Motorola Solutions 89FC5798 Non-Broadcast Transmitter User Manual Quad BR 800 Tx FCC Filing

Motorola Solutions, Inc. Non-Broadcast Transmitter Quad BR 800 Tx FCC Filing

Exhibit D Users Manual per 2 1033 c3

APPLICANT:  MOTOROLA  INC. EQUIPMENT TYPE:  ABZ89FC5798EXHIBIT 8 INSTRUCTION MANUALSThe instruction and service manual for this base radio are not published at this time.  However, draft copy of themanual is available and has been included as part of the filing package in the form of an electronic pdf document.Upon request, published and/or printed manuals will be sent to the commission and/or telecommunicationcertification body (TCB) as soon as they become available.  All of the descriptions and schematics included thisfiling package are up to date.
APPLICANT:  MOTOROLA  INC. EQUIPMENT TYPE:  ABZ89FC5798EXHIBIT 9TUNE-UP PROCEDUREThere is no field tune-up procedure.  All adjustments are software controlled and are pre-set at the factory.  Certainstation operating parameters can be changed via man-machine interface (MMI) commands, within predeterminedlimits.  Examples include transmit / receiver operating frequencies and power level.
 68P80801H45-1ECCN 5E992Global Telecommunications  Solutions Sector  ENHANCED BASE TRANSCEIVER SYSTEM (EBTS) VOLUME 2 OF 3BASE RADIOS © 2002 Motorola, Inc.All Rights ReservedPrinted in U.S.A. PRELIMINARY
 FCC INTERFERENCE WARNING The FCC requires that manuals pertaining to Class A computing devices must contain warnings about possible interference with local residential radio and TV reception. This warning reads as follows:Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. INDUSTRY OF CANADA NOTICE OF COMPLIANCE This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. COMMERCIAL WARRANTY (STANDARD) Motorola radio communications products (the “Product”) is warranted to be free from defects in material and workmanship for a period of ONE (1) YEAR (except for crystals and channel elements which are warranted for a period of ten (10 years) from the date of shipment. Parts including crystals and channel elements, will be replaced free of charge for the full warranty period but the labor to replace defective parts will only be provided for One Hundred-Twenty (120) days from the date of shipment. Thereafter purchaser must pay for the labor involved in repairing the Product or replacing the parts at the prevailing rates together with any transportation charges to or from the place where warranty service is provided. This express warranty is extended by Motorola, 1301 E. Algonquin Road, Schaumburg, Illinois 60196 to the original end use purchaser only, and only to those purchasing for purpose of leasing or solely for commercial, industrial, or governmental use.THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED WHICH ARE SPECIFICALLY EXCLUDED, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW.In the event of a defect, malfunction or failure to conform to specifications established by Motorola, or if appropriate to specifications accepted by Motorola in writing, during the period shown, Motorola, at its option, will either repair or replace the product or refund the purchase price thereof. Repair at Motorola's option, may include the replacement of parts or boards with functionally equivalent reconditioned or new parts or boards. Replaced parts or boards are warranted for the balance of the original applicable warranty period. All replaced parts or product shall become the property of Motorola.This express commercial warranty is extended by Motorola to the original end user purchaser or lessee only and is not assignable or transferable to any other party. This is the complete warranty for the Product manufactured by Motorola. Motorola assume no obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of Motorola. Unless made in a separate agreement between Motorola and the original end user purchaser, Motorola does not warrant the installation, maintenance or service of the Products.Motorola cannot be responsible in any way for any ancillary equipment not furnished by Motorola which is attached to or used in connection with the Product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use Product is unique, Motorola disclaims liability for range, coverage, or operation of the system as a whole under this warranty.This warranty does not cover:a) Defects or damage resulting from use of the Product in other than its normal and customary manner.b) Defects or damage from misuse, accident, water or neglect c) Defects or damage from improper testing, operation, maintenance installation, alteration, modification, or adjusting. d) Breakage or damage to antennas unless caused directly by defects in material workmanship. e) A Product subjected to unauthorized Product modifications, disassemblies or repairs (including without limitation, the addition to the Product of non-Motorola supplied equipment) which adversely affect performance of the Product or interfere with Motorola's normal warranty inspection and testing of the Product to verify any warranty claim.f) Product which has had the serial number removed or made illegible. g) A Product which, due to illegal to unauthorized alteration of the software/firmware in the Product, does not function in accordance with Motorola's published specifications or the FCC type acceptance labeling in effect for the Product at the time the Product was initially distributed from Motorola.This warranty sets forth the full extent of Motorola's responsibilities regarding the Product. Repair, replacement or refund of the purchase date, at Motorola’s option is the exclusive remedy. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF USE, LOSS OR TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGE ARISING OUT OF THE USE OR INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW. SOFTWARE NOTICE/WARRANTY Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted Motorola software such as the exclusive rights to reproduce in copies and distribute copies of such Motorola software. Motorola software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used to produce any derivative thereof. No other use including without limitation alteration, modification, reproduction, distribution, or reverse engineering of such Motorola software or exercise of rights in such Motorola software is permitted. No license is granted by implication, estoppel or otherwise under Motorola patent rights or copyrights.This warranty extends only to individual products: batteries are excluded, but carry their own separate limited warranty.In order to obtain performance of this warranty, purchaser must contact its Motorola salesperson or Motorola at the address first above shown, attention Quality Assurance Department.This warranty applies only within the fifty (50) United States and the District of Columbia.
68P80801H45-1 1/20/2002 11Global Telecommunications  Solutions Sector 1301 E. Algonquin Road, Schaumburg, IL 60196 Base RadiosAbout This VolumeVolume 2 of the Enhanced Base Transceiver System (EBTS) manual, Base Radios, provides the experienced service technician with an overview of the EBTS operation and functions, and contains information regarding the 800 MHz, 900 MHz, 1500 MHz Single Channel and 800 MHz and 900 MHz QUAD Channel Channel base radios.   The EBTS System has three major components:❐Generation 3 Site Controller (Gen 3 SC) or an integrated Site Controller (iSC)❐Base Radios (BRs)❐RF Distribution System (RFDS)Installation and testing is described in Volume 1, System Installation and Testing, and RFDS are described in Volume 3, RF Distribution Systems (RFDS). Detailed information about the Gen 3 SC is contained in the Gen 3 SC Supplement Manual, 68P80801E30. Detailed information about the iSC is contained in the iSC Supplement Manual, 68P81098E05The information in this manual is current as of the printing date.  If changes to this manual occur after the printing date, they will be documented and issued as Schaumburg Manual Revisions (SMRs). Target AudienceThe target audience of this document includes field service technicians responsible for installing, maintaining, and troubleshooting the EBTS. In keeping with Motorola’s field replaceable unit (FRU) philosophy, this manual provides sufficient functional information to the FRU level. Please refer to the appropriate section of this manual for removal and replacement instructions.
12 68P80801H45-1   1/20/2002Base Radios EBTS System Manual - Vol 2 Maintenance PhilosophyThe EBTS has been designed using a Field Replaceable Unit (FRU) maintenance concept.  To minimize system down time, faulty FRUs may be quickly and easily replaced with replacement FRUs.  This helps to restore normal system operation quickly.Due to the high percentage of surface mount components and multi-layer circuit boards, field repair is discouraged.  Faulty or suspect FRUs should be returned to the Motorola Customer Support Center for further troubleshooting and repair.Each FRU has a bar code label attached to its front panel.  This label identifies a sequential serial number for the FRU.  Log this number whenever contacting the Motorola Customer Support Center.  For complete information on ordering replacement FRUs, or instructions on how to return faulty FRUs for repair, contact:Nippon Motorola LTD.        OR Motorola Customer Support CenterTokyo Service Center 1311 East Algonquin Road044-366-8860 Schaumburg, Illinois 60196(800) 448-3245 or (847) 576-7300Technical Support ServiceMotorola provides technical support services for installation, optimization, and maintenance of its fixed network equipment. Before calling the Motorola Customer Support Center, please note the following information:❐Where the system is located.❐The date the system was put into service.❐A brief description of problem. ❐Any other unusual circumstances.
68P80801H45-1   1/20/2002 13EBTS System Manual - Vol 2 Base RadiosGeneral Safety Information General Safety InformationThe following general safety precautions must be observed during all phases of operation, service, and repair of the equipment described in this manual. The safety precautions listed below represent warnings of certain dangers of which we are aware. You should follow these warnings and all other safety precautions necessary for the safe operation of the equipment in your operating environment.Read and follow all warning notices and instructions marked on the product or included in this manual before installing, servicing or operating the equipment. Retain these safety instructions for future reference. Also, all applicable safety procedures, such as Occupational, Safety, and Health Administration (OSHA) requirements, National Electrical Code (NEC) requirements, local code requirements, safe working practices, and good judgement must be used by personnel.Refer to appropriate section of the product service manual for additional pertinent safety information.Because of the danger of introducing additional hazards, do not install substitute parts or perform any unauthorized modifications of equipment.Identify maintenance actions that require two people to perform the repair. Two people are required when:A repair has the risk of injury that would require one person to perform first aid or call for emergency support. An example would be work around high voltage sources. A second person may be required to remove power and call for emergency aid if an accident occurs to the first person.Use the National Institute of Occupational Safety and Health (NIOSH) listing equation to determine whether a one or two person lift is required when a system component must be removed and replaced in its rack.If troubleshooting the equipment while power is applied, be aware of the live circuits.DO NOT operate the transmitter of any radio unless all RF connectors are secure and all connectors are properly terminated.All equipment must be properly grounded in accordance with Motorola Standards and Guidelines for Communications Sites “R56” 68P81089E50 and specified installation instructions for safe operation.Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and protect it from overheating, these slots and openings must not be blocked or covered.Only a qualified technician familiar with similar electronic equipment should service equipment.Some equipment components can become extremely hot during operation. Turn off all power to the equipment and wait until sufficiently cool before touching.
14 68P80801H45-1   1/20/2002Base Radios EBTS System Manual - Vol 2General Safety Information Human Exposure ComplianceThis equipment is designed to generate and radiate radio frequency (RF) energy by means of an external antenna. When terminated into a non-radiating RF load, the base station equipment is certified to comply with Federal Communications Commission (FCC) regulations pertaining to human exposure to RF radiation in accordance with the FCC Rules Part 1 section 1.1310 as published in title 47 code of federal regulations and procedures established in TIA/EIA TSB92, Report on EME Evaluation for RF Cabinet Emissions Under FCC MPE Guidelines, Compliance to FCC regulations of the final installation should be assessed and take into account site specific characteristics such as type and location of antennas, as well as site accessibility of occupational personnel (controlled environment) and the general public (uncontrolled environment). This equipment should only be installed and maintained by trained technicians. Licensees of the FCC using this equipment are responsible for insuring that its installation and operation comply with FCC regulations Part 1 section 1.1310 as published in title 47 code of federal regulations.Whether a given installation meets FCC limits for human exposure to radio frequency radiation may depend not only on this equipment but also on whether the “environments” being assessed are being affected by radio frequency fields from other equipment, the effects of which may add to the level of exposure. Accordingly, the overall exposure may be affected by radio frequency generating facilities that exist at the time of the licensee’s equipment is being installed or even by equipment installed later. Therefore, the effects of any such facilities must be considered in site selection and in determining whether a particular installation meets the FCC requirements.FCC OET Bulletin 65 provides materials to assist in making determinations if a given facility is compliant with the human exposure to RF radiation limits. Determining the compliance of transmitter sites of various complexities may be accomplished by means of computational methods. For more complex sites direct measurement of power density may be more expedient. Additional information on the topic of electromagnetic exposure is contained in the Motorola Standards and Guideline for Communications Sites publication. Persons responsible for installation of this equipment are urged to consult the listed reference material to assist in determining whether a given installation complies with the applicable limits.In general the following guidelines should be observed when working in or around radio transmitter sites:-    All personnel should have electromagnetic energy awareness training.-    All personnel entering the site must be authorized.-    Obey all posted signs-    Assume all antennas are active-    Before working on antennas, notify owners and disable appropriate    transmitters.-    Maintain minimum 3 feet clearance from all antennas.-    Do not stop in front of antennas.-     Use personal RF monitors while working near antennas.-     Never operate transmitters without shields during normal operation.-     Do not operate base station antennas in equipment rooms
68P80801H45-1   1/20/2002 15EBTS System Manual - Vol 2 Base RadiosGeneral Safety Information For installations outside of the U.S., consult with the applicable governing body and standards for RF energy human exposure requirements and take necessary steps for compliance with local regulations.References:TIA/EIA TSB92 “Report on EME Evaluation for RF Cabinet Emissions Under FCC MPE Guidelines”, Global Engineering Documents: http://globl.ihs.com/FCC OET Bulletin 65 “Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields”; http://www.fcc.gov/oet/rfsaftey/.Motorola Standards and Guideline for Communications Sites, Motorola manual 68P81089E50.IEEE Recommended Practice for the Measure of Potentially Hazardous Electromagnetic Fields-- RF and Microwave, IEEE Std. C95.3-1991, Publication Sales, 445 Hoes Lane, P.O. Box 1331, Piscattaway, NJ 08855-1331IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz, IEEE C95.1-1991,
68P80801H45-1   1/20/2002 1Global Telecommunications  Solutions Sector 1301 E. Algonquin Road, Schaumburg, IL 60196 Base RadioOverviewThis chapter provides an overview of the 800/900/1500 MHz Legacy, 800 MHz Generation 2 Single Channel, 800 MHz and 900 MHz QUAD Channel Base Radios (BRs) along with  technical information.  The section topics are listed and described in Table 1. FRU Number to Kit Number Cross ReferenceSection Page DescriptionGeneration 2 Single Channel 800 MHz Base Radio Overview3 Describes  Controls and Indications, Theory of Operation, and Specifications for the 800 MHz Generation 2  Base Radio.QUAD Channel 900 MHz Base Radio Overview11 Provides  information on the 900 MHz QUAD Channel Base Radio’s Controls and Indications, Specifications and Theory of Operation.QUAD Channel 800 MHz Base Radio Overview16 Provides  information on the 800 MHz QUAD Channel Base Radio’s Controls and Indications, Specifications and Theory of Operation.Legacy Single Carrier 800 MHz Base Radio Overview21 This section  provides information on the Legacy Single Channel 800/900/1500MHz Base Radio including Controls  and Indications, Specifications and Theory of Operation.Ta ble  1 FRU Number to Kit Number Cross ReferenceDescription FRU Number Kit NumberSingle Channel 800/900/1500 MHz BRC TLN3334 CLN1469Single Channel BRC (MCI) TLN3425 CLN1472Enhanced Base Radio Controller DLN6446 CLN1653900 MHz QUAD Channel BRC DLN1203 CLF6242800 MHz QUAD Channel BRC CLN1497 CLF1560
268P80801H45-1   1/20/2002Base Radio EBTS System Manual - Vol 2 NOTEThe Single Carrier Base Radio section covers the 800 MHz, 900 MHz and 1500 MHz Legacy and 800 MHz Generation 2 versions of the Base Radio (BR).  Information is presented generally for all models.  Information that is model specific noted in the text.NOTEFor Generation 2 BR, both the 800 MHz Exciter and the 800 MHz Low Noise Exciter modules are supported subject to Table 2 on page 4.NOTEFor QUAD Channel 800 MHz BR use, all Single Carrier BR modules have undergone redesign. Therefore, Single Carrier BR modules are incompatible with the QUAD Channel 800 MHz BR. QUAD Channel 800 MHz BR modules are incompatible with the Single Carrier BR. Do not attempt to insert QUAD Channel 800 MHz BRmodules into a Single Carrier BR or Single Carrier BRmodules into a QUAD Channel 800 MHz BR.NOTEFor QUAD Channel 900 MHz BR use, all Single Carrier BR modules are incompatable with the 900 MHz QUAD Channel BR. 900 MHz QUAD Channel BR modules are incompatable with the Single Carrier BR.Do not attempt to insert QUAD Channel 900 MHz BRmodules into a Single Carrier BR or Single Carrier BRmodules into a QUAD Channel 900 MHz BR.
68P80801H45-1   1/20/2002 11EBTS System Manual - Vol 2 Base RadioQUAD Channel 900 MHz Base Radio Overview QUAD Channel 900 MHz Base Radio OverviewThe QUAD Channel 900 MHz BR provides reliable, digital BR capabilities in a compact, software-controlled design. Voice compression techniques, time division multiplexing (TDM) and multi-carrier operation provide increased channel capacity. The QUAD Channel 900 MHz BR contains the four FRUs listed below:❐QUAD Channel 900 MHz EX /Cntl❐QUAD Channel 900 MHz Power Amplifier❐QUAD Channel 800 MHz and 900 MHz Power Supply (DC)❐QUAD Channel 900 MHz Receiver  (qty. 4)The modular design of the QUAD Channel 900 MHz BR also offers increased shielding and provides easy handling. All FRUs connect to the backplane through blindmate connectors. NOTEBoth the 800 MHz QUAD and 900 MHz QUAD Base Radios use the same backplane and cardcage but call out different FCC ID numbers.Figure 2 shows the front view of the BR.EBTS282Q_900112601JNM900 QUAD CHANNEL RECEIVERQUAD CHANNEL POWER SUPPLY900 QUAD CHANNEL RECEIVER 900 QUAD CHANNEL RECEIVER900 QUAD CHANNEL RECEIVER900 QUAD CHANNEL RECEIVER900 QUAD CHANNEL RECEIVERSTATUSRESETTX4TX4TX4TX4PSEX/CNTLPAREFRX1RX2RX3RX4Figure 2  QUAD Channel 900 MHz  Base Radio (Typical)
12 68P80801H45-1   1/20/2002Base Radio EBTS System Manual - Vol 2QUAD Channel 900 MHz Base Radio Overview QUAD Channel 900 MHz  Base Radio Controls and IndicatorsPower Supply and EX / CNTL  controls and indicators monitor BR status and operating conditions, and also aid in fault isolation. The Power Supply and EX / CNTL sections of this chapter discuss controls and indicators for both modules.The Power Supply has two front panel indicators. The EX / CNTL has twelve front panel indicators. The Power Supply power switch applies power to the BR. The EX / CNTL RESET switch resets the BR. QUAD Channel 900 MHz  Base Radio Performance SpecificationsQUAD Channel 900 MHz  Base Radio General SpecificationsTable 6 lists general specifications for the BR.Table 6    QUAD Channel 900 MHz  BR General SpecificationsSpecification Value or RangeDimensions:HeightWidthDepthWeight5 EIA Rack Units (RU)19" (482.6 mm)16.75" (425 mm)85 lbs. (38.6 kg)Operating Temperature 32˚ to 104˚ F (0˚ to 40˚ C)Storage Temperature -22˚ to 140˚ F (-30˚ to 60˚ C)Rx Frequency Range:900 MHz iDEN 896 - 901 MHzTx Frequency Range:900 MHz iDEN 935 - 940 MHzTx – Rx Spacing:900 MHz iDEN 39 MHzCarrier Spacing 25 kHzCarrier Capacityaa. Multi-carrier operation must utilize adjacent, contiguous RF carriers.1, 2, 3 or 4Frequency Generation SynthesizedDigital Modulation QPSK, M-16QAM, and M-64QAMPower Supply Inputs:VDC -48 VDC (-41 to -60 VDC)Diversity Branches Up to 3
68P80801H45-1   1/20/2002 13EBTS System Manual - Vol 2 Base RadioQUAD Channel 900 MHz Base Radio Overview QUAD Channel 900 MHz  Base Radio Transmit SpecificationsTable 7 lists the BR transmit specifications.QUAD Channel 900 MHz  Base Radio Receive SpecificationsTable 8 lists the receive specifications.     Table 7    QUAD Channel 900 MHz BR Transmit Specifications  Specification Value or RangeLow average output power per carrierHigh average output power per carrierAverage Power Output:(900 MHZ) Single Carrier 5.0W 52.0W(900 MHz) Dual Carrier 2.5W 26.0W(900 MHz) Triple Carrier 1.7W 16.1W(900 MHz) QUAD Channel 1.3W 10.5WTransmit Bit Error Rate (BER) 0.01%Occupied Bandwidth 18.5 kHzFrequency Stability * 1.5 ppmRF Input Impedance 50 Ω (nom.)FCC Designation (FCC Rule Part 90):900 MHz QUAD BR ABZ89FC5798* Transmit frequency stability locks to an external site reference, which controls ultimate frequency stability to a level of 50 ppb.Table 8    QUAD Channel 900 MHz Receive Specifications Specification Value or RangeStatic Sensitivity †:900 MHz BR  -108 dBm (BER = 8%)BER Floor (BER = 0.01%) ≥ -80 dBmIF Frequencies1st IF (All bands):2nd IF:73.35 MHz (1st IF)450 kHz (2nd IF)Frequency Stability * 1.5 ppmRF Input Impedance 50 Ω (nom.)FCC Designation (FCC Rule Part 15):900 MHz BR  ABZ89FR5799† Measurement referenced from single receiver input port of BR.* Stability without site reference connected to station. Receive frequency stability locks to an external site reference, which controls ultimate frequency stability to a level of 50 ppb.
