Motorola Solutions 89FC4827 Non Broadcast Transmitter User Manual Summit BR 800 Tx FCC Filing 3

Motorola Solutions, Inc. Non Broadcast Transmitter Summit BR 800 Tx FCC Filing 3

Exhibit D Users Manual per 2 1033 c3

APPLICANT: MOTOROLA EQUIPMENT TYPE: ABZ89FC4827 EXHIBIT D User / Operational Manual Operational or User’s Manual The manual should include instruction, installation, operator, or technical manuals with required ‘information to the users’. This manual should include a statement that cautions the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The manual shall include RF Hazard warning statements, if applicable. The instruction and service manual for this base radio are not published at this time. However, draft copy of available manual information has been assembled and has been included as part of this filing package. Upon request, published manuals will be sent to the commission and/or telecommunication certification body (TCB) as soon as they become available. All of the descriptions, block diagrams, and schematics that are included in this filing package are current as of the package submittal date. EXHIBIT DESCRIPTION D1-1 Manual Front Matter (Draft) D1-2 Specifications (Draft) D1-3 Field Replaceable Units and Orderable Parts (Draft) D1-4 Tune-Up Procedure (Draft) D1-5 Racking Configurations (Draft) D1-6 Functional Description / Operation of Modules (Draft)
APPLICANT: MOTOROLA EQUIPMENT TYPE: ABZ89FC4827 EXHIBIT D1-1 User / Operational Manual Manual Front Matter (Draft)
APPLICANT: MOTOROLA EQUIPMENT TYPE: ABZ89FC4827 EXHIBIT D1-1 User / Operational Manual Manual Front Matter (Draft, Continued)
APPLICANT: MOTOROLA EQUIPMENT TYPE: ABZ89FC4827 EXHIBIT D1-1 User / Operational Manual Manual Front Matter (Draft, Continued)
APPLICANT: MOTOROLA EQUIPMENT TYPE: ABZ89FC4827 EXHIBIT D1-1 User / Operational Manual Manual Front Matter (Draft, Continued)
APPLICANT: MOTOROLA EQUIPMENT TYPE: ABZ89FC4827 EXHIBIT D1-2 User / Operational Manual Specifications (Draft) General PerformanceModel T2003Number of Channels 16Frequency Generation SynthesizedH x W x D 5.25" x 19" x 16.5" (133x483x419mm)Weight 40 lbs (19 kg)Power RequirementsAC: 85-264 VAC, 47-63 Hz Standy 0.6A, Rated Power 5.4A @ 117 VACDC: 21.6 - 32 Volts DC Standy 1A, Rated Power 13A @ 28 VDCTemperature Range -30 to 60 °C (-22 to 140 °F)Input / Output Impedance 50 ohmsAntenna Connectors Tx / Rx N-TypeModes of Operation Half-Duplex / DuplexFrequency Bands 403 - 470 MHzInternal Frequency Stability 1.5 PPMExternal Reference Capable YesChannel Spacing 12.5 kHz, 25 kHzTransmitterFrequency Range 406.1-470 MHzRated Output Power 25 - 100 Watts, VariableIntermodulation Attenuation 40 dBAdjacent Channel Power -80 dBc (25 kHz) / -60 dBc (12.5 kHz)Wideband Noise (1 MHz) -152 dBc/HzRated System Deviation 5 kHz (25 kHz) / 2.5 kHz (12.5 kHz)Audio Distortion <3%FM Hum and Noise 50 dB (25 kHz) / 45 dB (12.5 kHz)Spurious Harmonic Emissions Attenuation 85 dBFCC Type AcceptanceFCC Identifier: Frequency Range Type Power OutputABZ89FC4827 406.1-470 MHz Transmitter Variable 25-100 WABZ89FR4828 406.1-470 MHz Receiver N/A
APPLICANT: MOTOROLA EQUIPMENT TYPE: ABZ89FC4827 EXHIBIT D1-3 User / Operational Manual Field Replaceable Units and Orderable Parts (Draft) Motorola provides the following approved accessories to improve the productivity of your base station / repeater. For a list of Motorola-approved accessories, visit the following web site: http://www.motorola.com/governmentandenterprise. MOTOTRBO MTR3000 Ordering Guideline Model Description T3000 MTR3000 Base Station/Repeater X340MT UHF 100W Power (403–470 MHz) X540MT UHF 100W Power (470–524 MHz) X182UL Duplexer, UHF 403–435 MHz X182UM Duplexer, UHF 435–470 MHz X182UN Duplexer, UHF 470–494 MHz X182UH Duplexer, UHF 494–512 MHz X265UL Preselector, UHF 380–435 MHz X265UM Preselector, UHF 435–470 MHz X265UH Preselector, UHF 470–524 MHz X676UL Dual Circulator, UHF (403–470 MHz) X676UH Dual Circulator, UHF (470–524 MHz) X371BA Antenna Relay Note: Antenna Relay is not compatible if ordering X182, Duplexer X189AA Power Cable, Europe X162AD Power Cable, UK X191AD Power Cable, Australia CA01520AA Power Cable, DC U178AB Cabinet Mount Hardware X153BA Rack Mount Hardware X347AF Manual Install and User CD X244AF Auxiliary System Cable X244AG Community Base Station/Repeater Panel Cable X244AH Phone Patch Cable C540AD System Connector Cable XA00032AA 12 inch Ethernet Cable CLN8665A 6 feet High speed USB cable HKLN4439_ MTR3000 Capacity Plus Software Upgrade Customer Replaceable Power Cables for Standalone Base Radio Part Number Description TRN7663A Power Cable, North America TRN7755A Power Cable, Continental Europe TTN5049A Power Cable, UK / Ireland TTN5103A Power Cable, Australia
APPLICANT: MOTOROLA EQUIPMENT TYPE: ABZ89FC4827 EXHIBIT D1-3 User / Operational Manual Field Replaceable Units and Orderable Parts (Draft) (Continued) MOTOTRBO MTR3000 Field Replaceable Units Model Description DLN6701_ 100W PA, UHF 403–470 MHz DLN6702_ 100W PA, UHF 470–524 MHz DLN6703_ Exciter, UHF 403–470 MHz DLN6704_ Exciter, UHF 450–524 MHz DLN6705_ Receiver, UHF 403–470 MHz DLN6706_ Receiver, UHF 450–524 MHz DLN6707_ AC/DC Power Supply DLN6719_ Station Control TCXO CLN8629 MOTOTRBO MTR3000 Installation and User CD X347AF Manual Install and User CD Note The Manual Install and User CD contains: • MOTOTRBO MTR3000 Installation and User Manual (Including MTR2000 to MTR3000 MOTOTRBO Upgrade Kit) • MOTOTRBO MTR3000 Basic Service Manual Microphones/Speakers Model Description GMMN4063 Noise Cancelling Mic 0185180U01 Cable For External Speaker HSN1006 Speaker Miscellaneous Accessories Model Description RRX4025 ISB50LNC2 Bulkhead Arrestor 125-100 RRX4032 T-1 ISB50 Series Round Member Mount RRX4021 Lightening / Surge Arrestor RRX4034 Lightening / Surge Arrestor (110/220V AC Line Surge Protector) TRN4589 Dual Line Suppressor 3083908X02 Cable, Field System Adapter CLN1317* Antenna Relay CLN1316** Antenna Relay For Preselector Note (*) Includes Antenna Relay and required cables for stations without X265, Preselector (**) Includes Antenna Relay and required cables for stations that include X265, Preselector CKN1039* Preselector Cable Kit CKN1040** Preselector Cable For Antenna Relay Note (*) Order this cable for stations without X371, Antenna Relay (**) Order this cable for stations with X371, Antenna Relay Cabinets/Racks and Hardware Model Description THN6700 12 inch Indoor Cabinet THN6701 30 inch Indoor Cabinet THN6702 46 inch Indoor Cabinet THN6752 30 inch Modular Rack (16 RK U) THN6753 45 inch Modular Rack (24 RK U) THN6754 52 inch Modular Rack (27 RK U) THN6788_ Slides Motorola Cabinet CLN6833_ Slides Non-Motorola Cabinet CLN6679_ Rack Mount Hardware
