital contacts, with a maximum of 500 members for each Contacts list.Each entry within Contacts displays the following information:•Call Type•Call Alias•Call IDNOTE: You can add, or edit subscriber IDs for the Digital Contacts list. Deleting subscriber IDs can only be performed by your dealer.For the Analog Contacts list, you can only view the subscriber IDs, edit the subscriber IDs, and initiate a Call Alert. Adding and deleting capabilities can only be performed by your dealer.Making a Group Call from ContactsProcedure:1c to access the menu.2^ or v to Contacts and press c to select.The entries are alphabetically sorted.3^ or v to the required group alias or ID.4Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.5Press the PTT button to make the call. The LED lights up solid green.6Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone.OR Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the microphone.7Release the PTT button to listen. When any user in the group responds, the LED blinks green. You see the Group Call icon, the group ID, and that user’s ID on your display.8 If the Channel Free Indication feature is enabled, you hear a short alert tone the moment the target radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond. OR
Advanced FeaturesEnglish52If there is no voice activity for a programmed period of time, the call ends.Making a Private Call from Contacts Procedure:1c to access the menu.2^ or v to Contacts and press c to select.The entries are alphabetically sorted.3^ or v to the required subscriber alias or ID.OR^ or v to Manual Dial and press c to select.^ or v to Radio Number and press c to select.If there was previously dialed subscriber alias or ID, the alias or ID appears along with a blinking cursor. Use the keypad to edit the ID.OR^ or v to Manual Dial and press c to select. ^ or v to Radio Number and press c to select.The first line of the display shows Radio Number:. The second line of the display shows a blinking cursor. Use the keypad to enter a new subscriber alias or ID.4Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.5Press the PTT button to make the call. The LED lights up solid green. The display shows the destination alias.6Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone.7Release the PTT button to listen. When the target radio responds, the LED blinks green and the display shows the transmitting user's ID.8If the Channel Free Indication feature is enabled, you hear a short alert tone the moment the target radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond.ORIf there is no voice activity for a programmed period of time, the call ends.9You hear a short tone. The display shows Call Ended.
Advanced FeaturesEnglish53Making a Phone Call from Contacts Procedure:1c to access the menu.2^ or v to Contacts and press c to select. The entries are alphabetically sorted.3^ or v to the required subscriber alias or ID.OR^ or v to Manual Dial and press c to select.^ or v to Phone Number and press c to select.The first line of the display shows Phone Number:. The second line of the display shows a blinking cursor. Use the keypad to enter a telephone number.4Press c to select.If the entry selected is empty, a negative indicator tone sounds and the display shows Phone Call Invalid #.5^ or v to Call Phone and press c to select.If the access code was not preconfigured in the Contacts list, the first line of the display shows Access Code:. The second line of the display shows a blinking cursor. Enter the access code and press c to proceed.6The first line of the display shows Calling. The second line of the display shows the subscriber alias or ID, and the Phone Call icon.7If successful:The DTMF tone sounds. You hear the dialing tone of the telephone user. The first line of the display shows the subscriber alias or ID, and the RSSI icon. The second line of the display shows Phone Call and the Phone Call icon.ORIf unsuccessful:A tone sounds and the display shows Phone Call Failed. Your radio returns to the Access Code input screen.If the access code was preconfigured in the Contacts list, the radio returns to the screen you were on prior to initiating the call.8Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.9Press the PTT button to talk and release it to listen. The RSSI icon disappears during transmission.To enter extra digits, if requested by the Phone Call:The first line of the display shows Extra Digits:. The second line of the display shows a blinking cursor. Enter the extra digits using the keypad and press c to proceed. The DTMF tone sounds and the radio returns to the previous screen.ORPress One Touch Access button. The DTMF tone sounds. If the entry for the One Touch Access button is empty, a negative indicator tone sounds.
Advanced FeaturesEnglish5410 Press d to end the call.If deaccess code was not preconfigured in the Contacts list, the first line of the display shows De-Access Code:. The second line of the display shows a blinking cursor. Enter the deaccess code and press c to proceed. The radio returns to the previous screen.11 The DTMF tone sounds and the display shows Ending Phone Call.12 If successful:A tone sounds and the display shows Phone Call Ended. Your radio returns to the Call Phone screen.ORIf unsuccessful:Your radio returns to the Phone Call screen. Repeat Steps 10 and 11 or wait for the telephone user to end the call.When you press PTT button while in the Phone Contacts screen, a negative indicator tone sounds and the display shows Press OK to Place Phone Call.When the telephone user ends the call, a tone sounds and the display shows Phone Call Ended.If the call ends while you are entering the extra digits requested by the Phone Call, your radio returns to the screen you were on prior to initiating the call.During channel access, press d to dismiss the call attempt and a negative indicator tone sounds. Your radio returns to the Call Phone screen.During the call, when you press One Touch Access button with the deaccess code preconfigured or enter the deaccess code as the input for extra digits, your radio attempts to end the call.During channel access and access/deaccess code or extra digits transmission, your radio responds to On/Off/Volume Control Knob and Channel Selector Knob only. A tone sounds for every invalid input.The access or deaccess code cannot be more than 10 characters.
Advanced FeaturesEnglish55Making a Call by Alias Search You can also use alias or alphanumeric search to retrieve the required subscriber alias.This feature is only applicable while in Contacts.Procedure:1c to access the menu.2^ or v to Contacts and press c to select. The entries are alphabetically sorted.3Key in the first character of the required alias.4A blinking cursor appears.Use the keypad to type the required alias.Press < to move one space to the left.Press > to move one space to the right.Press * to delete any unwanted characters.Long press # to change text entry method.5The first line of the display shows the characters you keyed in. The next lines of the display show the shortlisted search results.The alias search is case-insensitive. If there are two or more aliases with the same name, the radio displays the alias that is listed first in the Contacts list.6Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.7Press the PTT button to make the call. The LED lights up solid green. The display shows the destination alias.8Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone.9Release the PTT button to listen. When the target radio responds, the LED blinks green.10 If the Channel Free Indication feature is enabled, you hear a short alert tone the moment the target radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond.ORIf there is no voice activity for a programmed period of time, the call ends.11 You hear a short tone. The display shows Call Ended.
Advanced FeaturesEnglish56NOTE: Press d button or c to exit alias search.If you release the PTT button while the radio is setting up the call, it exits without any indication and returns to the previous screen.Your radio may be programmed to perform a radio presence check prior to setting up the Private Call. If the target radio is not available, you hear a short tone and see negative mini notice on the display.The radio returns to the menu prior to initiating the radio presence check.Assigning an Entry to a Programmable Number Key Procedure:1c to access the menu.2^ or v to Contacts and press c to select. The entries are alphabetically sorted.3^ or v to the required alias or ID and press c to select.4^ or v to Program Key and press c to select.5^ or v to the desired number key and press c to select.ORIf the number key is currently assigned to another entry, the display shows The Key is Already Used and then, the first line of the display shows Overwrite?.^ or v to Yes and press c to select.6The radio sounds a positive indicator tone and the display shows positive mini notice.7The screen automatically returns to the previous menu.NOTE: Each entry can be associated to different number keys. You see a checkmark before each number key that is assigned to an entry. If the checkmark is before Empty, you have not assign a number key to the entry.If a number key is assigned to an entry in a particular mode, this feature is not supported when you long press the number key in another mode.See Making a Group, Private or All Call with the Programmable Number Key on page 33 for details on making a Group, Private or All Call with the programmed number key(s).
Advanced FeaturesEnglish57Removing the Association between Entry and Programmable Number Key Procedure:Long press the programmed number key to the required alias or ID, press c to select, and proceed to Step 4.ORFollow the procedure below.1c to access the menu.2^ or v to Contacts and press c to select. The entries are alphabetically sorted.3^ or v to the required alias or ID and press c to select.4^ or v to Program Key and press c to select.5^ or v to Empty and press c to select.6The first line of the display shows Clear from all keys?.7^ or v to Yes and press c to select.8The radio sounds a positive indicator tone and the display shows positive mini notice.9The screen automatically returns to the previous menu.NOTE: When an entry is deleted, the association between the entry and its programmed number key(s) is removed.Setting Default Contact Procedure:Follow the procedure below.1c to access the menu.2^ or v to Contacts and press c to select.3^ or v to the required alias or ID and press c to select.4^ or v to Set as Default and press c to select.5The radio sounds a positive indicator tone and the display shows positive mini notice.6A 9 appears beside the selected default alias or ID.
Advanced FeaturesEnglish58 Adding a New ContactProcedure:Follow the procedure below.1c to access the menu.2^ or v to Contacts and press c to select.3^ or v to New Contact and press c to select.4^ or v to the required contact type, either Radio Contact or Phone Contact, and press c to select.5Use the keypad to enter the contact number and press c to confirm.6Use the keypad to enter the contact name and press c to confirm.7If adding a Radio Contact, ^ or v to the required ringer type and press c to select. The radio sounds a positive indicator tone and the display shows positive mini notice.Call Indicator Settings Activating or Deactivating Call Ringers for Call Alert You can select, or turn on or off ringing tones for a received Call Alert.Procedure: 1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Tones/Alerts and press c to select.5^ or v to Call Ringers and press c to select.6^ or v to Call Alert and press c to select. The current tone is indicated by a 9.7^ or v to the required tone and press c to select. 9 appears beside selected tone. NOTE: At Step 6, you can also use < or > to change the selected option.
Advanced FeaturesEnglish59Activating or Deactivating Call Ringers for Private Calls You can turn on or off the ringing tones for a received Private Call.Procedure:1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Tones/Alerts and press c to select.5^ or v to Call Ringers and press c to select.6^ or v to Private Call.7Press c to enable Private Call ringing tones. The display shows 9 beside Enabled.ORPress c to disable Private Call ringing tones. The 9 disappears from beside Enabled.NOTE: At Step 6, you can also use < or > to change the selected option.Activating or Deactivating Call Ringers for Selective Call You can select, or turn on or off ringing tones for a received Selective Call.Procedure: 1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Tones/Alerts and press c to select.5^ or v to Call Ringers and press c to select.6^ or v to Selective Call and press c to select. The current tone is indicated by a 9.7^ or v to the required tone and press c to select. 9 appears beside selected tone. NOTE: At Step 6, you can also use < or > to change the selected option. 