14 68P80801H45-1   1/20/2002Base Radio EBTS System Manual - Vol 2QUAD Channel 900 MHz Base Radio Overview   QUAD Channel 900 MHz  Base Radio Theory of OperationThe QUAD Channel 900 MHz  BR operates with other site controllers and equipment and must be properly terminated. The following description assumes such a configuration. Figure 6 show an overall block diagram of the QUAD Channel 900 MHz  BR.Power is applied to the DC Power inputs located on the QUAD Channel 900 MHz  BR backplane. The DC Power input is connected if -48 VDC or batteries are used in the site.Power is applied to the BR by setting the Power Supply power switch to the ON position. Upon power-up, the QUAD Channel 900 MHz  BR performs self-diagnostic tests to ensure the integrity of the unit. These tests, which include memory and Ethernet verification routines, primarily examine the EX / CNTL. After completing self-diagnostic tests, the QUAD Channel 900 MHz  BR reports alarm conditions on any of its modules to the site controller via Ethernet. Alarm conditions may also be verified locally. Local verification involves using the service computer and the STATUS port located on the front of the QUAD Channel 900 MHz  EX / CNTL.The software resident in FLASH on the EX / CNTL registers the BR with the site controller via Ethernet. After BR registration on initial power-up, the BR software  downloads via resident FLASH or Ethernet and executes from RAM. The download includes operating parameters for the QUAD Channel 900 MHz  BR. These parameters allow the QUAD Channel 900 MHz  BR to perform call processing functions. After software downloads to the BR via Ethernet, FLASH memory stores the software object. Upon future power-ups, the software object in FLASH loads into RAM for execution.The BR operates in a TDMA (Time Division Multiple Access) mode. This mode, combined with voice compression techniques, increases channel capacity by a ratio of as much as six to one. TDMA divides both the receive and transmit signals of the BR into six individual time slots. Each receive slot has a corresponding transmit slot. This pair of slots comprises a logical RF channel.
68P80801H45-1   1/20/2002 15EBTS System Manual - Vol 2 Base RadioQUAD Channel 900 MHz Base Radio Overview The BR uses diversity reception for increased coverage area and improved quality. The Receiver modules within the QUAD Channel 900 MHz  BR contain three receiver paths. Two-branch diversity sites use two Receiver paths, and three-branch diversity sites use three Receiver paths. All Receiver paths within a given Receiver module are programmed to the same receive frequency. Signals from each receiver arrive at the EX / CNTL module. This module performs a diversity combining algorithm on the signals. The resultant signal undergoes an error-correction process. Then, via Ethernet, the site controller acquires the signal, along with control information about signal destination.Two separate FRUs comprise the transmit section of the QUAD Channel 900 MHz  BR. These are the Exciter portion of the EX / CNTL and the Power Amplifier (PA). The Exciter processes commands from the CNTL, assuring transmission in the proper modulation format. Then the low-level signal enters the PA. The PA amplifies this signal to the desired output power level. The PA is a continuously keyed linear amplifier. A power control routine monitors the output power of the BR. The routine adjusts the power as necessary to maintain the proper output level.
 28 68P80801H45-1   1/20/2002 800/900/1500 MHz Base Radios EBTS System Manual - Vol 2 Base Radio Overview16.8MHz2.4MHz48MHzHost SPIHost SPI16.8MHzSTATUSPORTRS-2325 MHZEXTERNALREFERENCEETHERNET1PPS & SLOT TIMINGRX1 DATARX2 DATARX3 DATARX4 DATARx1&2Rx3&4POWER AMPLIFIER MODULETx_I Tx_QEXCITER-BASE RADIO CONTROLLERHOSTu’PSDRAMRECEIVEDSPETHERNETEEPROMFLASHPLL/VCOsTRANSMITDSPTISICTX RECLOCKBUFFERSRX SPIBASE RADIO CONTROLLER ExciterIO LATCHESRECEIVEDSPINTERFACEADDRESS DECODE,MEMORY, ADCSPI BUSLINEARDRIVERFINALLINEARAMPSCOMBINERSPLITTERRF OUTTO RFDS(TX ANTENNA)DAC VCOs/SynthsIQODCTLINEAR RFAMPLIFIERRF INRF FEEDBACKDC POWER SUPPLY MODULEINPUT FILTERSTART-UPINVERTERCIRCUITRYEXTERNALDC INPUT41 - 60 VDCCLOCKGENERATOR133 KHZ 267 KHZ133 KHZ14.2 VCONVERTER3.3 VCONVERTER+28 VDCTO BACKPLANE+14.2 VDCTO BACKPLANE+3.3 VDCTO BACKPLANEMain ConverterMIXER IF FILTERAMP, AGC ABACUSRECEIVERICLPF, AMP,FILTERMIXER IF FILTERAMP, AGC ABACUSRECEIVERICLPF, AMP,FILTERMIXER IF FILTERAMP, AGC ABACUSRECEIVERICLPF, AMP,FILTERRX INTERFACE,ADDRESS DECODE.MEMORY, DIAGNOSTICSPREAMPLIFIERSPLITTER/ BYPASSVCO SYNTHSPLITTERRF INFROM RFDS(BRANCH 2)MIXER IF FILTERAMP, AGC ABACUSRECEIVERICLPF, AMP,FILTERMIXER IF FILTERAMP, AGC ABACUSRECEIVERICLPF, AMP,FILTERMIXER IF FILTERAMP, AGC ABACUSRECEIVERICLPF, AMP,FILTERRX INTERFACE,ADDRESS DECODE.MEMORY, DIAGNOSTICSPREAMPLIFIERSPLITTER/ BYPASSVCO SYNTHSPLITTERRF INFROM RFDS(BRANCH 3)MIXER IF FILTERAMP, AGC ABACUSRECEIVERICLPF, AMP,FILTERMIXER IF FILTERAMP, AGC ABACUSRECEIVERICLPF, AMP,FILTERMIXER IF FILTERAMP, AGC ABACUSRECEIVERICLPF, AMP,FILTERRX INTERFACE,ADDRESS DECODE.MEMORY, DIAGNOSTICSPREAMPLIFIERSPLITTER/ BYPASSVCO SYNTHSPLITTERRF INFROM RFDS(BRANCH 1)RECEIVER 2RECEIVER 3RECEIVER 4RECEIVER 1MIXERIF FILTERAMP, AGCABACUSRECEIVERIC LPF, AMP,FILTERMIXERIF FILTERAMP, AGCABACUSRECEIVERIC LPF, AMP,FILTERMIXERIF FILTERAMP, AGCABACUSRECEIVERIC LPF, AMP,FILTERRX INTERFACE,ADDRESS DECODE.MEMORY, DIAGNOSTICSPREAMPLIFIERSPLITTER/ BYPASSVCO SYNTHSPLITTERSPI BUSSPI BUSSPI BUSADDRESS DECODE,MEMORY, ADCQUAD RX IN DISTRIBUTION16.8MHzFigure 6 800 and 900 MHZ QUAD Channel Base Radio Functional Block DiagramRECEIVER 4
68P80801H45-1 1/20/2002 1Global Telecommunications  Solutions Sector 1301 E. Algonquin Road, Schaumburg, IL 60196 Base Radio ControllersOverviewThis chapter provides information on Base Radio Controllers (BRCs):FRU Number to Kit Number Cross ReferenceBase Radio Controller (BRC) Field Replaceable Units (FRUs) are available for the iDEN EBTS. The FRU contains the BRC kit and required packaging. Table 1 provides a cross reference between BRC FRU numbers and kit numbers. Chapter Topic Page DescriptionEnhanced Base Radio Controller 2 Includes information on the Enhanced Base Radio Controller’s Controls and Indications and Theory of Operation900 MHz QUAD Channel Base Radio Controller15 Provides an 900 MHz QUAD Channel BRC Controls and Indications as well as the controller’s Theory of Operation800 MHz QUAD Channel Base Radio Controller25 Provides an overview, 800 MHz QUAD Channel BRC Controls and Indications as well as the controller’s Theory of Operation800/900/1500 MHz Legacy Base Radio Controller35 Provides an overview, outline of controls and indications as well as the controller’s Theory of OperationTable 1    FRU Number to Kit Number Cross ReferenceDescription FRU Number Kit NumberSingle Channel 800/900/1500 MHz Base Radio ControllerTLN3334 CLN1469Single Channel Base Radio Controller(1500 MHz MCI)TLN3425 CLN1472Enhanced Base Radio Controller DLN6446 CLN1653QUAD Channel 900 MHz Exciter/BR Controller DLN1203QUAD Channel 800 MHz Exciter/BR Controller  CLN1497 CLF1560
68P80801H45-1   1/20/2002 15EBTS System Manual - Vol 2 Base Radio Controllers900 MHz QUAD Channel Base Radio Controller 900 MHz QUAD Channel Base Radio Controller900 MHz QUAD Channel Base Radio Controller OverviewThe Base Radio Controller (BRC) provides signal processing and operational control for Base Radio modules. The BRC module consists of a printed circuit board, a slide-in housing, and associated hardware.The BRC memory contains the operating software and codeplug. The software defines BR operating parameters, such as output power and operating frequency. The BRC connects to the Base Radio backplane with one 168-pin FutureBus+ connector and one blindmate RF connector. Two Torx screws secure the BRC in the Base Radio chassis. Figure 3 shows a top view of the EX/CNTL (model CLF1560) with the cover removed.Figure 3 900 MHz QUAD Channel Base Radio Controller, version DLN1203 (with cover removed)
16 68P80801H45-1   1/20/2002Base Radio Controllers EBTS System Manual - Vol 2900 MHz QUAD Channel Base Radio Controller 900 MHz QUAD Channel Base Radio Controller Controls and IndicatorsThe BRC monitors the functions of other Base Radio modules. The LEDs on the front panel indicate the status of BRC-monitored modules. All LEDs on the BRC front panel normally flash three times upon initial power-up. A RESET switch allows a manual reset of the Base Radio. Figure 4 shows the front panel of the BRC.IndicatorsTable 7 lists and describes the BRC LEDs. Table 7    900 MHz QUAD Channel BR Controller Indicators  LED Color ModuleMonitoredCondition IndicationsPS Red Power SupplySolid (on) FRU failure indication - Power Supply has a major alarm, and is out of serviceFlashing (on) Power Supply has a minor alarm, and may be operating at reduced performanceOff Power Supply is operating normally (no alarms)EXBRC Red Controller/ExciterSolid (on) FRU failure indication - Controller/Exciter has a major alarm, and is out of service (Note: Upon power-up of the BR, this LED indicates a failed mode until BR software achieves a known state of operation.)Flashing (on) Controller/Exciter has a minor alarm, and may be operating at reduced performanceOff Controller/Exciter is operating normally (no alarms)PA Red Power AmplifierSolid (on) FRU failure indication - PA has a major alarm, and is out of serviceFlashing (on) PA has a minor alarm, and may be operating at reduced performanceOff PA is operating normally (no alarms)QUAD CHANNEL EX/CNTLSTATUSRESETTX4TX4TX4TX4PSEX/CNTLPAREFRX1RX2RX3RX4EBTS316Q013001JNMFigure 4 900 MHz QUAD Channel BR Controller (Front View)
68P80801H45-1   1/20/2002 17EBTS System Manual - Vol 2 Base Radio Controllers900 MHz QUAD Channel Base Radio Controller ControlsTable 8 lists the controls and descriptions. STATUS ConnectorTable 9 the pin-outs for the STATUS connector. REF Red Controller Station ReferenceSolid (on) FRU failure indication - Controller Station Reference has a major alarm, and is out of serviceFlashing (on) BRC has a minor alarm, and may be operating in a marginal regionOff BRC is operating normally (no alarms)RX1RX2RX3RX4Red Receiver #1, #2, #3, or #4Solid (on) FRU failure indication - Receiver (#1, #2, #3 or #4) has a major alarm, and is out of serviceFlashing (on) Receiver (#1, #2, #3 or #4) has a minor alarm, and may be operating at reduced performanceOff Receiver (#1, #2, #3 or #4) is operating normally (no alarms)TX1 Green BR Solid (on) Station Transmit Carrier #1 is keyedFlashing (on) Station Transmit Carrier #1 is not keyedOff Station is out of service, or power is removedTX2 Green BR Solid (on) Station Transmit Carrier #2 is keyedFlashing (on) Station Transmit Carrier #2 is not keyedOff Station is out of service, or power is removedTX3 Green BR Solid (on) Station Transmit Carrier #3 is keyedFlashing (on) Station Transmit Carrier #3 is not keyedOff Station is out of service, or power is removedTX4 Green BR Solid (on) Station Transmit Carrier #4 is keyedFlashing (on) Station Transmit Carrier #4 is not keyedOff Station is out of service, or power is removedTable 7    900 MHz QUAD Channel BR Controller Indicators  (Continued)LED Color ModuleMonitoredCondition Indications
18 68P80801H45-1   1/20/2002Base Radio Controllers EBTS System Manual - Vol 2900 MHz QUAD Channel Base Radio Controller 900 MHz QUAD Channel Base Radio Controller Theory of OperationTable 10 briefly describes the BRC circuitry. Figure 13 is a functional block diagram of the BRC. Host MicroprocessorThe host microprocessor is the main controller for the BR. The processor operates at a 50-MHz clock speed. The processor controls Base Radio operation according to station software in memory. Station software resides in FLASH memory. For normal operation, the system transfers this software to non-volatile memory. An EEPROM contains the station codeplug.NOTEAt BR power-up, the EXBRC LED indicates a major alarm. This indication continues until BR software achieves a predetermined state of operation. Afterward, the software turns off the EXBRC LED.Table 8    900 MHz QUAD Channel BR Controller Controls Control DescriptionRESET Switch A push-button switch used to manually reset the BR.STATUS connectorA 9-pin connector used for connection of a service computer, providing a convenient means for testing and configuring.Table 9    Pin-outs for the STATUS ConnectorPin-out Signal1 not used2 TXD3 RXD4 not used5 GND6 not used7 not used8 not used9 not used
68P80801H45-1   1/20/2002 19EBTS System Manual - Vol 2 Base Radio Controllers900 MHz QUAD Channel Base Radio Controller Table 10    900 MHz QUAD Channel BR Controller CircuitryCircuit DescriptionHost Microprocessor Contains integrated circuits that comprise the central controller of the BRC and stationNon-Volatile Memory Consists of: • FLASH containing the station operating software• EEPROM containing the station codeplug dataVolatile Memory Contains SDRAM to store station software used to execute commands.Ethernet Interface Provides the BRC with a 10Base2 Ethernet communication port to network both control and compressed voice dataRS-232 Interface Provides the BRC with an RS-232 serial interfaceDigital Signal Processors Performs high-speed modulation/demodulation of compressed audio and signaling dataTISIC Contains integrated circuits that provide timing reference signals for the stationTX Reclock Contains integrated circuits that provide highly stable, reclocked transmit signals and peripheral transmit logicRX DSP SPI Contains integrated circuits that provide DSP SPI capability and peripheral receive logicStation Reference Circuitry Generates the 16.8 MHz and 48 MHz reference signals used throughout the stationInput Ports  Contains 16 signal input ports that receive miscellaneous inputs from the BROutput Ports Contains 40 signal output ports, providing a path for sending miscellaneous control signals to circuits throughout the BRRemote Station Shutdown Provides software control to cycle power on the BR
20 68P80801H45-1   1/20/2002Base Radio Controllers EBTS System Manual - Vol 2900 MHz QUAD Channel Base Radio Controller Serial Communication BusesThe microprocessor provides a general-purpose SMC serial management controller bus.The SMC serial communications bus is an asynchronous RS-232 interface with no hardware handshake capability. The BRC front panel includes a nine-pin, D-type connector. This connector provides a port where service personnel may connect a service computer. Service personnel can perform programming and maintenance tasks via Man-Machine Interface (MMI) commands. The interface between the SMC port and the front- panel STATUS connector is via EIA-232 Bus Receivers and Drivers.Host ProcessorThe microprocessor incorporates 4k bytes of instruction cache and 4k bytes of data cache that significantly enhance processor performance.The microprocessor has a 32-line address bus. The processor uses this bus to access non-volatile memory and SDRAM memory. Via memory mapping, the processor also uses this bus to control other BRC circuitry. The microprocessor uses its Chip Select capability to decode addresses and assert an output signal. The eight chip-select signals select non-volatile memory, SDRAM memory, input ports, output ports, and DSPs.The Host processor... ❐Provides serial communications between the Host Microprocessor and other Base Radio modules.❐Provides condition signals necessary to access SDRAM.❐Accepts interrupt signals from BRC circuits (such as DSPs). ❐Organizes the interrupts, based on hardware-defined priority ranking.❐The Host supports several internal interrupts from its Communications Processor Module. These interrupts allow efficient use of peripheral interfaces.❐The Host supports 10 Mbps Ethernet/IEEE 802.3. ❐Provides a 32-line data bus transfers data to and from BRC SDRAM and other BRC circuitry. Buffers on this data bus allow transfers to and from non-volatile memory, general input and output ports and DSPs.Non-Volatile MemoryBase Radio software resides in 2M x 32 bits of FLASH memory. The Host Microprocessor addresses the FLASH memory with 20 of the host address bus’ 32 lines. The host accesses FLASH data over the 32-line host data bus. A host-operated chip-select line provides control signals for these transactions. The FLASH contains the operating system and application code. The system stores application code in FLASH for fast recovery from reset conditions. Application code transfers from network or site controllers may occur in a
68P80801H45-1   1/20/2002 21EBTS System Manual - Vol 2 Base Radio Controllers900 MHz QUAD Channel Base Radio Controller background mode. Background mode transfers allow the station to remain operational during new code upgrades.The data that determines the station personality resides in a 32K x eight bit codeplug EEPROM. The microprocessor addresses the EEPROM with 15 of the host address bus’ 32 lines. The host accesses EEPROM data with eight of the data bus’ 32 lines. A host-operated chip-select line provides control signals for these transactions. During the manufacturing process, the factory programs the codeplug’s default data. The BRC must download field programming data from network and site controllers. This data includes operating frequencies and output power level. The station permits adjustment of many station parameters, but the station does not store these adjustments. Refer to the Software Commands chapter for additional information.Volatile MemoryEach BRC contains 8MB x 32 bits of SDRAM. The BRC downloads station software code into SDRAM for station use. SDRAM also provides short-term storage for data generated and required during normal operation. SDRAM is volatile memory. A loss of power or system reset destroys SDRAM data. The system performs read and write operations over the Host Address and Data buses. These operations involve column and row select lines under control of the Host processor’s DRAM controller. The Host address bus and column row signals sequentially refresh SDRAM memory locations.Ethernet InterfaceThe Host processor’s Communications Processor Module (CPM) provides the Local Area Network (LAN) Controller for the Ethernet Interface. The LAN function implements the CSMA/CD access method, which supports the IEEE 802.3 10Base2 standard. The LAN coprocessor supports all IEEE 802.3 Medium Access Control, including the following: ❐framing ❐preamble generation ❐stripping❐source address generation❐destination address checkingThe PCM LAN receives commands from the CPU. The Ethernet Serial Interface works directly with the CPM LAN to perform the following major functions:❐10 MHz transmit clock generation (obtained by dividing the 20 MHz signal provided by on-board crystal)❐Manchester encoding/decoding of frames
22 68P80801H45-1   1/20/2002Base Radio Controllers EBTS System Manual - Vol 2900 MHz QUAD Channel Base Radio Controller ❐electrical interface to the Ethernet transceiverAn isolation transformer provides high-voltage protection. The transformer also isolates the Ethernet Serial Interface (ESI) and the transceiver. The pulse transformer has the following characteristics:❐Minimum inductance of 75 µH❐2000 V isolation between primary and secondary windings❐1:1 Pulse Transformer The Coaxial Transceiver Interface (CTI) is a coaxial cable line driver and receiver for the Ethernet. CTI provides a 10Base2 connection via a coaxial connector on the board. This device minimizes the number of external components necessary for Ethernet operations. A DC/DC converter provides a constant voltage of -9 Vdc for the CTI from a 3.3 Vdc source. The CTI performs the following functions:❐Receives and transmits data to the Ethernet coaxial connection❐Reports any collision that it detects on the coaxial connection❐Disables the transmitter when packets are longer than the legal length (Jabber Timer)Digital Signal ProcessorsThe BRC includes two Receive Digital Signal Processors (RXDSPs) and a Transmit Digital Signal Processor (TXDSP). These DSPs and related circuitry process compressed station transmit and receive audio or data. The related circuitry includes the TDMA Infrastructure Support IC (TISIC) and the TISIC Interface Circuitry. The DSPs only accept input and output signals in digitized form.The RXDSP inputs are digitized receiver signals. The TXDSP outputs are digitized voice audio and data (modulation signals). These signals pass from the DSP to the Exciter portion of the EXBRC. DSPs communicate with the Microprocessor via an eight-bit, host data bus on the host processor side. For all DSPs, interrupts drive communication with the host.The RXDSPs operate from an external 16.8 MHz clock, provided by the local station reference. The RXDSP internal operating clock signal is 150MHz, produced by an internal Phase-Locked Loop (PLL). The RXDSPs accept digitized signals from the receivers through Enhanced Synchronous Serial Interface (ESSI) ports. Each of two ESSI ports on a RXDSP supports a single carrier (single receiver) digital data input. The DSP circuitry includes two RXDSPs. These allow processing of up to four carriers (four receivers).The RXDSP accesses its DSP program and signal-processing algorithms in 128k words of internal memory. The RXDSPs communicate with the host bus over an 8-bit interface. Each RXDSP provides serial communications to its respective receiver module for receiver control via a Serial Peripheral Interface (SPI). The SPI is a
68P80801H45-1   1/20/2002 23EBTS System Manual - Vol 2 Base Radio Controllers900 MHz QUAD Channel Base Radio Controller parallel-to-serial conversion circuit, connected to the RXDSP data bus. Each RXDSP communicates to two receive modules through this interface.Additionally, a serial control path connects the two RXDSPs and the TXDSP. The Synchronous Communications Interface (SCI) port facilitates this serial control path. For initialization and control purposes, one RXDSP connects to the TISIC device.The TXDSP operates at an external clock speed of 16.8 MHz, provided by the EXBRC local station reference. The TXDSP internal operating clock is 150MHz, produced by an internal Phase Lock Loop (PLL). The TXDSP sends up to four carriers of digitized signal to the EX11 exciter. The exciter converts the digital signal to analog. Also at the exciter, a highly stable clock reclocks the digital data. Reclocking enhances transmit signal integrity. Two framed and synchronized data streams result. One data stream is I-data, and the other is the Q-data stream.The TXDSP contains its own, internal address and data memory. The TXDSP can store 128k words of DSP program and data memory. An eight-bit interface handles TXDSP-to-host bus communications.TISICThe TISIC controls internal DSP operations. This circuit provides the following functions:❐For initialization and control, interfaces with one RXDSP via the DSP address and data buses.❐Accepts a 16.8 MHz signal from Station Reference Circuitry.❐Accepts a 5 MHz signal, modulated with one pulse per second (1 PPS) from the site reference. ❐Demodulates the 1 PPS ❐Outputs a 1 PPS signal and a windowed version of this signal for network timing alignment.❐Outputs a 2.4 MHz reference signal used by the Exciter.❐Generates 15 ms and 7.5 ms ticks. (These ticks synchronize to the 1 PPS time mark. The system decodes the time mark from the site reference. Then the system routes the reference to the TXDSP and RXDSPs.)Station Reference CircuitryThe Station Reference Circuitry is a phase-locked loop (PLL). This PLL consists of a high-stability, Voltage-Controlled, Crystal Oscillator (VCXO) and a PLL IC. GPS output from the iSC connects to the 5 MHz/1 PPS BNC connector on the BR backplane. Wiring at this connector routes signals to EXBRC station reference circuitry. The PLL compares the 5 MHz reference frequency to the 16.8 MHz VCXO output. Then the PLL generates a DC correction voltage. The PLL applies this correction voltage to the VCO through an analog gate. The analog gate closes when three
24 68P80801H45-1   1/20/2002Base Radio Controllers EBTS System Manual - Vol 2900 MHz QUAD Channel Base Radio Controller conditions coexist: (1) The 5 MHz tests stable. (2) The PLL IC is programmed. (3) Two PLL oscillator and reference signal output alignments occur. When the gate enables, the control voltage from the PLL can adjust the high-stability VCXO frequency. The adjustment can achieve a stability nearly equivalent to that of the external, 5 MHz frequency reference.The correction voltage from the PLL continuously adjusts the VXCO frequency. The VXCO outputs a 16.8 MHz clock signal. The circuit applies this clock signal to the receiver, 48 MHz reference and TISIC. The receivers use the 16.8MHz as the clock input and synthesizer reference.The 48 MHz EXBRC synthesizer uses the 16.8 MHz as its synthesizer reference. The 48 MHz synthesizer output is the clock input for the TXDSP I and Q data reclock circuitry.The TISIC divides the 16.8 MHz signal by seven, and outputs a 2.4 MHz signal. This output signal then becomes the 2.4 MHz reference for the Exciter.Input PortsOne general-purpose input register provides for BRC and station circuit input signals. The register has 16 input ports. The Host Data Bus conveys input register data to the Host Microprocessor. Typical inputs include 16.8 and 48 MHz Station Reference Circuitry status outputs and reset status outputs.Output PortsTwo general-purpose output registers distribute control signals from the Host Microprocessor to the BRC and station circuitry. One register has 32 output ports and the other register has 8 output ports. Control signal distribution occurs over the backplane. The Host Data Bus drives the output ports’ latched outputs. Typical control signals include front-panel LED signals and SPI peripheral enable and address lines.Remote Station ShutdownThe BRC contains power supply shutdown circuitry. This circuitry can send a shutdown pulse to the Base Radio Power Supply. BRC software generates the shutdown control pulse. After receiving a shutdown pulse, the power supply turns off BR power. Shut down power sources include 3.3, 28.6 and 14.2 Vdc sources throughout the BR. Due to charges retained by BR storage elements, power supply voltages may not reach zero. The shutdown only assures that the host processor enters a power-on-reset state. A remote site uses the shutdown function to perform a hard reset of all BR modules.
