Microsoft NSW-6NX Dual Band Tri Mode Non-Broadcast Cellular Transcei User Manual manual

Microsoft Mobile Oy Dual Band Tri Mode Non-Broadcast Cellular Transcei manual

UserManual.wiki >

Microsoft >

NSW 6NX User Manual

manual

Last modified 15-Mar-998860 User Guide Draftpre-release version 0.01

21. Safety At A GlanceRead these simple guidelines before using your phone. Failure to comply with these guidelines may be dangerous or illegal. For more detailed safety information, “Important Safety Information” on page 91.Road Safety Comes FirstDon’t use a hand-held phone while driving; park the vehicle first.Switch Off In HospitalsSwitch off your phone when near medical equipment. Follow any regulations or rules in force.Switch Off On AircraftMobile phones can cause interference. Using them on aircraft is illegal.Switch Off When RefuelingDo not use the phone at a refueling point. Do not use near fuels or chemicals.Switch Off Near BlastingDo not use the phone where blasting is in progress. Observe restrictions, and follow any regulations or rules in force.8860 UG version 0.01 3/15/99 3Safety At A GlanceInterferenceAll mobile phones may get interference which could affect performance.Use SensiblyUse only in the normal position (to ear). Avoid unnecessary contact with the antenna when phone is on.Qualified ServiceOnly qualified service personnel may install or repair cellular phone equipment. Accessories and BatteriesUse only approved accessories and batteries. Do not connect incompatible products.FCC/Industry Canada NoticeYour phone may cause TV or radio interference (e.g. when using a telephone in close proximity to receiving equipment). The FCC/Industry Canada can require you to stop using your telephone if such interference can not be eliminated. If you require assistance, contact your local service facility.This device complies with part 15 of the FCC rules. Operation is subject to the condition that this device does not cause harmful interference.

$6Press and hold the button at the top of the battery.Slide the battery toward the bottom of the phone.Lift the battery off the phone.Charging your new batteryYour phone can be used with either a rechargeable Li-Ion or NiMH battery. Note that a new battery’s full performance is achieved only after two or three complete charge and discharge cycles.With your phone on or off, connect the charger to a standard 120V AC outlet. Then connect the lead from the charger to the bottom of your phone or place it on a charging stand.When the battery begins charging, your phone will beep once and the battery strength indicator on the right side of the display will scroll.Note: If the battery is totally empty, it may take a few minutes before the charging indication appears on the display.If your phone displays1RWFKDUJLQJ, charging is suspended. Check that the battery is not connected to a non-approved charging device. If the battery is very hot or cold, wait for a while; charging will automatically resume after the battery is restored to its normal operating state. If charging still fails, contact your dealer. 8860 UG version 0.01 3/15/99 7Getting ConnectedWhen is a good time to charge?You can charge your battery anytime. If you have a NiMH battery, you should allow it to completely discharge once in a while.When your phone beeps once and displays %DWWHU\ORZ, you only have a couple of minutes of talk time remaining. The repetition rate of these battery-low warnings depend on the remaining battery capacity and the battery condition. These warnings are more frequent when you’re in a call.Note: The phone will not give you the warning tone under certain conditions. See “Warning tones” on page 81.Once all the power has drained from your battery, you’ll hear three beeps with the message 5HFKDUJHEDWWHU\ on your display. At this point, your phone will switch itself off and you’ll need to recharge your battery.When is charging complete?When the charge indicators stop scrolling, your phone is considered fully charged. However, a slight increase in charge may occur if your phone is left connected to the charger for a while. This is called “trickle charge.”Charging times depend on the type of battery and charger used. For approximate charging and operating times, see “Standby and Talk Times” on page 85.Can you make calls while charging?Yes, you can. But your battery may not charge while a call is in progress. Charging should resume once you end the call.Discharging NiMH batteriesA NiMH battery lasts longer and performs better if you fully discharge it from time to time. To discharge the battery, leave your phone switched on until the battery is drained. The phone will display several messages that the battery is low and that you need to recharge it; just ignore them. Do not attempt to discharge the battery by any other means.$

