Motorola Solutions 99FT3049 CM200/CM300 VHF Mobile Radio User Manual 2966C25 O cvr

Motorola Solutions, Inc. CM200/CM300 VHF Mobile Radio 2966C25 O cvr

Exhibit 08c Mobile Installation Manual

Radius CM200™/CM300™& PM400™Commercial SeriesTwo-Way Radio Installation GuideMOTOROLA, the Stylized M Logo, and Radius are registered in the US Patent & Trademark Office.All other product or service names are the property of their respective owners. © 2002, 2003 Motorola, Inc. All rights reserved. Printed in U.S.A.*6802966C25*68P02966C25-A
iTable of ContentsInstallation Requirements for Compliance with RadioFrequency (RF) Energy Exposure Safety Standards ............iiiInformation for Vehicles with Electronic Anti-Lock/Anti-Skid Brakes.......................................ivInstallation Warnings .............................................................................................ivInstallation Precautions ..........................................................................................ivBraking System Tests ............................................................................................ivChapter 1 Introduction1.1 General Information ............................................................................................... 11.2 Plan the Installation ............................................................................................... 1Chapter 2 DC Power Cable Installation2.1 Planning the Power Cable Installation ................................................................... 22.2 Power Cable Installation Procedure ...................................................................... 2Chapter 3 Trunnion Installation3.1 Planning the Mounting Trunnion Installation .......................................................... 53.2 Trunnion Installation Procedure ............................................................................. 5Chapter 4 Antenna Installation4.1 Antenna Installation and Compliance with Radio Frequncy(RF) Energy Safety Standards................................................................................ 84.2 Selecting an Antenna Site/Location on a Metal Body Vehicle................................ 84.3 Antenna Installation Procedure .............................................................................. 94.4 Completing the Installation .................................................................................... 9Chapter 5 Installation Options5.1 Mobile Dashboard Mounting ................................................................................ 105.1.1 Installing the Mounting Frame into the Dashboard ................................. 10
ii5.1.2 Inserting the Radio into the Mounting Frame (Figure 5.1)...................... 105.1.3 Removing the Radio from the Mounting Frame ..................................... 115.2 External Speaker Installation ...............................................................................115.3 Visor Microphone Installation ...............................................................................125.3.1 Connecting to the Mobile Radio ............................................................. 12Chapter 6 Accessory Connections6.1 Accessory Connector Pin Functions ....................................................................136.2 Connection Plan for Accessories .........................................................................15Chapter 7 Noise Sources7.1 Introduction ..........................................................................................................167.2 Radiated Noise .....................................................................................................167.3 Conducted Noise ..................................................................................................177.4 Induced Noise ......................................................................................................17Chapter 8 Operation of a Conventional Ignition System8.1 Introduction ..........................................................................................................188.2 Sources of Ignition Interference ...........................................................................18Chapter 9 Detection of Noise Sources9.1 Noise Detection Procedure ..................................................................................209.2 Sources of Noise ..................................................................................................21Chapter 10 Noise Reduction Techniques10.1 General ................................................................................................................2210.2 Ignition System Interference ................................................................................2210.2.1 Engine Maintenance and Tune-Up......................................................... 2210.2.2 Available Noise Reduction Kits .............................................................. 2210.2.3 Ignition Coil Interference ........................................................................ 2310.2.4 Distributor Interference........................................................................... 2310.2.5 Battery Connections............................................................................... 2310.3 Alternator ..............................................................................................................2410.4 Voltage Regulator Noise ......................................................................................2510.5 Hood and Trunk Lid Noise ...................................................................................2510.6 Other Electrical Noises .........................................................................................2510.7 Ground Bonding ...................................................................................................26
Safety-iiiINSTALLATION REQUIREMENTS FOR COMPLIANCE WITH RADIO FREQUENCY (RF) ENERGY EXPOSURE SAFETY STANDARDSATTENTION!This radio is intended for use in occupational/controlled conditions, where users have full knowledge of their exposure and can exercise control over their exposure to meet FCC limits. This radio device is NOT authorized for general population, consumer, or any other use.To ensure compliance to RF Energy Safety standards:• Install only Motorola approved antennas and accessories.• Be sure that antenna installation is per Chapter 4 of this manual.• Be sure that Product Safety and RF Safety Booklet enclosed with this radio is available to the end user upon completion of the installation of this radio.Before using this product, the operator must be familiar with the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with each radio (Motorola Publication part number 68P81095C99) to ensure compliance with Radio Frequency (RF) energy exposure.For a list of Motorola-approved antennas and other accessories, visit the following web site which lists approved accessories for your radio model: http://www.motorola.com/cgiss/index.shtml.