 68P80801H45-1   1/20/2002 45 EBTS System Manual - Vol 2 800/900/1500 MHz Base Radios Base Radio Controller  ETHERNETSERIALINTERFACEISOLATIONTRANSFORMER TRANSCEIVERHOST BUFFERED DATA BUSHOST ADDRESS BUSHOST BUFFERED DATA BUSHOST ADDRESS BUSHOST DATA BUSDRAM ADDRESSMULTIPLEXERCOLUMN/ROWSELECTDRAMCOLUMNADDRESSDRAMROWADDRESS16.5 MHZ CLKSERIAL COMMUNICATIONS BUSSERIAL COMMUNICATIONS BUSROWSELECT(RAS*)COLSELECT(CAS*)DRAMADDRESSHOSTGLUEASIC33 MHZTIMINGCIRCUITRYBUFFERSEPROM512K X 88K X 8EEPROMCODEPLUG32K X 8SRAM32K X 8SRAMA1-A11A10-A22A1-A19A1-A19A1-A15HOSTADDRESSA1-A1848STATUS PORT(9 PIN D CONNECTORON BRC FRONT PANEL)RS-232 PORT(9 PIN D CONNECTORON BACKPLANE)EIA-232BUSRECEIVERS/DRIVERS48EPROM512K X 8BUFFERSSPI BUSSPI BUSTO/FROMSTATION MODULES3HOST ADDRESS BUSNON-VOLATILE MEMORYHOSTMICRO-PROCESSORHOST MICROPROCESSOR / HOST ASICHOSTADDRESS1-23EIA-232BUSRECEIVERS/DRIVERSDRAM MEMORYBUFFERSVARIOUS INPUTSFROM BRC &STATION CIRCUITRYINPUT/OUTPUT PORTS CIRCUITRYI/O PORT P0 INHOST DATA BUSI/O PORT P0 OUTI/O PORT P1 OUTI/O PORT P2 OUTVARIOUSCONTROLLINES TO BRC &STATIONCIRCUITRYFROM HOSTMICROPROCESSORI/O PORT P1 INBUFFERSBUFFERS1616161616REMOTE STATIONSHUTDOWN CIRCUITRYSHUTDOWN(TO POWERSUPPLY)28VI/O PORTP2 OUTFRONT PANEL LEDSLED CONTROLLINES(P/O I/O PORTP0 OUT)BASERADIOPOWERSUPPLY EXCITER PA CTL R1 R2 R38ETHERNET INTERFACECDRXTXCLSNRCVTRMTFROMHOSTMICROPROCESSORADDR BUSDATA BUSCOPROCESSORADDR BUSCOPROCESSORDATA BUS10BASE2COAXETHERNETSERIALINTERFACEHOSTINTERFACEETHERNETCOPROCESSOR(82596DX)AEBTS286010397SND0-D15LANIICSHUTDOWNCIRCUITRYA1-A15A1-A15D0-D15D0-D7D0-D15D0-D15VCC RESET SWITCH(FRONT PANEL)DRAM1M X 16A2-A23Base Radio ControllerFigure 10 800/900 MHz Base Radio Controller Functional Block Diagram(Sheet 1 of 2)
 46 68P80801H45-1   1/20/2002 800/900/1500 MHz Base Radios EBTS System Manual - Vol 2 Base Radio Controller  Base Radio ControllerFunctional Block DiagramModel TLN3424(Includes Front Panel Board)HOST BUFFERED DATA BUSHOST ADDRESS BUSHOST BUFFERED DATA BUSHOST ADDRESS BUSHOST DATA BUSDRAM ADDRESSMULTIPLEXERCOLUMN/ROWSELECTDRAMCOLUMNADDRESSDRAMROWADDRESS16.5 MHZ CLKSERIAL COMMUNICATIONS BUS (SCC2)SERIAL COMMUNICATIONS BUS (SCC3)ROWSELECT(RAS*)COLSELECT(CAS*)COLSELECT(CAS*)ROWSELECT(RAS*)DRAMADDRESSDRAMADDRESSHOSTASIC(U509)33 MHZTIMINGCIRCUITRY(Y500)BUFFERS(U107 - U110)EPROM256K X 8(U802)8K X 8EEPROMCODEPLUG(U800)8K X 8SRAM(U803)8K X 8SRAM(U804)A1-A11A10-A22A1-A18A1-A18A1-A15HOSTADDRESSA1-A2348STATUS(9 PIN D CONNECTORON BRC FRONT PANEL)RS232(9 PIN D CONNECTORON BACKPLANE)EIA-232BUSRECEIVERS/DRIVERS(U901, U902)EPROM256K X 8(U801)SPI BUSSPI BUSTO/FROMSTATION MODULES3HOST ADDRESS BUSNON-VOLATILE MEMORYHOSTMICRO-PROCESSOR(U701)HOST MICROPROCESSOR / HOST ASICDRAM1M X 8(U114)DRAM1M X 8(U114)HOSTADDRESS1-23EIA-232BUSRECEIVERS/DRIVERS(U900)DYNAMIC RAMVARIOUS INPUTSFROM BRC &STATION CIRCUITRYINPUT/OUTPUT PORTS CIRCUITRYI/O PORT P0 INHOST DATA BUS I/O PORT P0 OUTI/O PORT P1 OUTI/O PORT P2 OUTI/O PORT P3 OUTVARIOUSCONTROLLINES TO BRC &STATIONCIRCUITRYFROM HOSTMICROPROCESSORI/O PORT P1 INLATCHES(U602 - U605,U608 - U611)BUFFERS(U600, U601,U606, U607)161616161616REMOTE STATIONSHUTDOWN CIRCUITRYSHUTDOWN(TO POWERSUPPLY)28VI/O PORTP3 OUTFRONT PANEL LEDS (Part of TRN7769)LED CONTROLLINES(P/O I/O PORTP0 OUT)BASERADIOPOWERSUPPLY EXCITER PA BRC RX1 RX2 RX38ETHERNET INTERFACECDRXTXCLSNRCVTRMTFROMHOSTMICROPROCESSORADDR BUSDATA BUSCOPROCESSORADDR BUSCOPROCESSORDATA BUS10BASE2COAXETHERNETSERIALINTERFACE82596DXETHERNETCOPROCESSOR(U408)ETHERNETSERIALINTERFACE(U1308)TRANSCEIVER(U1311)AHOSTINTERFACE(U404 - U406)ISOLATIONTRANSFORMER(T100)SHUTDOWNCIRCUITRY(U3)BUFFERS(U108 - U110)BUFFERS(U108 - U110)DC/DCCONVERTER(U1310)5 VDC-9 VDC231620 MHZTIMINGCIRCUIT(Y1300)XMT CLK(10 MHZ)A1-A13A1-A1369STATIC RAMFigure 10 800/900 MHz QUAD Channel Base Radio Functional Block Diagram Sheet 2 of 2)
 49 68P80801H45-1   1/20/2002 800/900/1500 MHz Base Radios EBTS System Manual - Vol 2 Base Radio Controller  SPIBUSPHASEDETECTION/FILTERINGHIGHSTABILITYVCXO48 MHZ16.8MHZQUAD Channel BaseRadio ControllerFunctional Block DiagramFigure 13 800 and 900 MHz QUAD Channel Base Radio Controller Functional Block Diagram (Sheet 1 of 2)POWERSUPPLY EXCITER/CONTROL PA REF RX1 RX2 RX3 RX4 TX1 TX2 TX3 TX4P0 OUTLEDCONTROLLINESHOSTLATCH12FRONT PANEL LEDS REMOTE STATION3.3VP0_OUTSHUTDOWNCIRCUITRYSHUTDOWN(TO POWERSUPPLY)SHUTDOWN CIRCUITRYSYNTHESIZERIC / CIRCUITRY5MHZ_1PPSBASE RADIOINPUTHIGHSTABILITYVCXOPHASEDETECTION/FILTERING/CONTROLSTEARINGLINEDISCONNECT/CONNECTCONTROLGATINGSPIBUS16.8 MHZSYNTHESIZERIC / CIRCUITRYSTEARINGLINESTATION REFERENCE CIRCUITRYTRANSMIT REFERENCE CIRCUITRY5MHZ1PPS
 50 68P80801H45-1   1/20/2002 800/900/1500 MHz Base Radios EBTS System Manual - Vol 2 Base Radio Controller  QUAD Channel Base Radio ControllerFunctional Block DiagramFigure 14800 and 900 MHz QUAD Channel Base Radio Controller Functional Block Diagram (Sheet 2 of 2)HOSTMICRO-ETHERNETSERIALINTERFACE TRANS-CDRCV RXTRMT TXCLSN10BASE2COAXETHERNETSERIALINTERFACECEIVERISOLATIONTRANSFORMERPROCESSORSCC18SDRAM4M x 16SDRAM4M x 16SDRAM4M x 16SDRAM4M x 16GPLA0, A[8,9,17,18,20:29],RAS,CAS,WECS2CS3D[0:31]D[0:15]D[16:31]D[0:15]D[16:31]BUFFERBUFFERBUFFERBUFFERBUFFERBUFFERD[0:31]D[0:7]A[10:31]MA[21:0]DSP_D[31:24]A[0:7]DSP_A[31:24]MD[31:0]EIA-232BUSRECEIVERS/DRIVERS2STATUS PORT(9 PIN D CONNECTORON BRC FRONT PANEL)2BUFFER33SPI BUS TO/FROM STATION MODULESFLASH1M x 16FLASH1M x 16FLASH1M x 16FLASH1M x 16CS0CS1 MD[0:15]MD[16:31]MD[0:15]MD[16:31]1616161616 161616MA[2:21]MA[2:21]EEPROM32k x 8MD[24:31]MA[0:14]CS4P1_OUTLATCHP0_OUTLATCHMD[0:32]MD[24:31]P0_INBUFFERMD[16,17,20-24,28-31]STATUS BUSFROMSTATION MODULESP0_IN8CONTROL BUSTOSTATION MODULESP0_OUT/P1_OUT328TRANSMITDIGITALSIGNALPROCESSOR(TX DSP)SINGLE ENDTO DIFFERENTIALTRANSMITCLOCK ANDFRAME SYNCHCIRCUITRYI/Q DATA SERIAL DATATO EXCITERDIFFERENTIALTO SINGLE ENDRX1 SERIAL DATARECEIVEDIGITALSIGNALPROCESSOR(RX DSP 1)RECEIVEDIGITALSIGNALPROCESSOR(RX DSP 2)TISICA[0:5]D[0, 8:23]PARALLELTO SERIALCIRCUITRYD[16:23]D[16:23]D[0, 23]SPI BUS TORECEIVER 1 & 2SPI BUS TORECEIVER 3 & 42.4 MHz1 PPS TIMING, CONTROL/ SLOT TIMING/RESETNETWORKEDSCI16.8MHZ48 MHZSPIBUSSPIBUSEXCITERSPICONTROLDSP SPISPI BUSTO EXCITERDIGITAL SIGNAL PROCESSING CIRCUITRYDIGITAL SIGNAL PROCESSING CIRCUITRYDIFFERENTIALTO SINGLE ENDDIFFERENTIALTO SINGLE ENDDIFFERENTIALTO SINGLE END50 MHZCLOCKFRONT PANELRESETDRAM MEMORYETHERNET INTERFACENON-VOLATILE MEMORY EXPANDED STATUS INPUTAND OUTPUT CONTROL CIRCUITRYEXTENDED HOSTBUS BUFFERS40TO EXCITER5MHZ1PPSRX2 SERIAL DATARX3 SERIAL DATARX4 SERIAL DATAHOST ADDRESS BUSHOST DATA BUSHOST BUFFERED DATA BUSHOST BUFFERED ADDRESS BUSHOST-DSP BUFFERED DATA BUSHOST-DSP BUFFERED ADDRESS BUSSERIAL MANAGEMENT CONTROLLER (SMC2)SERIAL PERIPHERAL INTERFACE
68P80801H45-1   1/20/2002 1EBTS System Manual - Vol 2 Base Radio Exciter Base Radio ExciterOverviewThis chapter provides technical information for the Exciter (EX).  FRU Number to Kit Number Cross ReferenceExciter Field Replaceable Units (FRUs) are available for the iDEN EBTS. The FRU contains the Exciter kit and required packaging. Table 1 provides a cross reference between Exciter FRU numbers and kit numbers. Section Page Description800 Legacy MHz Exciter – TLN3337; 900 MHz Exciter – CLN1357; 1500 MHz Exciter – TLN34282 Describes the functions and characteristics of the Exciter module for the single channel Base Radio (BR).Low Noise 800 MHz Exciter 7 Describes the functions and characteristics of the Exciter module for the Low Noise Exciter for the Generation 2 Base Radio (Gen2 BR).QUAD Channel 900 MHz Exciter11 Describes the functions and characters of the 900 MHz QUAD Channel Base Radio (BR)QUAD Channel 800 MHz Exciter15 Describes the functions and characteristics of the Exciter module for the 800 MHz QUAD channel Base Radio (BR).Table 1    FRU Number to Kit Number Cross ReferenceDescription FRU Number Kit NumberSingle Channel Exciter (800 MHz) TLN3337 CLF1490Single Channel Exciter (900 MHz) CLN1357 CLF1500Single Channel Exciter (1500 MHz) TLN3428 CTX1120QUAD Channel 900 MHz Exciter/Base Radio Controller)CLN1497 CLF6452QUAD Channel 800 MHz Exciter/Base Radio Controller CLN1497 CLF1560LNODCT (Low Noise Offset Direct Conversion Transmit) Exciter (800 MHz)TLN3337 CLF1789
68P80801H45-1   1/20/2002 11EBTS System Manual - Vol 2 Base Radio ExciterQUAD Channel 900 MHz Exciter QUAD Channel 900 MHz Exciter QUAD Channel 900 MHz Exciter OverviewThe Exciter and the Power Amplifier (PA) provide the transmitter functions of the QUAD Channel 900 MHz Base Radio.  The Exciter module consists of a printed circuit board, a slide in housing, and associated hardware. The BRC shares the printed circuit board and housing.The Exciter connects to the Base Radio backplane through a 168-pin connector and two blindmate RF connectors. Controller and exciter circuitry also interconnect on the Exciter/Controller module. Two Torx screws on the front of the Exciter secure it to the chassis. An LED identifies the Exciter’s operational condition, as described in the manual’s Controller section.  The Base Radio section of the manual provides specifications for transmitter circuitry. This information includes data on the Exciter and PAs.Figures 5 shows the Exciter with the cover removed.Figure 4 900 MHz QUAD Channel Exciter (with cover removed)
12 68P80801H45-1   1/20/2002Base Radio Exciter EBTS System Manual - Vol 2QUAD Channel 900 MHz Exciter 900 MHz QUAD Channel Exciter Theory of OperationTable 4 describes the basic circuitry of the Exciter. Figures 9 show the QUAD Carrier Exciter’s functional block diagram.Memory CircuitryThe memory circuitry is an EEPROM on the Controller portion of the Exciter/Controller module.  The Controller performs memory read and write operations over the parallel bus.  The memory device stores the following data...❐kit number❐revision number❐module specific scaling and correction factors❐serial number❐free form information (scratch pad)A/D Converter CircuitryAnalog signals from various areas throughout the Exciter board enter the A/D converter (A/DC).  The A/DC converts these analog signals to digital form. Upon Table 4    900 MHz Exciter Circuitry Circuit DescriptionLNODCT IC • Up-converts baseband data to the transmit frequency• Down-converts the PA feedback signal to baseband• Uses a baseband Cartesian feedback loop system, necessary to obtain linearity from the transmitter and avoid splattering power into adjacent channels• Performs training functions for proper linearization of the transmitterMemory & A/D Converter Serves as the main interface between the synthesizer, Tranlin IC, A/D, and EEPROM on the Exciter, and the BRC via the SPI busFrequency Synthesizer Circuitry• Consists of a phase-locked loop and VCO• Provides a LO signal to the LNODCT IC for the second up-conversion and first down-conversion of the feedback signal from the PA1025 MHz VCO (900 MHz BR) Provides a LO signal to the LNODCT IC, for up-conversion to the transmit frequency90.3 MHz VCO (900 MHz BR) Provides a LO signal to LNODCT IC, for the up-conversion and for the down-conversion of the feedback signal. The mixed output becomes the LO signal for Transmit signal up- and down- conversionRegulator Circuitry Provides a regulated voltage to various ICs and RF devices located on the ExciterLinear RF amplifier Stages Amplifies the RF signal from the Exciter IC to an appropriate level for input to the PA
68P80801H45-1   1/20/2002 13EBTS System Manual - Vol 2 Base Radio ExciterQUAD Channel 900 MHz Exciter request of the BRC, A/DC output signals enter the BRC via SPI lines. The Controller periodically monitors all signals.Some of the monitored signals include amplifier bias and synthesizer signals. Low Noise Offset Direct Conversion Transmit (LNODCT) IC CircuitryThe Low Noise IC is a main interface between the Exciter and BRC. The BRC’s Digital Signal Processor (DSP) sends digitized signals (baseband data) to the Exciter over the DSP data bus.The differential data clock signal serves as a 2.4 MHz reference signal to the Low Noise IC’s internal synthesizer.  The Low Noise IC compares the reference signal with the outputs of Voltage Controlled Oscillators (VCOs). The Low Noise IC might sense that a VCO’s output is out of phase or off-frequency. If so, then the Low Noise IC sends correction pulses to the VCO. The pulses adjust VCO output, thereby matching phase and frequency with the reference. The Low Noise IC up-converts baseband data from the BRC to the transmit frequency. The Low Noise IC also down-converts the Transmit signal from the Power Amplifier to baseband data for cartesian feedback linearization.The BRC uses the Serial Peripheral Interface (SPI) bus to communicate with the Low Noise IC. The SPI bus serves as a general purpose, bi-directional, serial link between the BRC and other Base Radio modules, including the Exciter.  The SPI carries control and operational data signals to and from Exciter circuits.Synthesizer CircuitryThe synthesizer circuit consists of the Phase-Locked Loop (PLL) IC and associated circuitry.  This circuit’s controls the 1025 MHz VCO signal. An internal phase detector generates a logic pulse. This pulse is proportional to the phase or frequency difference between the reference frequency and loop pulse signal. The charge pump circuit generates a correction signal. The correction signal moves up or down in response to phase detector output pulses.  The correction signal passes through the low-pass loop filter. The signal then enters the 1025 MHz Voltage Controlled Oscillator (VCO) circuit.  1025 MHz Voltage Controlled Oscillator (VCO)For proper operation, the VCO requires a very low-noise, DC supply voltage.  An ultra low-pass filter prepares the necessary low-noise voltage and drives the oscillator. A portion of the oscillator output signal enters the synthesizer circuitry.  The circuitry uses this feedback signal to generate correction pulses. The 1025MHz VCO output mixes with the 90.3 MHz VCO output. The result is a Local Oscillator [LO) signal for the Low Noise IC. The LNODCT uses this LO signal to up-convert the programmed transmit frequency.  The Low Noise IC also uses the LO signal to down-convert the PA feedback signal.
