Motorola Solutions 89FT3833 Portable 2-Way Radio User Manual MOTOTRBO User Guide

Motorola Solutions, Inc. Portable 2-Way Radio MOTOTRBO User Guide

Contents

Manual

MMOTOTRBO XPRTM 7150Non-Display PortableUser Guide68009677001-ANAG-LACR.book Page i Tuesday, March 12, 2013 3:37 PMdraft
NAG-LACR.book Page ii Tuesday, March 12, 2013 3:37 PMdraft
Declaration of ConformityEnglishiDeclaration of ConformityThis declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below.DECLARATION OF CONFORMITYPer FCC CFR 47 Part 2 Section 2.1077(a)Responsible Party Name: Motorola Solutions, Inc.Address: 1303 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A.Phone Number: 1-800-927-2744Hereby declares that the product:Model Name: XPR 7150 conforms to the following regulations:FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a)Class B Digital DeviceAs a personal computer peripheral, this device complies with Part 15 of the FCC Rules. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.NAG-LACR.book Page i Tuesday, March 12, 2013 3:37 PMdraft
Declaration of ConformityEnglishiiNote: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.NAG-LACR.book Page ii Tuesday, March 12, 2013 3:37 PMdraft
ContentsEnglishiiiContentsThis User Guide contains all the information you need to use the MOTOTRBO XPR 7150 Digital Portable Radio.Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . iImportant Safety Information . . . . . . . . . . . . . . . . . viProduct Safety and RF Exposure Compliance . . .viFirmware Version . . . . . . . . . . . . . . . . . . . . . . . . . . . viComputer Software Copyrights . . . . . . . . . . . . . . . viiHandling Precautions . . . . . . . . . . . . . . . . . . . . . . viiiGetting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . 1What Your Dealer/System Administrator Can Tell You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Preparing Your Radio for Use . . . . . . . . . . . . . . . . . . 2Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 2Attaching the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 3Attaching the Antenna . . . . . . . . . . . . . . . . . . . . . . . . 3Attaching the Universal Connector Cover (Dust Cover) 4 Attaching the Accessory Connector . . . . . . . . . . . . . 4Powering Up the Radio . . . . . . . . . . . . . . . . . . . . . . . 5Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . 5Identifying Radio Controls . . . . . . . . . . . . . . . . . . . . 6Radio Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Programmable Buttons . . . . . . . . . . . . . . . . . . . . . . . 8Assignable Radio Functions . . . . . . . . . . . . . . . . . 8Assignable Settings or Utility Functions . . . . . . . . . 9Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . . . . 9Switching Between Conventional Analog and Digital Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10IP Site Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Capacity Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Linked Capacity Plus . . . . . . . . . . . . . . . . . . . . . . . 12Identifying Status Indicators . . . . . . . . . . . . . . . . . . 15LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Audio Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Indicator Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Receiving and Making Calls . . . . . . . . . . . . . . . . . . 18Selecting a Channel . . . . . . . . . . . . . . . . . . . . . . . . 18Receiving and Responding to a Radio Call . . . . . . 19Receiving and Responding to a Group Call . . . . . 19Receiving and Responding to a Private Call . . . 20Receiving an All Call . . . . . . . . . . . . . . . . . . . . . . 21Receiving and Responding to a Phone Call . . . . 22Phone Call as a Private Call or Group Call . . . 22Phone Call as an All Call . . . . . . . . . . . . . . . . . 22NAG-LACR.book Page iii Tuesday, March 12, 2013 3:37 PMdraft
ContentsEnglishivMaking a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . 23Making a Call with the Channel Selector Knob . . 23Making a Group Call . . . . . . . . . . . . . . . . . . . . 23Making a Private Call . . . . . . . . . . . . . . . . . . . 24 Making a Selective Call . . . . . . . . . . . . . . . . . . . 25Making an All Call . . . . . . . . . . . . . . . . . . . . . . 25Making a Phone Call with the Programmable Phone Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Stopping a Radio Call . . . . . . . . . . . . . . . . . . . . . . 26Talkaround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Monitoring Features . . . . . . . . . . . . . . . . . . . . . . . . 27Monitoring a Channel . . . . . . . . . . . . . . . . . . . . . 27Permanent Monitor . . . . . . . . . . . . . . . . . . . . . . . 28Advanced Features . . . . . . . . . . . . . . . . . . . . . . . . . 29Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Starting and Stopping Scan . . . . . . . . . . . . . . . . 30Responding to a Transmission During a Scan . . 30Deleting a Nuisance Channel . . . . . . . . . . . . . . . 31Restoring a Nuisance Channel . . . . . . . . . . . . . . 31 Vote Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Call Indicator Settings . . . . . . . . . . . . . . . . . . . . . . 32Escalating Alarm Tone Volume . . . . . . . . . . . . . . 32Call Alert Operation . . . . . . . . . . . . . . . . . . . . . . . . 32Receiving and Responding to a Call Alert . . . . . 32Making a Call Alert with the One Touch Access Button 32Emergency Operation . . . . . . . . . . . . . . . . . . . . . . 33Sending an Emergency Alarm . . . . . . . . . . . . . . 33Sending an Emergency Alarm with Call . . . . . . . 34Sending an Emergency Alarm with Voice to Follow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Reinitiating an Emergency Mode . . . . . . . . . . . . 36Exiting an Emergency Mode . . . . . . . . . . . . . . . . 36Privacy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Multi-Site Controls . . . . . . . . . . . . . . . . . . . . . . . . . 37Starting an Automatic Site Search . . . . . . . . . . . 37Stopping an Automatic Site Search . . . . . . . . . . 37Starting a Manual Site Search . . . . . . . . . . . . . . 38Lone Worker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Password Lock Features . . . . . . . . . . . . . . . . . . . . 38Accessing the Radio from Password . . . . . . . . . 38Unlocking the Radio from Locked State . . . . . . . 39Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Finding and Connecting to a Bluetooth Device . . 40Disconnecting from a Bluetooth Device . . . . . . . 41Switching Audio Route . . . . . . . . . . . . . . . . . . . . 41Auto-Range Transponder System (ARTS) . . . . . . . 41Over-the-Air Programming (OTAP) . . . . . . . . . . . . 42Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42NAG-LACR.book Page iv Tuesday, March 12, 2013 3:37 PMdraft
ContentsEnglishvSetting the Squelch Level . . . . . . . . . . . . . . . . . . 42Setting the Power Level . . . . . . . . . . . . . . . . . . . . 42Turning the Voice Operating Transmission (VOX) Feature On or Off . . . . . . . . . . . . . . . . . . . . . . . . . 43Turning the Howling Suppressor Feature On or Off 43Turning Radio Tones/Alerts On or Off . . . . . . . . . 43Checking the Battery Strength . . . . . . . . . . . . . . . 44Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Carry Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Earbuds and Earpieces . . . . . . . . . . . . . . . . . . . . . . 46Headsets and Headset Accessories . . . . . . . . . . . . 47Remote Speaker s . . . . . . . . . . . . . . . . . . . . . . . . . 47Surveillance Accessories . . . . . . . . . . . . . . . . . . . . 48Miscellaneous Accessories . . . . . . . . . . . . . . . . . . . 48Appendix: Maritime Radio Use in the VHF Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Special Channel Assignments . . . . . . . . . . . . . . . . 49Emergency Channel . . . . . . . . . . . . . . . . . . . . . . 49Non-Commercial Call Channel . . . . . . . . . . . . . . 50Operating Frequency Requirements . . . . . . . . . . . . 50Declaration of Compliance for the Use of Distress and Safety Frequencies . . . . . . . . . . . . . . . . . . . . . . . . 52Technical Parameters for Interfacing External Data Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Batteries and Chargers Warranty . . . . . . . . . . . . . . 53Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 54NAG-LACR.book Page v Tuesday, March 12, 2013 3:37 PMdraft
Important Safety InformationEnglishviImportant Safety InformationProduct Safety and RF Exposure ComplianceATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the XPR 7150 SeriesPortable Radio Regulatory Compliance and Product Safety / Quick Reference Guide (Motorola Publication part number 68009511001) to ensure compliance with RF energy exposure limits. For a list of Motorola-approved antennas, batteries, and other accessories, visit the following website: http://www.motorolasolutions.comAny modification to this device, not expressly authorized by Motorola, may void the user’s authority to operate this device.Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.This radio transmitter has been approved by Industry Canada to operate with Motorola-approved antenna with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.Firmware VersionAll the features described in the following sections are supported by the radio's software version R02.06.10. Check with your dealer or system administrator for more details for all the features supported.Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio.NAG-LACR.book Page vi Tuesday, March 12, 2013 3:37 PMdraft
Computer Software CopyrightsEnglishviiComputer Software CopyrightsThe Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, reproduced, modified, reverse-engineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive license to use that arises by operation of law in the sale of a product.The AMBE+2TM voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Communications Equipment. The user of this Technology is explicitly prohibited from attempting to decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. U.S. Pat. Nos. #5,870,405, #5,826,222, #5,754,974, #5,701,390, #5,715,365, #5,649,050, #5,630,011, #5,581,656, #5,517,511, #5,491,772, #5,247,579, #5,226,084 and #5,195,166.NAG-LACR.book Page vii Tuesday, March 12, 2013 3:37 PMdraft
Handling PrecautionsEnglishviiiHandling PrecautionsThe MOTOTRBO XPR 3300 Portable Radio meets IP55 specifications with antenna attached, allowing the radio to withstand adverse field conditions such as being used in rain or dusty environment.•If the radio has been exposed to water or rain, shake the radio well to remove any water that may be trapped inside the speaker grille, port and aesthetic cover (if applicable). Trapped water in speaker grille and port could cause decreased audio performance. If aesthetic cover is attached onto radio, trapped water in aesthetic cover could cause corrosion on the slim connector interface gold contacts.•If the radio’s battery contact area has been exposed to water, clean and dry battery contacts on both the radio and the battery before attaching the battery to the radio. The residual water could short-circuit the radio.•If the radio has been exposed to corrosive substance (e.g.saltwater), rinse the radio and battery in fresh water then dry the radio and battery.•To clean the exterior surfaces of the radio, use a diluted solution of mild dishwashing detergent and fresh water (i.e. one teaspoon of detergent to one gallon of water). •The radio with antenna attached properly is designed to be protected against dust and low pressure jets of water projected with nozzle 6.3mm diameter at flow rate of 12.5 l/min, with water pressure at 30 kN/m2 and from a distance of 2.5m to 3m for at least 3 min. Exceeding either maximum limit or use without antenna may result in damage to the radio.•When cleaning the radio, do not use a high pressure jet spray on the radio as this may cause to leak.Do not disassemble the radio. This could damage radio seals and result in leak paths into the radio. Radio maintenance should only be done in service depot that is equipped to test and replace the seal on the radio.NAG-LACR.book Page viii Tuesday, March 12, 2013 3:37 PMdraft