ivInformation for Vehicles with Electronic Anti-Lock/Anti-Skid BrakesThe following installation suggestions and test procedures are recommended for vehicles with electronic anti-lock/anti-skid brakes. Refer to your vehicle service manual for your vehicle’s braking system, or contact your dealer directly.Installation WarningsDisruption of the anti-skid/anti-lock braking system by the radio transmitter may result in unexpected vehicle motion.Motorola recommends the following radio installation precautions and vehicle braking system test procedures to ensure that the radio, when transmitting, does not interfere with the operation of the vehicle braking system.Installation Precautions1. Always provide as much distance as possible between the braking modulator unit and the radio, the radio antenna, and associated transmission line. Before installing the radio, determine the location of the brak-ing modulator unit in the vehicle. Depending on the make and model of the vehicle, the braking modulator unit may be located in the trunk, under the dashboard, in the engine compartment, or in some other cargo area. If you cannot determine the location of the braking modulator unit, refer to the vehicle service man-ual or contact a dealer for the particular make of the vehicle.2. If the braking modular unit is located on the left side of the vehicle, install the radio on the right side of the vehicle, and conversely.3. Route all radio wiring, including the antenna transmission line, as far away as possible from the braking modular unit and associated braking system wiring.4. Never activate the radio transmitter while the vehicle is in motion and the vehicle trunk lid is open.Braking System TestsBe sure the following vehicle testing is done in an isolated area. The following procedure checks for the most common types of interference that may be caused by a radio transmitter to a vehicle braking system:1. Run the vehicle engine at idle speed and set the vehicle transmission selector to PARK. Release the brake pedal completely and key the radio transmitter. While NOT speaking into the microphone, verify that there are no unusual effects (visual or audible) to the vehicle lights, or other electrical equipment and accesso-ries.2. Repeat Step 1, except do so while speaking into the microphone.3. Press the vehicle brake pedal slightly; just enough to illuminate the vehicle brake light(s). Then repeat Steps 1 and 2.4. Press the vehicle brake pedal firmly and repeat Steps 1 and 2.5. Ensure that there is a minimum of two vehicle lengths between the front of the vehicle and any object in the vehicle’s forward path. Then, set the vehicle transmission selector to DRIVE. Press the brake pedal just far enough to stop the vehicle motion completely. Key the radio transmitter. Verify that the vehicle does not start to move while NOT speaking into the microphone.6. Repeat Step 5, except do so while speaking into the microphone.7. Release the brake pedal completely and accelerate the vehicle to a speed between 15 and 25 miles (25 and 40 kilometers) per hour. Ensure that a minimum of two vehicle lengths is maintained between the front of the vehicle and any object in the vehicle’s forward path. Have another person key the radio transmitter, and verify that the vehicle can brake normally to a moderate stop while NOT speaking into the micro-phone.!WARNING
Information for Vehicles with Electronic Anti-Lock/Anti-Skid Brakes v8. Repeat Step 7, except do so while speaking into the microphone.9. Release the brake pedal completely and accelerate the vehicle to a speed of 20 miles (30 kilometers) per hour. Ensure that a minimum of two vehicle lengths is maintained between the front of the vehicle and any object in the vehicle’s forward path. Have another person key the radio transmitter, and verify that the vehi-cle can be braked properly to a sudden (panic) stop while NOT speaking into the microphone.10. Repeat Step 9, except do so while speaking into the microphone.11. Repeat Steps 9 and 10, except use a vehicle speed of 30 miles (50 kilometers) per hour.For radios installed in vehicles fuelled by liquefied petroleum gas, refer to the (U. S.) National Fire Protection Association standard, NFPA 58, for storage, handling, and/or container information.For a copy of the LP-gas standard, NFPA 58, contact the National Fire Protection Association, One Battery Park, Quincy, MA,.!WARNING
vi Information for Vehicles with Electronic Anti-Lock/Anti-Skid
1Chapter 1Introduction1.1 General InformationThere are two methods of installing your mobile radio:1. The standard radio package contains a direct mounting trunnion and power cables.2. CM200/CM300 mobile radios may be mounted in the dashboard of a car using the required DIN Mount Kit FTN6083.An accessory connector on the rear of the radio (see Figure 4-1) enables you to attach different accessories required for the installation.A eight-pin telephone type connector on the front control head panel provides for the connection of various types of microphones.1.2 Plan the Installation1. Mount the radio horizontally near the driver, so the driver can easily view, access, and operate the controls and accessories.2. Ensure that the location is not exposed to dirt and moisture.3. Verify that there will be sufficient space around the mobile unit for air flow and installation.4. Check that there is enough routing space for the power cable connector and the antenna coaxial cable.5. Plan the best place to run connections to minimize chafing, pinching, crushing, and overheating of wires and cables.CAUTION: In a vehicle with an airbag, make sure that the mounting location of the mobile radio, or any radio accessory, is not in the deployment path of the air bag.!
2Chapter 2DC Power Cable Installation2.1 Planning the Power Cable InstallationThe 10 foot (3 m) DC power cable shipped with the radio should be long enough to be installed in most vehicles. Take the following precautions before you begin:• Whenever possible, avoid routing the cable above the catalytic converter. • Use grommets whenever a cable has to pass through a hole in a metal panel. The following table lists power cables available for this radio:2.2 Power Cable Installation ProcedureBegin the power cable installation as follows:1. Determine a routing plan, keeping in mind where the radio is to be mounted.2. Locate an existing hole with grommet in the vehicle fire wall, or use a 3/8-inch (9.5 mm) bit to drill an access hole in the fire wall. Install a grommet with a 3/16-inch (4.9 mm) inside diameter into the hole to protect the power cable.3. From inside the vehicle, feed the red and black leads (without the lugs attached) through the access hole and into the engine compartment. (See Figure 2-1.)CAUTION: This radio must be operated only in negative ground electrical systems. Operating the radio on a positive ground system will cause the cable fuse to short-circuit. Check the vehicle ground polarity before you begin the installation.Table 2-1: Power CablesNumber Description RatingHKN4137_ Low power cable to battery 1-25W; 15A fuse; 14 AWG 3m HKN4191_ High power cable to battery 40-60W; 20A fuse; 12 AWG 3mCAUTION: Improper handling with the power cable may short to ground. Ensure that during radio installation the power cable fuse is removed.CAUTION: Be very careful not to damage existing wires.!!!