14 68P80801H45-1   1/20/2002Base Radio Exciter EBTS System Manual - Vol 2QUAD Channel 900 MHz Exciter 90.3 MHz Voltage Controlled Oscillator (VCO)The synthesizer within the Low Noise IC sets the 90.3 MHz signal. The 90.3 MHz VCO provides a LO signal to the LNODCT IC. The Low Noise IC uses this signal in up-converting and down-converting the feedback signal. Regulator CircuitryThe voltage regulators generate three regulated voltages: +3 Vdc, +5 Vdc and +11.7 Vdc. The regulators obtain input voltages from the +3.3 Vdc and +14.2 Vdc backplane voltages.  The regulated voltages power various ICs and RF devices in the Exciter.Linear RF Amplifier StagesThe linear RF amplifiers boost the RF signal from the Low Noise IC. The RF Amplifier generates an appropriate signal level to drive the PA.
 22 68P80801H45-1   1/20/2002 800/900/1500 MHz Base Radios EBTS System Manual - Vol 2 ExciterDIFFERENTIALDATA & CLOCKFROMBRC MODULEADDRESS BUSFROM CONTROLMODULESPI BUSTO/FROM CONTROLMODULEADDRESS DECODE, MEMORY, & A/DCONVERTER CIRCUITRYEXCITER IC CIRCUITRY 970 MHZVCO CIRCUITRYSYNTHESIZERCIRCUITRYLINEAR RF AMPLIFIERCIRCUITRYLOINJECTIONCIRCUITRYMEMORYA/DCONVERTERVARIOUSSIGNALSTO MONITORDCFILTER+10 VCONTROL VOLTAGEOSCILLATORCHARGEPUMP2.4 MHZVCO FEEDBACKCHIPSELECTSPI BUS (CLOCK & DATA)FROM BACKPLANEPHASELOCKEDLOOPICRINFIN90.3VCOCIRCUITRYOSCILLATORBUFFERAMPLNODCT IC CIRCUITRYLNODCT ICTX DATA & CLOCKLOW-PASSLOOPFILTERBUFFERVCOFEEDBACKRF OUTPUTTO PA MODULEDACIQRF FEEDBACKFROM PA MODULEBUFFERAMPBPFREGULATORCIRCUITRY+11.7 VREGULATOR+14.2 VFROMBACKPLANE+3 VSOURCE+11.7 VSOURCE+5 VSOURCE+5 VREGULATOR+3 VREGULATOR(U3702)EBTS283Q080601JNMNOTE: Where two frequencies are given, frequency without parentheses applies to 800 MHz BR only and frequency with parentheses applies to 900 MHz BR only.+3.3 VFigure 9 800 and 900 MHz MHz QUAD Channel Exciter Functional Block Diagram
68P80801H45-1   1/20/2002 1EBTS System Manual - Vol 2 Power Amplifier (PA) Power Amplifier (PA)OverviewThis section provides technical information for the Power Amplifier (PA).  FRU Number to Kit Number Cross ReferencePower Amplifier (PA) Field Replaceable Units (FRUs) are available for the iDEN EBTS. The FRU contains the PA kit and required packaging. Table 1 provides a cross reference between PA FRU numbers and kit numbers.Section Page DescriptionPower Amplifer Overview 1 Describes the the various Base Radio Power Amplifier (PAs) for the single channel and QUAD Channel Base Radios (BR)s.PA Theory of Operation 8 Describes the various modules and functions for the various single channel and QUAD Channel Base Radios (BRs)40W - 800 MHz PA Functional Block Diagram (Sheet 1 of 1)17 Functional Block Diagram for the 40 Watt, 800 MHz, Single Channel Base Radio Power Amplifier (PA)70W - 800 MHz PA Functional Block Diagram (Sheet 1 of 1)18 Functional Block Diagram for the 70 Watt, 800 MHz, Single Channel Base Radio Power Amplifier (PA)60W - 900 MHz PA Functional Block Diagram (Sheet 1 of 1)19 Functional Block Diagram for the 60 Watt, 900 MHz, Single Channel Base Radio Power Amplifier (PA)40W - 1500 MHz PA Functional Block Diagram (Sheet 1 of 1)20 Functional Block Diagram for the 40 Watt, 1500 MHz, Single Channel Base Radio Power Amplifier (PA)800 MHz QUAD Channel BR PA Functional Block Diagram (Sheet 1 of 1)21 Functional Block Diagram for the 800 MHz QUAD Channel Base Radio Power Amplifier (PA)900 MHz QUAD Channel BR PA Functional Block Diagram (Sheet 1 of 1)21 Functional Block Diagram for the 900 MHz QUAD Channel Base Radio Power Amplifier (PA)Table 1    FRU Number to Kit Number Cross ReferenceDescription FRU Number Kit Number40 W- 800 MHz Single Channel Base Radio PA TLF2020 CLF177270 W- 800 MHz Single Channel Base Radio PA TLN3335 CLF177160 W- 900 MHz Single Channel Base Radio PA CLN1355 CLF130040 W- 1500 MHz Single Channel Base Radio PA TLN3426 TTG100052 W- 900 MHz QUAD Channel Base Radio PA DLN1202 CTF108252 W- 800 MHz QUAD Channel Base Radio PA CLF1499 CLF1400
268P80801H45-1   1/20/2002Power Amplifier (PA) EBTS System Manual - Vol 2Power Amplifer Overview Power Amplifer Overview    NOTEThe power outputs discussed on this section for the 800 MHz QUAD and 900 MHz QUAD Power Amplifiers are referenced to the single carrier mode, operating at 52 W average power output from the Power Amplifier’s output connector.The Power Amplifier (PA), with the Exciter, provides the transmitter functions for the Base Radio.  The PA accepts the low-level modulated RF signal from the Exciter. The PA then amplifies the signal for transmission and distributes the signal through the RF output connector. The 800 MHz Base Radio can be equipped with either 40 Watt PA, TLF2020 (version CLF1771) or 70 Watt PA, TLN3335 (version CLF1772). The 40W PA module consists of five hybrid modules, four pc boards, and a module heatsink/housing assembly.  The 70W PA module consists of eight hybrid modules, four pc boards, and a module heatsink/housing assembly. The 900 MHz Base Radio is equipped with 60 Watt PA, CLN1355 (kit no.  CLF1300A). The PA module consists of four hybrid modules, two pc boards, and a module heatsink/housing assembly.  The 1500 MHz Base Radio is equipped with 40 Watt PA, TLN3426 (version TTG1000). The PA module consists of four hybrid modules, two pc boards, and the module heatsink/housing assembly. The PA connects to the chassis backplane through a 96-pin DIN connector and three blindmate RF connectors.  Two Torx screws located on the front of the PA hold it in the chassis.Specifications of the transmitter circuitry, including the Exciter and PAs, are provided in Base Radio Overview section. Figure 1 shows the 40W, 800 MHz PA. Figure 2 shows the 70W, 800 MHz PA. Figure 3 shows the 60W, 900 MHz PA. Figure 4 shows the 40W, 1500 MHz PA. Figure 5 shows the 800 MHz QUAD PA (the 900 MHz QUAD PA is similar in appearance)
68P80801H45-1   1/20/2002 7EBTS System Manual - Vol 2 Power Amplifier (PA)Power Amplifer Overview Figure 5 800/900 MHz QUAD PA
868P80801H45-1   1/20/2002Power Amplifier (PA) EBTS System Manual - Vol 2PA Theory of Operation PA Theory of Operation  Table 2 describes the basic functions of the PA circuitry. Figures 6 and 7 show the functional block diagrams of 40W, 800 MHz and 70W, 800 MHz PA, respectively. Figure 8 shows the functional block diagram of the 60W, 900 MHz PA. Figure 9 shows a functional block diagram of the 40W, 1500 MHz PA. Figure 10 shows a functional block diagram of 800 MHz. Figure 10 shows a functional block diagram of 900 MHz QUAD PA.Table 2    Power Amplifier Circuitry   Circuit DescriptionDC/Metering Board • Serves as the main interface between the PA and the backplane board• Accepts RF input from the Exciter via a blindmate RF connector• Routes the RF input via a 50 Ω stripline to the Linear Driver Module RF amplifier• Routes the RF feedback from the RF Combiner/Peripheral Module to the Exciter via a blindmate RF connector• Provides digital alarm and metering information of the PA to the BRC via the SPI bus • Routes DC power to the fans and PA• Contains the thermistor that senses the PA temperature (800 MHz QUAD and 900 MHz QUAD)• Contains a Linear Driver Module and Linear Final Module Bias Enable Circuit (900 MHz QUAD)• Contains a Voltage Variable Attenuator Circuit (900 MHz QUAD)Linear Driver Module (LDM)• Contains two Class AB stages with the final stage in a parallel configuration (70W-800 MHz, 40W-800 MHz, 800 MHz QUAD)• Contains three cascaded Class AB stages with the first two stages configured as distributed amplifiers and the final stage in parallel configuration (900 MHz QUAD)• Contains three cascaded stages (Class A + Class AB + Class AB) with the final stage in push-pull configuration (900 MHz)• Contains four cascaded stages (Class A + Class AB + Class AB + Class AB) with the final stage in a push-pull configuration (1500 MHz)• Amplifies the low-level RF signal ~25 mW average power from the Exciter via the DC/Metering Board (900 MHz)• Amplifies the low level RF signal ~11mW average power from the Exciter via the DC/Metering Board (70W-800 MHz, 800 MHz QUAD*, 900 MHz QUAD*)• Amplifies the low-level RF signal ~8 mW average power from the Exciter via the DC/Metering Board  (40W- 800 MHz, 1500MHz)• Provides an output of:~8 W (70W, 800MHz) average power ~4 W (40W, 800 MHz) average power~6 W (800 MHz QUAD* and 900 MHz QUAD*) average power~17 W (900MHz) average power~16 W (1500MHz) average power
68P80801H45-1   1/20/2002 9EBTS System Manual - Vol 2 Power Amplifier (PA)PA Theory of Operation Interconnect Board(70W-800 MHz, 40W-800 MHz, 800 QUAD, and 900 MHz QUAD• Provides RF interconnection from the LDM to the RF Splitter board• Provides DC supply filteringRF Splitter/DC board • Interfaces with the DC/Metering Board to route DC power to the LFMs• Interfaces with the DC/Metering Board to route PA Bias Enable to the six Linear Final Modules (900 MHz Quad)• Contains splitter circuits that split the RF output signal of the LDM to the three Linear Final Modules (40W- 800 MHz)• Contains splitter circuits that split the RF output signal of the LDM to the six Linear Final Modules (70W- 800 MHz, 800 MHz QUAD and 900 MHz QUAD)• Contains a Quadrature splitter circuit to split the RF output signal of the LDM to the two Linear Final Modules (900 MHz and 1500 MHz)Linear Final Module (LFM)• Each module contains two Class AB amplifiers in parallel. Each module amplifies one of three RF signals (~ 84 W average power) from the LDM (via the Splitter/DC board). Three LFMs provide a sum RF output of approximately 48 W average power, before losses. (40W,  800MHz)• Each module contains two Class AB amplifiers in parallel. Each module amplifies one of six RF signals (~ 8 W average power) from the LDM (via the Splitter/DC board). Six LFMs provide a sum RF output of approximately 97 W average power, before losses. (70W, 800MHz)• Each module contains two Class AB amplifiers in parallel. Each module amplifies one of six RF signals (~6W average power) from the LDM (via the splitter/DC Board). Six LFMs provide a sum RF output of approximately 73W average power , before losses. (800 MHZ QUAD* and 900 MHz QUAD*)• Each module contains two Class push-pull AB amplifiers in parallel. Each module amplifies one of two RF signals (~ 17 W average power) from the LDM (via the Splitter/DC board). Two LFMs provide a sum RF output of approximately 75 W average power, before losses. (900MHz)• Each module contains two push-pull Class AB amplifiers in parallel. Each module amplifies one of two RF signals (~ 16 W average power) from the LDM (via the Splitter/DC board). Two LFMs provide a sum RF output of approximately 56W average power, before losses. (1500MHz)RF Interconnect Board(40W- 800 MHz PA only)• Contains three transmission lines that interconnect the LFMs to the RF Combiner/Peripheral ModuleCombiner Board(70W-800 MHz PA, 800 MHz QUAD, 900 MHz QUAD)• Contains three separate Quadrature combiner circuits that respectively combine the six RF outputs from the LFMs into three signals. These three signals, in turn, are applied to the RF Combiner/Peripheral Module. Table 2    Power Amplifier Circuitry  (Continued) Circuit Description
10 68P80801H45-1   1/20/2002Power Amplifier (PA) EBTS System Manual - Vol 2PA Theory of Operation DC/Metering Board (Non-QUAD PA)The DC/Metering Board provides the interface between the PA and the Base Radio backplane.  The preamplified/modulated RF signal is input directly from the Exciter via the Base Radio backplane. The RF input signal is applied to the input of the Linear Driver Module (LDM). The RF feedback signal is fed back to the Exciter, where it is monitored for errors. The primary function of the DC/Metering Boards is to monitor proper operation of the PA.  This information is forwarded to the Base Radio Controller (BRC) via the SPI bus.  The alarms diagnostic points monitored by the BRC on the PA include the following:❐Forward power❐Reflected power❐PA temperature sense❐Fan SensorRF Combiner/Peripheral Module • Contains a combiner circuit that combines the three RF signals from the RF Interconnect Board (40W- 800 MHz PA) or the Combiner Board (70W-800 MHz PA). It then routes the combined RF signal through a single stage circulator and a Low Pass Filter. The final output signal is routed to the blindmate RF connector (40W-800 MHz and 70W-800 MHz PAs).• Contains a combiner circuit that combines the three RF signals from the Combiner Board. It then routes the combined RF signal through a dual stage circulator and a Low Pass Filter. The final output signal is routed to the blindmate RF output connector. (800 MHz QUAD and 900 MHz QUAD PAs)• Contains a Quadrature combiner circuit to combine the RF signal from the two LFMs. It routes the combined RF signal through a circulator and a Low Pass Filter. The output signal is routed to the blindmate RF connector (900 MHz and 1500 MHz PAs)• Contains an RF coupler that provides an RF feedback signal to the Exciter via a blindmate RF connector on the DC/Metering Board. Also contains a forward and reverse power detector for alarm and power monitoring purposes.• Contains the thermistor that senses PA temperature and feeds the signal back to the DC/Metering Board for processing (40W-800 MHz, 70W-800 MHz, 900 MHz and 1500 MHz)Fan Assembly • Consists of three fans used to keep the PA within predetermined operating temperaturesNOTE:  *  The power outputs described in this section for the 800 QUAD and 900 QUAD PAs are references to the single carrier mode operating at 52W average power out from the PA output connector.Table 2    Power Amplifier Circuitry  (Continued) Circuit Description
68P80801H45-1   1/20/2002 11EBTS System Manual - Vol 2 Power Amplifier (PA)PA Theory of Operation DC/Metering Board (QUAD PA Only)The DC/Metering Board in the QUAD Radio serves the same function as it does in other radios. However, its circuitry is modified for compatibility with the QUAD Station. As a result, its logic circuitry is operated at 3.3 VDC.In addition to the functions listed for non-QUAD versions above, the following meter points are ported to the SPI bus:❐A and B Currents❐Thermistor (for PA temperature sensing circuit on the DC/Metering Board)❐Voltage Variable Attenuator Circuit (900 MHz QUAD version)❐PA Bias Enable Circuitry (900 MHz QUAD version)Linear Driver Module40W-800 MHz, 70W-800 MHZ and 800 MHZ QUAD PAsThe Linear Driver Module (LDM) amplifies the low-level RF signal from the Exciter.  The LDM consists of a two-stage cascaded Class AB amplifier, with the final stage in a parallel configuration. See Table 2 for the approximate input and output levels of the various LDMs. The LDM output is fed to the RF Splitter/DC Distribution Board via an Interconnect Board.900 MHz PAThe Linear Driver Module (LDM) amplifies the low-level RF signal from the Exciter.  The LDM consists of a three-stage, cascaded, Class AB amplifier, with the first two stages configured as distributed amplifiers and the final stage in a push-pull configuration.  This output is fed directly to the RF Splitter/DC Distribution Board.See Table 2 for the approximate input and output power of the 900 MHz LDM.The LDM output is fed to the RF Splitter/DC Distribution Board via the Interconnect Board.1500 MHz PAThe Linear Driver Module (LDM) takes the low level RF signal and amplifies it. The LDM consists of a four stage, cascaded, Class AB amplifier, with the final stage configured in push-pull configuration. This output is fed directly to the RF Splitter/DC Distribution Board.See Table 2 for the approximate input and output power of the 1500 MHz LDM.
12 68P80801H45-1   1/20/2002Power Amplifier (PA) EBTS System Manual - Vol 2PA Theory of Operation 900 QUAD PAThe Linear Driver Module (LDM) amplifies the low-level RF signal from the Exciter. The LDM consists of a three stage, cascaded, Class AB amplifier, with the final stage in a parallel configuration. See Table 2 for the approximate input and output power of the 900 MHz QUAD LDM. The LDM Output is fed to the RF Splitter/DC Distribution Board via the Interconnect Board.Interconnect Board (40W-800 MHz, 70W-800 MHz , 800 MHz QUAD and 900 MHz QUAD)The output of the LDM is applied to the Interconnect Board, which provides an RF connection to the RF Splitter/DC Distribution Board.  As a separate function, area on the Interconnect Board serves as a convenient mounting location for electrolytic capacitors used for filtering the +28 VDC supply. RF Splitter/DC Distribution Board40W-800 MHz, 70W-800 MHz, 800 MHz QUAD and 900 MHz QUADThe RF Splitter portion of this board accepts the amplified signal from the LDM (via the Interconnect Board).  The primary function of this circuit is to split the RF signal into drive signals for the LFMs. In the 40W-800 MHz PA, this circuit splits the drive signal into three separate paths to be applied to the three LFMs, where the signals will be amplified further.  In the 70W-800 MHz, 800 MHz QUAD and 900 MHZ QUAD PAs, this circuit splits the drive signal into six separate paths to be applied to the six LFMs, where the signals will be amplified further.The DC Distribution portion of this board interfaces directly with the DC/Metering Board to route DC power to the LFMs and provide PA Bias Enable (900 MHz QUAD only)900 MHz and 1500 MHzThe RF Splitter portion of this board accepts the amplified signal from the LDM.  The primary function of this circuit is to split the RF signal into two separate paths.  These two outputs are fed directly to two separate Linear Final modules where the RF signals will be amplified further. The DC Distribution portion of this board interfaces directly with the DC/Metering Board to route DC power to the LFMs.
68P80801H45-1   1/20/2002 13EBTS System Manual - Vol 2 Power Amplifier (PA)PA Theory of Operation Linear Final Modules 40W-800 MHz, 70W-800 MHz, 800 MHz QUAD and 900 MHz QUADThe RF Splitter output signals are applied directly into the LFMs for final amplification.  Each LFM contains a coupler that splits the LFM input signal and feeds the parallel Class AB amplifiers that amplify the RF signals. In the 40W PA, the amplified signals are then combined on the LFM and sent directly to the RF Interconnect Board. In the 70W PA, the amplified signals are then combined on the LFM and sent directly to the Combiner Board.See Table 2 for the approximate total summed output powers of the various LFMs, before output losses.900 MHz PAThe RF signals from the outputs of the RF Splitter are applied directly into the Linear Final Module (LFM) for final amplification.  Each LFM contains a branchline coupler that splits the LFM’s input signal and feeds the dual Class AB push-pull amplifiers that amplify the RF signals. The amplified signals are then combined on the LFM and sent directly to the RF Combiner circuit for final distribution. See Table 2 for the approximate total summed output power of the 900 MHz LFMs, before output losses.1500 MHz PAThe two RF signals from the outputs of the RF Splitter are input directly into the Linear Final Module (LFM) for final amplification. Each LFM contains a branchline coupler that splits the LFM’s input signal and feeds the dual Class AB push-pull amplifiers that amplify the RF signals. The amplified signals are then combined on the LFM , via a branchline coupler, and sent directly to the RF Combiner circuit for final distribution. See Table 2 for the approximate total summed output power of the 1500 MHz LFMs, before output losses.The current drains of the 1500 MHz LFMs are monitored by the A/D converter on the DC/Metering board. A voltage signal representative of the LFM current drain is sent to the BRC. A Power Amplifier alarm is generated if the signal is outside of either the upper or lower limits.RF Interconnect Board (40W- 800 MHz PA Only)The RF Interconnect Board consists of transmission line paths which route the three output signals from the LFMs to the three inputs of the RF Combiner/Peripheral Module.Combiner Board (40W- 800 MHz, 70W- 800 MHz, 800 MHz QUAD and 900 MHz QUAD PAs)The Combiner Board combines pairs of signals into single signals, thereby combining the six signals from the LDMs into three signals.  The resulting three signals are applied to the RF Combiner/Peripheral Module.