Advanced FeaturesEnglish60Activating or Deactivating Call Ringers for Text Message You can select, or turn on or off the ringing tones for a received Text Message.Procedure: 1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Tones/Alerts and press c to select.5^ or v to Call Ringers and press c to select.6^ or v to Messages and press c to select. The current tone is indicated by a 9.7 ^ or v to the required tone and press c to select. 9 appears beside selected tone. NOTE: At Step 6, you can also use < or > to change the selected option.Activating or Deactivating Call Ringers for Telemetry Status with Text You can turn on or off the alert tones for a received Telemetry Status with Text.Procedure: 1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Tones/Alerts and press c to select.5^ or v to Call Ringers and press c to select.6^ or v to Telemetry and press c to select. The current tone is indicated by a 9.7^ or v to the required tone and press c to select. 9 appears beside selected tone. NOTE: At Step 6, you can also use < or > to change the selected option. 
Advanced FeaturesEnglish61Assigning Ring Styles You can program your radio to sound one of ten predefined ringing tones when receiving a Call Alert or a Text Message from a particular contact.Procedure: 1c to access the menu.2^ or v to Contacts and press c to select.The entries are alphabetically sorted.3^ or v to the required alias or ID and press c to select.4^ or v to Edit and press c to select.5Press c until display shows Edit Ringtone menu.6A 9 indicates the current selected tone.7^ or v to the required tone and press c to select. 9 appears beside selected tone. 8The display shows a positive mini notice.The radio sounds out each ring style as you navigate through the list.Escalating Alarm Tone VolumeYou can program your radio to continually alert you when a radio call remains unanswered. This is done by automatically increasing the alarm tone volume over time. This feature is known as Escalert.Procedure:1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Tones/Alerts and press c to select.5^ or v to Escalert.6Press c to enable Escalert. The display shows 9 beside Enabled.ORPress c to disable Escalert. The 9 disappears from beside Enabled.NOTE: At Step 5, you can also use < or > to change the selected option.
Advanced FeaturesEnglish62Call Log Features Your radio keeps track of all recent outgoing, answered, and missed Private Calls. Use the call log feature to view and manage recent calls.You can perform the following tasks in each of your call lists:•Store ID to Contacts•Delete•View DetailsViewing Recent CallsThe lists are Missed, Answered, and Outgoing.Procedure:1c to access the menu.2^ or v to Call Log and press c to select.3^ or v to required list and press c to select.4The display shows the most recent entry at the top of the list.5^ or v to view the list.Press the PTT button to start a Private Call with the current selected alias or ID.Storing an Alias or ID from a Call ListProcedure:1c to access the menu.2^ or v to Call Log and press c to select.3^ or v to the required list and press c to select.4^ or v to the required alias or ID and press c to select.5^ or v to Store and press c to select.6A blinking cursor appears. If needed, key in the alias for that ID and press c.7The display shows positive mini notice.You can also store an ID without an alias.Deleting a Call from a Call ListProcedure:1c to access the menu.2^ or v to Call Log and press c to select.3^ or v to the required list and press c to select.4^ or v to the required alias or ID and press c to select.
Advanced FeaturesEnglish635^ or v to Delete and press c to select.6Press c to select Yes to delete the entry. The display shows positive mini notice.OR^ or v to No to return to the previous screen.When you select a call list and it contains no entries, the display shows List Empty, and sounds a low tone if Keypad Tones are turned on (see Turning Keypad Tones On or Off on page 95).Viewing Details from a Call ListProcedure:1c to access the menu.2^ or v to Call Log and press c to select.3^ or v to the required list and press c to select.4^ or v to the required alias or ID and press c to select.5^ or v to View Details and press c to select. Display shows details. Call Alert OperationCall Alert paging enables you to alert a specific radio user to call you back when they are able to do so.This feature is applicable for subscriber aliases or IDs only and is accessible through the menu via Contacts or manual dial.Receiving and Responding to a Call AlertWhen you receive a Call Alert page, you see the notification list listing a Call Alert with the alias or ID of the calling radio on the display.Procedure:1You hear a repetitive tone. The LED blinks yellow.2Press the PTT button while the display still shows the Call Alert in the Notification List to respond with a Private Call.ORPress d to exit the Notification List. The alert is moved to the Missed Call Log. See Notification List on page 93 for details about the Notification List.See Call Log Features on page 62 for details about the Missed Call List.
Advanced FeaturesEnglish64Making a Call Alert from the Contacts ListProcedure:1c to access the menu.2^ or v to Contacts and press c to select.3^ or v to the required subscriber alias or ID and press c to select.OR^ or v to Manual Dial and press c to select. ^ or v to Radio Number and press c to select.The first line of the display shows Radio Number:. The second line of the display shows a blinking cursor.A blinking cursor appears. Enter the subscriber ID you want to page and press c.4^ or v to Call Alert and press c to select.5The display shows Call Alert and the subscriber alias or ID, indicating that the Call Alert has been sent. 6The LED lights up solid green when your radio is sending the Call Alert.7If the Call Alert acknowledgement is received, the display shows positive mini notice.ORIf the Call Alert acknowledgement is not received, the display shows negative mini notice.Making a Call Alert with the One Touch Access Button Procedure:1Press the programmed One Touch Access button to make a Call Alert to the predefined alias or ID.2The display shows Call Alert and the subscriber alias or ID, indicating that the Call Alert has been sent. 3The LED lights up solid green when your radio is sending the Call Alert.4If the Call Alert acknowledgement is received, the display shows positive mini notice.ORIf the Call Alert acknowledgement is not received, the display shows negative mini notice.
Advanced FeaturesEnglish65Emergency OperationAn Emergency Alarm is used to indicate a critical situation. You are able to initiate an Emergency at any time on any screen display even when there is activity on the current channel.Your dealer can set the duration of a button press for the programmed Emergency button, except for long press, which is similar with all other buttons:•Short press – Between 0.05 seconds and 0.75 seconds•Long press – Between 1.00 second and 3.75 secondsThe Emergency button is assigned with the Emergency On/Off feature. Check with your dealer for the assigned operation of the Emergency button.If short press the Emergency button is assigned to turn on the Emergency mode, then long press the Emergency button is assigned to exit the Emergency mode.If long press the Emergency button is assigned to turn on the Emergency mode, then short press the Emergency button is assigned to exit the Emergency mode.Your radio supports three Emergency Alarms:•Emergency Alarm•Emergency Alarm with Call•Emergency Alarm with Voice to Follow In addition, each alarm has the following types:•Regular – Radio transmits an alarm signal and shows audio and/or visual indicators.•Silent – Radio transmits an alarm signal without any audio or visual indicators. Radio receives calls without any sound through the radio’s speaker, until you press the PTT button to initiate the call.•Silent with Voice – Radio transmits an alarm signal without any audio or visual indicators, but allow incoming calls to sound through the radio’s speaker.Only ONE of the Emergency Alarms above can be assigned to the programmed Emergency button.Receiving an Emergency AlarmProcedure:1The emergency icon appears, a tone sounds, the LED blinks red, and the radio displays the Alarm List if there is more than one alarm listed. The emergency caller aliases are listed. ^ or v to the required alias and press c to view more details. Press c again to view your action options.ORThe emergency icon appears, a tone sounds, the LED blinks red, and the radio displays the emergency caller alias Press c to view more details. Press c again to view your action options.
Advanced FeaturesEnglish662Press d and select Yes to exit the Alarm List. To revisit the Alarm List, press c to access the menu and select Alarm List. Responding to an Emergency AlarmProcedure:When receiving an Emergency Alarm:1In the Alarm List, ^ or v to the required alias. 2Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. If the Channel Free Indication feature is enabled, you hear a short alert tone the moment the transmitting radio releases the PTT button, indicating the channel is now available for use.3Press PTT button to transmit non-emergency voice to the same group that the Emergency Alarm was targeted to. The LED lights up solid green. Your radio remains in the Emergency mode.4Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone.OR Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the microphone.5Release the PTT button to listen. When the emergency initiating radio responds, the LED blinks green. You see the Group Call icon, the group ID, and transmitting radio ID on your display.6 Your radio displays the Alarm List. Emergency voice can only be transmitted by the emergency initiating radio. All other radios (including the emergency receiving radio) transmit non-emergency voice.Sending an Emergency AlarmThis feature allows you to send an Emergency Alarm, a non-voice signal, which triggers an alert indication on a group of radios. Procedure: 1Press the programmed Emergency On button.2The display shows Tx Alarm and the destination alias. The LED lights up solid green and the Emergency icon appears.ORThe display shows Tx Telegram and the destination alias. The LED lights up solid green and the Emergency icon appears.3When an Emergency Alarm acknowledgment is received, the Emergency tone sounds and the LED blinks green. The display shows Alarm Sent.OR
Advanced FeaturesEnglish67If your radio does not receive an Emergency Alarm acknowledgement, and after all retries have been exhausted, a tone sounds and the display shows Alarm Failed.4Radio exits the Emergency Alarm mode and returns to the Home screen.If your radio is set to Silent, it does not display any audio or visual indicators during Emergency mode.Sending an Emergency Alarm with CallThis feature allows you to send an Emergency Alarm to a group of radios. Upon acknowledgement by a radio within the group, the group of radios can communicate over a programmed Emergency channel.Procedure: 1Press the programmed Emergency On button.2The display shows Tx Alarm and the destination alias. The LED lights up solid green and the Emergency icon appears.ORThe display shows Tx Telegram and the destination alias. The LED lights up solid green and the Emergency icon appears.3When an Emergency Alarm acknowledgment is received, the Emergency tone sounds and the LED blinks green. The display shows Alarm Sent.4Your radio enters the emergency call mode when the display shows Emergency and the destination group alias.5Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.6Press PTT button to make the call. The LED lights up solid green and the group icon appears on the display. 7Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone.OR Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the microphone.8Release the PTT button to listen.When you receive a group call, the display shows the caller alias and group alias.9When the channel is free for you to respond, a short alert tone sounds ( if the Channel Free Indication feature is enabled). Press the PTT button to respond.OROnce your call ends, press Emergency Off button to exit the Emergency mode.10 The radio returns to the Home screen.
Advanced FeaturesEnglish68If your radio is set to Silent, it does not display any audio or visual indicators during Emergency mode, or allow any received calls to sound through the radio’s speaker, until you press the PTT button to initiate the call.If your radio is set to Silent with Voice, it does not display any audio or visual indicators during Emergency mode, but allow incoming calls to sound through the radio’s speaker. The indicators only appear once you press the PTT button to initiate, or respond to, the call.Sending an Emergency Alarm with Voice to Follow This feature allows you to send an Emergency Alarm to a group of radios. Your radio’s microphone is automatically activated, allowing you to communicate with the group of radios without pressing the PTT button.This activated microphone state is also known as “hot mic”.If your radio has Emergency Cycle Mode enabled, repetitions of hot mic and receiving period are made for a programmed duration.NOTE: During Emergency Cycle Mode, received calls sound through the radio’s speaker.If you press the PTT button during the programmed receiving period, you will hear a prohibit tone, indicating that you should release the PTT button. The radio ignores the PTT press and remains in Emergency mode.NOTE: If you press the PTT button during hot mic, and continue to press it after the hot mic duration expires, the radio continues to transmit until you release the PTT button.Procedure: 1Press the programmed Emergency On button.