DC Power Cable Installation 34. Connect the black lead of the power cable to the nearest vehicle chassis ground point, which is usually the central ground point near the battery (using the provided ring lug if necessary). Shorten the black lead to remove any excess cable. (See Figure 2-2.)5. Place the fuse holder close to the battery. Ensure that it is not near any hot engine component. Mount the fuse holder using its mounting hole and dress the wires as required. 6. Insert the stripped end of the red lead of the fuse holder into the ring lug hole and crimp it. Connect the fuse holder red adapter lead plug to the mating receptacle on the red lead of the power cable. (See Figure 2-2.)7. Connect the power cable black lead directly to the vehicle chassis ground. 8. Connect the red lead ring lug from the fuse holder to the positive (+) battery terminal. Make sure the adapter cable is connected to the main power cable red lead.9. Carefully check that all connections are proper. Insert the fuse into the fuse holder and close the cover. (See Figure 2-2.)Figure 2-1. Power Cable Routing into the Engine CompartmentNOTE Locate a good vehicle ground point. The vehicle central ground point provides the best ground. If this is not available, the vehicle frame provides the best ground. Optimum radio performance can only be achieved with a very low resistance ground connection. Verify that the connections between the battery negative terminal, vehicle chassis, and engine block have low resistance.NOTE Failure to mount the red lead of the power cable kit directly to the battery may result in severe alternator whine interference. Black LeadRed LeadFirewallGrommetEngine CompartmentTo RadioFL08302460
4DC Power Cable InstallationFigure 2-2. Power Cable AssemblyFuseCoverRed LeadRed LeadMountingHoleMolded In-LineFuse HolderTo VehicleChassis GroundEngineCompartment To Battery (+)AdapterFirewallRed LeadBlack LeadRingLugsFL08302470
5Chapter 3Trunnion Installation3.1 Planning the Mounting Trunnion InstallationPlanning is the key to fast, easy radio installation. Before a hole is drilled or a wire is run, inspect the vehicle and determine how and where you intend to mount the antenna, radio, and accessories. If you are using any of the optional accessories, obtain them and plan for their installation using the detailed instructions included with each accessory. Plan wire and cable runs to provide maximum protection from pinching, crushing, and overheating.The mounting trunnion allows the radio to be mounted to a variety of surfaces.1. Ensure the surface can support the weight of the radio.2. Although the mounting trunnion can be mounted to a plastic dashboard, it is recommended that the mounting screws be located so they penetrate the supporting metal frame of the dashboard.3.2 Trunnion Installation Procedure1. Select either the transmission hump or an open underneath portion of the dash to mount your radio. (See Figure 3-1.) When mounting the trunnion on the transmission hump, be careful that the transmission housing is not affected.2. Use the trunnion mounting bracket as a template to mark the hole positions on the mounting surface. Use the innermost three holes for a curved mounting surface, such as the transmission hump, and the four outermost holes for a flat surface such as under the dash.3. Center-punch the spots you marked and use a 5/32-inch (4 mm) bit to drill a hole at each location.4. Secure the trunnion mounting bracket to the mounting surface with the four self-tapping screws provided. (See Figure 3-1.) 5. Attach the radio to the trunnion mounting bracket using two thumbscrews (Figure 3-2.)6. If using a Locking Trunnion, lock the radio into the mounting bracket by closing the locking bracket and locking the cage using the key provided (Figure 3-3.)CAUTION: The locking bracket (RLN4779) is NOT recommended for overhead mounting applications.!
6Trunnion InstallationTabBELOW DASH MOUNTINGMounting SurfaceMountingSurfaceTabThumb Screw(2)TRANSMISSION HUMP MOUNTINGTabThumb Screw(2)Sheet MetalScrewsTrunnion MountingBracketTrunnion Mounting BracketFL0830250O -11.84"(46mm)2.92"(73mm) 2.92"(73mm)1.84"(46mm)1.12"(28mm)Figure 3-1. Transmission Hump Mounting (Top)and Below Dash Mounting (Bottom)
Trunnion Installation 7Figure 3-2. Radio into TrunnionThumb ScrewThumb ScrewTrunnionFL0830329OFigure 3-3. Locking Mounting Bracket (RLN4779)
8Chapter 4Antenna Installation4.1 Antenna Installation and Compliance with Radio Frequency (RF) Energy Safety Standards4.2 Selecting an Antenna Site/Location on a Metal Body Vehicle1. External installation – Check the requirements of the antenna supplier and install the vehicle antenna external to a metal-body vehicle in accordance with those requirements.2. Roof top – For optimum performance and compliance with RF Energy Safety standards, mount the antenna in the center area of the roof.3. Trunk lid – On some vehicles with clearly defined, flat trunk lids, the antennas of some radio models (see restrictions below) can also be mounted on the center area of the trunk lid. For vehicles without clearly defined, flat trunk lids (such as hatchback autos, sport utility vehicles, and pick-up trucks), mount the antenna in the center area of the roof.Before installing an antenna on the trunk lid,• Be sure that the distance from the antenna location on the trunk lid will be at least 85cm (33 inches) from the front surface of the rear seat-back to assure compliance with RF Energy Safety standards• Ensure that the trunk lid is grounded by connecting grounding straps between the trunk lid and the vehicle chassisIF THESE CONDITIONS CANNOT BE SATISFIED, THEN MOUNT THE ANTENNA ON THE ROOF TOP! IMPORTANT NOTE To assure optimum performance and compliance with RF Energy Safety standards, this antenna installation guidelines and instructions are limited to metal-body vehicles with appropriate ground planes and take into account the potential exposure of backseat passengers and bystanders outside the vehicle.NOTE For mobile radios with rated power of 7 watts or less, the only installation restrictions are to use only Motorola approved antennas and install the antenna externally on metal body vehicles. For mobile radios with rated power greater than 7 watts, always adhere to all the guidelines and restrictions in 4.2 below.