14 68P80801H45-1   1/20/2002Power Amplifier (PA) EBTS System Manual - Vol 2PA Theory of Operation RF Combiner/Peripheral Module (40- 800 MHz, 70W- 800 MHz PAs)This module consists of two portions: an RF combiner and a peripheral module.  The RF Combiner portion of the module combines the three RF signals from the RF Interconnect Board (40W- 800 MHz PA) or the Combiner Board (70W- 800 MHz PA) into a single signal using a Wilkinson coupler arrangement. Following the combiner circuit, the single combined RF signal is then passed through a directional coupler which derives a signal sample of the LFM RF power output.  Via the coupler, a sample of the RF output signal is fed to the Exciter, via the DC/Metering Board, as a feedback signal.  Following the coupler, the power output signal is passed through a single stage circulator, which protects the PA in the event of high reflected power. The peripheral portion of the module provides a power monitor circuit that monitors the forward and reflected power of the output signal.  This circuit furnishes the A/D converter on the DC/Metering Board with input signals representative of the forward and reflected power levels.  For forward power, a signal representative of the measured value is sent to the BRC via the SPI bus.  The BRC determines if this level is within tolerance of the programmed forward power level.  If the level is not within parameters, the BRC will issue a warning to the site controller which, in turn, will shut down the Exciter if required.Reflected power is monitored in the same manner.  The BRC uses the reflected power to calculate the voltage standing wave ratio (VSWR).  If the VSWR is determined to be excessive, the forward power is rolled back.  If it is extremely excessive, the BRC issues a shut-down command to the Exciter.A thermistor is located on the RF Combiner/Peripheral module to monitor the operating temperature of the PA.  The thermistor signal indicating excessive temperature is applied to the A/D converter and then sent to the BRC.  The BRC rolls back forward power if the monitored temperature is excessive.900 MHz PAThis module consists of two parts: an RF combiner and a peripheral module. The RF combiner combines the two RF signals from each LDM into a single signal, using a branchline coupler arrangement. Then, the RF signal passes through a directional coupler which derives a signal sample of the LFMs RF power output.  Via the coupler, a sample of the RF output signal is fed to the Exciter, via the DC/Metering Board, as a feedback signal, thereby allowing the Exciter to accordingly adjust signal drive. Following the coupler, the power output signal is passed through a circulator, which protects the PA in the event of high reflected power.  A power monitor circuit monitors the forward and reflected power of the output signal.  This circuit furnishes the A/D converter on the DC/Metering Board with input signals representative of the forward and reflected power levels. For forward power, a signal representative of the measured value is sent to the BRC via the SPI bus.  The BRC determines if this level is within tolerance of the programmed forward power level.  If the level is not within parameters, the BRC will issue a warning to the site controller which, in turn, will shut down the Exciter if required.
68P80801H45-1   1/20/2002 15EBTS System Manual - Vol 2 Power Amplifier (PA)PA Theory of Operation Reflected power is monitored in the same manner.  The BRC uses the reflected power to calculate the voltage standing wave ratio (VSWR).  If the VSWR is determined to be excessive, the forward power is rolled back.  If it is extremely excessive, the BRC issues a shut-down command to the Exciter.A thermistor is located on the RF Combiner/Peripheral module to monitor the operating temperature of the PA.  A voltage representative of the monitored temperature is sent from the A/D converter to the BRC.  The BRC rolls back forward power if the monitored temperature is excessive.1500 MHzBoth LFM outputs are input into this module where they are combined, with a branchline coupler, for a single output signal. The RF signal is first coupled to the Exciter module, via the DC/Metering Board, so that it can be monitored. The RF output signal is then passed through a circulator that acts as a protection device for the PA in the event of reflected power. A power monitor circuit monitors the forward and reflected power of the output signal. This circuit provides the A/D converter on the DC/Metering board with an input signal representative of the forward or reflected power levels. For forward power, a signal representative of the measured value is sent to the BRC module via the SPI bus. The BRC determines if this level is within tolerance of the programmed forward power level. The programmed forward power is set through the use of MMI commands. If the level is not within certain parameters, the BRC will issue a warning to the site controller and may shut-down the Exciter module.Reflected power is monitored in the same manner except that the BRC determines an acceptable reflected power level. The BRC calculates the reflected power through an algorithm stored in memory. If the reflected power is determined to be excessive, the forward power is rolled back. If the reflected power level is extremely excessive, the BRC will issues a shut-down command to the Exciter module.A thermistor is located on the RF Combiner/Peripheral module to monitor the operating temperature of the Power Amplifier. A voltage representative of the monitored temperature is sent from the A/D converter to the BRC. The BRC issues a cut-back command to the Exciter module if the monitored temperature is greater than 121˚ F (85˚ C).RF Combiner/Peripheral Module (800 MHz QUAD and 900 MHz QUAD)This module consists of two parts: an RF combiner and a Peripheral module. The RF combiner combines three RF signals from the Combiner Board into a single signal using a Wilkinson coupler arrangement. Following the combiner circuit, the single combined RF signal is then passed through a directional coupler, which derives a signal sample of the LFM RF power output. Via the coupler, a sample of the RF output signal is fed to the Exciter, via the DC/Metering Board, as a feedback signal. Following the coupler, the power output signal is passed through a dual stage circulator, which protects the PA in the event of high reflected power.
16 68P80801H45-1   1/20/2002Power Amplifier (PA) EBTS System Manual - Vol 2PA Theory of Operation The Peripheral module provides a power monitor circuit that monitors the forward and reflected power of the output signal. This circuit furnishes the A/D converter on the DC/Metering Board with input signals, representative of the forward and reflected power levels. For forward power, a signal representative of the measured value is sent to the BRC via the SPI bus. The BRC determines if this level is within tolerance of the programmed forward power level. If the level is not within tolerance, the BRC will issue a warning to the site controller, which, in turn, will shut down the Exciter, if required.Reflected power is monitored in the same manner. The BRC uses the reflected power to calculate the voltage standing wave ratio (VSWR). If the VSWR is calculated as excessive, forward power is rolled back. If the VSWR calculation is exceedingly out of tolerance, the BRC issues a shut-down command to the Exciter.NOTEThe Thermistor that monitors the operating temperature of the 800 MHZ QUAD and 900 MHz QUAD PAs is located on the DC/Metering BoardFan ModuleThe PA contains a fan assembly to maintain normal operating temperature through the use of a cool air intake.  The fan assembly consists of three individual fans in which airflow is directed across the PA heatsink.  The current draw of the fans is monitored by the DC/Metering Board.  A voltage representative of the current draw is monitored by the BRC.  The BRC flags the iSC if an alarm is triggered.  The PA LED on the front panel of the BRC also lights, however the PA does not shut down due to a fan failure alone.
 22 68P80801H45-1   1/20/2002 800/900/1500 MHz Base Radios EBTS System Manual - Vol 2 Power AmplifierCOMBINERBOARDLINEAR DRIVER MODULELINEAR FINALMODULES50 OHMLOADADDRESS BUSFROM BRCSPI BUSTO/FROM BRCADDRESS DECODE, MEMORY,& A/D CONVERTER CIRCUITRYMEMORYA/DCONVERTERBOARD SELECTDECODECIRCUITRYPA TEMP SENSECHIPSELECTCHIP SELECTDECODECIRCUITRYCHIP SELECTRF COMBINER/PERIPHERAL MODULELOW-PASSFILTERRF INPUTRF OUTTO ANTENNARF FEEDBACKTO EXCITERMODULEREF PWRFWD PWRFAN SENSEFAN ASSEMBLYTEMPERATURESENSOREBTS417_900121701JNMCLK/DATACIRCULATOR50 OHMLOAD50 OHMLOAD50 OHMLOAD50 OHMLOAD50 OHMLOAD50 OHMLOADSTAGE 2CLASS ABRF SPLITTER/DCDISTRIBUTION BOARDINTERCONNECTBOARDSTAGE 3CLASS ABDCFILTER+28 VDCCIRCULATOR50 OHMLOAD50 OHMLOAD50 OHMLOAD50 OHMLOAD50 OHMLOADEEPOTSTAGE 2CLASS ABDISTRIBUTEDSTAGE 1CLASS ABDISTRIBUTEDC_EINCV_DVVAPA_ENABLE (PA_E)PA_E PA_EPA_EPA_EPA_EPA_EPA_EPA_EPA_EPA_EPA_EPA_EPA_EPA_EFigure 11 900 MHz QUAD Channel BR PA Functional Block Diagram(Sheet 1 of 1)900 MHz QUAD Power Amplifier – DLN1202 (CTF1082)Functional Block Diagram
68P80801H45-1   1/20/2002 1EBTS System Manual - Vol 2 DC Power Supply DC Power SupplyOverviewThis section provides technical information for the DC Power Supply (PS). FRU Number to Kit Number Cross ReferenceDC Power Supply Field Replaceable Units (FRUs) are available for the iDEN EBTS. The FRU contains the Power Supply kit and required packaging. Table 1 provides a cross reference between Exciter FRU numbers and kit numbers. Chapter Page DescriptionSingle Channel DC Power Supply Overview1 Describes the functions and characteristics of the DC Power Supply (PS) module for the single channel Base Radio (BR).DC Power Supply for QUAD Channel Base Radios5 Describes the functions and characteristics of the DC Power Supply (PS) module for the QUAD channel Base Radio (BR).DC Power Supply Functional Block Diagram (Sheet 1 of 2)9 Functional Block Diagram for the Single Channel DC Power Supply (PS)QUAD BR DC Power Supply (Sheet 1 of 2)11 Functional Block Diagram for the QUAD Channel DC Power Supply (PS)Table 1    FRU Number to Kit Number Cross ReferenceDescription FRU Number Kit NumberSingle Channel DC Power Supply  TLN3338 CPN1027QUAD Channel DC Power Supply CLN1498 CLN1461
68P80801H45-1   1/20/2002 5EBTS System Manual - Vol 2 DC Power SupplyDC Power Supply for QUAD Channel Base Radios DC Power Supply for QUAD Channel Base RadiosQUAD Channel DC Power Supply OverviewThe QUAD Channel DC Power Supply provides DC operating voltages to QUAD Channel Base Radio FRUs. The power supply accepts input voltage sources from 41VDC to 60VDC. Input sources may be either positively or negatively grounded.On initial startup, the supply requires a nominal 43 VDC. If the voltage drops below 41 VDC, the QUAD Channel DC Power Supply enters quiescent mode. In quiescent mode, the power supply emits no power.The QUAD Channel DC Power Supply is designed for sites with an available DC voltage source. Output voltages from the DC Power Supply are 28.6 VDC, 14.2 VDC and 3.3 VDC, with reference to output ground. The supply is rated for 575 Watts of continuous output, with up to 113˚ F (45˚ C) inlet air. At 140˚ F (60˚ C), the 28.6 VDC output reduces to 80% of maximum. The QUAD Channel DC Power Supply consists of the Power Supply and front panel hardware. The QUAD Channel DC Power Supply connects to the chassis backplane through an edgecard connector. Two Torx screws on the front panel secure the QUAD Channel DC power supply to the chassis.Figure 2 shows the QUAD Channel Power Supply with the cover removed.Figure 2 Quad Carrier Power Supply
668P80801H45-1   1/20/2002DC Power Supply EBTS System Manual - Vol 2DC Power Supply for QUAD Channel Base Radios QUAD Channel DC Power Supply Controls and IndicatorsTable 5 summarizes LED indications on the QUAD Channel DC Power Supply during normal operation. The ON/OFF switch behind the front panel turns DC power supply on and off.QUAD Channel DC Power Supply Performance Specifications Table 6 lists the specifications for the QUAD Channel DC Power Supply.Table 5    DC Power Supply IndicatorsLED Condition IndicationsGreen Solid (on) Power Supply is on, and operating under normal conditions with no alarmsOff Power Supply is turned off or required power is not availableRed Solid (on) Power Supply fault or load fault on any output, or input voltage is out of rangeOff Power Supply is operating normally, with no alarmsTable 6    DC Power Supply Specifications  Description Value or RangeOperating Temperature 0° to +40° C (no derating)+41° to +60° C (derating)Input Voltage 41 to 60 VDCInput Polarity Positive (+) ground systemStartup Voltage 43 VDC (minimum)Input Current 18.0 A (maximum) @ 41 VDCSteady State Output Voltages 28.6 VDC +5%14.2 VDC +5%3.3 VDC +5%Total Output Power Rating 575 W (no derating)485 W (derating)Output Ripple All outputs 150mV p-p (measured with 20 MHz BW oscilloscope at 25°C)High Frequency individual harmonic voltage limits (10kHz to 100MHz) are:28.6 VDC 1.5 mV p-p14.2 VDC  3.0 mV p-p3.3 VDC 5.0 mV p-pShort Circuit Current 0.5 A average (maximum)
68P80801H45-1   1/20/2002 7EBTS System Manual - Vol 2 DC Power SupplyDC Power Supply for QUAD Channel Base Radios QUAD Channel DC Power Supply Theory of OperationTable 7 briefly describes the basic DC Power Supply circuitry. Figure 5 shows the functional block diagrams for the DC Power Supply.Table 7    DC Power Supply Circuitry Circuit DescriptionInput Circuit Routes input current from the DC power input cable through the high current printed circuit edge connector, EMI filter, panel mounted combination circuit breaker, and on/off switchStartup Inverter CircuitryProvides VDC for power supply circuitry during initial power-upMain Inverter Circuitry Consists of a switching-type power supply to generate the +28.6 VDC supply voltageTemperature Protection The Power Supply contains a built-in cooling fan that runs whenever the supply is powered on. The supply shuts down if the temperature exceeds a preset threshold+14.2 VDC Secondary Converter CircuitryConsists of a switching-type power supply to generate the +14.2 VDC supply voltage+3.3 VDC Secondary Converter CircuitryConsists of a switching-type power supply to generate the +3.3 VDC supply voltageClock Generator CircuitryGenerates the 267 kHz and 133 kHz clock signals used by the pulse width modulators in the four inverter circuitsAddress Decode, Memory, & A/D ConverterServes as the main interface between A/D on the Power Supply and the BRC via the SPI bus
    1/20/2002 11 EBTS System Manual - Vol 2 800/900/1500 MHz Base Radios DC Power Supply  +5.1 V INVERTER CIRCUITRYFETDRIVERPOWER FETSWITCH FILTERCIRCUITRYVCCVCC+ 5V OVERCURRENTDETECTREFREFSURGE CURRENTDELAY REFOVERVOLTAGEDETECTFETCROWBARCIRCUIT+ 28V BULKPULSEWIDTHMODULATORA24253031+5.1 V DCTOSTATIONMODULESVIABACKPLANEP/OBACKPLANECONNECTOR+5.1 V÷ 2CLOCK GENERATOR CIRCUITRYSTARTUP INVERTER CIRCUITRYBULK DETECTTODIAGNOSTICSCIRCUITRYPULSEWIDTHMODULATORVCCVCC STARTUP ISOLATIONTRANSFORMER+14.2 V INVERTER CIRCUITRYFETDRIVERPOWER FETSWITCH FILTERCIRCUITRYVCCVCC+ 14.2V OVERCURRENTDETECTREFREFSURGE CURRENTDELAY REFOVERVOLTAGEDETECTFETCROWBARCIRCUITA16172223+14.2V DCTOSTATIONMODULESVIABACKPLANEP/OBACKPLANECONNECTOR+14.2V+14.2VPULSEWIDTHMODULATORPULSEWIDTHMODULATORFRONT PANELON / OFFSWITCHEXTERNALDC INPUT41-60 VDCFILTERCIRCUITRYINPUT FILTER BOARD341415+28.6 VDCTOSTATIONMODULESVIABACKPLANEP/OBACKPLANECONNECTORMAIN INVERTER CIRCUITRYREFREFCURRENTDETECT A+28.6 V  OVERVOLTAGEDETECT+28 V BULK TODIAGNOSTICSCIRCUITRYOVERCURRENTDETECT+28.6 VDCCLOCKGENERATORCIRCUITRY267 KHZTRANSISTORSWITCHBMAIN ISOLATIONTRANSFORMERTRANSISTORDRIVERSSOFTSTARTCIRCUITRYSHUTDOWNA+12V STARTUP BIAS+12V STARTUP BIASVCCVCCMOD FAIL133 KHZ267 KHZ133 KHZ133 KHZ133 KHZ133 KHZ133 KHZ267 KHZ133 KHZ267 KHZ133 KHZPOWER FETSWITCHES FILTERINGCIRCUITRY+28 V BULKEBTS323011497JNMFigure 5QUAD BR DC Power Supply (Sheet 1 of 2)
 12    1/20/2002 800/900/1500 MHz Base Radios EBTS System Manual - Vol 2 DC Power Supply  A/DCONVERTERCOOLINGFANTHERMISTORMOUNTED ONHEATSINKSPI BUSREFREFREFMOD FAILINPUT FAILHEATSINK DIAG+5.1 V+14.2V DIAG+5.1 V DIAG+28.6 V DIAGREFREFHEATSINK STATUSDETECTHI-TEMPDETECTBULK DETECTFROM STARTUPINVERTERCIRCUITRYFROMDETECTCIRCUITRYABINPUT GOOD(GREEN)MODULEFAIL(RED)3SPI BUSTO/FROMSTATION CONTROLMODULEADDRESS DECODE CIRCUITRYADDRESSDECODECIRCUITRYFROMSTATIONCONTROLBOARD9P/O ADDRESS BUS ENABLE ENABLEDIAGNOSTICS CIRCUITRYT°EBTS324012097JNMJ300REFFigure 6QUAD BR DC Power Supply Functional Block Diagram (Sheet 2 of 2)
44 68P80801H45-1   1/20/2002Troubleshooting EBTS System Manual - Vol 2QUAD Channel Base Radio/Base Radio FRU Replacement Procedures QUAD Channel Base Radio/Base Radio FRU Replacement ProceduresReplace suspected station modules with known non-defective modules to restore the station to proper operation. The following procedures provide FRU replacement instructions, post-replacement adjustments and verification instructions.QUAD Base Radio Replacement ProcedureNOTEBase Radio removal and installation procedures appear for reference or buildout purposes. Field maintenance of Base Radios typically consists of replacement of FRUs within the Base Radio. Perform Base Radio FRU replacement according to “Base Radio FRU Replacement Procedure” below.Perform Base Radio (BR) replacement as described in the following paragraphs.CAUTION!CAUTION!Improper lifting or dropping the BR could result in serious personal injury or equipment damage.Base Radios are HEAVY!Handle the BR with extreme caution, and according to local health and safety regulations.RemovalRemove the BR from the Equipment Cabinet as follows:CAUTION!CAUTION!A Single Carrier BR can weigh up to 76 LBS (34 KG). A Quad Carrier BR can weigh up to 91 LBS (41 KG). Handle the BR with extreme caution, and according to local health and safety regulations.
68P80801H45-1   1/20/2002 45EBTS System Manual - Vol 2 TroubleshootingQUAD Channel Base Radio/Base Radio FRU Replacement Procedures 1. Remove power from the Base Radio by setting the Power Supply ON/OFF switch to the OFF position.2. Tag and disconnect the cabling from the BR rear panel connectors.3. Remove the Power Amplifier module to reduce the BR weight. Remove the two M10 Torx screws that secure the Power Amplifier module. Slide the module out of the chassis.4. Remove the four M30 TORX screws which secure the BR front panel to the Equipment Cabinet mounting rails.5. While supporting the BR, carefully remove the BR from the Equipment Cabinet by sliding the BR from the front of cabinet. When the BR becomes free from its mounting rails, be sure to fully support it.InstallationInstall BR in Equipment Cabinet as follows:CAUTION!CAUTION!A Single Carrier BR can weigh up to 76 LBS (34 KG). A Quad Carrier BR can weigh up to 91 LBS (41 KG). Handle the BR with extreme caution, and according to local health and safety regulations.1. If adding a BR, install side rails in the appropriate BR mounting position in the rack.2. Remove the Power Amplifier module to reduce the BR weight. Remove the two M10 Torx screws that secure the Power Amplifier module. Slide the module out of the chassis.3. While supporting the BR, carefully lift and slide the BR in the Equipment Cabinet mounting position.4. Secure the BR to the Equipment Cabinet mounting rails using four M30 Torx screws. Tighten the screws to 40 in-lb (4.5 Nm).5. Slide the Power Amplifier module back into the BR chassis. Replace two M10 Torx screws that secure the Power Amplifier module. Secure the module by tightening the screws to the specified torque of 5 in-lbs.6. Connect the cabinet cabling to the BR. Refer to Backplane figure XX.7. Perform BR activation as described below.