8Important Battery Information• Note that a new battery’s full performance is achieved only after two or three complete charge and discharge cycles!• The battery can be charged and discharged hundreds of times but it will eventually wear out. When the operating time (talk time and standby time) is noticeably shorter than normal, it is time to buy a new battery.• Use only batteries approved by the phone manufacturer and recharge your battery only with the chargers approved by the manufacturer. When a charger is not in use, disconnect it from the power source. Do not leave the battery connected to a charger for longer than a week, since overcharging may shorten its life. If left unused a fully charged battery will discharge itself over time.• (NiMH batteries only) For good operation times, discharge the battery from time to time by leaving your phone switched on until it turns itself off (or by using the battery discharge facility of any approved accessory available for your phone). Do not attempt to discharge the battery by any other means.• Temperature extremes will affect the ability of your battery to charge: allow it to cool down or warm up first.• Use the battery only for its intended purpose.• Never use any charger or battery which is damaged or worn out.• Do not short circuit the battery. Accidental short circuiting can occur when a metallic object (coin, clip, or pen) causes direct connection of the + and - terminals of the battery (metal strips on the back of the battery), for example when you carry a spare battery in your pocket or purse. Short circuiting the terminals may damage the battery or the connecting object.• Leaving the battery in hot or cold places, such as in a closed car in summer or winter conditions, will reduce the capacity and lifetime of the battery. Always try to keep the battery between 59º F and 77º F (15º C and 25º C). A phone with a hot or cold battery may temporarily not work, even when the battery is fully charged. NiMH batteries’ performance is particularly 8860 UG version 0.01 3/15/99 9Getting Connectedlimited in temperatures below 14º F (-10º C). Li-ion batteries’ performance is particularly limited in temperatures below 32º F (0º C).• Do not dispose of batteries in a fire!• Batteries must be recycled or disposed of properly. Must not be disposed of in municipal waste.

103. The BasicsYou have purchased a powerful phone, with lots of features. Read this section for some very basic information on how to use your phone. A more comprehensive description of your phone is covered in “Features A to Z” starting on page 21.Switching the phone on and offPress and hold the P key for two seconds to switch the phone on or off.Switching off with the P keyQuickly press the P key (6ZLWFKRII will appear, highlighted) then press 2..NORMAL POSITION: Hold the phone as you would any other telephone with the antenna pointed up and over your shoulder.TIPS ON EFFICIENT OPERATION: As with any other radio transmitting device, do not touch the antenna unnecessarily when the phone is switched on. Contact with the antenna affects call quality and may cause the phone to operate at a higher power level than otherwise needed.WARNING! Do not switch on the phone when wireless phone use is prohibited or when it may cause interference or danger.See “Safety At A Glance” on page 2 for more information.8860 UG version 0.01 3/15/99 11The BasicsGet a good signalYour phone operates on radio waves, and the quality of radio reception depends entirely on the strength of the radio signal in your area.This radio coverage is maintained by a wireless network and the quality of calls on a wireless phone depends on the strength of the wireless radio signal.Checking signal strengthWhen you are at the start screen (see page 16) or in a call, the signal strength is indicated by the indicators on the left side of your phone’s display. These indicators scroll as the strength of the signal increases and decreases.Increasing your phone’s signal may be easy. Try moving your phone slightly, or move towards a window if you’re calling from inside a building.Using the slideIf you activate the slide setting, you can answer and end calls simply by opening or closing the slide. Your phone will also prompt you to activate the keyguard once you close the slide.Activating and deactivating the slide settingPress 0HQX 4 2 6 (6HWWLQJV - 3KRQHVHWWLQJV - 6OLGHVHWWLQJ)Scroll to 2Q to activate the slide, or 2II to deactivate the slide and press 2.Note: If you’re using a headset and wish to close the keypad cover and still keep the call active, press once before closing the keypad cover.Making a callWhen you want to make a call, open the slide, enter the area code and phone number and press B

$12Editing a number on displayPress to move the cursor to the left and to move it to the right. Press &OHDU to delete the character to the left of the cursor.Dialing stored phone numbersView stored names and numbers by pressing or from the start screen (see page 16), then press BSee “Phone book” on page 57 for details on storing numbers.Calling card callsSee “Calling card” on page 29.Emergency callsSee “Emergency calls” on page 40.Ending a callIf 6OLGHVHWWLQJ is active, simply close the keypad cover. Otherwise, press E See “Using the slide” on page 11.Answering a callThe phone rings according to the settings in the currently selected profile (see page 61).If 6OLGHVHWWLQJ is active, simply open the slide to answer the call. Otherwise, press any key except E or PNote: If Keyguard is on (see page 13), only B answers calls. See “Using the slide” on page 11.8860 UG version 0.01 3/15/99 13The BasicsWant to stop your phone from ringing without answering the call ?Press P quickly when the phone rings. This keeps you from answering a call if it’s inconvenient to talk.You can still answer the call if &DOO or the name of the person who is calling is still flashing on your display. If you don’t wish to answer the call, it will be forwarded to your voice mailbox if you have a voice mail subscription.KeyguardThis feature helps to prevent accidental key presses (e.g. when your phone is in your pocket, in your purse) by locking your keypad. If any keys are pressed while Keyguard is activated, 3UHVV8QORFNDQGWKHQ will display.Using Keyguard with the slideWhen 6OLGHVHWWLQJ is activated, your phone will display /RFNNH\V in the lower left part of the display. Press the key underneath /RFNNH\V and your Keyguard will be activated.If you don’t wish to activate Keyguard at this time, press 4XLW or simply wait about five seconds and it will disappear.Keyguard will deactivate each time you open the slide.Activating Keyguard without the slideThere are three different ways to activate Keyguard. .H\VORFNHG will appear on the display when activated.• Press and hold E • Press ∗• Press 9 at the start screen$