Antenna Installation 94. Mounting restrictions for certain radio modelsFor 40 Watt UHF models, the 1/4 wave antenna should be mounted only in the center area of the roof, not on the trunk lid, to assure compliance with RF Energy Safety standards. 5. Ensure that the antenna cable can be easily routed to the radio. Route the antenna cable as far away as possible from any vehicle electronic control units and associated wiring.6. Check the antenna location for any electrical interference.7. Make sure any other mobile radio antenna on this vehicle is at least 30.48cm (1 foot) away from this antenna.4.3 Antenna Installation Procedure1. Mount the antenna according to the instructions provided with the antenna kit. Run the coaxial cable to the radio mounting location. If necessary, cut off the excess cable and install the cable connector.2. Connect the antenna cable connector to the radio antenna connector on the rear of the radio. (See Figure 4-1.)4.4 Completing the Installation1. Mount the microphone clip to a convenient spot near your radio.2. Your microphone has a telephone-type connector at the end of its cord. Plug the microphone into the control head connector.3. To complete your radio installation, plug the power cable into the radio power connector. (See Figure 4-1.)NOTE Any two metal pieces rubbing against each other (such as seat springs, shift levers, trunk and hood lids, exhaust pipes, etc.) in close proximity to the antenna can cause severe receiver interference.Figure 4-1. Connections to the Back of RadioAntennaConnectorConnectorHousingAccessoryConnectorPower Connector
10Chapter 5Installation Options 5.1 Mobile Dashboard Mounting5.1.1 Installing the Mounting Frame into the Dashboard1. Open the radio cut-out in the dashboard to ISO 7736 specification (182mm x 53mm).2. Insert the mounting frame into the dashboard cut-out and retain it by bending back the tabs (using all 6 where possible). Check that the orientation of the frame is correct by ensuring that the word "TOP" is facing upward. 5.1.2 Inserting the Radio into the Mounting Frame (Figure 5.1)1. Make the necessary connections to the radio for power, antenna, and accessory connector as shown in Figure 4-1.2. Plug in all the connectors and push the radio firmly into the mounting frame until the two springs snap into place.NOTE 1. The tabs are easily bent back by twisting a large flat-bladed screwdriver in the slot behind the tabs.2. For a more secure installation, the mounting frame should also be secured with a minimum of one screw.3. The demounting tool can be used as an aid to mounting as well as demounting.TOPFigure 5-1. Fitting the Radio into the FrameDemounting ToolDIN MountFTN6083Fix screws here tosecure frame
Installation Options 115.1.3 Removing the Radio from the Mounting Frame1. Push the two demounting tools through the openings in the mounting frame until the two springs release the radio.2. Slide out the radio.5.2 External Speaker Installation1. Remove the speaker from the trunnion bracket by loosening the two wing screws. 2. Choose a place to mount the speaker.3. Use the trunnion bracket as a template to mark the locations of the three mounting holes.4. Centerpunch and drill a 5/32-inch (4 mm) diameter hole at each location.5. Mount the trunnion bracket with the screws supplied. (See Figure 5-2.)6. Insert the speaker into the trunnion bracket and tighten the two wing screws.7. Insert the external speaker accessory plug into the accessory connector of the radio.NOTE 1. The fixing tabs should be checked for tightness each time the radio is removed. The tabs are easily tightened by twisting a large flat-bladed screwdriver in the slot behind the tabs.2. The mounting frame is not designed for regular mounting and demounting.Figure 5-2. Mounting the Speaker Under the DashboardDashboardFirewallTrunnion BracketToFirewallMountingorDashboardFirewall10-16 x 5/8’’Self-TappingScrew0.157’’ (0.399cm)Diameter TrunnionBracketConsole or FloorFL0830253O
12 Installation Options5.3 Visor Microphone Installation1. Carefully select the installation location for the visor-mounted microphone. Achieve optimum performance of the microphone’s hands-free circuitry by mounting the microphone in one of two locations:• on the sun-visor directly above the driver, or • on the headliner just above the driver. The microphone should never be mounted near the window or in a place where the road and ambient background noise would be substantially high (above 85 dB SPL).5.3.1 Connecting to the Mobile RadioThe visor-mounted microphone cable connects to a 16-pin connector block (part of the hardware supplied): one wire connects to pin 2, and the other wire connects to pin 7 (Figure 5.3).Figure 5-3. 16-Pin Connector Block1215 16FL0830257OViewed from Backside
Accessory Connections 13Chapter 6Accessory Connections6.1 Accessory Connector Pin FunctionsThis section gives a description of the accessory connector pin functions.CAUTION: The accessory connections shown are not compatible to some other models of Motorola radios. Check the appropriate accessory or technical manual for further information.Table 6-1: Connector Pin FunctionsPin Function Description1External Speaker (-) Connect external 8 or 4 Ohm speaker to pins 1 and 16.CAUTION: Bridge-type output. Neither pin 1 nor 16 is Ground.2 External Mic Audio Input impedance: 500 Ohms.80 mV rms at 1 kHz for 60% deviation.This path is enabled when external mic PTT is keyed.3External Mic PTT Put this pin low (less than 0.66 V dc) to key transmitter and enable external mic audio path. This pin is pulled low via a diode when front panel mic PTT is pulled low to allow sensing of mic PTT by accessory. This pin is pulled high to 3.3 V dc via 3.3 k Ohms.4 Programmable Output Defaults to External Alarm. Provides an active high to 13.8 V dc battery