Advanced FeaturesEnglish692The display shows Tx Alarm and the destination alias. The LED lights up solid green and the Emergency icon appears.ORThe display shows Tx Telegram and the destination alias. The LED lights up solid green and the Emergency icon appears.3Once the display shows Alarm Sent, speak clearly into the microphone. When hot mic has been enabled, the radio automatically transmits without a PTT press until the hot mic duration expires.While transmitting, the LED lights up solid green and the Emergency icon appears.4The radio automatically stops transmitting when:Once the cycling duration between hot mic and receiving calls expires, if Emergency Cycle Mode is enabled.OROnce the hot mic duration expires, if Emergency Cycle Mode is disabled.5To transmit again, press the PTT button.ORPress the programmed Emergency Off button to exit the Emergency mode.6The radio returns to the Home screen.If your radio is set to Silent, it does not display any audio or visual indicators during Emergency mode, or allow any received calls to sound through the radio’s speaker, until the programmed hot mic transmission period is over, and you press the PTT button.If your radio is set to Silent with Voice, it does not display any audio or visual indicators during Emergency mode when you are making the call with hot mic, but allow sound through the radio’s speaker when the target radio responds after the programmed hot mic transmission period is over. The indicators only appear when you press the PTT button.NOTE: If the Emergency Alarm request fails, the radio does not retry to send the request, and enters the hot mic state directly.
Advanced FeaturesEnglish70Reinitiating an Emergency ModeNOTE: This feature is only applicable to the radio sending the Emergency Alarm.There are two instances where this can happen:•You change the channel while the radio is in Emergency mode. This exits the Emergency mode. If Emergency Alarm is enabled on this new channel, the radio reinitiates Emergency.•You press the programmed Emergency On button during an Emergency initiation/transmission state. This causes the radio to exit this state, and to reinitiate Emergency.Exiting Emergency ModeNOTE: This feature is only applicable to the radio sending the Emergency Alarm.Your radio exits Emergency mode when one of the following occurs:•Emergency Alarm acknowledgement is received (for Emergency Alarm only), OR•An Emergency Exit Telegram is received, OR•All retries to send the alarm have been exhausted, OR•The Emergency Off button is pressed, OR•Turn the radio off and then power it on again if your radio has been programmed to remain on the Emergency Revert channel even after acknowledgement is received. NOTE: If your radio is powered off, it exits the Emergency mode. The radio does not reinitiate the Emergency mode automatically when it is turned on again.If you change channels when your radio is in Emergency mode to a channel that has no emergency system configured, No Emergency is shown on your display. 
Advanced FeaturesEnglish71 Man DownThis feature prompts an emergency to be raised if there is a change in the radio’s motions, such as the radio’s tilt, motion and/or the lack of motion for a predefined time.Following a change in the radio’s motion for a programmed duration, the radio pre-warns the user via an audio indicator indicating that a change in motion is detected.If there is still no acknowledgment by the user before the predefined reminder timer expires, the radio initiates an Emergency Alarm or an Emergency Call.Turning the Man Down Feature On or OffProcedure: Press the programmed Man Down button to toggle the feature on or off.ORFollow the procedure below.1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Man Down and press c to select.5Press c to enable Man Down. The display shows 9 beside Enabled.ORPress c to disable Man Down. The 9 disappears from beside Enabled.NOTE: At Step 4, you can also use < or > to change the selected option.If you disable the Man Down feature, the programmed alert tone sounds repeatedly until the Man Down feature is enabled.A device failure tone sounds when the Man Down feature fails while powering up. The device failure tone will continue until the radio resumes normal operation.
Advanced FeaturesEnglish72Text Message Features Your radio is able to receive data, for example a text message, from another radio or an e-mail application.The maximum length of characters for sending a text message, including the subject line (seen when receiving message from an e-mail application), is 140, whereas to receive would be a maximum of 280 characters. The radio exits the current screen once the inactivity timer expires. Any text message in the writing/editing screen is automatically saved to the Drafts folder.NOTE: Long press d at any time to return to the Home screen.Writing and Sending a Text MessageProcedure:Press the programmed Text Message button and proceed to Step 3.ORFollow the procedure below.1c to access the menu.2^ or v to Messages and press c to select.3^ or v to Compose and press c to select.4A blinking cursor appears. Use the keypad to type your message.Press < to move one space to the left. Press > or # to move one space to the right.Press * to delete any unwanted characters.Long press # to change text entry method.5Press c once message is composed.6^ or v to the required alias or ID and press c to select.OR^ or v to Manual Dial and press c to select.The first line of the display shows Radio Number:. The second line of the display shows a blinking cursor. Key in the subscriber ID and press c.ORd to edit the message.d again to discard the message or save it to the Drafts folder.7The display shows transitional mini notice, confirming your message is being sent.8If the message is sent, a tone sounds and the display shows positive mini notice.ORIf the message is not sent, a low tone sounds and the display shows negative mini notice.
Advanced FeaturesEnglish73If the text message fails to send, the radio returns you to the Resend option screen (see Managing Fail-to-Send Text Messages on page 76).Sending a Quick Text MessageYour radio supports a maximum of 50 Quick Text messages as programmed by your dealer. While Quick Text messages are predefined, you can edit each message before sending it.Procedure: Press the programmed Text Message button and proceed to Step 3.OR Follow the procedure below.1c to access the menu.2^ or v to Messages and press c to select.3^ or v to Quick Text and press c to select.4^ or v to the required Quick Text and press c to select.5A blinking cursor appears. Use the keypad to edit the message, if required. Press < to move one space to the left. Press > or # to move one space to the right.Press * to delete any unwanted characters.Long press # to change text entry method.6Press c once message is composed.7^ or v to the required alias or ID and press c to select.OR^ or v to Manual Dial and press c to select. The first line of the display shows Radio Number:. The second line of the display shows a blinking cursor. Key in the subscriber alias or ID and press c.ORd to edit the message.d again to discard the message or save it to the Drafts folder.8The display shows transitional mini notice, confirming your message is being sent.9If the message is sent, a tone sounds and the display shows positive mini notice.ORIf the message is not sent, a low tone sounds and the display shows negative mini notice.If the text message fails to send, the radio returns you to the Resend option screen (see Managing Fail-to-Send Text Messages on page 76).
Advanced FeaturesEnglish74Sending a Quick Text Message with the One Touch Access ButtonProcedure:1Press the programmed One Touch Access button to send a predefined Quick Text message to a predefined alias or ID.2The display shows transitional mini notice, confirming your message is being sent.3If the message is sent, a tone sounds and the display shows positive mini notice.ORIf the message is not sent, a low tone sounds and the display shows negative mini notice.If the text message fails to send, the radio returns you to the Resend option screen (see Managing Fail-to-Send Text Messages on page 76).Accessing the Drafts FolderYou can save a text message to send it at a later time.If a PTT button press or a mode change causes the radio to exit the text message writing/editing screen while you are in the process of writing or editing a text message, your current text message is automatically saved to the Drafts folder.The most recent saved text message is always added to the top of the Drafts list.The Drafts folder stores a maximum of ten (10) last saved messages. When the folder is full, the next saved text message automatically replaces the oldest text message in the folder.NOTE: Long press d at any time to return to the Home screen.Viewing a Saved Text MessageProcedure:Press the programmed Text Message button and proceed to Step 3.ORFollow the procedure below.1c to access the menu.2^ or v to Messages and press c to select.3^ or v to Drafts and press c to select.4^ or v to the required message and press c to select.
Advanced FeaturesEnglish75Editing and Sending a Saved Text MessageProcedure: 1Press c again while viewing the message.2^ or v to Edit and press c to select.A blinking cursor appears. Use the keypad to edit your message.Press < to move one space to the left. Press > or # to move one space to the right.Press * to delete any unwanted characters.Long press # to change text entry method.Press c once message is composed.3^ or v to the required alias or ID and press c to select.OR^ or v to Manual Dial and press c to select. Key in the subscriber alias or ID and press c.4The display shows transitional mini notice, confirming your message is being sent.5If the message is sent, a tone sounds and the display shows positive mini notice.ORIf the message is not sent, a low tone sounds and the display shows negative mini notice.If the text message fails to send, it is moved to the Sent Items folder and marked with a Send Failed icon.Deleting a Saved Text Message from DraftsProcedure:Press the programmed Text Message button and proceed to Step 3.ORFollow the procedure below.1c to access the menu.2^ or v to Messages and press c to select.3^ or v to Drafts and press c to select.4^ or v to the required message and press c to select.5Press c again while viewing the message.6^ or v to Delete and press c to delete the text message.
Advanced FeaturesEnglish76Managing Fail-to-Send Text MessagesYou can select one of the following options while at the Resend option screen:•Resend•Forward•EditNOTE: If the channel type (i.e. conventional digital or Capacity Plus or Linked Capacity Plus) is not a match, you can only edit and forward a Fail-to-Send message.Resending a Text MessageProcedure: 1Press c to resend the same message to the same subscriber/group alias or ID.2If the message is sent, a tone sounds and the display shows positive mini notice.ORIf the message is not sent, a low tone sounds and the display shows negative mini notice.Forwarding a Text MessageSelect Forward to send the message to another subscriber/group alias or ID.Procedure:1^ or v to Forward and press c to select.2^ or v to the required alias or ID and press c to select.OR^ or v to Manual Dial and press c to select. The first line of the display shows Radio Number:. The second line of the display shows a blinking cursor. Key in the subscriber ID and press c.3The display shows transitional mini notice, confirming your message is being sent.4If the message is sent, a tone sounds and the display shows positive mini notice.ORIf the message is not sent, a low tone sounds and the display shows negative mini notice.