APPLICANT: MOTOROLA EQUIPMENT TYPE: ABZ89FC4827 EXHIBIT D1-4 User / Operational Manual Tune-Up Procedure (Draft) See the following manual excerpts (Chapter 9 and Chapter 12 of MOTOTRBO MTR3000 Base Station / Repeater, Basic Service Manual) for instruction on performing the field digital upgrade, operational verification, and programming / tuning. Adjustments are software controlled and are pre-set at the factory. Certain station operating parameters can be changed using Customer Programming Software (CPS), within predetermined limits. Examples include transmit / receiver operating frequencies and transmitter power level. After the base station / repeater and ancillary equipment have been mechanically installed, properly cabled, and power applied, the equipment must then be optimized; that is, before placing the base station / repeater in operation. The cable required is a standard “USB A to B” cable. Optimization is performed through the Customer Programming Software (CPS), kit number RVN5115. After the base station / repeater is operational, the base station / repeater’s codeplug data must be copied to a PC- compatible computer. Optimization involves the following tasks: 1. Reading the base station / repeater codeplug from the base station / repeater (this ensures a match between the base station / repeater serial number (resident in the codeplug) and the serial number (part of the customized base station / repeater codeplug data) that is written back to the base station / repeater (see task 5). 2. Customizing the base station / repeater codeplug and saving the data to the base station / repeater. 3. Aligning the base station / repeater for: - Modulation Limit - Speaker Level - Station Reference - MTR2000 PA Calibration - Receiver Squelch Adjust 4. Performing post-optimization procedures. 5. Writing the customized codeplug to the base station / repeater codeplug. For details on these tasks, refer to the Customer Programming Software (CPS) Online Help.
Chapter 9 MTR2000 MOTOTRBO Digital Upgrade9.1 OverviewThe MTR3000 platform supports a digital upgrade kit which allow customers with fielded analog MTR2000 radios to upgrade the station control module (SCM), Receiver and Exciter modules and migrate their radio to a digital MOTOTRBO product. These modules are not assembled together when it is shipped. An "upgraded Base Station/Repeater" is comprised of a new front bezel, new Exciter module, new Receiver module, new SCM module, and utilizing the remaining components from the MTR2000 Base Station/Repeater (BR). Existing peripherals that are being utilized for the MTR2000 BR can retrofit the MTR3000 BR once it is upgraded. There is no need to purchase a new Duplexer, Base Station/Repeater Preselector, External Dual Circulator or Antenna Relay. The MTR2000 MOTOTRBO Digital Upgrade allows a MTR2000 customer to migrate from analog to digital. The available digital systems are:• MOTOTRBO (2 slot TDMA digital over the air DMR standard) • MOTOTRBO Connect Plus • Capacity Plus• IP Site ConnectThe features that are upgradeable from MTR2000 are:• Air Interface/Conventional – Analog Conventional• Station Operation – Base Station Analog, Repeater Analog• Channel Configuration – Half Duplex, Full Duplex• Air Interface/Trunked – Analog Trunking (LTR and Passport)• Frequency – UHF 403–470 MHz• Transmitter Capability – 75/100 W Capability• Hardware Peripheral Compatibility – Base Station/Repeater Preselectors, Duplexer, External Dual Circulator/Isolator Tray, Antenna Relay, External Frequency Reference, Angus Battery ChargerThe information below is an overview for installing the station and ancillary equipment.• Unpacking and inspecting the equipment• Mechanically install the equipment at the site• Make necessary electrical and cabling connections:-Audio-GPIO- Ethernet• Perform Alignment• Perform Configuration• Perform a post-install functional checkout test to verify installationNote For the correct procedure in handling static-sensitive parts, refer to Section 13.4 on page13-2.Applicant: MotorolaEquipment Type: ABZ89FC4827Exhibit D1-4
9-2 MTR2000 MOTOTRBO Digital Upgrade: Unpacking9.2 UnpackingThis section describes the procedures to unpack the new front bezel, new SCM module, new Exciter and Receiver modules from the packaging prior to installing them. 9.2.1 Equipment Unpacking and Inspection9.2.1.1 IntroductionThe new front bezel, new Exciter module, new Receiver module and new SCM module may be shipped by either air freight or electronic van (as specified by customer), except where noted. Thoroughly inspect the equipment as soon as possible after delivery. If any part of the equipment is damaged during transit, immediately report the extent of the damage to the transportation company and to Motorola.9.2.1.2 Unpacking EquipmentThe new front bezel, new Exciter Module, new Receiver Module and new Station Control Module are packed in four separate boxes which are packed together in a common box. The individual boxes are cushioned between corrugated cardboard in a common box. Note Currently, the MTR2000 MOTOTRBO Digital Upgrade is limited to the high power (100W)UHF BR. Additionally, once the upgrade is performed, the wireline and Auxiliary I/O boardfunctionality will no longer be supported.To avoid damage to the parts, be sure to observe proper electrostatic discharge precautions when modules are removed from the station.Applicant: MotorolaEquipment Type: ABZ89FC4827Exhibit D1-4