supply. Maxi-mum current: 0.25 amps. 5Flat_TX_Audio Input Input impedance: Greater than 35 k Ohms. The nominal input level is 150 mV rms for 60% deviation.6 SCI Serial Communication Interface (for configuration of this pin as General Purpose Input, in addition to pins 8, 12, and 14, return the radio to an authorized service center).7Ground Used as ground.8 Programmable I/O Input or output.9Emergency Input When connecting the Emergency Footswitch between pin 9 and pin 7, the radio will sense the connection upon Power Up. Shorting this pin to Ground by pressing the switch when the radio is OFF, turns ON the radio in Emergency Mode.Shorting this pin to Ground by pressing the switch when the radio is ON, activates Emergency Mode.To turn OFF a radio that was turned ON by the Emergency Footswitch (ON/OFF knob in the OFF position) turn the knob to the ON position and then to the OFF position.10 Ignition Sense For optional 3-wire ignition control, connect this pin to the vehicle ignition-controlled voltage source for ignition-controlled radio ON/OFF.To resume NON ignition state, remove the battery connection for 10 seconds; remove the ignition connection from this pin and reconnect the battery connection.!
14 Accessory Connections11 Receiver Audio Output Programmable (using CPS in the Rx Audio Type): 660 mV rms (de-emphasized/muted) or 330 mV rms (non-de-emphasized/unmuted) at 60% deviation at 1 kHz. Default is de-emphasized/ muted. Minimum load resistance: 5 k Ohms..12 Programmable I/O Input or output.13 Switched B+ (Switched Battery Voltage) 13.8 Vdc (500 mA max.) when radio is ON.14 Programmable I/O Input or output.15 Internal Speaker Connected to internal speaker (+) and by internal jumper to pin 16.16 External Speaker (+) Connect external 8 or 4 Ohm speaker to pins 1 and 16.CAUTION: Bridge-type output. Neither pin 1 nor 16 is Ground.Table 6-1: Connector Pin FunctionsPin Function Description
Accessory Connections 156.2 Connection Plan for Accessories1. Plug the lead with the crimped-on terminal into the #4 socket of the accessory plug. (See Figure 6-1a).2. Screw the circular terminal into the vehicle chassis.3. Make all remaining wiring connections per wiring diagram. (See Figure 6-1b).CAUTION: Do Not short pin 1, 13, or 16 on the accessory connector to Ground; this may damage the radio.Figure 6-2. Accessory Connector!To VehicleChassis(Blk)MAEPF-22954-O#1#2#16 #4#15J3-4Red/WhtBlkExternal AlarmOn-Off SwitchRelay(Bottom View)Alarm Device(Horn or Lights) Horn Relay Contactsor Light Switch To VehicleBatteryExisting Vehicle WiringExternal Alarm Relay KitMAEPF-23082-AFigure 6-1. HLN9328 External Alarm Configurationa. accessory plug b. wiring diagram.AntennaConnectorConnectorHousingAccessoryConnectorPower Connector
16Chapter 7Noise Sources7.1 IntroductionElectrical noise generated by the electrical system of a vehicle, as well as local ambient noise, can interfere with normal operation of mobile radios. Satisfactory operation of a mobile radio may require slight or heavy noise reduction, depending upon the relative strength of the radio signal, and upon the ability of the radio to reject undesired noise. These requirements vary from one vehicle to another, depending upon the vehicle type and required coverage area. When operating in a strong signal area, a certain amount of noise interference can be tolerated. In weak signal areas, however, noise reduction becomes very important. As a rule of thumb, noise levels create greatest interference in the 25-50 MHz band and reduce with increasing frequency.Before attempting any noise reduction procedures, determine the noise source(s). Then, follow a logical, systematic method of elimination until the interference is eliminated or reduced to an acceptable level.Care and patience must be exercised in locating and eliminating noise sources. There may be several sources of noise, each slightly stronger or weaker than the other. Elimination of one source may seem ineffective because another noise source remains active at a barely discernible difference in level. Consult a service manual for the vehicle to determine what noise reduction provisions the manufacturer applies when AM, AM/FM, or CB radios are installed as original equipment. These radios are also subject to electrical noise interference, and the manufacturer may install noise suppression components only upon those vehicles which require radio equipment at the time of manufacture. These noise suppression components should be added in any first attempt to suppress noise.The three major noise sources affecting mobile radio systems are: (1) radiated noise, (2) conducted noise, and (3) induced noise. (See Figure 7-1 for typical vehicular noise sources.)7.2 Radiated NoiseRadiated noise enters the radio through the antenna along with the desired signal and can block or degrade desired communication. It can be generated by power lines, fluorescent lights, or by electrical discharges from static build-up, ignition systems, or electrical motors. Radiated noise is the most common cause of mobile radio interference.When a spark discharge or arc takes place through air, energy is radiated at frequencies from a few kilohertz to hundreds of megahertz. This spurious radiation may have some energy radiated at a frequency near or even identical to the desired radio signal. The standard receiver may be unable to distinguish between the two signals (desired and noise). Therefore they both enter the receiver, resulting in degradation of the desired signal.CAUTION: Do not add interference elimination equipment to vehicles equipped with electronic ignition systems before obtaining advice from the vehicle manufacturer. Addition of some noise suppression components may interfere with proper operation of electronic ignition systems and could seriously damage them.!