Advanced FeaturesEnglish77Editing a Text MessageSelect Edit to edit the message before sending it.NOTE: If a subject line is present (for messages received from an e-mail application), you cannot edit it.Procedure:1^ or v to Edit and press c to select.2A blinking cursor appears. Use the keypad to edit your message.Press < to move one space to the left. Press > or # to move one space to the right.Press * to delete any unwanted characters.Long press # to change text entry method.3Press c once message is composed.4^ or v to Send and press c to send the message.OR^ or v to Save and press c to save the message to the Drafts folder.ORd to edit the message.d again to delete the message or save it to the Drafts folder.5^ or v to the required alias or ID and press c to select.OR^ or v to Manual Dial and press c to select. The first line of the display shows Radio Number:. The second line of the display shows a blinking cursor. Key in the subscriber ID and press c.6The display shows transitional mini notice, confirming your message is being sent.7If the message is sent, a tone sounds and the display shows positive mini notice.ORIf the message is not sent, a low tone sounds and the display shows negative mini notice.Managing Sent Text MessagesOnce a message is sent to another radio, it is saved in Sent Items. The most recent sent text message is always added to the top of the Sent Items list.The Sent Items folder is capable of storing a maximum of thirty (30) last sent messages. When the folder is full, the next sent text message automatically replaces the oldest text message in the folder.NOTE: Long press d at any time to return to the Home screen.
Advanced FeaturesEnglish78Viewing a Sent Text MessageProcedure:Press the programmed Text Message button and proceed to Step 3.ORFollow the procedure below.1c to access the menu.2^ or v to Messages and press c to select.3^ or v to Sent Items and press c to select.4^ or v to the required message and press c to select.A subject line may be shown if the message is from an e-mail application.The icon beside each message indicates the status of the message (see Sent Item Icons on page 19).Sending a Sent Text MessageYou can select one of the following options while viewing a sent text message:•Resend•Forward•Edit•DeleteNOTE: If the channel type (i.e. conventional digital or Capacity Plus or Linked Capacity Plus) is not a match, you can only edit, forward, or delete a Sent message.Procedure: 1Press c again while viewing the message.2^ or v to Resend and press c to select.3The display shows transitional mini notice, confirming that the same message is being sent to the same target radio.4If the message is sent, a tone sounds and the display shows positive mini notice.ORIf the message is not sent, a low tone sounds and the display shows negative mini notice.If the message fails to send, the radio returns you to the Resend option screen. Press c to resend the message to the same subscriber/group alias or ID.NOTE: Changing the volume, and pressing any button, except for c, <, or >, returns you to the message.The radio exits the Resend option screen if you press the PTT button to initiate a Private or Group Call, or to respond to a Group Call. The radio also exits the screen when it receives a text or telemetry message, an emergency call or alarm, or a call alert.
Advanced FeaturesEnglish79The display returns to the Resend option screen if you press the PTT button to respond to a Private Call (except when the radio is displaying the Missed Call screen), and at the end of an All Call.Press ^ or v to access the Forward, Edit, or Delete option screen:•Select Forward to send the selected text message to another subscriber/group alias or ID (see Forwarding a Text Message on page 76).•Select Edit to edit the selected text message before sending it (see Editing a Text Message on page 77).•Select Delete to delete the text message.NOTE: If you exit the message sending screen while the message is being sent, the radio updates the status of the message in the Sent Items folder without providing any indication in the display or via sound.If the radio changes mode or powers down before the status of the message in Sent Items is updated, the radio cannot complete any In-Progress messages and automatically marks it with a Send Failed icon.The radio supports a maximum of five (5) In-Progress messages at one time. During this period, the radio cannot send any new message and automatically marks it with a Send Failed icon.Deleting All Sent Text Messages from Sent Items Procedure:Press the programmed Text Message button and proceed to Step 3.ORFollow the procedure below.1c to access the menu.2^ or v to Messages and press c to select.3^ or v to Sent Items and press c to select.4^ or v to Delete All and press c to select.5 ^ or v to Yes and press c to select. The display shows positive mini noticeOR^ or v to No and press c to return to the previous screen.When you select Sent Items and it contains no text messages, the display shows List Empty, and sounds a low tone if Keypad Tones are turned on (see Turning Keypad Tones On or Off on page 95).
Advanced FeaturesEnglish80Receiving a Text MessageWhen your radio receives a message, the display shows the Notification List with the alias or ID of the sender and the message icon.You can select one of the following options when receiving a text message:•Read•Read Later•DeleteNOTE: The radio exits the Text Message alert screen and sets up a Private or Group Call to the sender of the message if the PTT button is pressed when the radio is displaying the alert screen.Reading a Text MessageProcedure: 1^ or v to Read? and press c to select.2Selected message in the Inbox opens. A subject line may be shown if the message is from an e-mail application.3Press d to return to the Inbox.ORPress c to reply, forward, or delete the text message.Press ^ or v to access the Read Later or Delete option screen:•Select Read Later to return to the screen you were on prior to receiving the text message. •Select Delete to delete the text message.Managing Received Text MessagesUse the Inbox to manage your text messages. The Inbox is capable of storing a maximum of 30 messages.Your radio supports the following options for text messages:•Reply•Forward•Delete•Delete AllNOTE: If the channel type (i.e. conventional digital or Capacity Plus or Linked Capacity Plus) is not a match, you can only forward, delete, or delete all Received messages.Text messages in the Inbox are sorted according to the most recently received.NOTE: Long press d at any time to return to the Home screen.
Advanced FeaturesEnglish81Viewing a Text Message from the InboxProcedure: 1c to access the menu.2^ or v to Messages and press c to select.3^ or v to Inbox and press c to select.4^ or v to view the messages. A subject line may be shown if the message is from an e-mail application.5Press c to select the current message, and press c again to reply, forward, or delete that message.ORLong press d to return to the Home screen.Viewing a Telemetry Status Text Message from the InboxProcedure: 1c to access the menu.2^ or v to Messages and press c to select.3^ or v to Inbox and press c to select.4^ or v to the required message and press c to select.5The display shows Telemetry: <Status Text Message>.6Long press d to return to the Home screen.You cannot reply to a Telemetry Status text message.Replying to a Text Message from the InboxProcedure: Press the programmed Text Message button and proceed to Step 3.OR Follow the procedure below.1c to access the menu.2^ or v to Messages and press c to select.3^ or v to Inbox and press c to select.4^ or v to the required message and press c to select.A subject line may be shown if the message is from an e-mail application.5Press c once more to access the sub-menu.6^ or v to Reply and press c to select.OR^ or v to Quick Reply and press c to select. A blinking cursor appears. Use the keypad to edit your message, if required.
Advanced FeaturesEnglish827Press c once message is composed.8The display shows transitional mini notice, confirming your message is being sent.9If the message is sent, a tone sounds and the display shows positive mini notice.ORIf the message is not sent, a low tone sounds and the display shows negative mini notice.If the message fails to send, the radio returns you to the Resend option screen (see Managing Fail-to-Send Text Messages on page 76).Deleting a Text Message from the InboxProcedure: Press the programmed Text Message button and proceed to Step 3.OR Follow the procedure below.1c to access the menu.2^ or v to Messages and press c to select.3^ or v to Inbox and press c to select.4^ or v to the required message and press c to select.A subject line may be shown if the message is from an e-mail application.5Press c once more to access the sub-menu.6^ or v to Delete and press c to select.7^ or v to Yes and press c to select. 8The display shows positive mini notice.9The screen returns to the Inbox.
Advanced FeaturesEnglish83Deleting All Text Messages from the InboxProcedure:Press the programmed Text Message button and proceed to Step 3.OR Follow the procedure below.1c to access the menu.2^ or v to Messages and press c to select.3^ or v to Inbox and press c to select.4^ or v to Delete All and press c to select.5^ or v to Yes and press c to select. 6The display shows positive mini notice.When you select the Inbox and it contains no text messages, the display shows List Empty, and sounds a low tone if Keypad Tones are turned on (see Turning Keypad Tones On or Off on page 95).Analog Message Encode Your radio is able to send preprogrammed messages from the Message list to a radio alias or to the dispatcher.Sending MDC Message Encode to DispatcherProcedure:1^ or v to Message and press c to select.2^ or v to Quick Text and press c to select.3^ or v to the required message. Press c to send.4 The display shows transitional mini notice, confirming your message is being sent.5If the message is sent, a tone sounds and the display shows positive mini notice. ORIf the message is not sent, a low tone sounds and the display shows negative mini notice. 
Advanced FeaturesEnglish84Analog Status Update Your radio is able to send preprogrammed messages from the Status List indicating your current activity to the dispatcher.The last acknowledged message is kept at the top of the Status List. The other messages are arranged in alphanumeric order. Sending Status Update to Predefined ContactProcedure:1^ or v to Status and press c to select.2^ or v to the required status. Press c to select. 3^ or v to Set as Default. Press c to send the status update. 4The display shows transitional mini notice, confirming your status update is being sent.5If the status update is acknowledged, a tone sounds and the display shows positive mini notice. A 9 appears beside the acknowledged status.ORIf the status update is not acknowledged, a low tone sounds and the display shows negative mini notice. A 9 remains beside the previous status.Privacy If enabled, this feature helps to prevent eavesdropping by unauthorized users on a channel by the use of a software-based scrambling solution. The signaling and user identification portions of a transmission are not scrambled.Your radio must have privacy enabled on the channel to send a privacy-enabled transmission, although this is not a necessary requirement for receiving a transmission. While on a privacy-enabled channel, the radio is still able to receive clear (unscrambled) transmissions.Your radio supports two types of privacy:•Basic Privacy•Enhanced Privacy. Only ONE of the privacy types above can be assigned to the radio.To unscramble a privacy-enabled call or data transmission, your radio must be programmed to have the same Privacy Key (for Basic Privacy), OR the same Key Value and Key ID (for Enhanced Privacy) as the transmitting radio.If your radio receives a scrambled call that is of a different Privacy Key, OR a different Key Value and Key ID, you will either hear a garbled transmission (Basic Privacy) or nothing at all (Enhanced Privacy).
Advanced FeaturesEnglish85The LED lights up solid green while the radio is transmitting and double blinks green when the radio is receiving an ongoing privacy-enabled transmission.NOTE: Some radio models may not offer this Privacy feature. Check with your dealer or system administrator for more information.Procedure:Press the programmed Privacy button to toggle privacy on or off.OR Follow the procedure below.1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Privacy.5Press c to enable Privacy. The display shows 9 beside Enabled.ORPress c to disable Privacy. The 9 disappears from beside Enabled.If the radio has a privacy type assigned, the secure or unsecure icon appears on the status bar, except when the radio is sending or receiving an Emergency call or alarm.NOTE: At Step 4, you can also use < or > to change the selected option.Dual Tone Multi Frequency (DTMF)The Dual Tone Multi Frequency (DTMF) feature allows the radio to operate in a radio system with an interface to telephone systems.Procedure:To initiate a DTMF call.1Press and hold the PTT button.2Enter the desired number, * or #.You can turn off the DTMF tone by disabling all radio tones and alerts (see Turning the Radio Tones/Alerts On or Off on page 95).