MTR2000 MOTOTRBO Digital Upgrade: Unpacking 9-39.2.1.3 Analog to Digital Migration Path – Removal and Replacement1. Remove the MTR2000 station front bezel from its chassis locking clip by carefully pulling the bezel forward (Refer to Figure 9-1). Figure 9-1. Removing Front Bezel2. Disconnect the Exciter-to-PA Coaxial Cable and Rx Input Cable (Refer to Figure 9-2). By disconnecting the cables, the Exciter Module, Receiver Module, Station Control Module (SCM) are accessible.Figure 9-2. Removing RF cable3. Remove the two screws securing the Transceiver (SCM, Exciter, and Receiver modules) to the bottom plate. Pull forward on the cast knobs, carefully slide the assembly out of the station (Refer to Figure 9-3) and place it aside.Cast knobChassis locking clipApplicant: MotorolaEquipment Type: ABZ89FC4827Exhibit D1-4
9-4 MTR2000 MOTOTRBO Digital Upgrade: UnpackingFigure 9-3. Removing two screws securing the Transceiver Assembly4. Remove the Wireline and Auxiliary I/O Card(s) (if any are installed) as the card(s) will not be supported in an upgraded MTR2000.5. Secure the new Station Control Module (SCM), Exciter and Receiver Modules using the eight screws (Refer to Figure 9-4) supplied with the MTR2000 MOTOTRBO Digital Upgrade kit to form the new Transceiver Assembly.Figure 9-4. Putting together new SCM, Exciter and Receiver6. Slide the new Transceiver Assembly into the MTR2000 station (along the guide rails) to mate with the connector on the backplane.Applicant: MotorolaEquipment Type: ABZ89FC4827Exhibit D1-4
MTR2000 MOTOTRBO Digital Upgrade: New Connections 9-57. Secure the Transceiver Assembly to the bottom plate by fastening the screws in Step 3 (Refer to Figure 9-3).8. Reconnect the Exciter-to-PA Coaxial Cable and Rx Input Cable. 9.3 New Connections After the station equipment has been mechanically installed, connections must be made. This involves making the following new connections to:• J7 Backplane Connector to support the following analog third party boxes (If applicable)- Community Repeater Panel- Tone Remote Controller (Console Connection)- LTR Trunking Controller- Passport (NTS) Controller- Phone Patch- Deskset• Ethernet to support the following MOTOTRBO features- IP Site Connect (Multi Site)- RDAC- Connect Plus- Capacity Plus9.3.1 AUX ConnectorThe location of the AUX connector is located at the station rear panel. The following cables are the reference cables used for this connector:• Auxiliary System Cable, Part no. X244AG• System Connector Cable, Part no. C540AD9.3.2 System ConnectorFor details on the system connectors, refer to Chapter 6 : MTR3000 Backplane.9.3.3 Telephone Line ConnectionsFor details on the telephone line connections, refer to Chapter 6 : MTR3000 Backplane.9.3.4 Station Maintenance ConnectionsTable 9-1 on page 9-6 provides a description of the maintenance connections located on the front of the Station Control Module.Note 1. It is not recommended to perform a digital upgrade and use the upgraded station in analog mode as certain analog functionality will be lost. Refer to Product Planner for details.2. 14.2VDC power (Pin 20) and GPIO_9 (Pin 5) are not supported on an upgraded MTR2000 J7 backplane connector. If 12VDC power is required on an upgraded MTR2000, then it must be obtained from Pin32 of connector J5.Applicant: MotorolaEquipment Type: ABZ89FC4827Exhibit D1-4
9-6 MTR2000 MOTOTRBO Digital Upgrade: Operational Verification9.4 Operational VerificationAfter the station equipment has been mechanically installed and all electrical connections have been made, replace the new MTR3000 station front bezel by inserting one of the front bezel locking clip into corresponding latch on the station housing, and carefully pressing the bezel on the opposite side until the second locking clip snaps into place.9.4.1 Applying PowerBefore applying power to the station, make sure all modules are securely seated in the appropriate connectors on the backplane and that all RF cables are securely connected.Plug in the AC line cord that supplies power to the station Power Supply, or switch on the DC-breaker to a station with a DC power source to the Power Supply.9.4.2 Alignment and ConfigurationAfter the station and ancillary equipment have been mechanically installed, properly cabled, and power applied, the equipment must be optimized before placing the station in operation. Align with the Tuner application followed by configuration with the CPS application.9.4.3 Optimizing TasksRefer to Chapter 12 : MTR3000 Programming and Tuning for optimizing tasks.Table 9-1. Station Maintenance Connections on the SCMConnector Name Function Details5/10 MHz External Reference (J3008)For alignment and for receipt of external reference.Achieved automatically and does not require configuration in the CPS. This is a 50 Ω input that is compatible with a 2Vpp (min) to 5Vpp (max) sine or square wave.Service Speaker (J3010)1Output to Power Voice speakerAdjustable between 0 to 500 mV across 50 kΩ @60% system deviation. Audio signal appears between Pins 3 and 4 on the connector. Must use speaker type HSN1006 via adapter cable Part.No. 0185180U01.Microphone (J3000)1Local Microphone Input Use local microphone type GMMN4063 or equivalent. Modulation sensitivity for 60% system deviation is typically 56 mV rms. Note 1. Only work in analog mode.Note 1. The BR will be locked after alignment with the Tuner application. To unlock it, the codeplug must be read and then written to by the CPS application.2. The BR reference must be aligned as shown in Section 13.3.3 on page 13-2, before the BR is placed on the air.Applicant: MotorolaEquipment Type: ABZ89FC4827Exhibit D1-4