14Deactivating Keyguard• Press then• Press and hold E until appears and press Note: When Keyguard is 21, calls to the emergency number programmed into your phone (e.g. by pressing 911 then B) may be possible. However, Emergency key 9 doesn’t work.Answering a call with Keyguard activeDuring an incoming call the keypad automatically unlocks. However, you can answer a call only by opening the keypad cover if it’s active; otherwise, press only B. After you end the call, Keyguard automatically becomes active again. Some notes about Keyguard• Calls may be possible to the emergency number programmed into your phone (e.g. 911 or other official emergency number). The number is displayed only after you have keyed in its last digit.• Pressing the P key quickly turns lights on for 15 seconds.Note: Keyguard is automatically turned off when the phone is connected to a car kit. 8860 UG version 0.01 3/15/99 15Using Your Phone4. Using Your PhoneThe first few days you have your phone, play with it to learn how the menu and submenu system works. The more you learn how to access these menus and submenus, the more fun you’ll have with your phone.This section describes the different methods of using your phone menus and submenus. The DisplaySoft keysYour phone has two softkeys located below the display. The current function is indicated by the texts appearing directly above them. Press the corresponding key under the choice you wish to select.This illustration shows the phone at the start screen (see “What is the ‘start screen’?” on page 16). The start screen always displays 0HQX on the left and 1DPHV on the right. 0HQX allows you to access your phone’s menus and submenus. 1DPHV allows you to access your phone book (see “Phone book” on page 57). Scroll keysYour phone has a scroll key located just below the display screen. The scroll key has two arrows on it that look like and . Press these to navigate through your phone’s menus and submenus, as well as through your phone book. (See “Phone book” on page 57).

$16Scroll barWhen you access your phone’s menu and submenus, you will notice a scroll bar at the far right of the screen. This bar indicates your location in the menu structure; each “tab” on the bar represents a different menu item.For example, press 0HQX once. The scroll bar appears with the first (top) tab displayed. A different tab appears each time you press the or key to move up and down through the menu structure. The scroll bar works the same way with submenus.Menu & submenu numberingWhen you scroll to a menu or submenu, the menu number and/or submenu number appears on the display above the scroll bar.For example, when you scroll to menu 2 (&DOOORJ) the number  appears in the top right-hand corner of the display. If you scroll to menu 4 (6HWWLQJV), submenu 3 (6HFXULW\VHWWLQJV), your phone will display  in the top right-hand corner.See “Summary of Menu Items” on page 17 for a list of your phone’s features along with their menu locations.Also, see “Using shortcuts” on page 17.What is the ‘start screen’?The start screen appears when you first turn your phone on, in its idle state.When you want to get to the start screen, press E at any time except during a call (unless you want to hang up).Note: If you press E when the phone is requesting input (i.e., a setting, phone number, name, etc.), the phone displays the start screen and the input is not saved.8860 UG version 0.01 3/15/99 17Using Your PhoneScrolling through the main menuPress 0HQX at the start screen. Then press or to reach the desired menu item.Press6HOHFW,2SWLRQVor2. (whichever appears) to enter submenus and to choose options.Press ([LW to exit the present menu or %DFN to go back one level.Using shortcutsThis is a quick and easy way to access a menu without having to scroll through other menus.Press 0HQX, then menu number, then submenu number.Press the menu and submenu numbers within a couple of seconds of each other when using this method.For a summary of your phone’s menu structure, see “Summary of Menu Items” on page 17.Help textIf you’re not sure how a feature works, wait just a few seconds and help text will appear for most of your phone’s features. Press 0RUH to see the next page of the text or %DFN to exit.Summary of Menu Items1 Messages1 1 Text Messages1 1 1 Inbox$