Getting StartedEnglish1Getting StartedTake a moment to review the following:How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . . . page 1What Your Dealer/System Administrator Can Tell You. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1How to Use This GuideThis User Guide covers the basic operation of the MOTOTRBO Non-Display Portables.However, your dealer or system administrator may have customized your radio for your specific needs. Check with your dealer or system administrator for more information.Throughout this publication, the icons below are used to indicate features supported in either the conventional Analog mode or conventional Digital mode:For features that are available in both Analog and Digital modes, no icon is shown.For features that are available in a conventional multi-site mode, see IP Site Connect on page 10 for more information.Selected features are also available on the single-site trunking mode, Capacity Plus. See Capacity Plus on page 12 for more information.Selected features are also available in the multi-site trunking mode, Linked Capacity Plus. See Linked Capacity Plus on page 12 for more information.What Your Dealer/System Administrator Can Tell YouYou can consult your dealer or system administrator about the following:•Is your radio programmed with any preset conventional channels?•Which buttons have been programmed to access other features? •What optional accessories may suit your needs?•What are the best radio usage practices for effective communication?•What maintenance procedures will help promote longer radio life?Indicates a conventional Analog Mode-Only feature.Indicates a conventional Digital Mode-Only feature.NAG-LACR.book Page 1 Tuesday, March 12, 2013 3:37 PMdraft
Preparing Your Radio for UseEnglish2Preparing Your Radio for UseAssemble your radio by following these steps:Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2Attaching the Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . page 3Attaching the Antenna. . . . . . . . . . . . . . . . . . . . . . . . . . page 3Attaching the Universal Connector Cover (Dust Cover) . . . . . . . . . . . . . . . . . . . . . . . . . . page 4Attaching the Accessory Connector . . . . . . . . . . . . . . . page 4Powering Up the Radio . . . . . . . . . . . . . . . . . . . . . . . . . page 5Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . page 5Charging the BatteryYour radio is powered by a Lithium-Ion (Li-lon) battery. To avoid damage and comply with warranty terms, charge the battery using a Motorola charger exactly as described in the charger user guide. It is recommended your radio remains powered off while charging.Charge a new battery 14 to 16 hours before initial use for best performance.IMPORTANT:ALWAYS charge your IMPRES battery with an IMPRES charger for optimized battery life and valuable battery data. IMPRES batteries charged exclusively with IMPRES chargers receive a 6-month capacity warranty extension over the standard Motorola Premium battery warranty duration.NAG-LACR.book Page 2 Tuesday, March 12, 2013 3:37 PMdraft
Preparing Your Radio for UseEnglish3Attaching the BatteryAlign the battery with the rails on the back of the radio. Fit the battery to the contacts and push the top of the battery down until the latch snaps into place.To remove the battery, turn the radio off. Move the battery latch into unlock position and hold.Attaching the AntennaWith the radio turned off, set the antenna in its receptacle and turn clockwise.To remove the antenna, turn the antenna counterclockwise.Battery LatchIf antenna needs to be replaced, ensure that only MOTOTRBO antennas are used. Neglecting this will damage your radio. See Antennas on page 45 for a list of available antennas.31NAG-LACR.book Page 3 Tuesday, March 12, 2013 3:37 PMdraft
Preparing Your Radio for UseEnglish4Attaching the Universal Connector Cover (Dust Cover)The universal connector is located on the antenna side of the radio. It is used to connect MOTOTRBO accessories to the radio.1Insert the slanted end of the cover into the slots above the universal connector. 2Press downwards on the cover to seat the dust cover properly on the Universal Connector. 3Secure the dust cover to the radio by pushing the latch upwards.To remove the dust cover, push the latch downwards. Lift the cover up and slide down the dust cover from the universal connector to remove it.Replace the dust cover when the universal connector is not in use. Attaching the Accessory ConnectorThe accessory connector is to be secured to the universal connector on the antenna side of he radio.To attach the accessory connector, refer to the steps shown in the diagram.To remove the accessory connector, refer to the steps shown in the diagram.123123123NAG-LACR.book Page 4 Tuesday, March 12, 2013 3:37 PMdraft
Preparing Your Radio for UseEnglish5Powering Up the RadioRotate the On/Off/Volume Control Knob clockwise until you hear a click. The LED lights up solid green.A brief tone sounds, indicating that the power up test is successful.There is no power up tone if the radio tones/alerts function is disabled (see Turning Radio Tones/Alerts On or Off on page 43).If your radio does not power up, check your battery. Make sure that it is charged and properly attached. If your radio still does not power up, contact your dealer.To turn off the radio, rotate this knob counterclockwise until you hear a click.Adjusting the VolumeTo increase the volume, turn the On/Off/Volume Control Knob clockwise.To decrease the volume, turn this knob counterclockwise.Note: Your radio can be programmed to have a minimum volume offset where the volume level cannot be turned down fully. Check with your dealer or system administrator for more information.3131NAG-LACR.book Page 5 Tuesday, March 12, 2013 3:37 PMdraft
Identifying Radio ControlsEnglish6Identifying Radio ControlsTake a moment to review the following:Radio Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7Programmable Buttons . . . . . . . . . . . . . . . . . . . . . . . . . page 8Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . . . . . . page 9Switching Between Conventional Analog andDigital Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 10IP Site Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 10Capacity Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 12Linked Capacity Plus. . . . . . . . . . . . . . . . . . . . . . . . . . page 12NAG-LACR.book Page 6 Tuesday, March 12, 2013 3:37 PMdraft
Identifying Radio ControlsEnglish7Radio ControlsChannel Selector KnobOn/Off/Volume Control KnobLED IndicatorPush-to-Talk (PTT) Button8652141039731111234Side Button 1*Side Button 2*SpeakerUniversal Connector for AccessoriesEmergency ButtonAntenna567891011* These buttons are programmableNAG-LACR.book Page 7 Tuesday, March 12, 2013 3:37 PMdraft
Identifying Radio ControlsEnglish8Programmable ButtonsYour dealer can program the programmable buttons as shortcuts to radio functions or preset channels/groups depending on the duration of a button press:•Short press – Pressing and releasing rapidly.•Long press – Pressing and holding for the programmed duration.•Hold down – Keeping the button pressed.NOTE: The programmed duration of a button press is applicable for all assignable radio/utility functions or settings. See Emergency Operation on page 33 for more information on the programmed duration of the Emergency button.Assignable Radio FunctionsBluetooth® Audio Switch – Toggles audio routing between internal radio speaker and external Bluetooth-enabled accessory. Bluetooth Connect – Initiates a Bluetooth find-and-connect operation. Bluetooth Disconnect – Terminates all existing Bluetooth connections between your radio and any Bluetooth-enabled devices. Bluetooth Discoverable – Enables your radio to enter Bluetooth Discoverable Mode.Call Forwarding – Toggles Call Forwarding on or off.Voice Announcement for Channel – Plays zone and channel announcement voice messages for the current channel. This function is unavailable when Voice Announcement is disabled.Emergency – Depending on the programming, initiates or cancels an emergency alarm or call.Intelligent Audio On/Off – Toggles Intelligent Audio on or off. Manual Site Roam*‡ – Starts the manual site search.Mic AGC On/Off – Toggles the internal automatic gain control (AGC) on or off. Not applicable during a Bluetooth session.Monitor – Monitors a selected channel for activity.Nuisance Channel Delete*‡ – Temporarily removes an unwanted channel, except for the Selected Channel, from the scan list. The Selected Channel refers to the user’s selected zone/channel combination from which scan is initiated.Notifications – Provides direct access to the Notifications List.One Touch Access – Directly initiates a predefined Private or Group Call, a Call Alert.* Not applicable in Capacity Plus‡ Not applicable in Linked Capacity PlusNAG-LACR.book Page 8 Tuesday, March 12, 2013 3:37 PMdraft
Identifying Radio ControlsEnglish9Permanent Monitor*‡– Monitors a selected channel for all radio traffic until function is disabled.Privacy – Toggles privacy on or off.Repeater/Talkaround*‡ – Toggles between using a repeater and communicating directly with another radio.Scan* – Toggles scan on or off. Site Lock On/Off*‡ – Toggles the automatic site roam on or off.Transmit Interrupt Remote Dekey – Stops an ongoing interruptible call to free the channel. (A Software License Key sold separately is required to use this feature).Voice Announcement On/Off – Toggles Voice Announcement on or off. Voice Operating Transmission (VOX) – Toggles VOX on or off.Zone – Allows selection from only one zone.Battery Strength – Indicates battery strength via the LED Indicator.Assignable Settings or Utility FunctionsAll Tones/Alerts – Toggles all tones and alerts on or off.Power Level – Toggles transmit power level between high and low.Squelch – Toggles squelch level between tight and normal.Push-To-Talk (PTT) ButtonThe PTT button on the side of the radio serves two basic purposes:•While a call is in progress, the PTT button allows the radio to transmit to other radios in the call.Press and hold down PTT button to talk. Release the PTT button to listen.The is activated when the PTT button is pressed.* Not applicable in Capacity Plus‡ Not applicable in Linked Capacity Plus31PTT ButtonNAG-LACR.book Page 9 Tuesday, March 12, 2013 3:37 PMdraft