46 68P80801H45-1   1/20/2002Troubleshooting EBTS System Manual - Vol 2QUAD Channel Base Radio/Base Radio FRU Replacement Procedures NOTEBase Radio removal and installation procedures appear for reference or buildout purposes. Field maintenance of Base Radios typically consists of replacement of FRUs within the Base Radio. Perform Base Radio FRU replacement according to “Base Radio FRU Replacement Procedure” below.Anti-Static PrecautionsCAUTIONThe Base Radio contains static-sensitive devices. Prevent electrostatic discharge damage to Base Radio modules! When replacing Base Radio FRUs, wear a grounded wrist strap. Observe proper anti-static procedures.Motorola publication 68P81106E84 provides complete static protection information. This publication is available through Motorola National Parts. Observe the following additional precautions:❐Wear a wrist strap (Motorola Part No. 4280385A59 or equivalent) at all times when servicing the Base Radio to minimize static build-up.❐A grounding clip is provided with each EBTS cabinet. If not available, use another appropriate grounding point.❐DO NOT insert or remove modules with power applied to the Base Radio. ALWAYS turn the power OFF using the Power Supply rocker switch on the front of the Power Supply module.❐Keep spare modules in factory packaging for transporting. When shipping modules, always pack in original packaging.
68P80801H45-1   1/20/2002 47EBTS System Manual - Vol 2 TroubleshootingQUAD Channel Base Radio/Base Radio FRU Replacement Procedures QUAD BRs Radio FRU Replacement ProcedurePerform the following steps to replace any of the Base Radio FRUs:NOTEAfter a Control Board or BR replacement, the integrated Site Controller (iSC) reboots the BR. Whenever the BR goes off-line, the Replacement BRC Accept Timer begins counting down. A BR reboot occurs if the BR remains off-line as the timer times out. (The timer’s default period is three minutes.) If someone turns on the BR before the timer times out, power down the BR. Then wait for the minimum timer period before turning on the BR.1. Notice the Power Supply rocker switch, behind the front panel of the Power Supply. Set the Power Supply rocker switch to the OFF (0) position. Turning off this switch removes power from the Base Radio.2. Loosen the front panel fasteners. These are located on each side of the module being replaced.3. Pull out the module.4. Insert the non-defective replacement module by aligning the module side rails with the appropriate rail guides inside the Base Radio chassis. 5. Gently push the replacement module completely into the Base Radio chassis assembly using the module handle(s). CAUTIONDO NOT slam or force the module into the chassis assembly. Rough handling can damage the connectors or backplane.6. Secure the replacement module by tightening the front panel fasteners to the specified torque of 5 in-lbs.7. Apply power to the Base Radio by setting the switch to the ON position.8. Perform the Station Verification Procedure.
48 68P80801H45-1   1/20/2002Troubleshooting EBTS System Manual - Vol 2QUAD Channel Base Radio/Base Radio FRU Replacement Procedures QUAD BR Power Amplifier (PA) Fan FRU ReplacementPerform the following steps to replace the Power Amplifier (PA) fans.1. Remove the Power Amplifier from the Base Radio per FRU Replacement Procedure.2. Disconnect fan power cable from PA housing.3. Remove front panel from fan assembly.4. Remove fan assembly from PA chassis. NOTETo install the new fan kit, reverse above procedure.
68P80801H45-1   1/20/2002 49EBTS System Manual - Vol 2 TroubleshootingQUAD Base Radio Station Verification Procedures QUAD Base Radio Station Verification ProceduresPerform the Station Verification Procedures whenever you replace a FRU. The procedures verify transmit and receive operations. Each procedure also contains the equipment setup.QUAD BR Replacement FRU VerificationBefore shipment, the factory programs all module-specific information. Base Radio specific information (e.g., receive and transmit frequencies) involves a download to the Base Radio from the network/site controller.The Base Radio does not require replacement FRU alignment. QUAD BR Base Repeater FRU Hardware Revision VerificationNOTEThe following procedure requires the Base Radio to be out of service. Unless the Base Radio is currently out of service, Motorola recommends performing this procedure during off-peak hours. Performing this procedure then minimizes or eliminates disruption of service to system users.1. Connect one end of the RS-232 cable to the service computer.2. Connect the other end of the RS-232 cable to the STATUS port, located on the front panel of the EX/CNTL module.3. Power on the BR using the front switch on the Power Supply Module. Press the reset button on the Control Module front panel. At the prompt, hit a Carriage Return on the service computer to enter the test application mode. Use the user_id -ufield and the password motorola, log in to the BR
50 68P80801H45-1   1/20/2002Troubleshooting EBTS System Manual - Vol 2QUAD Base Radio Station Verification Procedures NOTEFuture versions of the QUAD BR will ship with software that recognizes the BR cabinet position. Default Motorola Manufacturing BR programmed cabinet position is (0,0), which automatically sends the radio to Test Application software mode upon power up. Upon setting a valid cabinet position, the radio will default to the Call Processing mode of operation..4. Collect revision numbers from the station by typing the following command:5. If all modules return revision numbers of the format “Rxx.xx.xx”, then all revision numbers are present. In that case, verification requires no further action. If revision numbers return as blank, or not in the format “Rxx.xx.xx”, contact your local Motorola representative or Technical Support.6. Set desired cabinet id, position, and of BR by typing the following commands, with the final number on each command being the desired cabinet id and position. The command example below sets cabinet id to 5, and cabinet position to 2.7. After checking all BRs, log out by keying the following command:NOTETo start Call Processing mode of operation, reset the Base Radio using the front panel switch.> login -ufieldpassword: motorolafield>field> fv -oplatformfield>field> ci -oplatform -c5field> pi -oplatform -p2field>field> logout
68P80801H45-1   1/20/2002 51EBTS System Manual - Vol 2 TroubleshootingQUAD Base Radio Station Verification Procedures QUAD BR Transmitter VerificationThe transmitter verification procedure verifies the transmitter operation and the integrity of the transmit path. This verification procedure is recommended after replacing an Exciter, Power Amplifier, BRC, or Power Supply module.NOTEThe following procedure requires the Base Radio to be out of service. Unless the Base Radio is currently out of service, Motorola recommends performing this procedure during off-peak hours. This minimizes or eliminates disruption of service to system users.Equipment SetupTo set up the equipment, use the following procedure:1. Remove power from the Base Radio by setting the Power Supply rocker switch (located behind the front panel of the Power Supply) to the OFF (0) position.2. Connect one end of the RS-232 cable to the service computer.3. Connect the other end of the RS-232 cable to the STATUS port located on the front panel of the BRC. CAUTION!CAUTION!Make sure power to BR is OFF before disconnecting transmitter RF connectors. Disconnecting transmitter RF connectors while the BR is keyed may result in RF burns from arcing.4. Disconnect the existing cable from the connector labeled PA OUT. This connector is located on the backplane of the Base Radio.5. Connect a test cable to the PA OUT connector.6. Connect a 10 dB attenuator (100 W or more average power dissipation) on the other end of the test cable.7. From the attenuator, connect a cable to the RF IN/OUT connector on the R2660 Communications Analyzer.8. Remove power from the R2660 and connect the Rubidium Frequency Standard 10MHZ OUTPUT to a 10 dB attenuator.
52 68P80801H45-1   1/20/2002Troubleshooting EBTS System Manual - Vol 2QUAD Base Radio Station Verification Procedures 9. Connect the other end of the 10 dB attenuator to the 10MHZ REFERENCE OSCILLATOR IN/OUT connector on the R2660.NOTERefer to the equipment manual provided with the R2660 for further information regarding mode configuration of the unit (Motorola Part No. 68P80386B72). 10. Set the R2660 to the EXT REF mode.11. Apply power to the R2660.12. Set the R2660 to the SPECTRUM ANALYZER mode with the center frequency set to the transmit frequency of the Base Radio under test.13. Perform the appropriate transmitter verification procedure below for the particular Power Amplifier used in the Base Radio.
68P80801H45-1   1/20/2002 53EBTS System Manual - Vol 2 TroubleshootingQUAD Base Radio Station Verification Procedures Transmitter Verification Procedure(QUAD Carrier 800 MHz and 900 MHz Power Amplifiers)This procedure provides commands and responses to verify proper operation of the transmit path for 800 MHz and 900 MHz QUAD Channel Base Radios. 1. Power on the BR using the front switch on the Power Supply Module. Press the reset button on the Control Module front panel. At the prompt, hit a Carriage Return on the service computer to enter the test application mode. Using the user_id -ufield and the password motorola, login to the BR.2. Dekey the BR to verify that no RF power is being transmitted. Set the transmit DSP test mode to “stop.” At the field > prompt, type: NOTEThe following command keys the transmitter. Make sure that transmission only occurs on licensed frequencies or into an RF load. 3. Key the BR to 40 watts, following the steps below from the field > prompt: > login -ufieldpassword: motorolafield>field> power -otxch1 -p0 field> ptm -otx_all -mstopfield> dpm -otxch1 -mnonefield> dpm -otxch2 -mnonefield> dpm -otxch3 -mnonefield> dpm -otxch4 -mnone
54 68P80801H45-1   1/20/2002Troubleshooting EBTS System Manual - Vol 2QUAD Base Radio Station Verification Procedures 3.1 800 MHz QUAD: Set the frequency of transmit channel 1 through 4. 3.2 900 MHz QUAD: Set the frequency of transmit channel 1 through 4. 3.3 Enable the channels by setting a data pattern to “iden” NOTEAfter the following command is entered, power will be transmitted at the output of the Power Amplifier.field> freq -otxch1 -f860field> freq -otxch2 -f860.025field> freq -otxch3 -f860.05field> freq -otxch4 -f860.075field> freq -otxch1 -f935field> freq -otxch2 -f935.025field> freq -otxch3 -f935.05field> freq -otxch4 -f935.075field> dpm -otxch1 -midenfield> dpm -otxch2 -midenfield> dpm -otxch3 -midenfield> dpm -otxch4 -miden
68P80801H45-1   1/20/2002 55EBTS System Manual - Vol 2 TroubleshootingQUAD Base Radio Station Verification Procedures 3.4 Set the transmit power to 40 watts and key the BR.4. After keying the Base Radio, verify the forward and reflected powers of the station along with the station VSWR with the parameters listed in Table 2. NOTEThe reported value for forward power are not indicative of Base Radio performance. This value is reported from the internal wattmeter. These limits are only for verification of operation and are not representative of true operational power of the transmitter. 4.1 At the field > prompt, type:This command returns all active alarms of the Base Radio.Table 20    QUAD BR Transmitter ParametersParameter Value or RangeForward Power Greater than 36 WattsReflected Power Less than 2.0 WattsVSWR Less than 1.6:1field> ptm -otx_all -mdnlk_framedfield> power -otxch1 -p40field> power -otx_all
56 68P80801H45-1   1/20/2002Troubleshooting EBTS System Manual - Vol 2QUAD Base Radio Station Verification Procedures 4.2 At the field > prompt, type: If the alarms command displays alarms, refer to the System Troubleshooting section of this manual for corrective actions.5. View the spectrum of the transmitted signal on the R2660 Communications Analyzer in the Spectrum Analyzer mode. Figure 5 and Figure 6 shows a sample of the 800MHz and 900MHz spectrum, respectively. field> alarms -ofault_hndlrFigure 5 800 MHz Quad Carrier Spectrum
68P80801H45-1   1/20/2002 57EBTS System Manual - Vol 2 TroubleshootingQUAD Base Radio Station Verification Procedures 6. Dekey the BR to verify no RF power is being transmitted. Set the transmit DSP test mode to “stop.” At the field> prompt, type: Equipment DisconnectionUse the following steps to disconnect equipment after verifying the transmitter. 1. Remove power from the Base Radio by setting the Power Supply rocker switch (located behind the front panel of the Power Supply) to the OFF (0) position.2. Disconnect the RS-232 cable from the connector on the service computer.3. Disconnect the other end of the RS-232 cable from the RS-232 connector located on the front panel of the BRC.Figure 6 900 MHz Quad Carrier Spectrumfield> power -otxch1 -p0field> ptm -otx_all -mstopfield> dpm -otxch1 -mnonefield> dpm -otxch2 -mnonefield> dpm -otxch3 -mnonefield> dpm -otxch4 -mnone
58 68P80801H45-1   1/20/2002Troubleshooting EBTS System Manual - Vol 2QUAD Base Radio Station Verification Procedures CAUTION!CAUTION!Make sure power to BR is OFF before disconnecting transmitter RF connectors. Disconnecting transmitter RF connectors while the BR is keyed may result in RF burns from arcing.4. Disconnect the test cable from the PA OUT connector located on the backplane of the Base Radio.5. Connect the standard equipment cable to the PA OUT connector.6. Disconnect the 10 dB attenuator from the other end of the test cable. 7. From the attenuator, disconnect the cable to the R2660 Communications Analyzer.8. Restore power to the Base Radio by setting the Power Supply rocker switch to the ON (1) position.9. If necessary, continue with the Receiver Verification Procedure.
68P80801H45-1   1/20/2002 83EBTS System Manual - Vol 2 TroubleshootingQUAD Channel BR Backplane QUAD Channel BR BackplaneBackplane ConnectorsThe Base Radio backplane includes all external equipment connections. Table 21 lists and describes the backplane connectors.Table 21    QUAD BR Backplane ConnectorsConnector Module Description Connector TypeP1 EXBRC Signal 168 Pin AMP Z-Pack FuturebusP2 RX1 Signal 72 Pin AMP Z-Pack FuturebusP3  RX1 RF 6 coax Harting HarpakP4 RX2 Signal 72 Pin AMP Z-Pack FuturebusP5 RX2 RF 6 coax Harting HarpakP6 RX3 Signal 72 Pin AMP Z-Pack FuturebusP7 RX3 RF 6 coax Harting HarpakP8 RX4 Signal 72 Pin AMP Z-Pack FuturebusP9 RX4 RF 6 coax Harting HarpakP10 PA Signal 96 Pin EUROP11 PS Signal & Power  78 Pin AMP TeledensityP12aa. P12 is a cutout in the backplane with threaded inserts for securing the connector which mates directly to the power supply. PS -48 Vdc Power In 8 Pin AMP 530521-3P13 EX RF(EX from PA) SMA blindmateP14 EX RF(EX to PA) SMA blindmateP15 External / EXBRC Ethernet BNC blindmateP16 External / PA RF (PA from EX) SMA blindmateP17 External / PA RF (PA to EX) SMA BlindmateP18 External / PA TX Output SMA blindmateP19 RX Branch 1 RF SMAP20 RX Branch 2 RF SMAP21 RX Branch 3 RF SMAP22bExternal RS232 Dsub-9P23 External Alarm Dsub-25P24 External 5MHz/1PPS BNC
84 68P80801H45-1   1/20/2002Troubleshooting EBTS System Manual - Vol 2QUAD Channel BR Backplane Figure 9 shows the locations of the QUAD Base Radio external connections.QUAD BR Backplane Connector PinoutsTable 22 lists the pin-outs for the Base Radio Controller board’s 168-pin P1 connector. b. P22 will not be placed on the backplane. However, the backplane shall be designed with P22 to allow for reuse on future products.Table 22    EXBRC P1 Pinout, Signal and PowerRow A B C D1 GND 3.3 Vdc 3.3 Vdc NC2 GND 3.3 Vdc 14.2 Vdc 14.2 Vdc3 GND 3.3 Vdc 14.2 Vdc 14.2 Vdc4 GND GND GND GND5NCNCNCNCEX OUTPA INETHERNETPA FBDC POWERAC POWERRS 232 ALARMRX 1(RED)RX 2(GRN)RX 3(YEL)5MHZ/1 PPSPA OUTGROUNDEBTS327Q112501JNMRE BLACKThis port must be terminated by 50Ω load when configured for2 Branch Diversity. Also, the rx_fru_config parameter must be set to R12.**EX FBFigure 9 QUAD Base Radio Backplane Connectors
68P80801H45-1   1/20/2002 85EBTS System Manual - Vol 2 TroubleshootingQUAD Channel BR Backplane 6 GND GND GND GND7 GND 16.8MHz_RX 16.8MHz_RX_RTN GND8 GND GND GND GND9 GND 5 MHz/1 PPS 3.3 Vdc 3.3 Vdc10 NC NC NC 3.3 Vdc11 TxD CTS DTR BRG12 RTS RxD DSR CD13 NC NC NC 3.3 Vdc14 NC NC SHUTDOWN_ SLEEP_15 PA_ENABLE NC 28.6 Vdc 14.2 Vdc16 NC NC NC 3.3 Vdc17 EXT_GPI_1_ EXT_GPI_2_ EXT_GPO_1_ EXT_GPO_2_18 BAT_STAT_ MTR_STAT_ EXT_VFWD EXT_VREV19 SPI_M3 SPI_M2 SPI_M1 SPI_M020 SPI_ENABLE SPI_MOSI SPI_MISO SPI_CLK21 SPI_A2 SPI_A1 SPI_A0 WP_22 NC RxRESET_ NC NC23 NC Clock_SyncB_ NC NC24 GND GND 3.3 Vdc 3.3 Vdc25 SSI_Data_D SSI_CLK_D SSI_FS_D 3.3 Vdc26 SSI_Data_D_RTN SSI_CLK_D_RTN NC 3.3 Vdc27 GND GND 3.3 Vdc 3.3 Vdc28 DSPIb_MOSI DSPIb_CLK DSPIb_EN_1 DSPIb_EN_229 DSPIb_MOSI_RTN DSPIb_CLK_RTN DSPIb_EN_3 NC30 GND GND 3.3 Vdc 3.3 Vdc31 GND SSI_Data_C SSI_CLK_C SSI_FS_C32 GND SSI_Data_C_RTN SSI_CLK_C_RTN NC 33 NC Clock_SyncA_ NC NC34 GND GND 3.3 Vdc 3.3 Vdc35 SSI_Data_B SSI_CLK_B SSI_FS_B 3.3 Vdc36 SSI_Data_B_RTN SSI_CLK_B_RTN NC 3.3 Vdc37 GND GND 3.3 Vdc 3.3 Vdc38 DSPIa_MOSI DSPIa_CLK DSPIa_EN_1 DSPIa_EN_239 DSPIa_MOSI_RTN DSPIa_CLK_RTN DSPIa_EN_3 NC40 GND GND 3.3 Vdc 3.3 Vdc41 GND SSI_Data_A SSI_CLK_A SSI_FS_A42 GND SSI_Data_A_RTN SSI_CLK_A_RTN NCTable 22    EXBRC P1 Pinout, Signal and PowerRow A B C D
86 68P80801H45-1   1/20/2002Troubleshooting EBTS System Manual - Vol 2QUAD Channel BR Backplane Table 23    EXBRC P13 Pinout, Exciter from PACoaxial DescriptionCenter PA INOuter GNDTable 24    EXBRC P14 Pinout, Exciter to PACoaxial DescriptionCenter PA FeedbackOuter GNDTable 25    EXBRC P15 Pinout, EthernetCoaxial DescriptionCenter EthernetOuter GND
68P80801H45-1   1/20/2002 87EBTS System Manual - Vol 2 TroubleshootingQUAD Channel BR Backplane RX1 ConnectionsTable 26    RX1 P2 Pinout, Signal and PowerRow A B C D1 NC GND GND Clock_SyncA_2 GND DSPIa_MOSI_RTN DSPIa_CLK_RTN DSPIa_EN_13 GND DSPIa_MOSI DSPIa_CLK DSPIa_EN_24 GND GND GND GND5 14.2 SSI_CLK_A_RTN SSI_FS_B SSI_CLK_B_RTN6 14.2 SSI_CLK_A SSI_FS_A SSI_CLK_B7 14.2 GND GND GND8 14.2 SSI_Data_A_RTN GND SSI_Data_B9 GND SSI_Data_A GND SSI_Data_B_RTN10 GND NC NC NC11 3.3 RxRESET_ GND (ID0) GND (ID1)12 3.3 WP_ SPI_A0 SPI_A113 3.3 SPI_MISO SPI_CLK SPI_A214 GND SPI_M0 SPI_ENABLE SPI_MOSI15 GND SPI_M1 SPI_M2 SPI_M316 GND GND GND NC17 GND 16.8MHz_RX GND NC (WB switch)18 GND 16.8MHz_RX_RTN GND NC (MC switch)Table 27    RX1 P3 Pinout, RF Input and Output ConnectionRow A B C D E1 GND - GND - GND2 - RX3_EXP3 - RX1_EXP3 -3 GND - GND - GND4 GND - GND - GND5 - RX2_EXP2 - RX1_EXP2 -6 GND - GND - GND7 GND - GND - GND8 - RX Branch 1 - RX1_EXP1 -9 GND - GND - GND