Noise Sources 17It is impractical to prevent all arcing in the standard vehicle electrical system. In an 8-cylinder engine running at 2,000 RPM, arcing occurs across the spark plugs at a rate of 8,000 sparks per minute or 133 sparks per second. Electrical motors and generators also produce arcs.7.3 Conducted NoiseConducted noise enters the radio through the points where the radio is attached to the vehicle’s electrical system such as battery cables, ignition switch, chassis ground etc. It can be generated by electrical transients, electrical motors, poor grounding points, or inadequate electrical system filtering (from alternators, generators, voltage regulators, or weak batteries). Conducted noise can degrade both transmit and receive performance of a mobile radio.7.4 Induced NoiseInduced noise enters the radio through the proximity of radio wiring to other wiring in the vehicle. Electrical currents through the standard vehicular wiring can induce undesirable noise signals into the radio cabling. Communication is degraded simply because the wiring provides a transformer-type coupling action without any actual physical connection. Induced noise can degrade both transmit and receive performance of a mobile radio.Figure 7-1. Noise SourcesSpark PlugsIdle StopSolenoidFL0830260-OSpark PlugWiresAlternator orGeneratorVoltageRegulator Distributor IgnitionCoilWheel StaticElectric Fuel PumpAntenna Groundor LocationRadiated Noise Pick-upInadequate Terminalor Fuse Block Filtering Windshield Wiper MotorHeater Air Conditioner BlowerElectric Windows MotorsHood StaticPower Seat Motor
18Chapter 8Operation of a Conventional Ignition System8.1 IntroductionTo effectively reduce ignition interference in a vehicle, it is necessary to understand the operation of an automobile ignition system.Ignition is necessary in a gasoline engine to ignite the gasoline vapor and the air mixture in its cylinders. The system is made up of the battery, distributor, breaker points, coil, condenser, and spark plugs. The battery is the only electrical source of power in an automobile, so the lower battery voltage must be stepped up to the high voltage necessary to arc across the spark plug electrodes. This arc ignites the gas mixture.8.2 Sources of Ignition Interference In the conventional ignition system (Figure 8-1) a mechanical circuit breaker (the cam and points in the distributor) opens the primary circuit of the ignition coil, and high voltage is developed at the secondary. This high voltage is synchronized and applied to each spark plug by the distributor.Figure 8-1. Typical Vehicular Ignition System, Simplified Schematic Diagram HV LeadDistributorSpark plug leadsSparkPlugsIgnitionCoilCondenserCamBreakerPointsIgnitionSwitchBatteryIgnitionCoilCondenserStrayCapacitanceCamBreakerPointsIgnitionSwitchBatteryRotor GapLead InductanceSpark Plug GapFL0830261-O
Operation of a Conventional Ignition System 19The battery is connected to the primary winding of the coil through the ignition switch. The primary circuit is returned to the battery through the breaker points, which are bypassed by the condenser. The points are normally closed. As the cam shaft is rotated by the engine, it’s lobes or corners open and close the points in proper synchronization with the piston in each cylinder.With the ignition switch on and the breaker points closed, coil primary current builds up at a rate determined by the coil inductance.When the breaker points open, primary current decreases and, by self-induction, an electromotive force is induced in the primary which is many times greater than the battery voltage. The high voltage inducted in the coil secondary causes a spark across the distributor rotor-to-spark plug wire gap and then across the spark plug gap for a short interval of time when the breaker points open. The condenser reduces arcing of the points.The secondary circuit of the ignition coil, including the distributor rotor gap and the spark gap, is the main source of ignition interference. The lead inductance and stray capacitance provide a tuned circuit. Because the discharge of the circuit is through a low resistance (ionized spark gap), the circuit tends to oscillate. The frequency and amplitude of oscillation vary as current changes in the spark gap.