Identifying Radio ControlsEnglish10•While a call is not in progress, the PTT button is used to make a new call (see Making a Radio Call on page 23).Depending on programming, if the Talk Permit Tone or the PTT Sidetone is enabled, wait until the short alert tone ends before talking.During a call, if the Channel Free Indication feature is enabled on your radio (programmed by your dealer), you will hear a short alert tone the moment the target radio (the radio that is receiving your call) releases the PTT button, indicating the channel is free for you to respond.You will also hear a continuous talk prohibit tone, if your call is interrupted, indicating that you should release the PTT button, for example when the radio receives an Emergency Call.Switching Between Conventional Analog and Digital ModeEach channel in your radio can be configured as a conventional analog or conventional digital channel. Use the Channel Selector Knob to switch between an analog or a digital channel.When switching from digital to analog mode, certain features are unavailable.Your radio also has features available in both analog and digital mode. However, the minor differences in the way each feature works does NOT affect the performance of your radio.NOTE: Your radio also switches between digital and analog modes during a dual mode scan (see Scan on page 30).IP Site ConnectThis feature allows your radio to extend conventional communication beyond the reach of a single site, by connecting to different available sites which are connected via an Internet Protocol (IP) network.31Channel Selector Knob NAG-LACR.book Page 10 Tuesday, March 12, 2013 3:37 PMdraft
Identifying Radio ControlsEnglish11NOTE: This feature is not applicable in Capacity Plus.When the radio moves out of range from one site and into the range of another, it connects to the new site's repeater to send or receive calls/data transmissions. Depending on your settings, this is done automatically or manually.If the radio is set to do this automatically, it scans through all available sites when the signal from the current site is weak or when the radio is unable to detect any signal from the current site. It then locks on to the repeater with the strongest Received Signal Strength Indicator (RSSI) value.In a manual site search, the radio searches for the next site in the roam list that is currently in range (but which may not have the strongest signal) and locks on to it.NOTE: Each channel can only have either Scan or Roam enabled, not both at the same time.Channels with this feature enabled can be added to a particular roam list. The radio searches the channel(s) in the Members roam list during the automatic roam operation to locate the best site.A Members roam list supports a maximum of 16 channels (including the Selected Channel).You cannot manually add or delete an entry to the Members roam list. A Software License Key sold separately is required to use this feature. Check with your dealer or system administrator for more information.NAG-LACR.book Page 11 Tuesday, March 12, 2013 3:37 PMdraft
Identifying Radio ControlsEnglish12Capacity PlusCapacity Plus is a single-site trunking configuration of the MOTOTRBO radio system, which uses a pool of channels to support hundreds of users and up to 254 Groups. This feature allows your radio to efficiently utilize the available number of programmed channels while in Repeater Mode.You can only access channel(s) with Capacity Plus via the Channel Selector Knob, while features supported in Capacity Plus can be accessed via a programmable button press.You will hear a negative indicator tone if you access a feature not applicable to Capacity Plus via a programmable button press.Your radio also has features that are available in both conventional digital mode and Capacity Plus. However, the minor differences in the way each feature works does NOT affect the performance of your radio.A Software License Key sold separately is required to use this feature.Check with your dealer or system administrator for more information on this system.Linked Capacity PlusLinked Capacity Plus is a multi-site multi-channel trunking configuration of the MOTOTRBO radio system, combining the best of both Capacity Plus and IP Site Connect configurations.Linked Capacity Plus allows your radio to extend trunking communication beyond the reach of a single site, by connecting to different available sites which are connected via an Internet Protocol (IP) network. It also provides an increase in capacity by efficiently utilizing the combined available number of programmed channels supported by each of the available sites. When the radio moves out of range from one site and into the range of another, it connects to the new site's repeater to send or receive calls/data transmissions. Depending on your settings, this is done automatically or manually.If the radio is set to do this automatically, it scans through all available sites when the signal from the current site is weak or when the radio is unable to detect any signal from the current site. It then locks on to the repeater with the strongest Received Signal Strength Indicator (RSSI) value.In a manual site search, the radio searches for the next site in the roam list that is currently in range (but which may not have the strongest signal) and locks on to it.Any channel with Linked Capacity Plus enabled can be added to a particular roam list. The radio searches these channels during the automatic roam operation to locate the best site.NAG-LACR.book Page 12 Tuesday, March 12, 2013 3:37 PMdraft
Identifying Radio ControlsEnglish13NOTE: You cannot manually add or delete an entry to the roam list. Check with your dealer or system administrator for more information.Similar to Capacity Plus, icons of features not applicable to Linked Capacity Plus are not available in the menu. You hear a negative indicator tone if you try to access a feature not applicable to Linked Capacity Plus via a programmable button press. A Software License Key sold separately is required to use this featureCheck with your dealer or system administrator for more information on this configuration.NAG-LACR.book Page 13 Tuesday, March 12, 2013 3:37 PMdraft
Identifying Radio ControlsEnglish14NAG-LACR.book Page 14 Tuesday, March 12, 2013 3:37 PMdraft
Identifying Status IndicatorsEnglish15Identifying Status IndicatorsYour radio indicates its operational status through the following:LED Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 15Audio Tones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 16Indicator Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 17LED IndicatorThe LED indicator shows the operational status of your radio.Blinking red – Radio is transmitting at low battery condition, receiving an emergency transmission or has failed the self-test upon powering up, or has moved out of range if radio is configured with Auto-Range Transponder System.Solid yellow – Radio is monitoring a conventional channel or in Bluetooth Discoverable Mode. Also indicates fair battery charge when Battery Strength button is pressed.Blinking yellow – Radio is scanning for activity or receiving a Call Alert, or all local Linked Capacity Plus channels are busy.Rapidly blinking yellow – Radio is actively searching for a new site. LED Indicator31NAG-LACR.book Page 15 Tuesday, March 12, 2013 3:37 PMdraft
Identifying Status IndicatorsEnglish16Double blinking yellow – Radio is no longer connected to the repeater while in Capacity Plus or Linked Capacity Plus, all Capacity Plus channels and Linked Capacity Plus channels are currently busy, Auto Roaming is enabled, radio is actively searching for a new site. Also indicates radio has yet to respond to a group call alert, or radio is locked.Solid green – Radio is powering up, or transmitting. Also indicates full charge of the battery when Battery Strength button is pressed.Blinking green – Radio is receiving a non-privacy-enabled call or data, detecting activity or retrieving Over-the-Air Programming transmissions over the air.Double blinking green – Radio is receiving a privacy-enabled call or data. NOTE: While in conventional mode, when the LED blinks green, it indicates the radio detects activity over the air. Due to the nature of the digital protocol, this activity may or may not affect the radio's programmed channel.For Capacity Plus and Linked Capacity Plus, there is no LED indication when the radio is detecting activity over the air.Audio TonesAlert tones provide you with audible indications of the radio’s status or the radio’s response to data received.Continuous Tone A monotone sound. Sounds continuously until termination.Periodic Tone Sounds periodically depending on the duration set by the radio. Tone starts, stops, and repeats itself.Repetitive Tone A single tone that repeats itself until it is terminated by the user.Momentary Tone Sounds only once for a short period of time defined by the radio.NAG-LACR.book Page 16 Tuesday, March 12, 2013 3:37 PMdraft
Identifying Status IndicatorsEnglish17Indicator TonesHigh pitched tone Low pitched tone Positive Indicator ToneNegative Indicator ToneNAG-LACR.book Page 17 Tuesday, March 12, 2013 3:37 PMdraft
Receiving and Making CallsEnglish18Receiving and Making CallsOnce you understand how your MOTOTRBO Portable is configured, you are ready to use your radio.Use this navigation guide to familiarize yourself with the basic Call features:Selecting a Radio Channel, Subscriber ID, or Group ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 18Receiving and Responding to a Radio Call. . . . . . . . . page 19Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . . . page 23Stopping a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . . page 26Talkaround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 27Monitoring Features . . . . . . . . . . . . . . . . . . . . . . . . . . page 27Selecting a ChannelTransmissions are sent and received on a channel. Depending on your radio’s configuration, each channel may have been programmed differently to support different groups of users or supplied with different features. After selecting the relevant Zone, select the relevant channel you require to transmit or receive on.Procedure:Once the required zone is set (if you have multiple zones in your radio), turn the Channel Selector Knob to select the number that represents the channel, subscriber ID, or group ID.31NAG-LACR.book Page 18 Tuesday, March 12, 2013 3:37 PMdraft
Receiving and Making CallsEnglish19Receiving and Responding to a Radio CallOnce the channel, subscriber ID, or group ID is set, you can proceed to receive and respond to calls.The LED lights up solid green while the radio is transmitting and blinks when the radio is receiving.NOTE: The LED lights up solid green while the radio is transmitting and double blinks green when the radio is receiving a privacy-enabled call.To unscramble a privacy-enabled call, your radio must have the same Privacy Key, OR the same Key Value and Key ID (programmed by your dealer) as the transmitting radio (the radio you are receiving the call from). See Privacy on page 36 for more information. Receiving and Responding to a Group CallTo receive a call from a group of users, your radio must be configured as part of that group.1The LED blinks green. Your radio unmutes and the incoming call sounds through the radio's speaker.2To respond, hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.3 If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the transmitting radio releases the PTT button, indicating the channel is free for you to respond.Press the PTT button to respond to the call.OR If the Voice Interrupt feature is enabled, press the PTT button to stop the current call from the transmitting radio and free the channel for you to talk/respond.4The LED lights up solid green. 5Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the .OR31LED IndicatorNAG-LACR.book Page 19 Tuesday, March 12, 2013 3:37 PMdraft