MTR2000 MOTOTRBO Digital Upgrade: Operational Verification 9-79.4.4 Verifying Radio OperationRefer to Chapter 11 : MTR3000 Performance Check or Testing for procedures to verify Exciter and Receiver circuitry operation.9.4.5 Verifying Proper OperationFor details in this section, refer to Table 1-9 on page 1-12.Applicant: MotorolaEquipment Type: ABZ89FC4827Exhibit D1-4
Chapter 12 MTR3000 Programming and Tuning12.1 IntroductionThis chapter provides an overview of the MOTOTRBO Customer Programming Software (CPS) for the MTR3000 and MTR2000 MOTOTRBO Digital Upgrade, as well as the MOTOTRBO Tuner application for use on Windows XPTM, Windows Vista Home PremiumTM or Windows Vista Business EditionTM 32 bit and 64 bit operating system. 12.2 Customer Programming Software SetupThe Customer Programming Software setup, shown in Figure 12-1 is used to program the base station/repeater. Refer to Figure 12-2 and Figure 12-3 for the actual connectors on the front and rear panels of the base station/repeater.Note Refer to the appropriate program on-line help files for the programming procedures.Note Refer to the appropriate program on-line help files for the programming procedures.Computer USB ports can be sensitive to Electronic Discharge. Employ proper ESD practices (wrist strap, grounding, etc.) and do not touch exposed contacts on cables when connected to a computer.Figure 12-1. Customer Programming Software Setup from Rear Accessory ConnectorFront PanelUSBACUSB120 / 240 VACStationTx Port(N-type Female)Rx Port(N-type Female)AUX (J7)DC28 VDCEither One or BothStandard Type “A” to Type “B” USB cable Rear PanelComputerApplicant: MotorolaEquipment Type: ABZ89FC4827Exhibit D1-4
12-2 MTR3000 Programming and Tuning: Customer Programming Software SetupFigure 12-2. Front view (without front bezel) of MTR3000 Base Station/RepeaterFigure 12-3. Rear view of MTR3000 Base Station/RepeaterUSB portAC connectorTx portRx portDC connectorApplicant: MotorolaEquipment Type: ABZ89FC4827Exhibit D1-4
MTR3000 Programming and Tuning: Base Station/Repeater Tuning Setup 12-312.3 Base Station/Repeater Tuning SetupA personal computer (PC), Windows TM operating system, and the MOTOTRBO Tuner application are required to tune the Station. To perform the tuning procedures, the base station/repeater must be connected to the PC and test equipment setup as shown in Figure 12-4.Figure 12-4. Base Station/Repeater Tuning Equipment Setup12.4 Tuning Setup (MTR2000 MOTOTRBO Digital Upgrade)12.4.1 MTR2000 Calibration Coefficient EntryThis feature is used to allow entry of the transmitter (Tx) output power coefficients of an MTR2000 Power Amplifier (PA) into the MTR3000 tuning codeplug. Since an upgraded MTR2000 Base Station/Repeater does not have its PA upgraded, its PA calibration coefficients must be entered into the tuning codeplug, as the non-upgraded MTR2000 PA does not have an Electrically Erasable Programmable Read-only Memory (EEPROM). The calibration coefficients, which exist on a sticker on the face plate, consist of two 7 digit hexadecimal numbers and two 6 digit hexadecimal numbers. The sticker itself is created and applied at the factory in which the PA was calibrated.12.4.1.1 Tuning Procedure1. Power the Station from either an AC or DC source.2. Launch the MOTOTRBO Tuner application on the computer.Note Section 12.4 only applies to an upgraded MTR2000. TransmitService Monitoror CounterWattmeter20 dB PadFront PanelACUSB120 / 240 VACStationTx Port(N-type Female)AUX (J7)DC28 VDCEither One or BothRear PanelStandard Type “A” to Type “B” USB cableComputerUSBApplicant: MotorolaEquipment Type: ABZ89FC4827Exhibit D1-4
12-4 MTR3000 Programming and Tuning: Tuning Setup (MTR2000 MOTOTRBO Digital Upgrade)Figure 12-5. Tx Menu tree (Tuning Procedure)3. Select “Power” under the Tx menu in the tree view (Refer to Figure 12-5).4. Click the “Read” button in the Tuner to read the current code values from the radio’s tuning codeplug.- If the returned codeplug values match the PA calibration sticker values, click the directory tree to exit from the “Power” menu, or click the “Write” button to save the tuned power values into the radio’s codeplug.- If the retuned codeplug values do not match the PA calibration sticker value, proceed to Step 5 below. Otherwise, proceed to Step 9 to exit.5. Enter the upper left code from the PA calibration sticker to Code 1.6. Enter the upper right code from the PA calibration sticker to Code 2.7. Enter the lower left code from the PA calibration sticker to Code 3.8. Enter the lower right code from the PA calibration sticker to Code 4.9. Click the “Write” button to save the tuned power values into the radio’s codeplug.10. Exit from the Tuner application to reset the radio. After reset, the radio will be locked. 11. To unlock the radio, launch the CPS. Read the codeplug, then write to the codeplug.- CPS can be used to configure the codeplug prior to the write procedure (e.g. setting up frequency)12. Alignment is complete.Applicant: MotorolaEquipment Type: ABZ89FC4827Exhibit D1-4
MTR3000 Programming and Tuning: Modulation Limit Alignment 12-512.4.1.2 Verification or Test Procedure for High Power1. Power the Station from either an AC or DC source.2. Connect the radio’s Tx antenna port, through an attenuation pad and calibrate the path loss, to the Communication Analyzer.3. Via the CPS, program the radio with all user frequencies supported by the BR in analog mode.4. Enter the test frequency into the Communication Analyzer and set the analyzer in power meter mode.5. Connect a Mic to the RJ45 connector at the front panel.6. Press the PTT button on the Mic.7. Measure the transmit power.8. If the measured transmit power is not within the original MTR2000 specifications range, the PA must be replaced as it cannot be calibrated in the field.9. Repeat Step 4 to Step 7 for the remaining frequencies.12.5 Modulation Limit Alignment This feature is to set the modulation limit of the radio for MTR3000 and MTR2000 MOTOTRBO Digital Upgrade.12.5.1 Tuning Procedure (with no Tx Data and no PL)1. Connect the radio’s antenna port to the attenuation pad, if necessary, before connecting to the Communication Analyzer.2. Power the Station from either an AC or DC source.3. Apply a 1 kHz signal at 1.2Vrms to Pin 1 of the J7 backplane connector.