Advanced FeaturesEnglish86Multi-Site Controls These features are applicable when your current radio channel is part of an IP Site Connect or Linked Capacity Plus configuration. See IP Site Connect on page 13 and Linked Capacity Plus on page 15 for more details about these configurations.Starting an Automatic Site SearchNOTE: The radio only scans for a new site if the current signal is weak or when the radio is unable to detect any signal from the current site. If the RSSI value is strong, the radio remains on the current site.Procedure: Press the programmed Site Lock On/Off button.1A tone sounds and the display shows Site Unlocked.2The LED blinks yellow rapidly when the radio is actively searching for a new site, and turns off once the radio locks on to a site.3The display shows the channel alias and the site roaming icon appears.ORProcedure: Use the menu.1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Site Roaming and press c to select.5^ or v to Unlock Site and press c to select. A tone sounds and the display shows Site Unlocked.6The radio returns to the Home screen. The display shows the channel alias and the site roaming icon appears.7The LED blinks yellow rapidly when the radio is actively searching for a new site, and turns off once the radio locks on to a site.The radio also performs an automatic site search (site is unlocked) during a PTT button press or data transmission if the current channel, a multi-site channel with an attached roam list, is out of range.
Advanced FeaturesEnglish87Stopping an Automatic Site SearchWhen the radio is actively searching for a new site:Procedure: Press the programmed Site Lock On/Off button.1A tone sounds and the display shows Site Locked.2The LED turns off and the display shows the channel alias.ORProcedure: Use the menu.1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Site Roaming and press c to select.5^ or v to Lock Site State. c6Press c to lock site. The display shows 9 beside Enabled.ORPress c to unlock site. The 9 disappears from beside Enabled. The LED turns off and the radio returns to the Home screen. The display shows the channel alias. NOTE: At Step 5, you can also use < or > to change the selected option.Starting a Manual Site SearchProcedure: Press the programmed Manual Site Roam button and proceed to Step 6.ORFollow the procedure below.1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Site Roaming and press c to select.5^ or v to Active Search and press c to select.6A tone sounds and the display shows Finding Site.The LED blinks green.
Advanced FeaturesEnglish887If a new site is found, a tone sounds and the LED turns off. The display shows Site <Alias> Found. ORIf there is no available site within range, a tone sounds and the LED turns off. The display shows Out of Range.ORIf a new site is within range, but the radio is unable to connect to it, a tone sounds and the LED turns off. The display shows Channel Busy.8The radio returns to the Home screen.Security You can enable or disable any radio in the system. For example, you might want to disable a stolen radio, to prevent the thief from using it, and enable that radio, when it is recovered.NOTE: Performing Radio Disable and Enable is limited to radios with these functions enabled. Check with your dealer or system administrator for more information.Radio DisableProcedure: Use the programmed Radio Disable button.1Press the programmed Radio Disable button.2^ or v to the required alias or ID and press c to select.3The display shows transitional mini notice, indicating the request is in progress. The LED blinks green. 4Wait for acknowledgment.5If successful, a positive indicator tone sounds and the display shows positive mini notice.ORIf unsuccessful, a negative indicator tone sounds and the display shows negative mini notice.OR
Advanced FeaturesEnglish89Procedure: Use the menu.1c to access the menu.2^ or v to Contacts and press c to select. The entries are alphabetically sorted.3^ or v to the required alias or ID and press c to select.OR^ or v to Manual Dial and press c to select. ^ or v to Radio Contact and press c to select.The first line of the display shows Radio Number:. The second line of the display shows a blinking cursor.Key in the subscriber alias or ID and press c.4^ or v to Radio Disable and press c to select. 5 The display shows transitional mini notice, indicating the request is in progress. The LED blinks green.6Wait for acknowledgment.7If successful, a positive indicator tone sounds and the display shows positive mini notice.ORIf unsuccessful, a negative indicator tone sounds and the display shows negative mini notice.Do not press d during the Radio Disable operation as you will not get an acknowledgement message.Radio EnableProcedure: Use the programmed Radio Enable button.1Press the programmed Radio Enable button.2^ or v to the required alias or ID and press c to select.3 The display shows Radio Enable and the subscriber alias or ID. The LED lights up solid green.4Wait for acknowledgment.5If successful, the radio sounds a positive indicator tone and the display shows positive mini notice.ORIf unsuccessful, the radio sounds a negative indicator tone and the display shows negative mini notice.ORProcedure: Use the menu.1c to access the menu.2^ or v to Contacts and press c to select. The entries are alphabetically sorted.3^ or v to the required alias or ID and press c to select.OR^ or v to Manual Dial and press c to select.
Advanced FeaturesEnglish90^ or v to Radio Contact and press c to select.The first line of the display shows Radio Number:. The second line of the display shows a blinking cursor. Key in the subscriber alias or ID and press c.4^ or v to Radio Enable and press c to select.5 The display shows Radio Enable and the subscriber alias or ID. The LED lights up solid green.6Wait for acknowledgment.7If successful, the radio sounds a positive indicator tone and the display shows positive mini notice.ORIf unsuccessful, the radio sounds a negative indicator tone and the display shows negative mini notice.Do not press d during the Radio Enable operation as you will not get an acknowledgement message.Lone WorkerThis feature prompts an emergency to be raised if there is no user activity, such as any radio button press or activation of the channel selector, for a predefined time.Following no user activity for a programmed duration, the radio pre-warns the user via an audio indicator once the inactivity timer expires.If there is still no acknowledgment by the user before the predefined reminder timer expires, the radio initiates an Emergency Alarm.Only one of the following Emergency Alarms is assigned to this feature:•Emergency Alarm•Emergency Alarm with Call•Emergency Alarm with Voice to Follow The radio remains in the emergency state allowing voice messages to proceed until action is taken. See Emergency Operation on page 65 on ways to exit Emergency.NOTE: This feature is limited to radios with this function enabled. Check with your dealer or system administrator for more information.
Advanced FeaturesEnglish91Password Lock FeaturesIf enabled, this feature allows you to access your radio via password upon powering up.Accessing the Radio from PasswordProcedure:Power up the radio.1You hear a continuous tone. 2Enter your current four-digit password with the radio’s keypad. The display shows . Press c to proceed.OREnter your current four-digit password. Press ^ or v to edit each digit’s numeric value. Press > or c to move to the next digit. Each digit changes to . Press c to confirm your selection. You hear a positive indicator tone for every digit pressed. Press < to remove the each  on the display. You hear a negative indicator tone, if you press < when the line is empty, or if you press more than four digits.3If the password is correct:Your radio proceeds to power up. See Powering Up the Radio on page 5.ORIf the password is incorrect:The display shows Wrong Password. Repeat Steps 2.ORAfter the third incorrect password, the display shows Wrong Password and then, shows Radio Locked. A tone sounds and the LED double blinks yellow.Your radio enters into locked state for 15 minutes, and responds to inputs from On/Off/Volume Control Knob and programmed Backlight Auto button only.NOTE: The radio is unable to receive any call, including emergency calls, in locked state.Unlocking the Radio from Locked StateProcedure:Wait for 15 minutes. Repeat Steps 1 to 3 in Accessing the Radio from Password on page 91.ORPower up the radio, if you have powered down the radio during locked state:1A tone sounds and the LED double blinks yellow. The display shows Radio Locked.2Wait for 15 minutes. Repeat Accessing the Radio from Password on page 91.
Advanced FeaturesEnglish92Your radio restarts the 15 minutes timer for locked state when you power up.Turning the Password Lock On or OffProcedure:1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Passwd Lock and press c to select.5Enter your current four-digit password.See Step 2 in Accessing the Radio from Password on page 91.6If the password is correct: Press c to enable Password Lock. The display shows 9 beside Enabled.ORPress c to disable Password Lock. The 9 disappears from beside Enabled.ORIf the password is incorrect:The display shows Wrong Password and automatically returns to the previous menu.NOTE: At Step 6, you can also use < or > to change the selected option.Changing the PasswordProcedure:1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Passwd Lock and press c to select.5Enter your current four-digit password.See Step 2 in Accessing the Radio from Password on page 91.6If the password is correct:^ or v to Change Pwd and press c to select.ORIf the password is incorrect:The display shows Wrong Password and automatically returns to the previous menu.7Enter a new four-digit password. See Step 2 in Accessing the Radio from Password on page 91.8Re-enter the new four-digit password. See Step 2 in Accessing the Radio from Password on page 91.
Advanced FeaturesEnglish939If both of the new password inputs match:The display shows Password Changed.ORIf both of the new password inputs do not match:The display shows Passwords Do Not Match.10 The screen automatically returns to the previous menu. Notification ListYour radio has a Notification List that collects all your “unread” events on the channel, such as unread text messages, telegrams, telemetry messages, missed calls, and call alerts. The Notification icon appears on the status bar when the Notification List has one or more events. The list supports a maximum of forty (40) unread events. When it is full, the next event automatically replaces the oldest event. After the events are read, they are removed from the Notification List.NOTE: Your radio suspends Scan when the Notification List is displayed. Scanning resumes when your radio exits the Notification List. Press d to exit the Notification List or wait for the menu timer to expire.Accessing the Notification ListProcedure:Press the programmed Notifications button.ORFollow the procedure below.1c to access the menu.2^ or v to Notification and press c to select.
Advanced FeaturesEnglish943^ or v to the required event and press c to select.Long press d to return to the Home screen.Auto-Range Transponder System (ARTS)ARTS is an analog-only feature designed to inform you when your radio is out-of-range of other ARTS-equipped radios.ARTS-equipped radios transmit or receive signals periodically to confirm that they are within range of each other. Your dealer can program your radio to transmit or receive the ARTS signal. Your radio provides indications of states as follows:•First-Time Alert – A tone sounds and the display shows In Range after the channel alias.•ARTS-in-Range Alert – A tone sounds, if programmed, and the display shows In Range after the channel alias. •ARTS-Out-of-Range Alert – A tone sounds, the LED rapidly blinks red, and the display alternates between Out of Range and the home screen.Over-the-Air Programming (OTAP)Your radio can be updated by your dealer remotely, via OTAP, without needing to be physically connected. Additionally, some settings can also be configured via OTAP. While undergoing OTAP, the LED blinks green. NOTE: When the radio is receiving high volume data, the High Volume Data icon appears and channel is busy. A PTT button press at this time causes a negative tone to sound. Once the programming is complete, depending on your radio’s configuration:•A tone sounds, the display shows Updating Restarting, and your radio restarts (powers off and on again). •Select between Restart Now or Postpone. Selecting Postpone allows your radio to return to the previous display, with an OTAP Timer icon visible, for a period of time before the automatic restart occurs. Upon power up after the automatic restart occurs, the display shows Sw Update Completed if the OTAP update is successful or Sw Update Failed if the OTAP update is unsuccessful. See Software Update on page 112 for your updated software version.