Receiving and Making CallsEnglish20 Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the .6Release the PTT button to listen.7If there is no voice activity for a predetermined period of time, the call ends.See Making a Group Call on page 23 for details on making a Group Call.Receiving and Responding to a Private Call A Private Call is a call from an individual radio to another individual radio.Procedure:When you receive a private call: 1The LED blinks green. Your radio unmutes and the incoming call sounds through the radio's speaker.2To respond, hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.3If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the transmitting radio releases the PTT button, indicating the channel is free for you to respond.Press the PTT button to respond to the call.ORIf the Voice Interrupt feature is enabled, press the PTT button to stop the current call from the transmitting radio and free the channel for you to talk/respond.4Press the PTT button to respond to the call. The LED lights up solid green.5Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the .6Release the PTT button to listen.7If there is no voice activity for a predetermined period of time, the call ends.8You hear a short tone.See Making a Private Call on page 24 for details on making a Private Call.NAG-LACR.book Page 20 Tuesday, March 12, 2013 3:37 PMdraft
Receiving and Making CallsEnglish21 Receiving and Responding to a Selective Call A Selective Call is a call from an individual radio to another individual radio. It is a Private Call on an analog system.Procedure:When you receive a Selective Call: 1The LED blinks green. Your radio unmutes and the incoming call sounds through the radio's speaker.2To respond, hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the transmitting radio releases the PTT button, indicating the channel is free for you to respond.Press the PTT button to respond to the call.4Press the PTT button to respond to the call. The LED lights up solid green.5Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the .6Release the PTT button to listen.7If there is no voice activity for a predetermined period of time, the call ends.8You hear a short tone.See Making a Selective Call on page 25 for details on making a Selective Call. Receiving an All CallAn All Call is a call from an individual radio to every radio on the channel. It is used to make important announcements requiring the user’s full attention.Procedure:When you receive an All Call:1A tone sounds and the LED blinks green. Your radio unmutes and the incoming call sounds through the radio's speaker.2An All Call does not wait for a predetermined period of time before ending. If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the transmitting radio releases the PTT button, indicating the channel is now available for use.You cannot respond to an All Call.NOTE: The radio stops receiving the All Call if you switch to a different channel while receiving the call.During an All Call, you will not be able to use any programmed button functions until the call ends.NAG-LACR.book Page 21 Tuesday, March 12, 2013 3:37 PMdraft
Receiving and Making CallsEnglish22Receiving and Responding to a Phone Call Phone Call as a Private Call or Group CallProcedure:When you receive a Phone Call as a Private Call or Group Call:1The LED blinks green. Your radio unmutes and the incoming call sounds through the radio’s speaker.2To respond, hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3Press the PTT button to talk and release it to listen. 4Press d to end the call.5You hear a short tone.If Phone Call capability is not enabled in your radio, your radio mutes the call. Phone Call as an All CallProcedure:When you receive a Phone Call as an All Call:The LED blinks green. Your radio unmutes and the incoming call sounds through the radio’s speaker.An All Call does not wait for a predetermined period of time before ending.NOTE: When you receive a Phone Call as an All Call, you can respond to the call or end the call, only if an All Call type is assigned to the channel.NAG-LACR.book Page 22 Tuesday, March 12, 2013 3:37 PMdraft
Receiving and Making CallsEnglish23Making a Radio CallYou can select a channel, subscriber ID or group ID by using:•The Channel Selector Knob.•A programmed One Touch Access button. •A programmable button – This method is for Phone Calls only (see Making a Phone Call with the Programmable Phone Button on page 26). NOTE: Your radio must have the Privacy feature enabled on the channel to send a privacy-enabled transmission. Only target radios with the same Privacy Key OR the same Key Value and Key ID as your radio will be able to unscramble the transmission. See Privacy on page 36 for more information. The One Touch Access feature allows you to make a Group or Private Call to a predefined ID easily. This feature can be assigned to a short or long programmable button press.You can ONLY have one ID assigned to a One Touch Access button. Your radio can have multiple One Touch Access buttons programmed.Making a Call with the Channel Selector KnobMaking a Group CallTo make a call to a group of users, your radio must be configured as part of that group.Procedure:1Select the channel with the active group alias or ID. See Selecting a Channel on page 18.ORPress the programmed One Touch Access button.2Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.3Press the PTT button to make the call. The LED lights up solid green.4Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the .OR Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the .5Release the PTT button to listen. When the target radio responds, the LED blinks green.NAG-LACR.book Page 23 Tuesday, March 12, 2013 3:37 PMdraft
Receiving and Making CallsEnglish246If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the target radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond. ORIf there is no voice activity for a predetermined period of time, the call ends.Making a Private Call While you can receive and/or respond to a Private Call initiated by an authorized individual radio, your radio must be programmed for you to initiate a Private Call.There are two types of Private Calls. The first type, where a radio presence check is performed prior to setting up the call, while the other sets up the call immediately. Only one of these call types can be programmed to your radio by your dealer.You hear a negative indicator tone, when you make a Private Call via the One Touch Access button or the Channel Selector Knob, if this feature is not enabled.Use the Call Alert features to contact an individual radio. See Call Alert Operation on page 32 for more information.Procedure:1Select the channel with the active group alias or ID. See Selecting a Channel on page 18.ORPress the programmed One Touch Access button.2Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.3Press the PTT button to make the call. The LED lights up solid green.4Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the .5Release the PTT button to listen. When the target radio responds, the LED blinks green.6If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the target radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond.ORIf there is no voice activity for a predetermined period of time, the call ends.7You hear a short tone.NAG-LACR.book Page 24 Tuesday, March 12, 2013 3:37 PMdraft
Receiving and Making CallsEnglish25 Making a Selective Call Just like a Private Call, while you can receive and/or respond to a Selective Call initiated by an authorized individual radio, your radio must be programmed for you to initiate a Selective Call.Procedure:1Select the channel with the active group alias or ID. See Selecting a Channel on page 18.2Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.3Press the PTT button to make the call. The LED lights up solid green.4Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the .5Release the PTT button to listen. When the target radio responds, the LED blinks green.6If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the target radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond.ORIf there is no voice activity for a predetermined period of time, the call ends.7You hear a short tone.Making an All CallThis feature allows you to transmit to all users on the channel. Your radio must be programmed to allow you to use this feature.Procedure:1Select the channel with the active group alias or ID. See Selecting a Channel on page 18.2Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.3Press the PTT button to make the call. The LED lights up solid green.4Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the .OR Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the .Users on the channel cannot respond to an All Call.NAG-LACR.book Page 25 Tuesday, March 12, 2013 3:37 PMdraft
Receiving and Making CallsEnglish26Making a Phone Call with the Programmable Phone ButtonProcedure:1Press the programmed Phone button.2The LED lights up solid green.3You hear the dialing tone of the telephone user. 4Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.5Press the PTT button to talk and release it to listen. 6If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the target radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond.ORIf there is no voice activity for a predetermined period of time, the call ends.7You hear a short tone.When you press PTT button while in the Phone Contacts screen, a tone sounds.When the telephone user ends the call, a tone sounds.During the call, when you press One Touch Access button with the deaccess code preconfigured, your radio attempts to end the call.Stopping a Radio Call This feature allows you to stop an ongoing Group or Private Call to free the channel for transmission. For example, when a radio experiences a “stuck ” condition where the PTT button is inadvertently pressed by the user.Your radio must be programmed to allow you to use this feature.Procedure:While on the required channel:1Press the programmed Transmit Interrupt Remote Dekey button.2Wait for acknowledgment.3The radio sounds a positive indicator tone, indicating that the channel is now free.ORThe radio sounds a negative indicator tone, indicating that the radio is unable to free the channel.Your radio sounds a negative indicator tone until you release the PTT button, if it is transmitting an interruptible call that is stopped via this feature. NAG-LACR.book Page 26 Tuesday, March 12, 2013 3:37 PMdraft