- Signal ground is Pin 9 of the J7 backplane connector.4. Launch the Tuner application and click the “Read” button to read the softpot values.Note A modulation limit alignment is not needed if the radio is used in repeat mode. This isalways the case when the radio is in digital mode.Note 1. Under the “Accessories” menu within the CPS, if the “Audio Type” is set to “Rx & Tx Filtered Squelch” and the “Analog Accessory Emphasis” is set to “De & Pre”, then a modulation limite alignment is not needed. In this configuration, the modulation limit is always set to 92% RSD by the station software.2. If data or PL signaling is applied to Pin 13 of the J7 connector, proceed to Section 12.5.3 on page 12-7.Applicant: MotorolaEquipment Type: ABZ89FC4827Exhibit D1-4
12-6 MTR3000 Programming and Tuning: Modulation Limit Alignment5. Select “Modulation Limit” under the Tx menu in the tree view (Refer to Figure 12-6).Figure 12-6. Tx Menu tree (Tuning Procedure with no Tx data)6. Enter the tuning frequency into the Communication Analyzer (the value displayed on the Tuner GUI).7. Click the “PTT Toggle” button within the Tuner environment to key up the radio.8. Adjust the softpot value until the maximum deviation is 92% of the rated system deviation (RSD). This will be tested in a 12.5 kHz channel spacing, so 92% of 2.5 kHz is 2.3 kHz.9. Click the “PTT Toggle” button within the Tuner environment to de-key the radio.10. Click “Write” to save the new tuned softpot value into the radio’s codeplug.12.5.2 Verification (with no Tx Data and no PL)1. Connect the radio’s antenna port to the attenuation pad, if necessary, before connecting to the Communication Analyzer.2. Power the Station from either an AC or DC source.3. Via CPS, program the radio with any frequency within the specified range of the BR under test, and set the radio for low power and disable the repeat path.4. Apply a 1 kHz signal at 1.2Vrms to Pin 1 of the J7 backplane connector.- Signal ground is Pin 9 of the J7 backplane connector.5. Key up the radio and measure the deviation- Key the radio by grounding Pin 2 of the J7 backplane connector.- CPS must have Pin 2 configured as an active low with the PTT function.Note Set the modulation limit to 92% so that any additional deviation incurred by the transmitterVCOs over temperature is compensated for.Channel Spacing RSD 92% of RSD Tolerance12.5 kHz 2.5 kHz 2.3 kHz +0Hz / -50HzApplicant: MotorolaEquipment Type: ABZ89FC4827Exhibit D1-4
MTR3000 Programming and Tuning: Modulation Limit Alignment 12-76. De-key the radio.The deviation shall meet the limits shown in the table below.12.5.3 Tuning Procedure (with Tx Data or PL)1. Connect the radio’s antenna port to the attenuation pad, if necessary, before connecting to the Communication Analyzer.2. Turn on the Station using an AC or DC source.3. Click the “Read” button on the Tuner application to read the radio’s softpot values.4. Select “Modulation Limit” under the Tx menu in the tree view.5. Enter the tuning frequency into the Communication Analyzer (the value displayed by the Tuner application).6. Click the “PTT Toggle” button within the Tuner environment to key up the radio.7. Apply a 1 kHz signal at 1.2Vrms to Pin 22 of the J7 backplane connector.- Signal ground is Pin 9 of the J7 backplane connector.- If the manufacturer of the third party controller specifies that the Tx Audio is not to be pre-emphasized, use Pin 1 instead of Pin 22.8. Adjust the Modulation Limit softpot to a value that limits the maximum deviation to “X”% RSD, where “X” is equal to “92% RSD” minus “Tx Data’s % RSD”.E.g. If Tx Data deviation is equal to 17%, X = 92% - 17% = 75% as the maximum deviation limit.Figure 12-7. Example of maximum deviation limit calculation9. Click the “PTT Toggle” button within the Tuner environment to de-key the radio.Channel Spacing Relative Standard Deviation (RSD)92% of RSD Tolerance12.5 kHz 2.5 kHz 2.3 kHz +0Hz / -50Hz20.0 kHz 4.0 kHz 3.68 kHz +0Hz / -80Hz25.0 kHz 5.0 kHz 4.6 kHz +0Hz / -100HzNote The BR will be factory-tuned in accordance to the above procedure and specification.8%17%75%100%0%%RSD 92%With Tx Data or PLBufferData or PLVoiceApplicant: MotorolaEquipment Type: ABZ89FC4827Exhibit D1-4
12-8 MTR3000 Programming and Tuning: Modulation Limit Alignment10. Click “Write” to save the newly tuned softpot value into the radio’s codeplug.11. Alignment is complete.12.5.4 Verification (with Tx Data or PL)Refer to Section 12.5.2 on page 12-6 with the following exceptions:• The same Tx data signal level determined (obtained from Step 8 in Section 12.5.3 on page 12-7), is applied to Pin 13 during the validation process.• Pin 22 may be used instead of Pin 1, depending on the recommendation by the manufacturer of the third party controller.Note Refer to Figure 5-2 on page 5-5 for details regarding the audio and data flow.Note Set the modulation limit to 92% to compensate for any additional deviation incurred by thetransmitter VCOs over temperature.Applicant: MotorolaEquipment Type: ABZ89FC4827Exhibit D1-4
APPLICANT: MOTOROLA EQUIPMENT TYPE: ABZ89FC4827 EXHIBIT D1-5 User / Operational Manual Racking Configurations (Draft) There are various equipment racking configurations available to customers. The following section depicts some of the racking alternatives. Floor-Mount Cabinet The front, side and top views for all available floor-mount cabinets are shown below. Cabinet models and hardware are shown in the following table: Model Description THN6700 12 inch Indoor Cabinet THN6701 30 inch Indoor Cabinet THN6702 46 inch Indoor Cabinet THN6788 Motorola Cabinet Slides CLN6833 Non-Motorola Cabinet Slides See the installation manual for recommended equipment ventilation clearances. For improved access to the unit, tray slides are available as shown in the table above.