20Chapter 9Detection of Noise Sources9.1 Noise Detection ProcedureDetection of offending noise sources is the heart of noise suppression because, after the noise source is identified, the solution becomes obvious. A logical step-by-step procedure is basic to effective noise suppression.Use your available equipment to best advantage. A pick-up loop, about one inch in diameter, can be connected to a portable CB radio or a mobile radio being operated at a frequency similar to the installed radio frequency but from an isolated supply voltage. The pick-up loop can be moved throughout the vehicle with the radio used as a radiated noise detector. Be sure the pick-up loop has sufficient insulation to prevent the input of the radio from coming into direct contact with high voltage points in the vehicle ignition system.A non-polarized bypass capacitor, which has alligator clips firmly attached, can be used on a trial-and-error basis to locate wiring which needs additional filtering. Keep capacitor lead lengths short for best suppression. Ceramic disc capacitors are not as suitable or effective as automotive coaxial capacitors. (See Figure 9-1for part numbers.)Figure 9-1. RLN5277 Noise Reduction Kit for Alternator-Equipped VehiclesIgnitionSwitchBatteryIgnitionCoilDistributorBreakerPointsResistive Wire(Note 2)ResistorSpark Plugs(Note 2)Notes:1. Noise reduction can only be achieved if components are grounded properly.2. Items not supplied in kit. See auto parts dealer.123FL0830262-O
Detection of Noise Sources 219.2 Sources of NoiseSome interference is due to geographic location. This interference does not need to be eliminated since it is possible for the vehicle to be moved away from the interfering noise source. Noise from power lines, fluorescent lights, and other vehicles (emitting high levels of radiated noise) are examples of noise which depend upon location. Make certain that you are not attempting to suppress noise in a vehicle while it is in a noisy location. If you suspect that your location is noisy, simply turn off everything in the vehicle except the radio and listen to the remaining ambient noise. If the noise level is objectionable, you may have to noise suppress the vehicle during a less noisy time of day or in a different, quieter location.Check the installed radio for conducted and inducted noise by using an unmodulated signal generator to supply a clean RF signal through a coaxial cable directly to the antenna connector on the radio set. This should prevent radiated noise from entering the receiver and masking conducted and induced noise. Make certain that the signal generator is not microphonic and is placed away from the noise of the engine and exhaust. Operate the controls for fans, blowers, power windows, headlamps, turn signals, windshield wipers, and other electrical accessories. Listen for the presence of noise in the received radio signal. This will allow the source of the interference to be determined. Some noise sources cannot be turned on and off at will. These sources will need to be attacked piecemeal on a trial and error basis: alternator whine, voltage regulators, electric fuel pump, and other possible sources. Remember that induced noise can result from radio wiring being too close to other vehicle wiring. This problem is most easily solved by proper cable routing at the time of installation.Radiated noise must be attacked after conducted and induced noise has been satisfactorily suppressed. The vehicle ignition system is usually the primary source of this interference. Antenna placement can be critical in some installations. Remember that static discharge generates static or radiated noise and will probably be generated only when the vehicle is in motion.Since radiated noise interference is most noticeable in weak signal areas, it is suggested that suppression be finalized while listening to a weak “on frequency” signal. (The squelch should be “open” so that even marginal signals can be heard.)
22Chapter 10Noise Reduction Techniques10.1 GeneralThere are three basic ways to suppress noise. The first is the addition of resistance in circuits subject to ringing. This method is used for the ignition coil HV cable, spark plug wires, and spark plugs. The second is to filter noise from low voltage wiring using coaxial bypass capacitors. The third is to control static charge build-up using wipers for movable parts such as automobile hoods and trunk lids, or flexible bonding leads for fixed members. Static in wheels may also be controlled using collector rings. Applications of each of these techniques are discussed below.The vehicle manufacturer’s service manual may also provide noise suppression information which is valuable in any first attempt at noise suppression.10.2 Ignition System Interference10.2.1 Engine Maintenance and Tune-UpThe most important step in reducing ignition noise is ensuring that the engine is in proper tune. Pay particular attention to the following points if the noise interference from the ignition system is severe:1. Be sure the spark plugs distributor points, and condenser are in good condition.2. Be sure ignition timing is properly adjusted.3. Be sure the distributor cap and rotor are in good condition. They should be replaced at least every 30,000 miles.4. Be sure that spark plug wires make good, solid contact at each end and are routed as far as possible from low voltage leads.5. Many late-model automobiles are equipped with a shield over the distributor points. Check to see that this shield is properly positioned and securely attached.10.2.2 Available Noise Reduction KitsMotorola offers one noise reduction kit: Model TLN5277 for alternator-equipped vehicles. This kit is for suppression of noise in the primary and secondary of the ignition coil and for bleeding of static charges on the hood. The TLN5277 also is used to suppress noise from the generator and voltage regulator. Figure 9-1, on page 20 illustrates the kit’s usage.Most auto parts dealers can supply 0.05 µF bypass capacitors (condensers), resistive ignition wires, and resistor spark plugs. The type of spark suppression used in noise reduction should always be in accordance with the recommendations of the vehicle manufacturer, that is, if spark plugs are to be replaced with built-in suppressor types, they should be in the proper heat ranges and thread sizes for the particular engine. In each ignition system, there is a maximum amount of resistance that may be connected between the distributor and a spark plug. If resistance-type ignition wire is used, the length of each wire must be limited so that its resistance does not exceed the allowable maximum.