Receiving and Making CallsEnglish27TalkaroundYou can continue to communicate when your repeater is not operating, or when your radio is out of the repeater’s range but within talking range of other radios. This is called “talkaround”.NOTE: This feature is not applicable in Capacity Plus and Linked Capacity Plus.Procedure: 1Press the programmed Repeater/Talkaround button.2You hear a positive indicator tone, indicating the radio is in Talkaround mode.ORYou hear a negative indicator tone, indicating the radio is in Repeater mode.The Talkaround setting is retained even after powering down.Monitoring FeaturesMonitoring a ChannelUse the Monitor feature to make sure a channel is free before transmitting.NOTE: This feature is not applicable in Capacity Plus and Linked Capacity Plus.Procedure:1Press and hold the programmed Monitor button and listen for activity.2You hear radio activity or total silence, depending on how your radio is programmed.3When you hear “white noise” (that is, the channel is free), press the PTT button to talk and release it to listen. The LED lights up solid yellow.NAG-LACR.book Page 27 Tuesday, March 12, 2013 3:37 PMdraft
Receiving and Making CallsEnglish28Permanent MonitorUse the Permanent Monitor feature to continuously monitor a selected channel for activity.NOTE: This feature is not applicable in Capacity Plus and Linked Capacity Plus.Procedure:1Press the programmed Permanent Monitor button.2Radio sounds alert tone, and the LED lights up solid yellow.3Press the programmed Permanent Monitor button to remove the radio from permanent monitor mode.4Radio sounds an alert tone and the LED turns off.NAG-LACR.book Page 28 Tuesday, March 12, 2013 3:37 PMdraft
Advanced FeaturesEnglish29Advanced Features Use this navigation guide to learn more about advanced features available with your radio:Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 29Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 30Call Indicator Settings . . . . . . . . . . . . . . . . . . . . . . . . . page 32Call Alert Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . page 32Emergency Operation . . . . . . . . . . . . . . . . . . . . . . . . . page 33Privacy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 36Multi-Site Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 37Lone Worker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 38Password Lock Features. . . . . . . . . . . . . . . . . . . . . . . page 38Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 40Auto-Range Transponder System (ARTS) . . . . . . . . . page 41Over-the-Air Programming (OTAP) . . . . . . . . . . . . . . . page 42Utilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 42Scan ListsScan lists are created and assigned to individual channels/groups. Your radio scans for voice activity by cycling through the channel/group sequence specified in the scan list for the current channel.Your radio supports up to 250 scan lists, with a maximum of 16 members in a list. Each scan list shall support a mixture of both analog and digital entries.NOTE: This feature is not applicable in Capacity Plus and Linked Capacity Plus.NAG-LACR.book Page 29 Tuesday, March 12, 2013 3:37 PMdraft
Advanced FeaturesEnglish30ScanWhen you start a scan, your radio cycles through the programmed scan list for the current channel looking for voice activity.The LED blinks yellow.During a dual mode scan, if you are on a digital channel, and your radio locks onto an analog channel, it automatically switches from digital mode to analog mode for the duration of the call. This is also true for the reverse.There are two types of scans: •Main Channel Scan (Manual): Your radio scans all the channels/groups in your scan list. On entering scan, your radio may – depending on the settings – automatically start on the last scanned “active” channel/group or on the channel where scan was initiated.•Auto Scan (Automatic): Your radio automatically starts scanning when you select a channel/group that has Auto Scan enabled.NOTE: This feature is not applicable in Capacity Plus and Linked Capacity Plus.Starting and Stopping ScanProcedure: 1Press the programmed Scan button.ORUse the Channel Selector Knob to select a channel with Auto Scan enabled.2When Scan is enabled, the LED blinks yellow and you hear a positive indicator tone.ORWhen Scan is disabled, the LED turns off and you hear a negative indicator tone.Responding to a Transmission During a ScanDuring scanning, your radio stops on a channel/group where activity is detected. The radio stays on that channel for a programmed time period known as “hang time”.Procedure: 1Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the transmitting radio releases the PTT button, indicating the channel is free for you to respond.NAG-LACR.book Page 30 Tuesday, March 12, 2013 3:37 PMdraft
Advanced FeaturesEnglish312Press the PTT button during hang time. The LED lights up solid green.3Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone.OR Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the microphone.4Release the PTT button to listen.5If you do not respond within the hang time, the radio returns to scanning other channels/groups.Deleting a Nuisance ChannelIf a channel continually generates unwanted calls or noise (termed a “nuisance” channel), you can temporarily remove the unwanted channel from the scan list.This capability does not apply to the channel designated as the Selected Channel.Procedure:1When your radio “locks on to” an unwanted or nuisance channel, press the programmed Nuisance Channel Delete button until you hear a tone.2Release the Nuisance Channel Delete button. The nuisance channel is deleted.Restoring a Nuisance ChannelProcedure: To restore the deleted nuisance channel, do one of the following:•Turn the radio off and power it on again, OR•Stop and restart a scan via the programmed Scan button, OR•Change the channel via the Channel Selector Knob. Vote Scan Vote Scan provides you with wide area coverage in areas where there are multiple base stations transmitting identical information on different analog channels.Your radio scans analog channels of multiple base stations and performs a voting process to select the strongest received signal. Once that is established, your radio unmutes to transmissions from that base station. The LED blinks yellow during the Vote Scan operation.To respond to a transmission during a Vote Scan, follow the same procedures as Responding to a Transmission During a Scan on page 30.NAG-LACR.book Page 31 Tuesday, March 12, 2013 3:37 PMdraft
Advanced FeaturesEnglish32Call Indicator SettingsYou can turn on or off the ringing tones for a received Private Call (see Turning Radio Tones/Alerts On or Off on page 43). Escalating Alarm Tone VolumeYour radio can be programmed by your dealer to continually alert you when a radio call remains unanswered. This is done by automatically increasing the alarm tone volume over time. This feature is known as Escalert.Call Alert OperationCall Alert paging enables you to alert a specific radio user to call you back when they are able to do so. This feature is accessible via a programmed One Touch Access button.Receiving and Responding to a Call AlertProcedure:When you receive a Call Alert page:1You hear a repetitive tone. The LED blinks yellow.2Press the PTT button within four (4) seconds of receiving a Call Alert page to respond to the Private Call.Making a Call Alert with the One Touch Access Button Procedure:1Press the programmed One Touch Access button to make a Call Alert to the predefined ID.2The LED lights up solid green when your radio is sending the Call Alert.3If the Call Alert acknowledgement is received, two chirps sound.ORIf the Call Alert acknowledgement is not received, a low-pitch tone sounds.NAG-LACR.book Page 32 Tuesday, March 12, 2013 3:37 PMdraft
Advanced FeaturesEnglish33Emergency OperationAn Emergency Alarm is used to indicate a critical situation. You are able to initiate an Emergency at any time, in any state, even when there is activity on the current channel.Your dealer can set the duration of a button press for the programmed Emergency button, except for long press, which is similar with all other buttons:•Short press – Between 0.05 seconds and 0.75 seconds•Long press – Between 1.00 second and 3.75 secondsThe Emergency button is assigned with the Emergency On/Off feature. Check with your dealer for the assigned operation of the Emergency button.If short press the Emergency button is assigned to turn on the Emergency mode, then long press the Emergency button is assigned to exit the Emergency mode.If long press the Emergency button is assigned to turn on the Emergency mode, then short press the Emergency button is assigned to exit the Emergency mode.Your radio supports three Emergency Alarms:•Emergency Alarm•Emergency Alarm with Call•Emergency Alarm with Voice to Follow In addition, each alarm has the following types: •Regular – Radio transmits an alarm signal and shows audio and/or visual indicators.•Silent – Radio transmits an alarm signal without any audio or visual indicators. Radio receives calls without any sound through the radio’s speaker, until you press the PTT button to initiate the call.•Silent with Voice – Radio transmits an alarm signal without any audio or visual indicators, but allow incoming calls to sound through the radio’s speaker.Only one of the Emergency Alarms above can be assigned to the programmed Emergency button.Sending an Emergency AlarmThis feature allows you to send an Emergency Alarm, a non-voice signal, which triggers an alert indication on a group of radios.Procedure:1Press the programmed Emergency On button.2The LED lights up solid green.NAG-LACR.book Page 33 Tuesday, March 12, 2013 3:37 PMdraft
Advanced FeaturesEnglish343When an Emergency Alarm acknowledgment is received, the Emergency tone sounds. The LED blinks green. ORIf your radio does not receive an Emergency Alarm acknowledgement, and after all retries have been exhausted, a low-pitch tone sounds.4Radio exits the Emergency Alarm mode.If your radio is set to Silent, it will not display any audio or visual indicators during Emergency mode.Sending an Emergency Alarm with CallThis feature allows you to send an Emergency Alarm to a group of radios. Upon acknowledgement by a radio within the group, the group of radios can communicate over a programmed Emergency channel.Procedure: 1Press the programmed Emergency On button.2The LED lights up solid green.3When an Emergency Alarm acknowledgment is received, the Emergency tone sounds. The LED blinks green. 4Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.5Press the PTT button to make the call. The LED lights up solid green.6Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone.OR Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the microphone.7Release the PTT button to listen.8When the channel is free for you to respond, a short alert tone sounds ( if the Channel Free Indication feature is enabled). Press the PTT button to respond. OROnce your call ends, press Emergency Off button to exit the Emergency mode.If your radio is set to Silent, it will not display any audio or visual indicators during Emergency mode, or allow any received calls to sound through the radio’s speaker, until you press the PTT button to initiate the call.If your radio is set to Silent with Voice, it will not display any audio or visual indicators during Emergency mode, but allow incoming calls to sound through the radio’s speaker. The indicators will only appear once you press the PTT button to initiate, or respond to, the call.NAG-LACR.book Page 34 Tuesday, March 12, 2013 3:37 PMdraft