APPLICANT: MOTOROLA EQUIPMENT TYPE: ABZ89FC4827 EXHIBIT D1-5 User / Operational Manual Racking Configurations (Draft, Continued) Modular Racks The front, side and top views for all available floor-mount cabinets are shown below. The cabinet models and associated description are shown in the following table: Rack Model Description THN6752 30 inch Modular Rack (16 RK U) THN6753 45 inch Modular Rack (24 RK U) THN6754 52 inch Modular Rack (27 RK U) The side, top and bottom views for all available modular racks are shown below. The top and bottom plates are identical, and all dimensions and clearances are common to all racks. Recommended clearance front and rear is 91.44 cm (36 in) minimum for servicing access. Refer to Equipment Ventilation for recommended ventilation clearances. FRU kit CLN6679 (Rack Mount Hardware) is included with each rack model. This allows proper installation of the MTR3000 base station / repeater within the rack’s center of gravity. NOTE: This kit includes two rack mount standoffs and eight mounting screws.
APPLICANT: MOTOROLA EQUIPMENT TYPE: ABZ89FC4827 User / Operational Manual Functional Description / Operation of Modules (Draft) EXHIBIT D1-6 Base Radio Module Overview The Motorola MTR2003 / MTR3000 Base Station / Repeater (BR) provides a modular, flexible analog and digital station design for today's communication systems and of the future. The stations are available for use in Analog Conventional, Digital Conventional (MOTOTRBO), LTR Trunking, Passport Trunking, MOTOTRBO Capacity Plus Trunking, and MOTOTRBO Connect Plus Trunking configurations. The BR can either be configured as a stand-alone base station / repeater or as a base station / repeater connected to a back-end network, as in the case of operating in IP Site Connect mode. As a base station / repeater, it listens on one uplink frequency, and then re-transmits on a downlink frequency thus providing the RF interface to the field subscribers. When configured for analog station operation, the BR is designed to operate with most existing analog systems, therefore making a smooth migration to the MOTOTRBO system. When configured for digital operation, the BR offers additional services. The digital BR operates in TDMA mode, which essentially divides one channel into two virtual channels using time slots; therefore the user capacity is doubled. The BR utilizes embedded signaling to inform the field radios of the busy/idle status of each channel (time slot), the type of traffic, and even the source and destination information. Note: When configured in Digital Mode, the BR can only be used as a repeater. Note: At any given time, the BR either operates as a digital repeater or as an analog repeater. The BR is divided into functional modules that separate the frequency band specific and transmitter power specific circuits from other circuits and has separate modules for the control interface. These modules are self contained functional blocks with module-specific alarms. This design facilitates the field replaceable unit (FRU) concept of field repair to maximize system uptime. Indicators and Connections This section describes the LED indicators and connectors provided on the base station / repeater. The set of LEDs indicate the operational status of the base station / repeater. There are two sets of connectors for devices external to the base station / repeater: • One set connects to external devices to enable full operation of the base station / repeater. These are located at the back of the base station / repeater. • Another set connects to external devices for servicing the base station / repeater. These are located on the Station Control Module. LED Indicators A set of eight LEDs is located on the base station / repeater front bezel. The position of the eight LEDs on the front bezel is shown below. These LEDs indicate the status of the base station / repeater during normal operation. Front Bezel LEDs and Connectors After booting up the base station / repeater, the six LEDs (Power/Status, TX Slot 1, TX Slot 2, RX Slot 1, RX Slot 2 and the Mode LEDs) flashes in unison. The general status and condition of the MTR3000 Base Station / Repeater can be obtained by observing the eight LED indicators on the front bezel. The following tables show the LED symbols and their meaning and identify the information conveyed via the LED indicators.
APPLICANT: MOTOROLA EQUIPMENT TYPE: ABZ89FC4827 User / Operational Manual Functional Description / Operation of Modules (Draft) EXHIBIT D1-6 Front Bezel LED Indicators External Connections - Electrical Connections for the base station / repeater external connectors and line cord are located on the back panel and are shown below. Location of External Connectors at Rear of Base Station / Repeater The connection to external devices on the back panel is the J7 Auxiliary System Connector. The connector is a 25-pin connector used for connecting to an external device such as a trunking controller, tone remote adaptor, or phone patch. Service ports and LEDs are located on the front of the Station Control Module (SCM). The connection to external devices on the front of the station control module is the BNC connector. The connector allows the base station / repeater to be connected to a 5 MHz or 10 MHz external reference signal. The service ports include connectors for: • 5/10 MHz External Reference Signal • Ethernet Connector • Service Speaker Connector • USB Connector • Service Microphone Connector
APPLICANT: MOTOROLA EQUIPMENT TYPE: ABZ89FC4827 User / Operational Manual Functional Description / Operation of Modules (Draft) EXHIBIT D1-6 The locations of the connectors on the front of the station control module are shown below.
APPLICANT: MOTOROLA EQUIPMENT TYPE: ABZ89FC4827 User / Operational Manual Functional Description / Operation of Modules (Draft) EXHIBIT D1-6 Control Overview The heart of the Station Control Module (SCM) is the two Texas Instruments OMAP1710 processors. Each OMAP processor contains an ARM Host and a C55 DSP processor. One of these OMAP processor is dedicated to Receiver DSP operations, while the other OMAP provides for all other operations, including the transmitter functions. The SCM controls the entire coordination of the base station/repeater functions. Specifically, the SCM provides for the following functionalities: • Contains and runs the preloaded base station/repeater software • Manages inbound and outbound RF and Audio traffic • Provides external speaker and microphone ports • Provides an on-board USB port for local configuring, alignment and diagnostics via the following applications: - Customer Programming Software (CPS) - Tuner application - Repeater Diagnostic and Control (RDAC) software - Online Help • Provides an Ethernet port for IP site connectivity and remote RDAC • Provides GPIO connectivity for third party controller interfaces • Provides for analog base station/repeater audio connectivity • Data and Control to the Receiver via the SPI and SSI respectively • Data and Control to the Exciter via the SPI and SSI respectively • Control of the PA’s set power via the SPI • Generates the internal station reference • Provides control of the front panel status indicators
APPLICANT: MOTOROLA EQUIPMENT TYPE: ABZ89FC4827 User / Operational Manual Functional Description / Operation of Modules (Draft) EXHIBIT D1-6 Receiver Overview The Receiver Circuitry accepts receive RF signals from the site receive antenna, performs filtering and dual conversion, and outputs a digitized receive signal to the SCM. The receiver module has an on-board preselector. The receive signal is input from the site receive antenna to the receiver module, or to an external preselector filter (a separate assembly attached to the rear of the base station / repeater which provides highly selective bandpass filtering). The signal is fed through a low-pass filter, varactor tuned preselector, RF amplifier and image filter to the RF input of the first mixer. The filtered signal is mixed with an injection signal generated by the receive synthesizer / VCO, resulting in a first i-f (intermediate frequency) signal. The injection signal frequency is determined by frequency programming data from the SCM via the SPI bus. The specific frequency of the first i-f depends on the frequency band of the base station / repeater. The first i-f signal is filtered and input to a custom receiver IC. This component contains circuitry for generating the second injection signal, mixing down the first i-f to 2.25 MHz, amplification, and A/D (analog-to-digital) conversion of the second i-f signal, resulting in a digitized receive signal. This signal is fed as differential data to the SCM. The Receiver Module contains the following circuitry: • Frequency Synthesizer Circuitry – consists a phase-locked loop and Voltage-Controlled Oscillator (VCO), generates the first LO injection signal • Varactor-tuned Preselector Filter – provides bandpass filtering of the station Receiver RF input • Receiver Front End Circuitry – performs filtering, amplification, and the first down conversion of the Receiver RF signal • Custom Receiver IC Circuitry – consists a custom IC which performs the second down conversion, filtering, amplification, and analog-to-digital conversion of the receive signal • Analog to Digital Converter (ADC) Converter Circuitry – converts analog Receiver status signals to digital format for transfer, upon request, to the SCM • Local Power Supply Regulation – accepts +8V, +10V and +14.2V inputs and outputs +2.775V, +3.3V, +5V, +10V, and +14.2V operating voltages Input and Output Connections The following shows the Receiver module input and output external connections.