204 2 5 7Chinese Traditional4 2 6Slide setting4 3Security settings4 3 1Restrict calls4 3 2Access codes4 4Network services4 4 1Voice privacy4 4 2Call forwarding4 4 3Call waiting4 4 4Send own number4 4 5Network feature setting4 4 6NAM selection5System5 1Automatic5 2Manual5 3New search6Games6 1Memory6 2Snake6 3Logic6 4Rotation7Calculator8Calendar9Keyguard 8860 UG version 0.01 3/15/99 21Features A to Z5. Features A to ZABC modeThis allows you to enter names into your phone book.See “Entering letters and numbers” on page 42.Access codes This is a security feature that allows you access to certain phone features, such as the phone lock (page 59) and unlocked phone number (page78). Also, see “Lock code” on page 49 and “Security code” on page 68.Alarm clock The alarm clock operates off your phone’s clock. The volume for the alarm clock is determined by the current ringing volume.Note: If you have selected the or ringing option (see page 64), your alarm clock will quietly beep one time. See “Clock” on page 36 for information on your phone’s clock.Setting the alarm clockPress 0HQX 4 2 2 (6HWWLQJV - 3KRQHVHWWLQJV - $ODUPFORFN)Enter time you wish to set alarm (use two-digit fields for hours and minutes). Existing digits will be replaced with the new alarm time.Press 2.

$24Calculator Your phone’s calculator adds, subtracts, multiplies, divides, and converts currency.Remember! Your phone must be switched on to use this feature. Do not switch on the phone when wireless phone use is prohibited or when it may cause interference or danger. Using the calculatorPress 0HQX 7 (&DOFXODWRU)Enter the first number in the calculation (press # for decimals) To add, press ∗ (+ appears) To subtract, press ∗∗ twice (- appears) To multiply, press ∗∗∗ (* appears) To divide, press ∗∗∗∗ ( / appears)To add a decimal, press the # keyEnter the second numberRepeat these steps as many times as needed. Press &OHDU to erase any mistakes.Press 2SWLRQV. With (TXDOVhighlightedpress 2.Note: You can also choose , , , and from the list of options.Storing exchange ratesPress 0HQX 7, then press 2SWLRQVScroll to ([FKDQJHUDWHand press 2.Press or at either +RZPDQ\KRPHXQLWVWRDYLVLWHGXQLW or +RZPDQ\YLVLWHGXQLWVWRDKRPHXQLW, depending on how you wish to convert the currency. Press 2. once you decide.Enter the appropriate exchange rate and press 2. (use the # key for decimals)Phone will display 5DWHVDYHG8860 UG version 0.01 3/15/99 25Features A to ZCalculating exchange ratesPress 0HQX 7Enter number of units, then press 2SWLRQVPress or to either 7RKRPH or 7RYLVLWHG, and press 2.Converted currency will displayCalendar The calendar keeps track of birthdays, meetings, simple reminders, and calls you need to make. It can even sound an alarm when it’s time for you to make a call or go to a meeting. Remember! Your phone must be switched on to use this feature. Do not switch on the phone when wireless phone use is prohibited or when it may cause interference or danger. Note: Your phone must remain on to use the calendar’s alarm feature. If your phone is off, the alarm will not sound at its scheduled time. Using the calendarPress 0HQX 8 (&DOHQGDU) If you haven’t set the time and date, your phone prompts you to set your phone’s clockWhen your phone prompts you for the time with KKPP, enter the time in hours and minutes (using two-digit fields), then press 2.Time format (24-hour or am/pm) is set using the Clock. See “Selecting time format” on page 37.When your phone prompts you for the date with PPGG\\\\, enter the month and day (using two-digit fields) and year (using a four-digit field), then press 2..$