Advanced FeaturesEnglish35Sending an Emergency Alarm with Voice to Follow This feature allows you to send an Emergency Alarm to a group of radios. Your radio’s microphone is automatically activated, allowing you to communicate with the group of radios without pressing the PTT button.This activated microphone state is also known as “hot mic”.If you press the PTT button during the programmed hot mic transmission period, the radio ignores the PTT press and remains in Emergency mode. NOTE: If you press the PTT button during hot mic, and continue to press it after the hot mic duration expires, the radio continues to transmit until you release the PTT button.Procedure:1Press the programmed Emergency On button.2The LED lights up solid green.3Once a tone sounds, speak clearly into the microphone. When hot mic has been enabled, the radio automatically transmits without a PTT press until the hot mic duration expires.While transmitting, the LED lights up solid green.4The radio automatically stops transmitting when:Once the cycling duration between hot mic and receiving calls expires, if Emergency Cycle Mode is enabled.OROnce the hot mic duration expires, if Emergency Cycle Mode is disabled.5To transmit again, press the PTT button.ORPress the programmed Emergency Off button to exit the Emergency mode.If your radio is set to Silent, it will not display any audio or visual indicators during Emergency mode, or allow any received calls to sound through the radio’s speaker, until the programmed hot mic transmission period is over, and you press the PTT button.If your radio is set to Silent with Voice, it will not display any audio or visual indicators during Emergency mode when you are making the call with hot mic, but allow sound through the radio’s speaker when the target radio responds after the programmed hot mic transmission period is over. The indicators will only appear when you press the PTT button.NOTE: If the Emergency Alarm request fails, the radio does not retry to send the request, and enters the hot mic state directly.NAG-LACR.book Page 35 Tuesday, March 12, 2013 3:37 PMdraft
Advanced FeaturesEnglish36Reinitiating an Emergency ModeNOTE: This feature is only applicable to the radio sending the Emergency Alarm.There are two instances where this can happen:•You change the channel while the radio is in Emergency mode. This exits the Emergency mode. If Emergency Alarm is enabled on this new channel, the radio reinitiates Emergency.•You press the programmed Emergency On button during an Emergency initiation/transmission state. This causes the radio to exit this state, and to reinitiate Emergency.Exiting an Emergency ModeNOTE: This feature is only applicable to the radio sending the Emergency Alarm.Your radio exits Emergency mode when one of the following occurs:•Emergency Alarm acknowledgement is received (for Emergency Alarm only), OR• An Emergency Exit Telegram is received, OR•All retries to send the alarm have been exhausted, OR•The Emergency Off button is pressed.•Turn the radio off and then power it on again if your radio has been programmed to remain on the Emergency Revert channel even after acknowledgement is received.NOTE: If your radio is powered off, it exits the Emergency mode. The radio will not reinitiate the Emergency mode automatically when it is turned on again.Privacy If enabled, this feature helps to prevent eavesdropping by unauthorized users on a channel by the use of a software-based scrambling solution. The signaling and user identification portions of a transmission are not scrambled.Your radio must have privacy enabled on the channel to send a privacy-enabled transmission, although this is not a necessary requirement for receiving a transmission. While on a privacy-enabled channel, the radio is still able to receive clear (unscrambled) transmissions.Your radio supports two types of privacy:•Basic Privacy•Enhanced Privacy (A Software License Key sold separately is required for this feature.) Only ONE of the privacy types above can be assigned to the radio.To unscramble a privacy-enabled call or data transmission, your radio must be programmed to have the same Privacy Key (for Basic Privacy), OR the same Key Value and Key ID (for Enhanced Privacy) as the transmitting radio.NAG-LACR.book Page 36 Tuesday, March 12, 2013 3:37 PMdraft
Advanced FeaturesEnglish37If your radio receives a scrambled call that is of a different Privacy Key, OR a different Key Value and Key ID, you will either hear a garbled transmission (Basic Privacy) or nothing at all (Enhanced Privacy).The LED lights up solid green while the radio is transmitting and blinks green rapidly when the radio is receiving an ongoing privacy-enabled transmission.NOTE: Some radio models may not offer this Privacy feature. Check with your dealer or system administrator for more information.Procedure:Press the programmed Privacy button to toggle privacy on or off.Multi-Site Controls These features are applicable when your current radio channel is part of an IP Site Connect or Linked Capacity Plus configuration. NOTE: See IP Site Connect on page 10 and Linked Capacity Plus on page 12 for more details about these configurations.Starting an Automatic Site SearchNOTE: The radio only scans for a new site if the current signal is weak or when the radio is unable to detect any signal from the current site. If the RSSI value is strong, the radio remains on the current site.Procedure: 1Press the programmed Site Lock On/Off button.2A tone sounds.3The LED blinks yellow rapidly when the radio is actively searching for a new site, and turns off once the radio locks on to a site.The radio also performs an automatic site search (site is unlocked) during a PTT button press or data transmission if the current channel, multi-site channel with an attached roam list, is out of range.Stopping an Automatic Site SearchWhen the radio is actively searching for a new site:Procedure: 1Press the programmed Site Lock On/Off button.2A tone sounds and the LED turns off.NAG-LACR.book Page 37 Tuesday, March 12, 2013 3:37 PMdraft
Advanced FeaturesEnglish38Starting a Manual Site SearchProcedure: 1Press the programmed Manual Site Roam button.2A tone sounds and the LED blinks green.3You hear a positive indicator tone and the LED turns off, indicating the radio is locked on to a site.ORYou hear a negative indicator tone and the LED turns off, indicating the radio is unable to lock on to a site.Lone WorkerThis feature prompts an emergency to be raised if there is no user activity, such as any radio button press or activation of the channel selector, for a predefined time.Following no user activity for a programmed duration, the radio pre-warns the user via an audio indicator once the inactivity timer expires.If there is still no acknowledgment by the user before the predefined reminder timer expires, the radio initiates an Emergency Alarm.Only one of the following Emergency Alarms is assigned to this feature:•Emergency Alarm•Emergency Alarm with Call•Emergency Alarm with Voice to Follow The radio remains in the emergency state allowing voice messages to proceed until action is taken. See Emergency Operation on page 33 on ways to exit Emergency.NOTE: This feature is limited to radios with this function enabled. Check with your dealer or system administrator for more information.Password Lock FeaturesIf enabled, this feature allows you to access your radio via password upon powering up. Use the Channel Selector Knob and the three Side Buttons to enter password (see Linked Capacity Plus page 12 on page 6):•Channel Selector Knob positions 1 to 9 represent numbers 1 to 9, and position 10 represents number 0.•Side Buttons 1 to 2 represent numbers 1 to 2.Accessing the Radio from PasswordProcedure:Power up the radio.1You hear a continuous tone.NAG-LACR.book Page 38 Tuesday, March 12, 2013 3:37 PMdraft
Advanced FeaturesEnglish392Use the Channel Selector Knob to enter the first digit of the password.3Press Side Button 1 or 2 to enter each digit of the remaining three digits of the password. You hear a positive indicator tone for each Side Button press.When the second digit of the password is entered, your radio ignores any Channel Selector Knob position change.4When the last digit of the four-digit password is entered, your radio automatically checks the validity of the password.If the password is correct:Your radio proceeds to power up. See Powering Up the Radio on page 5.ORIf the password is incorrect:You hear a continuous tone. Repeat Steps 1 to 3.ORAfter the third incorrect password, your radio enters into locked state. A tone sounds and the LED double blinks yellow.Your radio enters into locked state for 15 minutes, and responds to inputs from On/Off/Volume Control Knob.NOTE: The radio is unable to receive any call, including emergency calls, in locked state.Unlocking the Radio from Locked StateProcedure:Wait for 15 minutes. Repeat Steps 1 to 4 in Accessing the Radio from Password on page 38.ORPower up the radio, if you have powered down the radio during locked state:1A tone sounds and the LED double blinks yellow.2Wait for 15 minutes. Repeat Steps 1 to 4 in Accessing the Radio from Password on page 38.Your radio restarts the 15 minute timer for locked state when you power up.NAG-LACR.book Page 39 Tuesday, March 12, 2013 3:37 PMdraft
Advanced FeaturesEnglish40BluetoothThis feature allows you to use your radio with a Bluetooth-enabled device (accessory) via a Bluetooth connection. Your radio supports both Motorola and COTS (Commercially available Off-The-Shelf) Bluetooth-enabled devices. Bluetooth operates within a range of 10 meters line of sight. This is an unobstructed path between your radio and your Bluetooth-enabled device.It is not recommended that you leave your radio behind and expect your Bluetooth-enabled device to work with a high degree of reliability when they are separated.At the fringe areas of reception, both voice and tone quality will start to sound "garbled" or "broken". To correct this problem, simply position your radio and Bluetooth-enabled device closer to each other (within the 10-meter defined range) to re-establish clear audio reception. Your radio’s Bluetooth function has a maximum power of 2.5 mW (4 dBm) at the 10-meter range. Your radio can support up to 3 simultaneous Bluetooth connections with Bluetooth-enabled devices of unique types. For example, a headset, a scanner, and a PTT-Only Device (POD). Multiple connections with Bluetooth-enabled devices of the same type are not supported. Refer to your respective Bluetooth-enabled device’s user manual for more details on your Bluetooth-enabled device’s full capabilities.Finding and Connecting to a Bluetooth DeviceProcedure:1Turn on your Bluetooth-enabled device and place it in pairing mode. Refer to respective Bluetooth-enabled device’s user manual. 2On your radio, press the programmed Bluetooth Connect button.3A tone sounds and LED blinks yellow.4Your Bluetooth-enabled device may require additional steps to complete the pairing. Refer to respective Bluetooth-enabled device’s user manual.5If successful, a positive tone sounds.ORIf unsuccessful, a negative indicator tone sounds. Do not turn off your Bluetooth-enabled device during the finding and connecting operation as this cancels the operation. Your radio connects to the Bluetooth-enabled device within range with either the strongest signal strength, or to one which it has connected to before in a prior session. NOTE: A pin code may be required to be programmed in your radio before it can pair with some devices. Contact your dealer for more information. NAG-LACR.book Page 40 Tuesday, March 12, 2013 3:37 PMdraft