88 68P80801H45-1   1/20/2002Troubleshooting EBTS System Manual - Vol 2QUAD Channel BR Backplane RX2 ConnectionsTable 28    RX2 P4 Pinout, Signal and PowerRow A B C D1 NC GND GND Clock_SyncA_2 GND DSPIa_MOSI_RTN DSPIa_CLK_RTN DSPIa_EN_33 GND DSPIa_MOSI DSPIa_CLK DSPIa_EN_24 GND GND GND GND5 14.2 SSI_CLK_B_RTN NC NC6 14.2 SSI_CLK_B SSI_FS_B NC7 14.2 GND GND GND8 14.2 SSI_Data_B_RTN GND NC9 GND SSI_Data_B GND NC10 GND NC NC NC11 3.3 RxRESET_ NC (ID0) GND (ID1)12 3.3 WP_ SPI_A0 SPI_A113 3.3 SPI_MISO SPI_CLK SPI_A214 GND SPI_M0 SPI_ENABLE SPI_MOSI15 GND SPI_M2 SPI_M1 SPI_M316 GND GND GND NC17 GND 16.8MHz_RX GND NC (WB switch)18 GND 16.8MHz_RX_RTN GND NC (MC switch)Table 29    RX2 P5 Pinout, RF Input and Output ConnectionRow A B C D E1 GND - GND - GND2 - RX3_EXP2 - RX2_EXP3 -3 GND - GND - GND4 GND - GND - GND5 - RX1_EXP1 - RX2_EXP2 -6 GND - GND - GND7 GND - GND - GND8 - RX Branch 2 - RX2_EXP1 -9 GND - GND - GND
68P80801H45-1   1/20/2002 89EBTS System Manual - Vol 2 TroubleshootingQUAD Channel BR Backplane RX3 ConnectionsTable 30    RX3 P6 Pinout, Signal and PowerRow A B C D1 NC GND GND Clock_SyncB_2 GND DSPIb_MOSI_RTN DSPIb_CLK_RTN DSPIb_EN_13 GND DSPIb_MOSI DSPIb_CLK DSPIb_EN_24 GND GND GND GND5 14.2 SSI_CLK_C_RTN SSI_FS_D SSI_CLK_D_RTN6 14.2 SSI_CLK_C SSI_FS_C SSI_CLK_D7 14.2 GND GND GND8 14.2 SSI_Data_C_RTN GND SSI_Data_D9 GND SSI_Data_C GND SSI_Data_D_RTN10 GND NC NC NC11 3.3 RxRESET_ GND (ID0) NC (ID1)12 3.3 WP_ SPI_A0 SPI_A113 3.3 SPI_MISO SPI_CLK SPI_A214 GND SPI_M2 SPI_ENABLE SPI_MOSI15 GND SPI_M1 SPI_M0 SPI_M316 GND GND GND NC17 GND 16.8MHz_RX GND GND (WB switch)18 GND 16.8MHz_RX_RTN GND NC (MC switch)Table 31    RX3 P7 Pinout, RF Input and Output ConnectionRow A B C D E1 GND - GND - GND2 - RX1_EXP2 - RX3_EXP3 -3 GND - GND - GND4 GND - GND - GND5 - RX2_EXP1 - RX3_EXP2 -6 GND - GND - GND7 GND - GND - GND8 - RX Branch 3 - RX3_EXP1 -9 GND - GND - GND
90 68P80801H45-1   1/20/2002Troubleshooting EBTS System Manual - Vol 2QUAD Channel BR Backplane RX4 ConnectionsTable 32    RX4 P8 Pinout, Signal and PowerRow A B C D1 NC GND GND Clock_SyncB_2 GND DSPIb_MOSI_RTN DSPIb_CLK_RTN DSPIb_EN_33 GND DSPIb_MOSI DSPIb_CLK DSPIb_EN_24 GND GND GND GND5 14.2 SSI_CLK_D_RTN NC NC6 14.2 SSI_CLK_D SSI_FS_D NC7 14.2 GND GND GND8 14.2 SSI_Data_D_RTN GND NC9 GND SSI_Data_D GND NC10 GND NC NC NC11 3.3 RxRESET_ NC (ID0) NC (ID1)12 3.3 WP_ SPI_A0 SPI_A113 3.3 SPI_MISO SPI_CLK SPI_A214 GND SPI_M0 SPI_ENABLE SPI_MOSI15 GND SPI_M3 SPI_M2 SPI_M116 GND GND GND NC17 GND 16.8MHz_RX GND NC (WB switch)18 GND 16.8MHz_RX_RTN GND GND (MC switch)Table 33    RX4 P9 Pinout, RF Input and Output ConnectionRow A B C D E1 GND - GND - GND2 - RX1_EXP3 - NC -3 GND - GND - GND4 GND - GND - GND5 - RX2_EXP3 - NC -6 GND - GND - GND7 GND - GND - GND8 - RX3_EXP1 - NC -9 GND - GND - GND
68P80801H45-1   1/20/2002 91EBTS System Manual - Vol 2 TroubleshootingQUAD Channel BR Backplane PA ConnectionsTable 34    QUAD BR PA P10 Pinout, Signal and PowerRow A B C1 SPI_ENABLE GND 28.6 Vdc2 GND GND 28.6 Vdc3 SPI_A0 GND 28.6 Vdc4 GND GND 28.6 Vdc5 SPI_A1 GND 28.6 Vdc6 GND GND 28.6 Vdc7 SPI_A2 GND 28.6 Vdc8 GND GND 28.6 Vdc9 SPI_M0 GND 28.6 Vdc10 GND GND 28.6 Vdc11 SPI_M1 GND 28.6 Vdc12 GND GND 28.6 Vdc13 SPI_M2 GND 28.6 Vdc14 GND GND 28.6 Vdc15 SPI_M3 GND 28.6 Vdc16 GND GND 28.6 Vdc17 SPI_MISO GND 28.6 Vdc18 GND GND 28.6 Vdc19 SPI_MOSI GND 28.6 Vdc20 GND GND 28.6 Vdc21 SPI_CLK GND 28.6 Vdc22 GND 3.3 Vdc 28.6 Vdc23 WP* 3.3 Vdc 28.6 Vdc24 GND GND 28.6 Vdc25 PA_ENABLE GND 28.6 Vdc26 GND 14.2 Vdc 28.6 Vdc27 GND 14.2 Vdc 28.6 Vdc28 GND 14.2 Vdc 28.6 Vdc29 GND 14.2 Vdc 28.6 Vdc30 GND 28.6 Vdc 28.6 Vdc31 GND 28.6 Vdc 28.6 Vdc32 GND 28.6 Vdc 28.6 Vdc
92 68P80801H45-1   1/20/2002Troubleshooting EBTS System Manual - Vol 2QUAD Channel BR Backplane External Connections Table 35    EXBRC P16 Pinout, PA from ExciterCoaxial DescriptionCenter PA INOuter GNDTable 36    EXBRC P17 Pinout, PA to ExciterCoaxial DescriptionCenter PA FeedbackOuter GNDTable 37    EXBRC P18 Pinout, PA RF OUTCoaxial DescriptionCenter PA RF OUTOuter GNDTable 38    QUAD BR Backplane Coaxial and DCSignalP12 -48 Vdc PowerP13 EX OutP14 FeedbackP15 EthernetP16 PA InP17 PA FeedbackP18 PA RF OUTP19 RX Branch 1P20 RX Branch 2P21 RX Branch 3P24 5 MHz/1 PPS
68P80801H45-1   1/20/2002 93EBTS System Manual - Vol 2 TroubleshootingQUAD Channel BR Backplane Table 39    QUAD BR Backplane Alarm 25 Pin Dsub (P23)Alarm Signal1 EXT_GPI_1_2 EXT_GPO_1_3 GND4 EXT_GPI_2_5 EXT_GPO_2_678910 GND111213141516 GND17 BAT_STAT_18 MTR_STAT_19 EXT_VFWD20 EXT_VREV21 GND22 GND232425 GNDTable 40    QUAD BR Backplane RS-232 9 Pin Dsub (P22) RS-232 Signal1CD2RxD3 TxD4 DTR5 GND6 DSR7RTS8 CTS9 BRG*
94 68P80801H45-1   1/20/2002Troubleshooting EBTS System Manual - Vol 2QUAD Channel BR Backplane PS Connections-Table 41    QUAD PS Power and Signal (P11)Pin Description Pin Description Pin Description1 GND (Plug In) 31 3.3 Vdc 61 SPI_MOSI2 GND 32 GND 62 SPI_CLK3 GND 33 GND 63 N.C.4 28.6 Vdc 34 GND 64 N.C.5 28.6 Vdc 35 GND 65 N.C.6 28.6 Vdc 36 GND 66 N.C.7 28.6 Vdc 37 GND 67 SPI_A08 28.6 Vdc 38 GND 68 SPI_A19 28.6 Vdc 39 GND 69 SPI_M210 28.6 Vdc 40 GND 70 SPI_M311 28.6 Vdc 41 GND 71 SPI_M112 28.6 Vdc 42 GND 72 SLEEP_13 28.6 Vdc 43 GND 73 SPI_M014 28.6 Vdc 44 GND 74 WP_15 28.6 Vdc 45 GND 75 SPI_A216 14.2 Vdc 46 GND 76 GND17 14.2 Vdc 47 GND 77 GND18 14.2 Vdc 48 GND 78 GND19 14.2 Vdc 49 GND20 14.2 Vdc 50 GND21 14.2 Vdc 51 GND2 14.2 Vdc 52 GND23 14.2 Vdc 53 GND24 3.3 Vdc 54 NC (FAN CON-TROL)25 3.3 Vdc 55 N.C.26 3.3 Vdc 56 N.C.27 3.3 Vdc 57 SHUTDOWN_28 3.3 Vdc 58 NC (Power shar-ing)29 3.3 Vdc 59 SPI_ENABLE30 3.3 Vdc 60 SPI_MISO
68P80801H45-1   1/20/2002 95EBTS System Manual - Vol 2 TroubleshootingQUAD Channel BR Backplane Table 42    QUAD BR 48 Vdc Battery Power (P12)Pin Description Description Pin1 + BATTERY + BATTERY 52 + BATTERY + BATTERY 63 - BATTERY (RTN) - BATTERY (RTN) 74 - BATTERY (RTN) - BATTERY (RTN) 8
96 68P80801H45-1   1/20/2002Troubleshooting EBTS System Manual - Vol 2QUAD Base Radio Signals QUAD Base Radio SignalsTable 43 lists and describes signals for the QUAD Base Radio.Table 43    QUAD Base Radio Signal Descriptions Signal Name Description Special28.6 Vdc 28.6 Vdc output from PS14.2 Vdc 14.2 Vdc output from PS3.3 Vdc 3.3 Vdc output from PSGND Station GroundRX Branch 1 RX Branch 1 from RFDS 50 ΩRX Branch 2 RX Branch 2 from RFDS 50 ΩRX Branch 3 RX Branch 3 from RFDS 50 ΩRX1_EXP1 RX1 (branch 1) expansion output 1 50 ΩRX1_EXP2 RX1 (branch 1) expansion output 2 50 ΩRX1_EXP3 RX1 (branch 1) expansion output 3 50 ΩRX2_EXP1 RX2 (branch 2) expansion output 1 50 ΩRX2_EXP2 RX2 (branch 2) expansion output 2 50 ΩRX2_EXP3 RX2 (branch 2) expansion output 3 50 ΩRX3_EXP1 RX3 (branch 3) expansion output 1 50 ΩRX3_EXP2 RX3 (branch 3) expansion output 2 50 ΩRX3_EXP3 RX3 (branch 3) expansion output 3 50 Ω5 MHz/1 PPS 5 MHz/1 PPS reference to the BRCSPI_ENABLE Host Centric SPI EnableSPI_MISO Host Centric SPI MISOSPI_MOSI Host Centric SPI MOSISPI_CLK Host Centric SPI ClockSPI_A0 Host SPI Device Address Line A0SPI_A1 Host SPI Device Address Line A1SPI_A2 Host SPI Device AddressLine A2SPI_M0 Host SPI Module Address Line M0SPI_M1 Host SPI Module Address Line M1SPI_M2 Host SPI Module Address Line M2SPI_M3 Host SPI Module Address Line M3WP_ Write Protect (active low)PA_ENABLE Turns off PA bias with active lowSLEEP_ Sleep signal from PSSHUTDOWN_ PS reset line from BRCCD RS232 Carrier DetectRxD RS232 RX Data
68P80801H45-1   1/20/2002 97EBTS System Manual - Vol 2 TroubleshootingQUAD Base Radio Signals TxD RS232 TX DataDTR RS232 Data Terminal ReadyDSR RS232 Data Set ReadyRTS RS232 Request to SendCTS RS232 Clear to SendBRG Baud Rate GeneratorRxRESET_ Reset Signal to RX modules16.8MHz_RX 16.8 MHz reference to RX differential16.8MHz_RX_RTN 16.8 MHz reference to RX return differentialClock_SyncA_ Clock Sync signal to RX1 & RX2 For Abacus IIIClock_SyncB_ Clock Sync signal to RX3 & RX4 For Abacus IIISSI_Data_A RX Data from RX module 1 differentialSSI_Data_A_RTN RX Data from RX module 1return differentialSSI_Data_B RX Data from RX module 2 differentialSSI_Data_B_RTN RX Data from RX module 2 return differentialSSI_Data_C RX Data from RX module 3 differentialSSI_Data_C_RTN RX Data from RX module 3 return differentialSSI_Data_D RX Data from RX module 4 differentialSSI_Data_D_RTN RX Data from RX module 4 return differentialSSI_CLK_A RX Clock from RX module 1 differentialSSI_CLK_A_RTN RX Clock from RX module 1 return differentialSSI_CLK_B RX Clock from RX module 2 differentialSSI_CLK_B_RTN RX Clock from RX module 2 return differentialSSI_CLK_C RX Clock from RX module 3 differentialSSI_CLK_C_RTN RX Clock from RX module 3 return differentialSSI_CLK_D RX Clock from RX module 4 differentialSSI_CLK_D_RTN RX Clock from RX module 4 return differentialSSI_FS_A RX Frame Sync from RX module 1SSI_FS_B RX Frame Sync from RX module 2SSI_FS_C RX Frame Sync from RX module 3SSI_FS_D RX Frame Sync from RX module 4DSPIa_En_1 DSPa SPI RX1 Abacus enableDSPIa_En_3 DSPa SPI RX2 Abacus enableDSPIa_En_2 DSPa SPI RX1 & RX2 SGC enableDSPIb_En_1 DSPb SPI RX3 Abacus enableDSPIb_En_3 DSPb SPI RX4 Abacus enableDSPIb_En_2 DSPb SPI RX3 & RX4 SGC enableDSPIa_MOSI DSPa SPI MOSI differentialDSPIa_MOSI_RTN DSPa SPI MOSI return differentialDSPIb_MOSI DSPb SPI MOSI differentialTable 43    QUAD Base Radio Signal Descriptions (Continued)Signal Name Description Special
98 68P80801H45-1   1/20/2002Troubleshooting EBTS System Manual - Vol 2QUAD Base Radio Signals DSPIb_MOSI_RTN DSPb SPI MOSI return differentialDSPIa_CLK DSPa SPI Clock differentialDSPIa_CLK_RTN DSPa SPI CLK return differentialDSPIb_CLK DSPb SPI Clock differentialDSPIb_CLK_RTN DSPb SPI CLK return differentialMTR_STAT_ External Wattmeter StatusBAT_STAT_ Battery StatusEXT_VFWD External Wattmeter Forward meterEXT_VREV External Wattmeter Reflected meterEXT_GPO_1_ General purpose output 1EXT_GPO_2_ General purpose output 2EXT_GPI_1_ General purpose input 1EXT_GPI_2_ General purpose input 2NC Not connected reservedTable 43    QUAD Base Radio Signal Descriptions (Continued)Signal Name Description Special
68P80801H45-1   1/20/2002  1Acronyms Global Telecommunications  Solutions Sector 1301 E. Algonquin Road, Schaumburg, IL 60196AcronymsA/D Analog-to-DigitalAAmperes AC Alternating Current ACT activeADA Americans with Disabilities ActAGC Automatic Gain ControlAIC Ampere Interrupting CapacityAIS Alarm Indication Signal (Keep Alive)ANSI American National Standards InstituteASCII American National Standard Code for Information InterchangeASIC Application Specific Integrated CircuitAux auxiliaryavg averageAWG American Wire Gaugebd baudBDM Background Debug ModeBER Bit Error RateBERT Bit Error Rate TestBMR Base Monitor RadioBNC Baby “N” ConnectorBPV Bipolar VariationBR Base Radio BRC Base Radio Controller BSC Base Site Controller BTU British Thermal UnitBW bandwidthC/N + I Carrier Power to Noise + Interference RatioCC Control CabinetCD Carrier Detectcd change directoryCLK ClockCLT Controllercm centimeterCMOS Complementary Metal Oxide SemiconductorCPU Central Processing UnitCSMA/CD Carrier Sense Multiple Access withCollision DetectCTI Coaxial Transceiver InterfaceCTL Control (Base Radio Control)CTS Clear-to-SendD/A Digital-to-AnalogDAP Dispatch Application ProcessorDB-15 15-pin D-subminiatureDB-9 9-pin D-subminiaturedB DecibeldBc Decibels relative to carrierdBm Decibels relative to 1mWDC Direct CurrentDCE Data Circuit-Terminating EquipmentDCSPLY DC SupplyDDM Dual Device Moduledeg degreeDIN Deutsche Industrie-NormDIP Dual In-line Packagediv division
-268P80801H45-1   1/20/2002Acronyms EBTS System Manual - Vol 2 DMA Direct Memory Access DOP Dilution of PrecisionDRAM Dynamic Random Access MemoryDSP Digital Signal ProcessorDTE Data Terminal EquipmentDTTA Duplexed Tower-Top AmplifierDVM Digital Volt MeterE1 European telephone multiplexing standardEAS Environmental Alarm System E-NET EthernetEBTS Enhanced Base Transceiver SystemEGB Exterior Ground BarEIA Electronics Industry AssociationEMI Electro-Magnetic InterferenceEPROM Erasable  Programmable  Read  OnlyMemoryEEPROM Electronically Erasable Programmable Read Only MemoryERFC Expansion RF CabinetESI Ethernet Serial InterfaceESMR Enhanced Special Mobile RadioEX ExciterFB feedbackFCC Federal Communications CommissionFIFO First-In, First-OutFNE Fixed Network Equipmentfreq frequencyFRU Field Replaceable UnitGen 3 SC Generation 3 Site ControllerGFI Ground Fault InterrupterGND groundGPS Global Positioning SystemGPSR Global Positioning System ReceiverHDLC High-level Data LinkHSMR High Elevation Specialized Mobile RadioHSO High Stability OscillatorHVAC Heating/Ventilation/Air ConditioningHz HertzI/O Input/OutputIC Integrated CircuitiDEN integrated Dispatch Enhanced NetworkIEEE Institute of Electrical and Electronic EngineersIF intermediate frequency)iMU iDen Monitor Unitin inchesin injectioniSC integrated Site ControllerISA Industry Standard Architecturekg kilogramkHz kiloHertzLAN Local Area NetworkLANIIC Local Area Network Interface ICLAPD Link Access Procedure D-Channellbs poundsLDM Linear Driver ModuleLED Light Emitting DiodeLFM Linear Final ModuleLIU Line Interface UnitLLC Link Layer ControllerLNA Low Noise AmplifierLO Local OscillatorLOS Loss of SignalMAU Media Access Unitmax maximumMC MulticouplerMGB Master Ground BarMGN Multi-Grounded Neutral
68P80801H45-1   1/20/2002 -3EBTS System Manual - Vol 2 Acronyms MHz MegaHertzmin minimummin minuteMISO Master In/Slave Outmm millimeterMMI Man-Machine-InterfaceMOSI Master Out/Slave InMPM Multiple Peripheral ModuleMPS Metro Packet Switch MS Mobile Station ms millisecondMSC Mobile Switching CenterMSO Mobile Switching OfficeMST Modular Screw TerminalsmV milliVoltmW milliWattN.C. Normally ClosedN.O. Normally OpenNEC National Electric CodeNIC Network Interface Cardno. numberNTM NIC Transition ModuleNTWK NetworkOMC Operations and Maintenance Center OSHA Occupational Safety and Health ActPA Power AmplifierPAL Programmable Array LogicPC Personal ComputerPCCH Primary Control ChannelPDOP Position Dilution of PrecisionpF picoFaradPLL Phase Locked LoopP/N Part NumberP/O Part Ofppm parts per millionPPS Pulse Per SecondPS Power Supply PSTN Public Switched Telephone Network PVC Polyvinyl Chloridepwr powerQAM Quadrature Amplitude ModulationQRSS Quasi Random Signal SequenceQty QuantityR1 Receiver #1R2 Receiver #2R3 Receiver #3RAM Random Access MemoryRCVR ReceiverRef ReferenceRF Radio Frequency RFC RF CabinetRFDS RF Distribution SystemRFS RF SystemROM Read Only MemoryRPM Revolutions Per MinuteRSSI Received Signal Strength IndicationRTN ReturnRU Rack UnitRx ReceiveRXDSP Receive Digital Signal ProcessorSCI Serial Communications InterfaceSCON VME System ControllerSCRF Stand-alone Control and RF Cabinet (configuration)SCSI Small Computer System Interfacesec secondSGC Software Gain ControlSINAD Signal Plus Noise Plus Distortion to Noise Plus Distortion Radio
-468P80801H45-1   1/20/2002Acronyms EBTS System Manual - Vol 2 SMART Systems Management Analysis, Research and TestSPI Serial Peripheral InterfaceSQE Signal Quality EstimateSRAM Static Random Access MemorySRC Subrate Controller SRI Site Reference Industry standard   SRIB SMART Radio Interface BoxSRRC Single Rack, Redundant Controller (configuration)SRSC Single Rack, Single Controller (configuration)SS Surge SuppressorSSC System Status ControlSSI Synchronous Serial InterfaceST StatusSTAT StatusStd StandardS/W SoftwareT1 North american telephone mutiplexing standard   TB Terminal BoardTDM Time Division Multiplextelco telephone companySCON VME System ControllerTISIC TDMA Infrastructure Support ICTSI Time Slot InterfaceTSI Time Slot InterchangeTTA Tower-Top AmplifierTTL Transistor - Transistor LogicTx TransmitTXD Transmit DataTXDSP Transmit Digital Signal ProcessorTxlin Tranlin ICtyp typicalUL Underwriters LaboratoriesVVolts VAC Volts - alternating current VCO Voltage Controlled OscillatorVCXO Voltage Controlled Crystal OscillatorVDC Volts - direct current VFWD Voltage representation of Forward PowerVME Versa-Module EurocardVp-p Voltage peak-to-peakVREF Voltage representation of Reflected PowerVSWR Voltage Standing Wave RadioWWattWDT Watchdog TimerWP Write ProtectWSAPD Worldwide Systems and Aftermarket Products Division
68P80801H45-1 1/20/2002 1Global Telecommunications  Solutions Sector 1301 E. Algonquin Road, Schaumburg, IL 60196 Parts and SuppliersThis appendix contains recommended part numbers (p/n) and manufacturers for various hardware, tools, and equipment used during installation of the EBTS. Also contained in this appendix is other installation related information, such as determining types of wire lugs, lengths and sizes of various wires and cables, custom cabling information, and fuses. All suppliers and model numbers listed are recommended due to their proven performance record in previous installations. Motorola cannot guarantee the effectiveness of the installation or performance of the system when using other supplier parts. Addresses, phone numbers, fax numbers, and other information is presented for each of the recommended suppliers, when possible.NOTEIn some listings, phone number and address are for corporate or main sales office. Other sales locations may be available. Call number given or go to website for expanded listings.NOTEThis information is subject to change without notice.Surge ArrestorsTwo types of surge arrestors should be used in the EBTS site, including:❐AC Power and Telco❐Antenna Surge Arrestors
268P80801H45-1   1/20/2002Parts and Suppliers EBTS System Manual - Vol 2 AC Power and Telco Surge ArrestorsThe recommended AC Power and Telco surge arrestors are both manufactured by Northern Technologies. The model numbers are:❐AC Power - LAP-B for 120/240 single-phaseLAP-C for 208 Vac three-phase❐Telco -  TCS T1DNorthern TechnologiesP.O. Box 610Liberty Lake, WA 99019Phone:  800-727-9119Fax:  509-927-0435Internet:  www.north-tech.comAntenna Surge ArrestorsThe recommended antenna surge arrestors are manufactured by Polyphaser Inc. The following models are recommended:❐Base Monitor Radio antennas - ISS50NXXC2MA❐Base Radio antenna (800 MHz tower top amplifier only) - 094-0801T-A❐Base Radio antenna (800 MHz cavity combined, transmit only; up to 5 channels) - IS-CT50HN-MA❐Base Radio antennas (800 MHz duplexed) - IS-CT50HN-MA❐Base Radio antennas (900 MHz duplexed) - 097-0311G-A.2❐GPS antennas - 092-082-0T-A❐Lightning arrestor bracket kit - Contact your local Motorola Sales representative to order this kit❐Receive Tower Top amplifier - 094-0801T-A❐Tower top test port cable - IS-50NX-C2Polyphaser, Inc.P.O. Box 9000Minden, NV 89423-9000 Phone:  800-325-7170              702-782-2511Fax:  702-782-4476Internet: www.polyphaser.comMotorola has set up several kits that contain the necessary arrestors with proper mounting hardware for the various antenna configurations. Contact your local Motorola representative for these OEM kits.
