Motorola Solutions 89FT6014 Gun holster sensor User Manual MN003064A01

Motorola Solutions, Inc. Gun holster sensor MN003064A01

Manual

en   m   Class B Digital DeviceThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired operation.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio or TV technician for help.• Reorient or relocate the receiving antenna.IMPORTANT SAFETY  INFORMATIONRF Energy Exposure and Product Safety ComplianceAttention!This device is restricted to Occupational use only. Before using the device, read the RF Energy Exposure and Product Safety Guide which contains important operating instructions for safe usage and RF energy awareness and control for Compliance with applicable standards and Regulations. Notice to Users (FCC and Industry Canada)This device complies with Part 15 of the FCC rules and RSS 210 of the Industry Canada rules per the following conditions:• This device may not cause harmful interference.• This device must accept any interfer-ence received, including interference that may cause undesired operation.• Changes or modifications made to this device, not expressly approved by Motorola, could void the authority of the user to operate this equipment.CONSIGNES DE SÉCURITÉ IMPORTANTESExpositionaux radio fréquences et sécu-rité du produitAttention!Cette capteur ne doit être utilisée qu'à des finsprofessionnelles. Avant d'utiliser la radio, lisez leguide Radios bidirectionnelles portatives  : expositionaux radiofréquences et sécurité du produit, quicontient d'importantes instructions de fonctionnementpour une utilisation sécuritaire et des informations surl'exposition aux fréquences radioélectriques, dans lebut d’assurer votre conformité aux normes etrèglements en vigueur.Avis aux utilisateurs (FCC et Industrie Canada)Cet appareil est conforme à la Partie 15 des règlements de la FCC et RSS 210 du règlement d'Industrie Canada selon les conditions énumérée sci-dessous:• Ce dispositif ne doit pas causer d'inter-férences nuisibles.• Cet appareil doit accepter toute inter-férence reçue, y compris les inter-férences qui peuvent perturber le fonctionnement.• Les changements ou les modifications apportées à ce dispositif, non expressément approuvées par.Battery Information:The sensor is using coin cell CR2450. It is recommended to use Panasonic brand.Note: The coin cell is a user replaceable part.Important Information:Battery life may temporarily shorten in  low-temperature conditions. INTRODUCTIONPMLN7593 and PMLN7594 gun holster sensor detects a hand-gun when the hand-gun is removed from or inserted into the holster. An event is sent to the device, and then over the network to applications.PMLN7593 is applied to the Right-handed gun holster, while PMLN7594 is applied to the Left-handed gun holster.Figure 1: The gun holster sensor in isometric viewCOMPATIBLE GUN HOLSTER MODELBelow is the list of weapon types that are supported by Safariland 6280 and 6360 models:• Sig Sauer P226 9 mm• Sig Sauer P226.40• Smith & Wesson M&P 9 mm• Smith & Wesson M&P.40• Glock 17• Glock 19• Glock 21• Glock 22• Glock 34PAIRING AND CONNECTION METHOD1. Press the side button for three seconds. Blue LED blinks, which indicates the sensor is discoverable.2. On your device, select the sensor from the list:  e.g. G_yyy_<last four digit from the MAC address>.3. The sensor is connected to the device.• Blue LED is steady ON for three sec-onds upon connection.OPERATING INSTRUCTIONSThe sensor can be connected to one device at a time. Installing the Sensor1. Unscrew the battery tray.2. Insert the cell into the tray.3. Screw the battery tray.4. Attach the sensor within the gun holster.Figure 2: PMLN7594 (Left) and PMLN7593 (Right)Mounting the Sensor within Holster and Belt Bracket1. Arrange the components as in Figure 3 with the sensor within the holster and belt bracket by facing the M-logo to Belt Bracket.2. Screw the belt loop plate to the holster with the sensor in between.Figure 3: Mounting the sensor within holster and belt bracketCALIBRATIONThe sensor will need to be calibrated when using it for the first time. Red LED will be turned ON when the sensor is NOT calibrated. Withdraw and holster the gun to perform calibration. Each withdraw and holster action interval should be approximately five seconds or more. Repeat the process until the red LED is turned OFF. It may take approximately three times for successful calibration. 3.SOFTWARE UPGRADE1. Red and Blue LED blink alternately during the sensor software update.OTHER FUNCTIONS1. Reset: Disconnect Bluetooth. Press the side button for more than 15 seconds to reset the sensor. This will clear the previous pairing data and calibration data on the sensor as well.2. Still Alive Indicator: Press the side button to check the sensor status. Blue LED indicates the unit is responsive and good. If there is no Blue LED, either the battery is drained or the unit is faulty. NOTESCoin CellCR2450Battery Tray6IPTORXScrew Battery ‘+’Face UpGun Holster SensorScrew HolsterBelt BracketGun HolsterGun Holster Sensor PMLN7593 / PMLN7594*MN003064A01*MN003064A01-ABMOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners.  © 2016 Motorola Solutions, Inc.  All rights reserved. Printed in Side ButtonBattery TrayMAC AddressLEDMN003064A01.fm  Page 1  Wednesday, August 10, 2016  10:55 AM

Navigation menu