Advanced FeaturesEnglish95UtilitiesTurning the Radio Tones/Alerts On or OffYou can enable and disable all radio tones and alerts (except for the incoming Emergency alert tone) if needed.Procedure: Press the programmed All Tones/Alerts button to toggle all tones on or off.ORFollow the procedure below.1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Tones/Alerts and press c to select.5^ or v to All Tones and press c to select.6Press c to enable all tones. The display shows 9 beside Enabled.ORPress c to disable all tones. The 9 disappears from beside Enabled.NOTE: At Step 5, you can also use < or > to change the selected option.Turning Keypad Tones On or OffYou can enable and disable keypad tones if needed.Procedure: 1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Tones/Alerts and press c to select.5^ or v to Keypad Tones and press c to select.6Press c to enable keypad tones. The display shows 9 beside Enabled.ORPress c to disable keypad tones. The 9 disappears from beside Enabled.NOTE: At Step 5, you can also use < or > to change the selected option.
Advanced FeaturesEnglish96Setting the Tone Alert Volume Offset Level You can adjust the Tone Alert Volume Offset level if needed. This feature adjusts the volume of the tones/alerts, allowing it to be higher or lower than the voice volume.Procedure: 1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Tones/Alerts and press c to select.5^ or v to Vol. Offset and press c to select.6^ or v to the required volume value. The radio sounds a feedback tone with each corresponding volume value.7Press c to keep the required displayed volume value. ORRepeat Step 6 to select another volume value.ORd to exit without changing the current volume offset settings.Turning the Talk Permit Tone On or Off You can enable and disable the Talk Permit Tone if needed.Procedure: 1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Tones/Alerts and press c to select.5^ or v to Talk Permit and press c to select.6Press c to enable Talk Permit Tone. The display shows 9 beside Enabled.ORPress c to disable Talk Permit Tone. The 9 disappears from beside Enabled.NOTE: At Step 5, you can also use < or > to change the selected option.
Advanced FeaturesEnglish97Turning the Power Up Tone On or Off You can enable and disable the Power Up Tone if needed. 1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Tones/Alerts and press c to select.5^ or v to Power Up and press c to select.6Press c to enable Power Up Tone. The display shows 9 beside Enabled.ORPress c to disable Power Up Tone. The 9 disappears from beside Enabled.NOTE: At Step 5, you can also use < or > to change the selected option.Changing the Display ModeYou can change radio’s display mode between Day or Night, as needed. This affects the color palette of the display.Procedure: Press the programmed Display Mode button to toggle the display mode settings.ORFollow the procedure below.1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Day/Night and press c to select.5The display shows Day Mode and Night Mode. ^ or v to the required setting and press c to enable. 9 appears beside selected setting.NOTE: At Step 4, you can also use < or > to change the selected option.
Advanced FeaturesEnglish98Adjusting the Display BrightnessYou can adjust radio’s display brightness as needed.Procedure: Press the programmed Brightness button and proceed to Step 5.ORFollow the procedure below.1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Brightness and press c to select.5The display shows a progress bar. Decrease display brightness by pressing < or increase the display brightness by pressing >. Press c to confirm your entry. Controlling the Display BacklightYou can enable or disable the radio’s display backlight as needed. The setting also affects the Menu Navigation Buttons and keypad backlighting accordingly. Procedure: Press the programmed Backlight Auto button to toggle the backlight settings.ORFollow the procedure below.1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Backlight Auto5Press c to enable backlight. The display shows 9 beside Enabled.ORPress c to disable backlight. The 9 disappears from beside Enabled.The display backlight and keypad backlighting are automatically turned off if the LED indicator is disabled (see Turning the LED Indicator On or Off on page 101).
Advanced FeaturesEnglish99NOTE: At Step 4, you can also use < or > to change the selected option.Setting the Squelch Level You can adjust your radio's squelch level to filter out unwanted calls with low signal strength or channels that have a higher than normal background noise.Settings: Normal is the default. Tight filters out (unwanted) calls and/or background noise. However, calls from remote locations may also be filtered out.Procedure: Press the programmed Squelch button to toggle squelch level between normal and tight.ORFollow the procedure below.1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Squelch and press c to select.5The display shows Tight and Normal. ^ or v to the required setting and press c to enable. 9 appears besides selected setting. 6Screen returns to the previous menu.NOTE: At Step 4, you can also use < or > to change the selected option.Turning the Introduction Screen On or OffYou can enable and disable the Introduction Screen if needed.Procedure: 1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Intro Screen and press c to select.5Press c to enable Introduction Screen. The display shows 9 beside Enabled.ORPress c to disable Introduction Screen. The 9 disappears from beside Enabled.NOTE: At Step 4, you can also use < or > to change the selected option.
Advanced FeaturesEnglish100Locking and Unlocking the KeypadYou can lock your radio’s keypad to avoid inadvertent key entry.Procedure:1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Keypad Lock and press c to select.5The display shows Keypad Locked and returns to the Home screen.6To unlock the keypad, press c followed by *.7The display shows Keypad Unlocked and returns to the Home screen.NOTE: At Step 4, you can also use < or > to change the selected option.LanguageYou can set your radio display to be in your required language. Procedure: 1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Language and press c to select.4^ or v to the required language and press c to enable. 9 appears beside selected language.NOTE: At Step 4, you can also use < or > to change the selected option.Setting the Text Message Alert ToneYou can customize your radio’s text message alert tone to Momentary or Repetitive for each entry in the Contacts list.Procedure: 1c to access the menu.2^ or v to Contacts and press c to select.3^ or v to the required subscriber alias and press c to select.4^ or v to Message Alert and press c to select.
Advanced FeaturesEnglish1015The display shows Momentary and Repetitive. ^ or v to the required setting and press c to enable. 9 appears besides selected setting. The default setting in your radio is Repetitive.NOTE: At Step 4, you can also use < or > to change the selected option.Turning the LED Indicator On or OffYou can enable and disable the LED Indicator if needed.Procedure: 1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to LED Indicator and press c to select.5Press c to enable LED indicator. The display shows 9 beside Enabled.ORPress c to disable LED indicator. The 9 disappears from beside Enabled.The display backlight, buttons, and keypad backlighting are automatically turned off if the LED indicator is disabled (see Controlling the Display Backlight on page 98).NOTE: At Step 4, you can also use < or > to change the selected option.Turning the Voice Operating Transmission (VOX) Feature On or OffThis feature allows you to initiate a hands-free voice activated call on a programmed channel. The radio automatically transmits, for a programmed period, whenever the microphone on the VOX-capable accessory detects voice.Pressing the PTT button during radio operation disables VOX. To re-enable VOX, do one of the following:•Turn the radio off and power it on again, OR•Change the channel via the Channel Selector Knob, OR•Follow the procedure below.NOTE: Turning this feature on or off is limited to radios with this function enabled. Check with your dealer or system administrator for more information.Procedure: Press the programmed VOX button to toggle the feature on or off.
Advanced FeaturesEnglish102ORFollow the procedure below.1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to VOX.5Press c to enable VOX. The display shows 9 beside Enabled.ORPress c to disable VOX. The 9 disappears from beside Enabled.If the Talk Permit Tone feature is enabled (see Turning the Talk Permit Tone On or Off on page 96), use a trigger word to initiate the call. Wait for the Talk Permit Tone to finish before speaking clearly into the microphone.NOTE: At Step 4, you can also use < or > to change the selected option.Turning the Option Board Feature(s) On or OffOption board capabilities within each channel and can be assigned to programmable buttons. Refer to your dealer or system administrator for more information.Procedure: Press the programmed Option Board Feature button to toggle the feature on or off.Identifying Cable TypeYou can select the type of cable your radio uses.Procedure: 1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Cable Type and press c to select.5The current cable type is indicated by a 9.NOTE: At Step 4, you can also use < or > to change the selected option.
Advanced FeaturesEnglish103Voice AnnouncementThis feature enables the radio to audibly indicate the current Zone or Channel the user has just assigned, or programmable button press. This audio indicator can be customized per customer requirements. This is typically useful when the user is in a difficult condition to read the content shown on the display.Use the following features to toggle Voice Announcement on or off. Procedure: Press the programmed Voice Announcement button. ORFollow the procedure below.1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Voice Announcement.4Press c to enable Voice Announcement. The display shows 9 beside Enabled.ORPress c to disable Voice Announcement. The 9 disappears from beside Enabled.NOTE: At Step 3, you can also use < or > to change the selected option.Call ForwardingYou can enable your radio to automatically forward voice calls to another radio. Procedure: 1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Call Forward.4Press c to enable Call Forwarding. The display shows 9 beside Enabled.ORPress c to disable Call Forwarding. The 9 disappears from beside Enabled.NOTE: At Step 3, you can also use < or > to change the selected option.