Advanced FeaturesEnglish41Disconnecting from a Bluetooth DeviceProcedure:1Press the programmed Bluetooth Disconnect button.2A positive indicator tone sounds when disconnected. Switching Audio Route You can toggle audio routing between internal radio speaker and external Bluetooth-enabled accessory. Procedure:1Press the programmed Bluetooth Audio Switch button.A tone sounds when the audio route has switched.Auto-Range Transponder System (ARTS)ARTS is an analog-only feature designed to inform you when your radio is out-of-range of other ARTS-equipped radios.ARTS-equipped radios transmit or receive signals periodically to confirm that they are within range of each other. Your dealer can program your radio to transmit or receive the ARTS signal. Your radio provides indications of states as follows:•First-Time Alert – A tone sounds.•ARTS-in-Range Alert – A tone sounds, if programmed. •ARTS-Out-of-Range Alert – A tone sounds, and the LED rapidly blinks red.NAG-LACR.book Page 41 Tuesday, March 12, 2013 3:37 PMdraft
Advanced FeaturesEnglish42Over-the-Air Programming (OTAP) Your radio can be updated by your dealer remotely, via OTAP, without needing to be physically connected. Additionally, some settings can also be configured via OTAP. While undergoing OTAP, the LED blinks green. NOTE: When the radio is receiving high volume data, the channel is busy. A PTT button press at this time causes a negative tone to sound. Once the programming is complete, a tone sounds, and your radio restarts (powers off and on again). UtilitiesSetting the Squelch Level You can adjust your radio's squelch level to filter out unwanted calls with low signal strength or channels that have a higher than normal background noise.Settings: Normal is the default. Tight filters out (unwanted) calls and/or background noise. However, calls from remote locations may also be filtered out.Procedure: 1Press the programmed Squelch button.2You hear a positive indicator tone, indicating the radio is operating in tight squelch.ORYou hear a negative indicator tone, indicating the radio is operating in normal squelch.Setting the Power Level You can toggle your radio’s power setting between high or low for each channel.Settings: High enables communication with radios located at a considerable distance from you. Low enables communication with radios in closer proximity. NAG-LACR.book Page 42 Tuesday, March 12, 2013 3:37 PMdraft
Advanced FeaturesEnglish43Procedure: 1Press the programmed Power Level button.2You hear a positive indicator tone, indicating the radio is transmitting at low power.ORYou hear a negative indicator tone, indicating the radio is transmitting at high power.Turning the Voice Operating Transmission (VOX) Feature On or OffThis feature allows you to initiate a hands-free voice activated call on a programmed channel. The radio automatically transmits, for a programmed period, whenever the microphone on the VOX-capable accessory detects voice.Pressing the PTT button during radio operation will disable VOX. To re-enable VOX, do one of the following:•Turn the radio off and power it on again, OR•Change the channel via the Channel Selector Knob, OR•Follow the procedure below.NOTE: Turning this feature on or off is limited to radios with this function enabled. Check with your dealer or system administrator for more information.Procedure: Press the programmed VOX button to toggle the feature on or off.If the Talk Permit Tone feature is enabled, use a trigger word to initiate the call. Wait for the Talk Permit Tone to finish before speaking clearly into the microphone.Turning the Howling Suppressor Feature On or Off This feature allows you to minimize acoustic feedback in received calls.Procedure: 1Press the programmed AF Suppressor button.2You hear a positive indicator tone, indicating that Howling Suppressor is now enabled.ORYou hear a negative indicator tone, indicating that the radio is unable to activate Howling Suppressor.Turning Radio Tones/Alerts On or Off You can enable and disable all radio tones and alerts (except for the incoming Emergency alert tone) if needed.Procedure: 1Press the programmed All Tones/Alerts button.NAG-LACR.book Page 43 Tuesday, March 12, 2013 3:37 PMdraft
Advanced FeaturesEnglish442You hear a positive indicator tone, indicating all tones and alerts are on.ORYou hear a negative indicator tone, indicating all tones and alerts are off.Checking the Battery StrengthYou can check how much battery power you have left.Settings: The LED Indicator in solid yellow indicates fair battery charge while solid green indicates full charge of the battery.Procedure: Press the programmed Battery Strength button to view the battery strength via the LED Indicator.NAG-LACR.book Page 44 Tuesday, March 12, 2013 3:37 PMdraft
AccessoriesEnglish45AccessoriesYour radio is compatible with the accessories listed in this chapter. Contact your dealer for details.Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 45Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 45Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 45Carry Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 45Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 45Earbuds and Earpieces . . . . . . . . . . . . . . . . . . . . . . . . page 46Headsets and Headset Accessories . . . . . . . . . . . . . . page 47Remote Speaker s. . . . . . . . . . . . . . . . . . . . . . . . . . . . page 47Surveillance Accessories. . . . . . . . . . . . . . . . . . . . . . . page 48Miscellaneous Accessories . . . . . . . . . . . . . . . . . . . . . page 48Antennas•VHF, 136 – 148MHz, Stubby Antenna (PMAD4119_)•VHF, 146 – 160MHz, Stubby Antenna (PMAD4120_)•VHF, 160 – 174MHz, Stubby Antenna (PMAD4121_)•UHF, 403 – 450MHz, Stubby Antenna (PMAE4069_)•UHF, 440 – 490MHz, Stubby Antenna (PMAE4070_)•UHF, 470 – 527MHz, Stubby Antenna (PMAE4071_)Batteries•Li-Ion, 1600mAH IP67 Battery (PMNN4440_)Cables•Programming Cable USB (PMKN4115_)•Programming Cable Slim Connector to DB25 and USB Plug (PMKN4117_)•Programming Cable Slim Connector to DB25 and TTR (PMKN4116_)Carry Devices•Plastic Carry Case with Belt Clip (PMLN6545_)Chargers•Single-Unit Charger, US Plug (PMTN4024_)•Single-Unit Charger, EURO Plug (PMTN4025_)•Single-Unit Charger, UK Plug (PMTN4026_)•Core Single-Unit Charger, with Power Supply, US (AAHTN3000_)•Core Single-Unit Charger, Base Only (HTN9000_)NAG-LACR.book Page 45 Tuesday, March 12, 2013 3:37 PMdraft
AccessoriesEnglish46•Core Single-Unit Charger, Base Only (MDHTN9000_)•Core Single-Unit Charger, with Switch Mode Power Supply, UK (PMLN5195_)•Core Single-Unit Charger, with Switch Mode Power Supply, EURO (PMLN5196_)•Core Single-Unit Charger, with Switch Mode Power Supply, US (PMLN5197_)•IMPRES Single-Unit Charger, with Power Supply, US (WPLN4182_)•IMPRES Single-Unit Charger, with Power Supply, UK (WPLN4183_)•IMPRES Single-Unit Charger, with Power Supply, EURO (WPLN4184_)•IMPRES Single-Unit Charger, without Power Supply, US (WPLN4199_)•IMPRES Single-Unit Charger, with Power Supply (WPLN4206_)•IMPRES Single-Unit Charger, with Switch Mode Power Supply, EURO (PMLN5188_)•IMPRES Single-Unit Charger, with Switch Mode Power Supply, UK (PMLN5194_)•IMPRES Single-Unit Charger, with Switch Mode Power Supply, US (PMLN5198_)•IMPRES Single-Unit Charger, with Switch Mode Power Supply, Australia/New Zealand (PMLN5199_)•Daisy Chain Charger (JMTN4011_)•Multi-Unit Charger, UK Cord (WPLN4188_)•Multi-Unit Charger, EURO Cord (WPLN4189_)•Multi-Unit Charger, Australia/New Zealand Cord (WPLN4190_)•Multi-Unit Charger, no Power Cord (WPLN4197_)•Multi-Unit Charger, US Cord (WPLN4205_)•Multi-Unit Charger, with Display, US Plug (WPLN4192_)•Multi-Unit Charger, with Display, UK Plug (WPLN4193_)•Multi-Unit Charger, with Display, EURO Plug (WPLN4194_)•Multi-Unit Charger, with Display, Australia/New Zealand Plug (WPLN4195_)•Multi-Unit Charger, with Display, no Power Cord (WPLN4198_)•Multi-Unit Charger, with Display, US Plug (WPLN4204_)•Micro USB Travel Charger (SPN5334_)Earbuds and Earpieces•Earbud with In-Line Mic/PTT, MagOne (PMLN5733_)NAG-LACR.book Page 46 Tuesday, March 12, 2013 3:37 PMdraft
AccessoriesEnglish47•Earpiece In-Line Mic/PTT Swivel, MagOne (PMLN5727_)•Receive-Only Covered Earbud with Coiled Cord, for Remote Speaker (AARLN4885_)•Receive-Only Flexible Earpiece for Remote Speaker (WADN4190_)•D-Shell Receive Only Earpiece (One Size) for Remote Speaker (PMLN4620_)•Receiver-Only Earpiece with Translucent Tube and Rubber Eartip for Remote Speaker (RLN4941_)•1-Wire Earbud, 29cm Cord, Black (NNTN8294_)•1-Wire Earbud,116cm Cord, Black (NNTN8295_)•Wireless Earpiece Maintenance Kit (NTN8821_)•Ear Straps for CommPort Earpiece (for Secure Attachment to Ear), Pack of 10 (NTN8988_)•Replacement Ear Tubes for CommPort Earpiece, Pack of 10 (RLN5037_)•Replacement Ear Tips Kit for Wireless Ear Buds (NNTN8316_)Headsets and Headset Accessories•Heavy Duty Headset, Noise Cancelling with In-Line PTT (PMLN5731_)•Earset with Boom Microphone, MagOne (PMLN5732_)•Non-Secure Wireless Headset & Push-to-Talk Device with Push-to-Talk Audio, 12-Inch Cable (NNTN8125_)(NNTN8189_)•Non-Secure Wireless Headset & Push-to-Talk Device with Push-to-Talk Audio, 9.5-Inch Cable (NNTN8126_)•Non-Secure Wireless Headset & Push-to-Talk Device with Push-to-Talk Audio, 9-Inch Cable with Euro/UK Plug (GMTN6356_)•Non-Secure Wireless Push-to-Talk Device (NNTN8127_)•Push-to-Talk Module, without Charger (NNTN8191_)•Non-Secure HK200 Mobile Bluetooth Headset with US Plug (89409N)•Replacement Earpiece 12” Cable (for NNTN8125_) (NTN2572_)•Replacement Earpiece 9.5” Cable (for NNTN8126_) (NTN2575_)•Non-Secure Wireless Push-to-Talk Device (for NNTN8125_ and NNTN8126_) (NNTN8143_)•Remote Speaker s•IMPRES Remote Speaker Large, Noise Cancelling with 3.5mm Jack (PMMN4071_)NAG-LACR.book Page 47 Tuesday, March 12, 2013 3:37 PMdraft
AccessoriesEnglish48•IMPRES Remote Speaker Small, with 3.5mm Jack (PMMN4073_)•Remote Speaker Small, No Emergency, IP57 (PMMN4075_)•Remote Speaker Small with 3.5mm Jack (PMMN4076_)Surveillance Accessories•2-Wire Surveillance Kit, Black (PMLN5724_)•2-Wire Surveillance Kit, Beige (PMLN5726_)Miscellaneous Accessories• Replacement Micro-USB Plug-In Charger (PMPN4009_)NAG-LACR.book Page 48 Tuesday, March 12, 2013 3:37 PMdraft