Noise Reduction Techniques 2310.2.3 Ignition Coil InterferenceThis type of interference is characterized by a popping sound which is most noticeable when the engine is running slowly. To suppress the noise, connect a 0.1 µF coaxial capacitor (Motorola Part No. 0882571B02) from the battery side of the ignition coil to vehicle ground (see Figure Figure 10-1). This keeps the distributor noise from being conducted through the battery lead into the electrical system of the vehicle. Note that some electronic ignition systems do not route the battery lead to the ignition coil; proper operation of the ignition system can be impaired if the ”input” terminal is bypassed.10.2.4 Distributor InterferenceThis type of interference is characterized by popping sounds which are present at all engine speeds. It is caused by sparking between the rotor and the distributor cap inserts as the rotor turns. To suppress this noise, use resistance ignition wire to connect the ignition coil to the distributor cap.10.2.5 Battery ConnectionsThe radio set power cable can pick up noise generated in the vehicle. This can be minimized by connecting the power cable directly to the battery instead of the fuse block. The battery acts like a large capacitor (about one Farad for a 50 amp/hour battery), which bypasses induced noise. The battery ground lead should be securely bonded to the vehicle frame. Undesirable parallel ground currents can be minimized by using the vehicle frame as a common ground point. If ignition switch control of the radio is desired, the radio power leads may be connected to the battery through a relay which is controlled by the ignition switch.Figure 10-1. Ignition Coil Noise SuppressionStep 3.Connect wire lead to capacitorusing lockwasher and nut.Step 1.Mount Capacitor(0.1 F Coaxial Type)to vehicle chassisusing lockwasherand self-tapping screw.Step 2.Disconnect wire (dashed)from battery post andconnect to capacitor usinglockwasher and nut.Step 4.Connect capacitorlead to battery post. From distributorDistributor PostBattery PostFL0830264-O
24 Noise Reduction Techniques10.3 AlternatorThis type of interference is characterized by a high-pitched whine which varies with engine speed. A 0.5 µF coaxial capacitor (Motorola Part No. 0882571B01) can be used to bypass the whine. For generators, the capacitors is connected in the armature lead. Never use a capacitor in the field lead. Use the field suppressor assembly supplied in the TLN5277 Noise Reduction Kit. For alternators, the capacitor is connected in the lead to the battery post (see Figures 10-2 and 10-3).Figure 10-2. Generator Whine SuppressionFigure 10-3. Alternator Whine SuppressionStep 1.Mount Capacitor(0.5 F Coaxial Type)under generator ground screw.Step 3.Connect wire lead to capacitorusing lockwasher and nut.Step 4.Connect capacitorlead to armature post.Caution:Do not connectcapacitor to field teminal.Step 2.Disconnect wire (dashed)from armature post and connect to capacitor usinglockwasher and nut.FL0830310-OStep 1.Mount Capacitor to(0.5 F Coaxial Type)under alternatorground screw. Step 2.Disconnect wire frombattery post and connectto capacitor usinglockwasher and nut.Step 3.Connect wire lead to capacitorusing lockwasher and nut.Step 4.Connect capacitorlead to battery post.Caution:Do not connect capacitor to field terminal.FL0830311-O
Noise Reduction Techniques 2510.4 Voltage Regulator NoiseThis type of interference is characterized by erratic popping noises which change only slightly with changes in engine speed. The noise is generated by arcing in the vibrating breaker contacts of the voltage regulator. It can be suppressed by connecting a 0.5 µF coaxial capacitor (Motorola Part No. 0882571B01) in the battery and armature leads of the voltage regulator (see Figure 10-4).10.5 Hood and Trunk Lid NoiseThis type of noise is characterized by irregular popping sounds. It is caused by friction in poorly bonded automobile hoods or trunk lids. This friction causes static electricity to build up until arcing occurs. This type of noise is suppressed using a Motorola Hood Wipers and Mounting Hardware Kit (part of the TLN5277 Noise Reduction Kit) which provides electrical bonding of the hood or trunk to the vehicle body while permitting them to be opened. 10.6 Other Electrical NoisesOther elements of the electrical system which can generate noise are listed below. These can be suppressed by connecting a 0.5 µF bypass capacitor between the noise source and ground.1. Ammeter-to-battery lead 2. Gauges (oil, fuel, temperature)CAUTION: Disconnect the battery ground terminal before attempting to connect components to the voltage regulator.Figure 10-4. Voltage Regulator Noise Suppression!FL0830265-OStep 1.Mount Capacitor(0.5 F Coaxial Type)to vehicle chassisusing lockwasher andself-tapping screw. VehicleStep 2.Disconnect wire (dashed)from battery post andconnect to capacitorusing lockwasher and nut.Step 3.Add lead from batterypost to capacitor using lockwasher and nut.ArmatureA coaxial capacitor canbe added here, if required.BatteryPost
26 Noise Reduction Techniques3. Ignition Switch4. Lamp bulbs (headlamps, tail lamps, dome lamps, etc.)5. Accessory wiring (electrical fuel pump, electric windshield wipers, heater fan motor, window openers, etc.)10.7 Ground BondingIf a vehicle is not properly bonded to ground, static charges can increase. This increase can cause noise from electrical arcing. This type of noise is suppressed by bonding the part using one-inch wide ground straps (keep them as short as possible). Some common points where bonding may be helpful are listed below (see Figure 10-5).A. From engine block to the firewall.B. From engine block to vehicle frame at points where the engine is shock-mounted.C. From the battery ground terminal to the vehicle body.D. From top of front wheel “A” frames to chassis, particularly in cases where rubber-mounted members are used.Figure 10-5. Ground BondingBatteryFirewallChassisFenderWellFront Wheel"A" FrameBACDDFL0830266-O
CM200™Commercial SeriesTwo-Way Radio Installation GuideMOTOROLA, the Stylized M Logo, and Radius are registered in the US Patent & Trademark Office.All other product or service names are the property of their respective owners. © 2002 Motorola, Inc. All rights reserved. Printed in U.S.A.*6802966C25*68P02966C25-O

Navigation menu