Advanced FeaturesEnglish104Menu TimerSet the period of time your radio stays in the menu before it automatically switches to the Home screen. Procedure: 1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Menu Timer and press c to select.5^ or v to the required setting and press c to enable.Analog Mic AGC (Mic AGC-A)This feature controls the your radio's microphone gain automatically while transmitting on an analog system. It suppresses loud audio or boosts soft audio to a preset value in order to provide a consistent level of audio. Procedure: 1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Analog Mic AGC.5Press c to enable Analog Mic AGC. The display shows 9 beside Enabled.ORPress c to disable Analog Mic AGC. The 9 disappears from beside Enabled.NOTE: At Step 3, you can also use < or > to change the selected option.Digital Mic AGC (Mic AGC-D)This feature controls the your radio's microphone gain automatically while transmitting on an digital system. It suppresses loud audio or boosts soft audio to a preset value in order to provide a consistent level of audio. Procedure: 1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Digital Mic AGC.5Press c to enable Digital Mic AGC. The display shows 9 beside Enabled.OR
Advanced FeaturesEnglish105Press c to disable Digital Mic AGC. The 9 disappears from beside Enabled.NOTE: At Step 3, you can also use < or > to change the selected option.Intelligent AudioYour radio automatically adjusts its audio volume to overcome current background noise in the environment, inclusive of both stationary and non-stationary noise sources. This feature is a Receive-only feature and does not affect Transmit audio. Use the following features to toggle Intelligent Audio on or off. Procedure: Press the programmed Intelligent Audio button to toggle the feature on or off. ORFollow the procedure below.1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Intelligent Audio.5Press c to enable Intelligent Audio. The display shows 9 beside Enabled.ORPress c to disable Intelligent Audio. The 9 disappears from beside Enabled.NOTE: At Step 3, you can also use < or > to change the selected option.GPSGlobal Positioning System (GPS) is a satellite navigation system that determines the radio’s precise location. It is recommended you only disable GPS to save battery life when the GPS signal is unavailable.Procedure:Press the programmed GPS button to toggle the feature on or off.OR1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to GPS.5Press c to enable GPS. The display shows 9 beside Enabled.OR
Advanced FeaturesEnglish106Press c to disable GPS. The 9 disappears from beside Enabled.See Checking the GPS Information on page 111 for details on retrieving GPS information.NOTE: At Step 4, you can also use < or > to change the selected option.Text Entry ConfigurationYou can configure the following settings for entering text on your radio:•Word Correct•Word Predict•Sentence Cap•My WordsNOTE: Press d at any time to return to the previous screen or long press d to return to the Home screen. The radio exits the current screen once the inactivity timer expires.Word CorrectSupplies alternative word choices when the word entered into the text editor is not recognized by the in-built dictionary.1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Text Entry and press c to select.5^ or v to Word Correct and press c to select.6Press c to enable Word Correct. The display shows 9 beside Enabled.ORPress c to disable Word Correct. The 9 disappears from beside Enabled.NOTE: At Step 5, you can also use < or > to change the selected option.
Advanced FeaturesEnglish107Word PredictYour radio can learn common word sequences that you often enter. It then predicts the next word you may want to use after you enter the first word of a common word sequence into the text editor. 1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Text Entry and press c to select.5^ or v to Word Predict and press c to select.6Press c to enable Word Predict. The display shows 9 beside Enabled.ORPress c to disable Word Predict. The 9 disappears from beside Enabled.NOTE: At Step 5, you can also use < or > to change the selected option.Sentence CapAutomatically enables capitalization for the first letter in the first word for every new sentence.1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Text Entry and press c to select.5^ or v to Sentence Cap and press c to select.6Press c to enable Sentence Cap. The display shows 9 beside Enabled.ORPress c to disable Sentence Cap. The 9 disappears from beside Enabled.NOTE: At Step 5, you can also use < or > to change the selected option.
Advanced FeaturesEnglish108Viewing Custom WordsYou can add your own custom words into your radio’s in-built dictionary. Your radio maintains a list to contain these words.1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Text Entry and press c to select.5^ or v to My Words and press c to select.6^ or v to List of Words and press c to select.Display shows the list of custom words. Editing Custom WordYou can edit the custom words saved in your radio.1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Text Entry and press c to select.5^ or v to My Words and press c to select.6^ or v to List of Words and press c to select.Display shows the list of custom words. 7^ or v to the required word and press c to select.8^ or v to the Edit and press c to select.9Use the keypad to edit your custom word.Press < to move one space to the left. Press > or # to move one space to the right.Press * to delete any unwanted characters.Long press # to change text entry method.Press c once your custom word is complete.10 The display shows transitional mini notice, confirming your custom word is being saved.11 If the custom word is saved, a tone sounds and the display shows positive mini notice.ORIf the custom word is not saved, a low tone sounds and the display shows negative mini notice.Adding Custom WordsYou can add your own custom words into your radio’s in-built dictionary.1c to access the menu.
Advanced FeaturesEnglish1092^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Text Entry and press c to select.5^ or v to My Words and press c to select.6^ or v to Add New Word and press c to select. 7Use the keypad to enter your custom word.Press < to move one space to the left. Press > or # to move one space to the right.Press * to delete any unwanted characters.Long press # to change text entry method.Press c once your custom word is complete.8The display shows transitional mini notice, confirming your custom word is being saved.9If the custom word is saved, a tone sounds and the display shows positive mini notice.ORIf the custom word is not saved, a low tone sounds and the display shows negative mini notice.Deleting a Custom Word You can delete the custom words saved in your radio.1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Settings and press c to select.4^ or v to Text Entry and press c to select.5^ or v to My Words and press c to select.6^ or v to the required word and press c to select.7^ or v to Delete and press c to select.8At Delete Entry?, ^ or v to Yes and press c to select, to delete the entry. The display shows Entry Deleted. OR^ or v to No and press c to select to return to the previous screen.Deleting All Custom WordsYou can delete all custom words from your radio’s in-built dictionary.1c to access the menu.NOTE: ^ or v to Utilities and press c to select.
Advanced FeaturesEnglish110Accessing General Radio InformationYour radio contains information on the following:•Battery•Radio Alias and ID •Firmware and Codeplug Versions•GPS Information•Software Update•Site InformationNOTE: Press d at any time to return to the previous screen or long press d to return to the Home screen. The radio exits the current screen once the inactivity timer expires.Accessing the Battery InformationDisplays information on your radio battery.Procedure: 1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Info and press c to select.4^ or v to Battery Info and press c to select. 5The display shows the battery information.ORFor IMPRES batteries ONLY: The display reads Recondition Battery if the battery requires reconditioning in an IMPRES charger. After the reconditioning process, the display then shows the battery information.Checking the Radio Alias and ID Displays the ID of your radio. Procedure: Press the programmed Radio Alias and ID button to check your radio alias and ID. You hear a positive indicator tone.ORFollow the procedure below.1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Info and press c to select.4^ or v to My Number and press c to select.5The first line of the display shows the radio alias. The second line of the display shows the radio ID
Advanced FeaturesEnglish111You can also press the programmed Radio Alias and ID button to return to the previous screen.Checking the Firmware Version and Codeplug VersionDisplays the firmware and codeplug versions on your radio.Procedure: 1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Info and press c to select.4^ or v to Versions and press c to select.5The display shows the current firmware and codeplug versions.Checking the GPS InformationDisplays the GPS information on your radio, such as values of:•Latitude•Longitude•Altitude•Direction•Velocity•Horizontal Dilution of Precision (HDOP)•Satellites•VersionProcedure: 1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Info and press c to select.4^ or v to GPS Info and press c to select.5^ or v to the required item and press c to select.6The display shows the requested GPS information.See GPS on page 105 for details on GPS.
Advanced FeaturesEnglish112Software UpdateDisplays the date and time of the latest software update carried out via Over-the-Air Programming (OTAP). Procedure: 1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Info and press c to select.4^ or v to SW Update and press c to select.5The display shows the date and time of the latest software update.See Over-the-Air Programming (OTAP) on page 94 for details on OTAP.NOTE: Software Update menu is only available after at least one successful OTAP session. Site InformationDisplays the current Linked Capacity Plus site name your radio is on.Procedure: 1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Radio Info and press c to select.4^ or v to Site Info and press c to select.5The display shows the current Linked Capacity Plus site name.See Linked Capacity Plus on page 15 for details on Linked Capacity Plus.RSSI ValuesYour radio shows the Received Signal Strength Indicator (RSSI) icon at the top of your display. This feature allows you to view the RSSI values.Procedure:When you are on the Home screen:1Press < three times (<-<-<) and immediately press > three times (>->->), all within 5 seconds. 2The display shows the current RSSI values. Long press the d button to return to the Home screen.See Display Icons on page 16 for details on the RSSI icon.
Advanced FeaturesEnglish113Front Panel Configuration (FPC)Your radio is able to customize certain feature parameters to enhance the use of your radio. Entering FPC ModeProcedure:1c to access the menu.2^ or v to Utilities and press c to select.3^ or v to Program Radio and press c to select.NOTE: Long press d at any time to return to the Home screen.Editing FPC Mode ParametersUse the following buttons as required while navigating through the feature parameters. ^, v, <, > – Scroll through options, increase/decrease values, or navigate verticallyc – Select the option or enter a sub-menud – Short-press to return to previous menu or to exit the selection screen. Long-press to return to Home screen.
AccessoriesEnglish114AccessoriesYour radio is compatible with the accessories listed in this chapter. Contact your dealer for details.Antennas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 114Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 114Carry Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 114Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 115Earbuds and Earpieces. . . . . . . . . . . . . . . . . . . . . . . page 115Headsets and Headset Accessories . . . . . . . . . . . . . page 115Remote Speaker Microphones . . . . . . . . . . . . . . . . . page 115Miscellaneous Accessories. . . . . . . . . . . . . . . . . . . . page 115Antennas•UHF, 403-433MHz, GPS Folded Monopole Antenna EX (PMAE4018_)•UHF, 430-470MHz, GPS Folded Monopole Antenna EX (PMAE4024_)•UHF, 430-470MHz, GPS Stubby Antenna EX (PMAE4023_)•VHF, 136-147MHz, GPS Helical Antenna EX (PMAD4067)•VHF, 147-160MHz, GPS Helical Antenna EX (PMAD4068_)•VHF, 160-174MHz, GPS Helical Antenna EX (PMAD4069_)Batteries•MOTOTRBO CSA IMPRES Li-Ion, 2075mA (NNTN8386_)Carry Devices•2.5-Inch Replacement Swivel Belt Loop (PMLN5610_)•Hard Leather Carry Case with 2.5-Inch Swivel Belt Loop for Full-Keypad Radio (PMLN6097_)•Soft Leather Carry Case with 2.5-Inch Swivel Belt Loop for Full-Keypad Radio (PMLN6099_)•Belt Clip for 2.5-Inch Belt Width (PMLN6086_)
AccessoriesEnglish115Chargers•IMPRES Single-Unit Charger (WPLN4226_)•IMPRES Single-Unit Charger with Switch Mode Power Supply US Cord (WPLN4253_)•IMPRES Multi-Unit Charger with Display (WPLN4218_)•IMPRES Multi-Unit Charger non Display - NAG (WPLN4212_)•IMPRES Multi-Unit Charger with Display - NAG (WPLN4219_)Earbuds and Earpieces•Receive-Only Earpiece (RLN4941_)Headsets and Headset Accessories•Behind the Head Heavy Duty Headset (PMLN5275_)•Received-Only Headset (RMN4054_)•Standard Hardhat Mount Headset, 24 NRR (NNTN8379_)*•Standard Hardhat Mount Headset, 26 NRR (NNTN8380_)*Remote Speaker Microphones•IMPRES Noise Canceling Remote Speaker Microphone with Audio Jack (PMMN4050_)•IMPRES ATEX CSA Remote Speaker Microphone (PMMN4067_)Miscellaneous Accessories•Universal Connector Dust Cover for MOTOTRBO ATEX CSA (15012157001)•ATEX Adapter with Molex Jack (PMLN6047_)•CSA Push-to-Talk Adapter (NNTN8378_)* For use with NNTN8378_
Appendix: Maritime Radio Use in the VHF Frequency RangeEnglish116Appendix: Maritime Radio Use in the VHF Frequency RangeTake a moment to review the following:Special Channel Assignments. . . . . . . . . . . . . . . . . . page 116Operating Frequency Requirements. . . . . . . . . . . . . page 117Declaration of Compliance for the Use of Distress and Safety Frequencies. . . . . . . . . . . . . . page 119Technical Parameters for InterfacingExternal Data Sources. . . . . . . . . . . . . . . . . . . . . . page 120Special Channel AssignmentsEmergency ChannelIf you are in imminent and grave danger at sea and require emergency assistance, use VHF Channel 16 to send a distress call to nearby vessels and the United States Coast Guard. Transmit the following information, in this order:1“MAYDAY, MAYDAY, MAYDAY.”2“THIS IS _____________________, CALL SIGN __________.”State the name of the vessel in distress 3 times, followed by the call sign or other identification of the vessel, stated 3 times.3Repeat “MAYDAY” and the name of the vessel.4“WE ARE LOCATED AT _______________________.” State the position of the vessel in distress, using any information that will help responders to locate you, e.g.:• latitude and longitude• bearing (state whether you are using true or magnetic north)• distance to a well-known landmark• vessel course, speed or destination5State the nature of the distress.6Specify what kind of assistance you need.7State the number of persons on board and the number needing medical attention, if any.8Mention any other information that would be helpful to responders, such as type of vessel, vessel length and/or tonnage, hull color, etc.9“OVER.”10 Wait for a response.11 If you do not receive an immediate response, remain by the radio and repeat the transmission at intervals until you receive a response. Be prepared to follow any instructions given to you.