Appendix: Maritime Radio Use in the VHF Frequency RangeEnglish49Appendix: Maritime Radio Use in the VHF Frequency RangeTake a moment to review the following:Special Channel Assignments . . . . . . . . . . . . . . . . . . . page 49Operating Frequency Requirements . . . . . . . . . . . . . . page 50Declaration of Compliance for the Use of Distress and Safety Frequencies. . . . . . . . . . . . . . . page 52Technical Parameters for InterfacingExternal Data Sources. . . . . . . . . . . . . . . . . . . . . . . page 52Special Channel AssignmentsEmergency ChannelIf you are in imminent and grave danger at sea and require emergency assistance, use VHF Channel 16 to send a distress call to nearby vessels and the United States Coast Guard. Transmit the following information, in this order:1“MAYDAY, MAYDAY, MAYDAY.”2“THIS IS _____________________, CALL SIGN __________.”State the name of the vessel in distress 3 times, followed by the call sign or other identification of the vessel, stated 3 times.3Repeat “MAYDAY” and the name of the vessel.4“WE ARE LOCATED AT _______________________.” State the position of the vessel in distress, using any information that will help responders to locate you, e.g.:• latitude and longitude• bearing (state whether you are using true or magnetic north)• distance to a well-known landmark• vessel course, speed or destination5State the nature of the distress.6Specify what kind of assistance you need.7State the number of persons on board and the number needing medical attention, if any.8Mention any other information that would be helpful to responders, such as type of vessel, vessel length and/or tonnage, hull color, etc.9“OVER.”10 Wait for a response.11 If you do not receive an immediate response, remain by the radio and repeat the transmission at intervals until you receive a response. Be prepared to follow any instructions given to you.NAG-LACR.book Page 49 Tuesday, March 12, 2013 3:37 PMdraft
Appendix: Maritime Radio Use in the VHF Frequency RangeEnglish50Non-Commercial Call ChannelFor non-commercial transmissions, such as fishing reports, rendezvous arrangements, repair scheduling, or berthing information, use VHF Channel 9.Operating Frequency RequirementsA radio designated for shipboard use must comply with Federal Communications Commission Rule Part 80 as follows:•on ships subject to Part II of Title III of the Communications Act, the radio must be capable of operating on the 156.800 MHz frequency•on ships subject to the Safety Convention, the radio must be capable of operating:• in the simplex mode on the ship station transmitting frequencies specified in the 156.025 – 157.425 MHz frequency band, and• in the semiduplex mode on the two frequency channels specified in the table below.NOTE: Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters.Additional information about operating requirements in the Maritime Services can be obtained from the full text of FCC Rule Part 80 and from the US Coast Guard.Table A-1: VHF Marine Channel ListChannel NumberFrequency (MHz)Transmit Receive1 156.050 160.6502 156.100 160.700* 156.150 160.7504 156.200 160.8005 156.250 160.8506 156.300 –7 156.350 160.9508 156.400 –9 156.450 156.45010 156.500 156.50011 156.550 156.55012 156.600 156.60013** 156.650 156.65014 156.700 156.70015** 156.750 156.75016 156.800 156.80017** 156.850 156.85018 156.900 161.50019 156.950 161.550NAG-LACR.book Page 50 Tuesday, March 12, 2013 3:37 PMdraft
Appendix: Maritime Radio Use in the VHF Frequency RangeEnglish51* Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters.** Low power (1 W) only*** Guard bandNOTE: A – in the Receive column indicates that the channel is transmit only.20 157.000 161.600* 157.050 161.65022 157.100 161.700* 157.150 161.75024 157.200 161.80025 157.250 161.85026 157.300 161.90027 157.350 161.95028 157.400 162.00060 156.025 160.625* 156.075 160.67562 156.125 160.72563 156.175 160.775* 156.225 160.82565 156.275 160.87566 156.325 160.92567** 156.375 156.37568 156.425 156.42569 156.475 156.47571 156.575 156.57572 156.625 –73 156.675 156.675Table A-1: VHF Marine Channel List (Continued)Channel NumberFrequency (MHz)Transmit Receive74 156.725 156.72575 *** ***76 *** ***77** 156.875 –78 156.925 161.52579 156.975 161.57580 157.025 161.625* 157.075 161.675* 157.125 161.725* 157.175 161.77584 157.225 161.82585 157.275 161.87586 157.325 161.92587 157.375 161.97588 157.425 162.025Table A-1: VHF Marine Channel List (Continued)Channel NumberFrequency (MHz)Transmit ReceiveNAG-LACR.book Page 51 Tuesday, March 12, 2013 3:37 PMdraft
Appendix: Maritime Radio Use in the VHF Frequency RangeEnglish52Declaration of Compliance for the Use of Distress and Safety FrequenciesThe radio equipment does not employ a modulation other than the internationally adopted modulation for maritime use when it operates on the distress and safety frequencies specified in RSS-182 Section 7.3.Technical Parameters for Interfacing External Data SourcesRS232 USB SB9600Input Voltage (Volts Peak-to-peak)18V 3.6V 5VMax Data Rate 28 kb/s 12 Mb/s 9.6 kb/sImpedance 5k ohm 90 ohm 120 ohmNAG-LACR.book Page 52 Tuesday, March 12, 2013 3:37 PMdraft
Batteries and Chargers WarrantyEnglish53Batteries and Chargers WarrantyThe Workmanship Warranty The workmanship warranty guarantees against defects in workmanship under normal use and service.The Capacity WarrantyThe capacity warranty guarantees 80% of the rated capacity for the warranty duration.All MOTOTRBO Batteries Two (2) YearsIMPRES Chargers (Single-Unit and Multi-Unit, Non-Display) Two (2) YearsIMPRES Chargers (Multi-Unit with Display) One (1) YearLithium-Ion (Li-lon) Batteries 12 MonthsIMPRES Batteries, When Used Exclusively with IMPRES Chargers 18 MonthsNAG-LACR.book Page 53 Tuesday, March 12, 2013 3:37 PMdraft
Limited WarrantyEnglish54Limited WarrantyMOTOROLA COMMUNICATION PRODUCTSI. WHAT THIS WARRANTY COVERS AND FOR HOW LONG:MOTOROLA SOLUTIONS, INC. (“MOTOROLA”) warrants the MOTOROLA manufactured Communication Products listed below (“Product”) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below:MOTOROLA, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it (with a new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided it is returned in accordance with the terms of this warranty. Replaced parts or boards are warranted for the balance of the original applicable warranty period. All replaced parts of Product shall become the property of MOTOROLA.This express limited warranty is extended by MOTOROLA to the original end user purchaser only and is not assignable or transferable to any other party. This is the complete warranty for the Product manufactured by MOTOROLA. MOTOROLA assumes no obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of MOTOROLA. Unless made in a separate agreement between MOTOROLA and the original end user purchaser, MOTOROLA does not warrant the installation, maintenance or service of the Product.MOTOROLA cannot be responsible in any way for any ancillary equipment not furnished by MOTOROLA which is attached to or used in connection with the Product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use the Product is unique, MOTOROLA disclaims liability for range, coverage, or operation of the system as a whole under this warranty.II. GENERAL PROVISIONS:This warranty sets forth the full extent of MOTOROLA'S responsibilities regarding the Product. Repair, replacement or refund of the purchase price, at MOTOROLA’s option, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME, XPR Series Digital Portable Radios Two (2) YearsProduct Accessories (Excluding Batteries, Chargers and Mag One Accessories)One (1) YearMag One Accessories Six (6) MonthsNAG-LACR.book Page 54 Tuesday, March 12, 2013 3:37 PMdraft
Limited WarrantyEnglish55INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW.III. STATE LAW RIGHTS:SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY. This warranty gives specific legal rights, and there may be other rights which may vary from state to state.IV. HOW TO GET WARRANTY SERVICE:You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to receive warranty service and, also, deliver or send the Product item, transportation and insurance prepaid, to an authorized warranty service location. Warranty service will be provided by MOTOROLA through one of its authorized warranty service locations. If you first contact the company which sold you the Product (e.g., dealer or communication service provider), it can facilitate your obtaining warranty service. You can also call MOTOROLA at 1-800-927-2744 US/Canada.V. WHAT THIS WARRANTY DOES NOT COVER:A) Defects or damage resulting from use of the Product in other than its normal and customary manner.B) Defects or damage from misuse, accident, water, or neglect.C)Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment.D)Breakage or damage to antennas unless caused directly by defects in material workmanship.E) A Product subjected to unauthorized Product modifications, disassembles or repairs (including, without limitation, the addition to the Product of non-MOTOROLA supplied equipment) which adversely affect performance of the Product or interfere with MOTOROLA's normal warranty inspection and testing of the Product to verify any warranty claim.F) Product which has had the serial number removed or made illegible.G)Rechargeable batteries if:(1) any of the seals on the battery enclosure of cells are broken or show evidence of tampering.(2) the damage or defect is caused by charging or using the battery in equipment or service other than the Product for which it is specified.H)Freight costs to the repair depot.I) A Product which, due to illegal or unauthorized alteration of the software/firmware in the Product, does not function in accordance with MOTOROLA’s published specifications or the FCC certification labeling in effect for the Product at the time the Product was initially distributed from MOTOROLA.NAG-LACR.book Page 55 Tuesday, March 12, 2013 3:37 PMdraft
Limited WarrantyEnglish56J) Scratches or other cosmetic damage to Product surfaces that does not affect the operation of the Product.K) Normal and customary wear and tear.VI. PATENT AND SOFTWARE PROVISIONS:MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA will pay those costs and damages finally awarded against the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following:A) that MOTOROLA will be notified promptly in writing by such purchaser of any notice of such claim;B) that MOTOROLA will have sole control of the defense of such suit and all negotiations for its settlement or compromise; andC)should the Product or parts become, or in MOTOROLA’s opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit MOTOROLA, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA.MOTOROLA will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary equipment or software not furnished by MOTOROLA which is attached to or used in connection with the Product. The foregoing states the entire liability of MOTOROLA with respect to infringement of patents by the Product or any parts thereof.Laws in the United States and other countries preserve for MOTOROLA certain exclusive rights for copyrighted MOTOROLA software such as the exclusive rights to reproduce in copies and distribute copies of such MOTOROLA software. MOTOROLA software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used to produce any derivative thereof. No other use including, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of such MOTOROLA software or exercise of rights in such MOTOROLA software is permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA patent rights or copyrights.VII. GOVERNING LAW:This Warranty is governed by the laws of the State of Illinois, U.S.A.NAG-LACR.book Page 56 Tuesday, March 12, 2013 3:37 PMdraft

Navigation menu