68P80801H45-1   1/20/2002 3EBTS System Manual - Vol 2 Parts and Suppliers RF AttenuatorsSeveral RF attenuators are needed at a site to ensure proper receive adjustments. The attenuators are used at the LNA sites to offset the excess gain from the Tower Top amplifiers, to balance the receive path, and to attenuate the BMR signal path. Use the following specifications when choosing vendors:❐Specified frequency range❍800 MHz systems – requires attenuator specification to include 806-821 MHz range❍900 MHz systems – requires attenuator specification to include 896-901 MHz range❐1 dB increments❐0.5 dB accuracy or better❐Female N connector / Male N connectorAlan Industries, Inc.745 Green Way DriveP.O. Box 1203Columbus, IN 47202Phone:  800-423-5190              812-372-8869Fax:  812-372-5909Huber + Suhner, Inc.19 Thompson DriveEssex, VT 05451Phone:  802-878-0555Fax:  802-878-9880Internet: www.hubersuhnerinc.comJFW Industries, Inc.5134 Commerce Square DriveIndianapolis, IN 46237Phone:  317-887-1340Fax:  317-881-6790email:  JFW atten@aol.comPasternack EnterprisesP.O. Box 16759Irvine, CA 92713Phone: 714-261-1920Fax:  714-261-7451RF attenuators are also needed for test equipment. The attenuators must be used between frequency reference equipment, service monitors, and the Motorola EBTS equipment. The following attenuators should be used at the site during optimization:❐Female BNC connector / Male BNC connector, 10 dB attenuator (1 W) between the Rubidium Standard and the R2660 Communications Analyzer. Refer to the System Testing section.
468P80801H45-1   1/20/2002Parts and Suppliers EBTS System Manual - Vol 2 ❐Female BNC connector / Male BNC connector, 30 dB attenuator (1 W) between the Rubidium Standard and the R2660. Refer to the System Testing, section.Emergency GeneratorSeveral different sizes of generators are available. Determine the loading requirements of the site prior to ordering a generator. A recommended manufacturer of the emergency backup generator power system is:Generac CorporationP.O. Box 8Waukesha, WI 53187Phone:  414-544-4811Fax:  414-544-0770Portable Generator ConnectionThe recommended portable generator connection is the AJA200-34200RS, manufactured by Appleton Electric. Figure 1 is a view of a connector located on the building. An adapter may be required if local electrical standards conflict with the wiring configuration.An alternate supplier of the portable generator connection is the ARKTITE Heavy Duty Receptacle Model 80, Style 2, 200 Amps, manufactured by Crouse-Hinds.Cooper IndustriesCrouse-Hinds, Inc.P.O. Box 4999Syracuse, NY 13221Phone:  315-477-7000Fax:  315-477-5717Figure 1 Portable Generator ConnectorEBTS078061295JNM123HOTHOT NEUTRALGROUNDPOLARIZATIONRIB
68P80801H45-1   1/20/2002 5EBTS System Manual - Vol 2 Parts and Suppliers GPS Evaluation KitThe GPS evaluation kit (part number VPEVL0002) is available from Motorola Position and Navigation System Business.Motorola Position and Navigation System Business4000 Commercial AvenueNorthbrook, IL 60062Phone:  847-714-7329Fax:  847-714-7325GPS Antenna AmplifierThere are two recommended manufacturers of the GPS antenna amplifiers. The model numbers are:❐LA20RPDC-N (made by WR, Inc.) (Type 1)❐GA-12F-N (made by CTS Co.) (Type 2)WR, Inc.710A W. 4th StreetPueblo, CO 81003Phone:  800-463-3063              719-595-9880Fax:  719-595-9890Internet:  www.fleetpc.comemail:  gpsman@wr-inc.comCarl Tinch Sales (CTS) Co.811 S. Central Expressway #518Richardson, TX 75080Phone:  972-231-1322Fax:  972-231-3403
668P80801H45-1   1/20/2002Parts and Suppliers EBTS System Manual - Vol 2 Specifications Type 1 Type 2Dimensions 3.293” x 2” x 1” 1” Dia. x Approx. 6”Connectors Type N female, both ends Type N female, both endsGain 23 dB gain typical20 dB min.12 dB ± 2 dBNoise Figure  2.6 dB typical 4.0 dBVSWR < 2.2:1 <2:1Frequency Range 1575.42 ± 50 MHz 1575.42 ± 10 MHzFiltering Yes YesMaximum Input Power+ 13 dBm 0 dBmVoltage 4.5 - 15 VDC 4.5 - 15 VDCCurrent @ 5 V < 15 mA typical < 20 mAFigure 2 GPS Antenna AmplifiersEBTS126051094JNMTYPE 1TYPE 21"2"3 5/16"ANTENNARF INPUT+13dBM MAXVDC THRURECEIVER/ANT VOLTAGEApproximately 6"2"INPUT OUTPUT
68P80801H45-1   1/20/2002 7EBTS System Manual - Vol 2 Parts and Suppliers Site AlarmsThree types of alarms should be used in an EBTS site, including: ❐Intrusion Alarm❐Smoke Alarm❐Temperature AlarmIntrusion AlarmThe recommended intrusion alarm is the Sonitrol 29A.Sonitrol 211 N. Union Street, Suite 350Alexandria, VA 22314Phone: 800-326-7475Fax:  703-684-6612Internet:  www.sonitrol.comSmoke AlarmA recommended smoke alarm is the Sentrol 320CC. This smoke alarm provides a relay closure for the iMU alarm. These smoke detectors are available from many electrical wholesale distributors. For the location nearest you, call between 6 a.m. and 5 p.m. Pacific Standard Time and ask Sales for the location of the nearest EW (Electric Wholesale) distributor.Sentrol, Inc.12345 SW Leveton DriveTualatin, OR 97062Phone: 800-547-2556             503-692-4052Internet:  www.sentrol.comTemperature AlarmThe recommended temperature alarm is the Grainger #2E206 thermostat. This alarm is manufactured by Dayton Electronics and distributed by W.W. Grainger:W.W. GraingerLocations NationwidePhone:  800-323-0620 Fax:  800-722-3291Internet:  www.grainger.com
868P80801H45-1   1/20/2002Parts and Suppliers EBTS System Manual - Vol 2 Cabinet Mounting HardwareThe cabinet mounting hardware is site dependent and must be procured locally. Equipment CabinetsThe mounting hardware used to secure the Equipment Cabinets containing control and/or RF hardware must be able to provide 1545 pounds of retention force. ❐If the cabinets are to be secured to a concrete floor, 1/2" grade 8 bolts with anchors are recommended. ❐If the cabinets are to be secured to another type of floor, determine the appropriate mounting hardware.Power Supply RackThe Motorola offered Power Supply rack from Power Conversion Products is available in a standard and an earthquake rack.Power Conversion Products, Inc.42 East StreetP.O. Box 380Crystal Lake, IL 60039-0380Phone:  800-435-4872 (customer service)              815-459-9100Fax:  815-526-2524Internet: www.pcpinc.comIf the earthquake rack is used, it must be bolted to the floor using the 02100-13 High Performance Anchor Kit, consisting of:❐anchors (qty. 4)❐load sharing plates (qty. 2)❐large square washers (qty. 8)Hendry Telephone ProductsP.O. Box 998Goleta, CA 93116Phone:  805-968-5511Fax:  805-968-9561Internet:  www.hendry.comemail: mailbox@hendry.com
68P80801H45-1   1/20/2002 9EBTS System Manual - Vol 2 Parts and Suppliers Cable ConnectionsThe recommended manufacturer for all wire lugs used during EBTS installation is Thomas & Betts. All wire lug part numbers listed are for Thomas & Betts.Thomas & Betts1555 Lynnfield RoadMemphis, TN 38119Phone:  800-888-0211 (general information)              800-248-7774 (sales/technical support)NOTEDouble hole wire lugs are preferred, but single hole wire lugs can be used where mounting requirements dictate their use.Selecting Master Ground Bar LugsTable 1 identifies recommended part numbers for wire lugs used to connect chassis ground wiring to the master ground bar from each cabinet. Selecting Cabinet Ground LugsTable 2 identifies recommended part numbers for wire lugs used to connect chassis ground wiring to the grounding point of each cabinet. Table 1    Recommended Master Ground Bar LugsWire Size Wire Type Lug ColorDescription P/N †#2 AWG Stranded Brown Single 1/4” diameter hole 54107#2 AWG Stranded Brown Double 1/4” diameter hole, 5/8” center 54207#6 AWG Stranded Blue Single 1/4” diameter hole 54105#6 AWG Stranded Blue Double 1/4” diameter hole, 5/8” center 54205NOTE:  These lugs require the use of the TBM5-S crimping tool. † All part numbers are Thomas & Betts.Table 2    Recommended Junction Panel Ground LugsWire Size Wire Type Lug ColorDescription P/N †#2 AWG Stranded Brown Single 1/2” diameter hole 54145#6 AWG Stranded Blue Single 3/8” diameter hole E6-12 NOTE:  These lugs require the use of the TBM5-S crimping tool.† All part numbers are Thomas & Betts.
10 68P80801H45-1   1/20/2002Parts and Suppliers EBTS System Manual - Vol 2 Battery System ConnectionsThe cable loop length refers to the total length of wire within a given circuit. For example, the combined length of the -48 Vdc (hot) lead and the DC return lead equals the cable loop length. This would mean that a cabinet that needs 16 feet of wire between the batteries and Power Supply Rack has a total loop length of 32 feet.Determining Battery System Wire SizeThe wire size for the connection between the batteries and the Power Supply Rack is determined by the required wire length and the maximum allowable voltage drop. The voltage drop in the loop must be kept to below 200 mV. The wire selected should be UL approved and contain a high number of strands for flexibility.For a standard configuration, the Power Supply rack is located directly adjacent to the batteries with a cable loop length of 20 feet or less, which requires the use of a 4/0 wire. Table 3 shows recommended wire sizes for various loop lengths. Larger wire sizes may be used if the recommended sizes are not available. The recommended wire sizes are large enough to allow site expansion to a fully loaded site.Selecting Battery System LugsDepending on the wire size used and the manufacturer of the Batteries, different wire lugs are crimped onto the power cable ends. After the wire size has been determined from Table 3, verify the manufacturer of the Batteries (Dynasty or Absolyte). Two different battery systems are offered with the EBTS. The Dynasty system is a low to medium capacity, field expandable system supplied for smaller sites or sites with minimal backup hour requirements. This system is custom designed to Motorola specifications. The Dynasty system is manufactured by Johnson Controls:Table 3    Battery System Wire SizeLoop Length Wire size20 feet 4/0 (or 250 MCM)30 feet 350 MCM45 feet 500 MCM
68P80801H45-1   1/20/2002 11EBTS System Manual - Vol 2 Parts and Suppliers C & D Technologies900 East Keefe AvenueP.O. Box 591Milwaukee, WI 53212Phone:  414-967-6500Fax:  414-961-6506The Absolute IIP battery system is a heavy duty, high capacity battery system manufactured by GNB Technologies:GNB Technologies829 Parkview BoulevardLombard, IL 60148Phone:  800-872-0471              630-629-5200Fax:  630-629-2635Refer to Table 4 to determine the proper wire lug for the connection of that wire to the Power Supply rack.Refer to Table 5 to determine the proper wire lug for the connection to the batteries, based on the wire size and battery manufacturer. One column lists the selection for Dynasty and the other lists the selection for Absolyte IIP.Table 4    Power Supply Rack Connection LugsWire Size Cabinet Lug Crimp Tool Lug P/N †4/0  Double 3/8” hole, 1” center TBM5-S 54212250 MCM Double 3/8” hole, 1” center TBM8-S 54213350 MCM Double 3/8” hole, 1” center TBM8-S 54215500 MCM Double 3/8” hole, 1” center TBM8-S 54218† All part numbers are Thomas & Betts.Table 5    Battery Connection LugsWire SizeLug ColorDynasty Absolyte IIPDescription P/N Description P/N4/0  Purple Double 3/8” hole, 1” center 54212 Single 1/2” hole 54170250 MCM Yellow Double 3/8” hole, 1” center 54215 Single 1/2” hole 54113350 MCM Red Double 3/8” hole, 1” center 54218 Single 1/2” hole 54115500 MCM Brown Double 3/8” hole, 1” center 54220 Single 5/8” hole 54118
12 68P80801H45-1   1/20/2002Parts and Suppliers EBTS System Manual - Vol 2 Anti-Oxidant GreasesAny one of the following anti-oxidant greases are recommended for connections to the positive (+) and negative (-) terminals of the batteries:❐No-Ox❐OxGuard❐PenetroxIntercabinet CablingEthernet and alarm cables connecting to the junction panels of each cabinet are supplied with the system. These cables may not be suitable for every EBTS site. It may be necessary to locally manufacture cables for a custom fit. Information is provided for both supplied cables and custom cables.Supplied CablesThe cables listed in Table 6 are supplied with the system. The length of these cables should be sufficient if the considerations outlined in the Pre-Installation section are followed.Making Custom CablesIf custom Ethernet or 5 MHz cables must be locally manufactured, use the part numbers listed in Table 7 for ordering the required materials.Table 6    Supplied Inter-Cabinet CablingDescription Qty. P/N †120" long, N-type Male to N-type male cable 3 0112004B24108" long, BNC Male-to-BNC Male, RG400 cable2* 0112004Z29210" long, 8-pin Modular plug cable 1* 3084225N42186" long, PCCH redundancy control cable 1** 3082070X01Phasing Harness 1 0182004W04†  All part numbers are Motorola.* Per RF rack.**  Per Control rack.Table 7    Parts for Ethernet and 5 MHz CablesDescription Qty. P/N †Connector, BNC male  As required 2884967D01Cable, RG400         As required 3084173E01† All part numbers are Motorola.
68P80801H45-1   1/20/2002 13EBTS System Manual - Vol 2 Parts and Suppliers Table 8 lists the part numbers for custom alarm cables.Table 9 lists the part numbers for custom PCCH cables.Equipment Cabinet Power ConnectionsSelecting Power Connection LugsTable 10 identifies recommended part numbers for lugs used for power connections between the Power Supply rack and the Control and RF Cabinets. The maximum wire size accepted by the Control and RF Cabinets is 2/0. The Control and RF Cabinets use screw type compression connectors and do not require lugs.Table 8    Parts for Alarm CablesDescription Qty. P/N †Connector, 8-pin modular As required 2882349V01Cable, 8-wire As required Locally procured† All part numbers are Motorola.Table 9    Parts for Extending PCCH Redundancy Control CablesDescription Qty. P/N †186” long, PCCH redundancy control cable1* 3082070X018-pin male Telco to 8-pin male Telco extension cable, length: as neededAs required Locally procuredModular, 8-pin female-to-female adaptorAs required Locally procuredNOTE:  Motorola does not guarantee proper operation of system if longer PCCH cable is used.† All part numbers are Motorola.* Per Control rack.Table 10    Recommended Power Connection Lugs for Power Supply RackSize Lug Color Description P/N †2/0 Black Double 3/8” hole, 1” center 54210#2 AWG Brown Double 1/4” hole, 5/8” center 54207#4 AWG Gray Double 1/4” hole, 5/8” center 54206#6 AWG Blue Double 1/4” hole, 5/8” center 54205† All part numbers are Thomas & Betts.
14 68P80801H45-1   1/20/2002Parts and Suppliers EBTS System Manual - Vol 2 Determining Power Connection Wire SizeThe cable loop length refers to the total length of wire within a given circuit. For example, the combined length of the -48 Vdc (hot) lead and the DC return lead equals the cable loop length. This would mean that a cabinet which needs 16 feet of wire between the Power Supply rack and equipment cabinets has a total loop length of 32 feet.The wire size for the connection between the Power Supply rack and the equipment cabinets is determined by the required wire length and the maximum allowable voltage drop. The voltage drop in the loop must be kept to below 500 mV. The wire selected should be UL approved and contain a high number of strands for flexibility. Table 11 shows the recommended wire sizes for various loop lengths of the RF Cabinet. Table shows the recommended wire sizes for loop lengths of the Control CabinetFor a standard configuration, the equipment cabinets are located adjacent to the Power Supply rack with a cable loop length less than 35’.Each equipment cabinet has a total of four Power Supply Rack connections; two -48 Vdc (hot) and two DC return. Each equipment cabinet contains two separate power distribution systems. A single hot wire and a single return wire are used for each side of the bus. Two return leads provide redundancy and allow a uniform wire size to be used for all 48 Vdc power distribution system connections.Table 11    Power Connection Wire SizeLoop Length Wire Size25 feet or less #6 AWG25 to 40 feet #4 AWG40 to 60 feet #2 AWG60 to 130 feet 1/0 AWGNOTE: The wire sizes listed are large enough to allow full RF Cabinet Base Radio capacity.Table 12    Power Connection Wire Size for Control CabinetLoop Length Wire Size150 feet or less #6 AWG
68P80801H45-1   1/20/2002 15EBTS System Manual - Vol 2 Parts and Suppliers Other Recommended SuppliersThe following are the addresses of various suppliers for tools and equipment used during installation of the EBTS.Test Equipment❐PRFS Rubidium Frequency StandardBall Corp. Efratom Inc.3 ParkerIrvine, CA 92618-1696Phone: 800-EFRATOM (337-2866)             714-770-5000Fax:  714-770-2463Internet:  www.efratom.com❐Fluke 77 Digital MultimeterFluke CorporationP.O. Box 9090Everett, WA 98206-9090Phone:  425-347-6100Fax:  425-356-5116Internet:  www.fluke.comemail:  fluke-info@tc.fluke.comService ComputerA PC or Macintosh can be used for EBTS optimization and field service. The following are the minimum requirements:❐19,200 bps serial port❐one floppy drive❐communication software, such as Smartcomm II or Procomm PlusThe Test Mobile Application is only available for the Macintosh platform. Contact your local Motorola sales representative.
16 68P80801H45-1   1/20/2002Parts and Suppliers EBTS System Manual - Vol 2 Software❐PKZIP softwarePKWare Inc.9025 N. Deerwood DriveBrown Deer, WI 53223Phone:  414-354-8699Fax:  414-354-8559Internet:  www.pkware.com❐ProComm softwareQuarterdeck Select CorporationP.O. Box 18049Clearwater, FL 34622-9969Phone:  800-683-6696Fax:  813-532-4222Internet:  www.Qdeck.comSpare Parts OrderingMotorola Inc.America’s Part DivisionAttn:  Order Processing1313 E. Algonquin RoadSchaumburg, IL 60196Phone:  800-422-4210 (sales/technical support)Fax:  847-538-8198Newark ElectronicsCall for a local phone number in your area to order partsPhone: 800-463-9275 (catalog sales)             773-784-5100Fax:  847-310-0275Internet:  www.newark.com

Navigation menu