APPLICANT: MOTOROLA EQUIPMENT TYPE: ABZ89FC4827 User / Operational Manual Functional Description / Operation of Modules (Draft) EXHIBIT D1-6 Specifications The following table shows the specifications of MTR3000 Base Station / Repeater’s Receiver. Parameter Specification Frequency Ranges 403–470 MHz (UHF R1) or 450–524 MHz (UHF R2) Electronic Bandwidth Full Bandwidth (UHF R1 and R2) Analog Sensitivity 12 dB SINAD 0.257 μV (-118.8 dBm) Intermodulation Rejection 85 dB Adjacent Channel Rejection* 75 dB at 12 kHz, 80 dB at 25 kHz Spurious and Image Response Rejection 85 dB Intermediate Frequencies 1st: 73.35 MHz 2nd: 2.25 MHz RF Impedance 50 Ω Current Draw (Maximum) 0.04A from 14.2 VDC supply 0.52A from 10 VDC supply 0.11A from 8 VDC supply
APPLICANT: MOTOROLA EQUIPMENT TYPE: ABZ89FC4827 User / Operational Manual Functional Description / Operation of Modules (Draft) EXHIBIT D1-6 Exciter Overview The Transmitter Circuitry comprises two modules, the Exciter Module and the Power Amplifier (PA) Module. These modules combine to generate, modulate, and amplify the RF signal which is transmitted via the site transmit antenna. The Exciter Module interfaces directly to the Station Control Module (SCM), generates a modulated RF signal at the desired transmit frequency and sends this signal to the PA for amplification. The circuitry operates as follows. The transmit synthesizer and Voltage-Controlled Oscillator (VCO) circuitry on the Exciter Module accept frequency programming data from the SCM via the Serial Peripheral Interface (SPI) bus, and generate an RF carrier at the specified frequency. The VCO is directly modulated by transmit audio / data from the SCM. The resulting modulated RF signal (at a level of approximately +12 dBm) is then fed to the PA. The Exciter board contains the following circuitry: • Frequency Synthesizer Circuitry – consists of a phase-locked loop and Voltage-Controlled Oscillator (VCO), generates a modulated RF signal at the transmitter carrier frequency • RF Isolation Switch – allows the SCM to turn on/off the Exciter RF output signal to the power amplifier module • Analog to Digital Converter (ADC) Converter Circuitry – converts the analog Exciter status signals to the digital format for transfer, upon request, to the SCM • Local Power Supply Regulation/Filtering – accepts +8V, +10V and +14.2V inputs and provides +5V, +10V, and +12V operating voltages Input and Output Connections - The following shows the Exciter module input and output external connections. Specifications of Exciter Module Parameter Specification Frequency Ranges 403–470 MHz (UHF R1) or 450–524 MHz (UHF R2) Electronic Bandwidth Full Bandwidth (UHF R1 and R2) Output Power 10–14 dBm Current Draw (Maximum) 0.04A from 14.2 VDC supply 0.15A from 10 VDC supply 0.02A from 8 VDC supply Harmonics -20 dBc
APPLICANT: MOTOROLA EQUIPMENT TYPE: ABZ89FC4827 User / Operational Manual Functional Description / Operation of Modules (Draft) EXHIBIT D1-6 Power Amplifier Module Overview The Power Amplifier (PA) is a forced convection-cooled RF power amplifier. It accepts a low-level modulated RF signal from the Exciter Module and amplifies the signal for transmission via the site transmit antenna. The output power is continually monitored and regulated by a feedback and control loop, with a power output control voltage being generated by the transmitter control circuitry located on the PA Input/Output boards. Overview of Circuitry The Power Amplifier contains the following sub-circuits: • Intermediate Power Amplifier (IPA) – hybrid substrate amplifier stage which accepts low-level input from Exciter Module, amplifies the signal, and outputs a 0 W to 10 Watt RF signal • Final Module – hybrid substrate amplifier stage which accepts output from IPA Hybrid and provides final amplification to 100 Watts (maximum) • Directional Coupler/Power Detector/Low Pass Filter – couples amplified RF signal to transmit antenna connector; also generates dc voltages proportional to forward and reflected power for use in TX power control loop; provides harmonic suppression for the station • Single Circulator – provides isolation between Power Amplifier output and transmit antenna • Temperature Sense Circuitry – provides variable resistance signal proportional to heat sink temperature; signal is monitored by the PA power control circuitry Input and Output Connections The following shows the PA input and output external connections.