Appendix: Maritime Radio Use in the VHF Frequency RangeEnglish117Non-Commercial Call ChannelFor non-commercial transmissions, such as fishing reports, rendezvous arrangements, repair scheduling, or berthing information, use VHF Channel 9.Operating Frequency RequirementsA radio designated for shipboard use must comply with Federal Communications Commission Rule Part 80 as follows:•on ships subject to Part II of Title III of the Communications Act, the radio must be capable of operating on the 156.800 MHz frequency•on ships subject to the Safety Convention, the radio must be capable of operating:• in the simplex mode on the ship station transmitting frequencies specified in the 156.025 – 157.425 MHz frequency band, and• in the semiduplex mode on the two frequency channels specified in the table below.NOTE: Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters.Additional information about operating requirements in the Maritime Services can be obtained from the full text of FCC Rule Part 80 and from the US Coast Guard.Table A-1: VHF Marine Channel ListChannel NumberFrequency (MHz)Transmit Receive1 156.050 160.6502 156.100 160.700* 156.150 160.7504 156.200 160.8005 156.250 160.8506 156.300 –7 156.350 160.9508 156.400 –9 156.450 156.45010 156.500 156.50011 156.550 156.55012 156.600 156.60013** 156.650 156.65014 156.700 156.70015** 156.750 156.75016 156.800 156.80017** 156.850 156.85018 156.900 161.50019 156.950 161.550
Appendix: Maritime Radio Use in the VHF Frequency RangeEnglish118* Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters.** Low power (1 W) only*** Guard bandNOTE: A – in the Receive column indicates that the channel is transmit only.20 157.000 161.600* 157.050 161.65022 157.100 161.700* 157.150 161.75024 157.200 161.80025 157.250 161.85026 157.300 161.90027 157.350 161.95028 157.400 162.00060 156.025 160.625* 156.075 160.67562 156.125 160.72563 156.175 160.775* 156.225 160.82565 156.275 160.87566 156.325 160.92567** 156.375 156.37568 156.425 156.42569 156.475 156.47571 156.575 156.57572 156.625 –73 156.675 156.675Table A-1: VHF Marine Channel List (Continued)Channel NumberFrequency (MHz)Transmit Receive74 156.725 156.72575 *** ***76 *** ***77** 156.875 –78 156.925 161.52579 156.975 161.57580 157.025 161.625* 157.075 161.675* 157.125 161.725* 157.175 161.77584 157.225 161.82585 157.275 161.87586 157.325 161.92587 157.375 161.97588 157.425 162.025Table A-1: VHF Marine Channel List (Continued)Channel NumberFrequency (MHz)Transmit Receive
Appendix: Maritime Radio Use in the VHF Frequency RangeEnglish119Declaration of Compliance for the Use of Distress and Safety FrequenciesThe radio equipment does not employ a modulation other than the internationally adopted modulation for maritime use when it operates on the distress and safety frequencies specified in RSS-182 Section 7.3.Technical Parameters for Interfacing External Data SourcesRS232 USB SB9600Input Voltage (Volts Peak-to-peak)18V 3.6V 5VMax Data Rate 28 kb/s 12 Mb/s 9.6 kb/sImpedance 5k ohm 90 ohm 120 ohm
Batteries and Chargers WarrantyEnglish120Batteries and Chargers WarrantyThe Workmanship Warranty The workmanship warranty guarantees against defects in workmanship under normal use and service.The Capacity WarrantyThe capacity warranty guarantees 80% of the rated capacity for the warranty duration.All MOTOTRBO Batteries Two (2) YearsIMPRES Chargers (Single-Unit and Multi-Unit, Non-Display) Two (2) YearsIMPRES Chargers (Multi-Unit with Display) One (1) YearMOTOTRBO CSA/IECEx/ATEX Lithium-Ion IMPRES Batteries 18 MonthsIMPRES Batteries, When Used Exclusively with IMPRES Chargers 18 Months
Limited WarrantyEnglish121Limited WarrantyMOTOROLA COMMUNICATION PRODUCTSI. WHAT THIS WARRANTY COVERS AND FOR HOW LONG:MOTOROLA SOLUTIONS, INC. (“MOTOROLA”) warrants the MOTOROLA manufactured Communication Products listed below (“Product”) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below:MOTOROLA, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it (with a new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided it is returned in accordance with the terms of this warranty. Replaced parts or boards are warranted for the balance of the original applicable warranty period. All replaced parts of Product shall become the property of MOTOROLA.This express limited warranty is extended by MOTOROLA to the original end user purchaser only and is not assignable or transferable to any other party. This is the complete warranty for the Product manufactured by MOTOROLA. MOTOROLA assumes no obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of MOTOROLA. Unless made in a separate agreement between MOTOROLA and the original end user purchaser, MOTOROLA does not warrant the installation, maintenance or service of the Product.MOTOROLA cannot be responsible in any way for any ancillary equipment not furnished by MOTOROLA which is attached to or used in connection with the Product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use the Product is unique, MOTOROLA disclaims liability for range, coverage, or operation of the system as a whole under this warranty.II. GENERAL PROVISIONS:This warranty sets forth the full extent of MOTOROLA'S responsibilities regarding the Product. Repair, replacement or refund of the purchase price, at MOTOROLA’s option, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR XPR Series Digital Portable Radios Two (2) YearsProduct Accessories (Excluding Batteries and Chargers) One (1) Year
Limited WarrantyEnglish122INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW.III. STATE LAW RIGHTS:SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY. This warranty gives specific legal rights, and there may be other rights which may vary from state to state.IV. HOW TO GET WARRANTY SERVICE:You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to receive warranty service and, also, deliver or send the Product item, transportation and insurance prepaid, to an authorized warranty service location. Warranty service will be provided by MOTOROLA through one of its authorized warranty service locations. If you first contact the company which sold you the Product (e.g., dealer or communication service provider), it can facilitate your obtaining warranty service. You can also call MOTOROLA at 1-800-927-2744 US/Canada.V. WHAT THIS WARRANTY DOES NOT COVER:A) Defects or damage resulting from use of the Product in other than its normal and customary manner.B) Defects or damage from misuse, accident, water, or neglect.C)Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment.D)Breakage or damage to antennas unless caused directly by defects in material workmanship.E) A Product subjected to unauthorized Product modifications, disassembles or repairs (including, without limitation, the addition to the Product of non-MOTOROLA supplied equipment) which adversely affect performance of the Product or interfere with MOTOROLA's normal warranty inspection and testing of the Product to verify any warranty claim.F) Product which has had the serial number removed or made illegible.G)Rechargeable batteries if:(1) any of the seals on the battery enclosure of cells are broken or show evidence of tampering.(2) the damage or defect is caused by charging or using the battery in equipment or service other than the Product for which it is specified.H)Freight costs to the repair depot.I) A Product which, due to illegal or unauthorized alteration of the software/firmware in the Product, does not function in accordance with MOTOROLA’s published specifications or the FCC certification labeling in effect for the Product at the time the Product was initially distributed from MOTOROLA.J) Scratches or other cosmetic damage to Product surfaces that does not affect the operation of the Product.K) Normal and customary wear and tear.
Limited WarrantyEnglish123VI. PATENT AND SOFTWARE PROVISIONS:MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA will pay those costs and damages finally awarded against the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following:A) that MOTOROLA will be notified promptly in writing by such purchaser of any notice of such claim;B) that MOTOROLA will have sole control of the defense of such suit and all negotiations for its settlement or compromise; andC)should the Product or parts become, or in MOTOROLA’s opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit MOTOROLA, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA.MOTOROLA will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary equipment or software not furnished by MOTOROLA which is attached to or used in connection with the Product. The foregoing states the entire liability of MOTOROLA with respect to infringement of patents by the Product or any parts thereof.Laws in the United States and other countries preserve for MOTOROLA certain exclusive rights for copyrighted MOTOROLA software such as the exclusive rights to reproduce in copies and distribute copies of such MOTOROLA software. MOTOROLA software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used to produce any derivative thereof. No other use including, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of such MOTOROLA software or exercise of rights in such MOTOROLA software is permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA patent rights or copyrights.VII. GOVERNING LAW:This Warranty is governed by the laws of the State of Illinois, U.S.A.
NotesEnglish124Notes
Motorola Solutions, Inc.1303 East Algonquin RoadSchaumburg, Illinois 60196 U.S.A.MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license.All other trademarks are the property of their respective owners. © 2013 Motorola Solutions, Inc. All rights reserved.January 2013.www.motorolasolutions.com/mototrbo*68009585001*68009585001-A

Navigation menu