APPLICANT: MOTOROLA EQUIPMENT TYPE: ABZ89FC4827 User / Operational Manual Functional Description / Operation of Modules (Draft) EXHIBIT D1-6 The following table shows the specifications of MTR3000 Power Amplifier (PA). Specifications of Power Amplifier Parameter Specification Operational Frequency Range 403–435 MHz (R1) or 435–470 MHz (R2) Rated RF Output Power Range 25–100 W Rated RF Input Power Range 9.8–14 dBm 28.6V Supply Nominal Voltage (AC Power) 28.6V (+/- 4%) 14.2V Supply Nominal Voltage 14.2V (+/- 3%) 28.6V Supply Maximum Current Draw 12.6A 14.2V Supply Maximum Current Draw 2.0A Functional Theory of Operation A low-level modulated RF signal (approximately +13 dBm) from the Exciter Module enters the PA Input board via a coax cable. The signal is input to the IPA and amplified to approximately 0 to 10 W (depending on the dc power control voltage (V_CNTL) from the PA output board). The IPA output is then fed to the Dual Device Module for further amplification. The output of the DDM is then transferred to the circulator and then to the harmonic filter/coupler via the PA output board. The signal then exits from the Power Amplifier Module via an N-type coax connector. A single circulator is built into the Power Amplifier Module to provide isolation between the PA module and the transmit antenna. A thermistor mounted on the PA printed circuit board outputs a variable resistance proportional to the heat sink temperature. This signal is fed to the power control circuitry on the PA output board, which monitors the signal and reduces the PA output power (and enables a fan) if the PA temperature exceeds set limits. A feedback and control loop configuration is used to regulate the PA output power. The Directional Coupler generates a dc voltage proportional to the PA Module output power. This voltage is fed to power control circuitry on the PA output board where it is compared to reference voltages to generate a dc power control voltage. The Station Control Module sends current and power limit signals to a D/A converter (via the SPI bus) to control the maximum current/control voltage levels. The control voltage is fed to the IPA module where it controls the IPA output, thus controlling the overall output from the PA Module. Analog signals from various strategic operating points throughout the PA module are fed to an A/D converter, which converts them to a digital signal and, upon request by the Station Control Module, outputs the signal to the Station Control Module via the SPI bus. For example, the directional coupler generates a dc voltage proportional to the reflected power. This signal is converted to a digital signal and sent to the SCM. If the sense line indicates an impedance mismatch (high VSWR), the PA is either cut back in power or shut down completely.
APPLICANT: MOTOROLA EQUIPMENT TYPE: ABZ89FC4827 User / Operational Manual Functional Description / Operation of Modules (Draft) EXHIBIT D1-6 Power Supply Module Overview The Power Supply is described in this section. The information provided is sufficient to give service personnel a functional understanding of the module, allowing maintenance and troubleshooting to the module level. Refer to the service manual for Maintenance and Disassembly/Reassembly Procedures for detailed removal or installation procedures for all modules in the station. Over-current conditions on either the 28.6 VDC or 14.2 VDC outputs cause the total supply to shutdown and try to restart. If the over-current continues to exist, the power supply will ‘hiccup’ until the overload condition is removed, and will not be damaged by the overload. The 28.6 VDC output is protected by a primary current sense method such that its current limit point varies depending on the load on the other outputs at the time. The trip point for the 14.2 V and 5.1 V outputs is greater than 115% of the maximum current specified for the outputs. The power supply recovers automatically after the removal of the overload condition. The 28.6 V and 14.2 V outputs are protected from continuous over-voltages by detection circuits that cause the supply to shutdown and then try to restart itself. If the over-voltage condition continues to occur, the supply goes into a ‘hiccup’ mode of shutting down and trying to restart. If the over-voltage condition is removed, the supply automatically recovers. In addition, the 14.2 V and the 5 V outputs are protected by crowbar circuits. An AC Fail detect signal is provided to indicate (when used with battery backup option) that the power supply is operating from an external dc source rather than the ac mains. This signal is a TTL compatible output capable of sinking 1 mA, and is routed to the Station Control Module. The active-low state indicates ac operation. For the nominal 120 VAC operation, the signal is active-high impedance (indicating an ac mains failure) when the ac voltage is less than 85 Vrms, but more than the minimum voltage that guarantees that all outputs will be in regulation at full load. For the nominal 240 AC operation, the detect point is less than 170 Vrms but more than the minimum ac input voltage that guarantees that all outputs be in regulation at full load. The supply incorporates temperature sense/fan enable circuitry for controlling a 12VDC fan mounted on the surface of the heatsink assembly. The power supply circuitry senses the internal temperature of the power supply. When the internal temperature exceeds +60°C (± 5°C), +12 V is enabled at J1–1 to turn on the fan. The +12 V fan supply is derived from the +14.2 V output. Power to the fan is off when the temperature is below the set limit. The fan turns for approximately 5 seconds when power is first applied as a diagnostic indicator that the fan is functional. The power supply will turn off all outputs when an operational ambient temperature of +80°C (±2°C) has been reached with the supply operating at any input within its operating input voltage range (dc and ac). The following shows the electrical performance specifications for the power supply. Power Supply Module AC Performance Specifications: Parameter Value or Range Input Voltage Range 85 VAC to 264 VAC Operating Temperature –30° to +60° C (–22° to +140° F) Input Frequency Range 47 to 63 Hz Steady State Output Voltage 28.6 V @ 13 A, 14.2 V @ 8 A, 5.1 V @ 2 A Output Power (Rated) 500 W Output Ripple: +28.6 VDC +14.2 VDC +5.1 VDC 50 mV p-p, @ 25°C (77°F) 50 mV p-p, @ 25°C (77°F) 100 mV p-p, @ 25°C (77°F) Efficiency Greater than 75% (Full Load)
APPLICANT: MOTOROLA EQUIPMENT TYPE: ABZ89FC4827 User / Operational Manual Functional Description / Operation of Modules (Draft) EXHIBIT D1-6 Power Supply Module DC Performance Specifications: Parameter Value or Range Input Voltage Range 21.6 - 32 VDC Operating Temperature –30° to +60° C (–22° to +140° F) Steady State Output Voltage 28.6 V @ 13 A, Input Voltage Dependent 14.2 V @ 8 A, Regulated 5.1 V @ 2 A, Regulated Output Power (Rated) 500 W Output Ripple: +28.6 VDC +14.2 VDC +5.1 VDC Input Voltage Dependent, 0-0.5V below input 50 mV p-p, @ 25°C (77°F) 100 mV p-p, @ 25°C (77°F) Efficiency Greater than 75% (Full Load)

Navigation menu