$26Tip: Use to move the cursor right and to move it left. When you enter a digit, it writes over the number to the right of the cursor. Your phone displays the current day. You can also scroll to different days by pressing or .Once you’re at the date you want, press 2SWLRQV. Then use to highlight the option you want, and press 6HOHFW The options are:Option 1: View day With this option, you can view the notes of the day currently on display.Use to scroll through the notes. Each note allows you to choose the following 2SWLRQV: (UDVH clears the note from your calendar.(GLW gives you the same prompts you got when you made the note. 0RYH gives you the date prompt so you can move the note to another date. Option 2: Make note With this option, you’ll need to choose 5HPLQGHU, &DOO, 0HHWLQJ, or %LUWKGD\. Your phone will prompt you for more information depending on which one you choose. You can also set an alarm for any calendar note. See “Entering letters and numbers” on page 42 for help with entering information at the prompt. Note: When the alarm goes off, you can press or . Press to shut off the alarm.Option 3: Erase notes With this option, you’ll need to choose which notes to erase. If you choose all the notes for the day currently on display (2I&KRVHQ'D\), or 2QH%\2QH (for all notes in the calendar), your phone presents each note to you with the option (UDVH or %DFN.If you choose $OODW2QFH, your phone will delete all calendar notes. When prompted to confirm the erase, press <HV or 1R. 8860 UG version 0.01 3/15/99 27Features A to ZOption 4: View all This allows you to view the notes of the entire calendar. Use or to scroll through the notes. &DOHQGDUPHPRU\HPSW\ will appear if there are no notes in the calendar.Option 5: Go to date Enter the date you wish to go to. Option 6: Set the date Enter the day and month (using two-digit fields) and year (using a four-digit field), then press 2..Caller groupsYou can create groups of names in your 3KRQHERRN (see page 57), and give each group a different ringing tone. Then you’ll know when someone from that group is calling you because of the way the phone rings.Adding names to a caller groupNote: The names and numbers that you add to a group must already be stored in your phone book. See “Storing a name and number” on page 58.With the display clear, press until you see the name or number you wantPress 'HWDLOV, if shown, or skip to Step 3Press 2SWLRQVUse to reach &DOOHUJURXSV. Press 6HOHFW.Use to reach the group to which you want to add this name or number. Press 6HOHFW.Defining a ringing tone for a caller groupWith the display clear, press 1DPHV$

28Press to reach &DOOHUJURXSV. Press 6HOHFWUse to reach the group you want. Press 6HOHFWPress until you see *URXSULQJLQJWRQH. Press 6HOHFW. Use to reach the tone you want to hear when anyone from this group calls you. Press 2..Tip: You can set your phone to ring only when people from certain caller groups call you, and to otherwise be silent. See the “Caller group” description under “Ringing options” on page 64.Renaming a caller groupFollow steps 1-3 in “Defining a ringing tone for a caller group”Press until you see 5HQDPHJURXS. Press 6HOHFW.Enter the group name (see “Entering letters and numbers” on page 42 for details) and press 2.Removing names from a caller groupFollow steps 1-4 in “Adding names to a caller group”Use to reach 1RJURXS. Press 6HOHFW.Caller group graphicsWhen someone calls you from a particular caller group, your phone can display a graphic to identify which caller group that person is calling from.Press 1DPHV, scroll to &DOOHUJURXSV, then press 6HOHFWScroll to the caller group you wish to display the graphic for and press 6HOHFWScroll to *URXSJUDSKLF and press 6HOHFWScroll to 2Q to display the graphic that goes with that particular caller group Caller ID This is a network service that helps identify incoming calls. Contact your service provider for details.8860 UG version 0.01 3/15/99 29Features A to ZWhen Caller ID is active, your phone may display the caller’s phone number. The caller’s name may also display if their name and number has been stored in the phone book (see “Phone book” on page 57) or if the wireless network supports it.&DOO or &DOOFDOOHU,'XQDYDLODEOH will display when the wireless network doesn’t recognize the calling number. Also, &DOOFDOOHU,'EORFNHG may display if the calling party has blocked caller ID. Calling card If you wish to use a calling card for long distance calls, you must first store your calling card information into your phone. Your phone can store up to four calling cards.Storing your calling cardPress 0HQX 4 1 3 (6HWWLQJV - &DOOVHWWLQJV - &DOOLQJFDUG)Scroll to desired calling card and press 2SWLRQVPress or to (GLW, press 2.Enter security code and press 2.Press 6HOHFW at 'LDOLQJVHTXHQFH. Select the dialing sequence your card uses (use chart below), press or to choose sequence, then press 6HOHFWNote: The order of the following steps may vary, depending on which dialing sequence your card uses.Enter access number when prompted for the calling card’s access number (usually the 1-800 number listed on the back of the calling card), press 2.Note: You can also retrieve the access number from your phone book if it has already been stored. Simply press , then or to find the number.Enter card number and/or PIN when prompted to enter calling card number and personal identification number, then press 2.Press 2. again at 6DYHFKDQJHV?

$30Press or to &DUGQDPH and press 6HOHFW. Enter card name using your phone’s keypad, press 2..See “Entering letters and numbers” on page 42 if you need help on entering the card nameFor details about your phone’s security code, see “Security code” on page 68. *These calling cards are frequently used with these dialing sequences. However, they may vary and are subject to change at the phone company’s discretion.Choosing a calling card to usePress 0HQX 4 1 3 (6HWWLQJV - &DOOVHWWLQJV - &DOOLQJFDUG)Scroll to desired card and press 2SWLRQVPress or to highlight 6HOHFW and press 2.. Dialing Sequence Use for cards that require you to: Cards using this sequence*Access no.+ phone no.+ card no. Dial 1-800 access number, then phone number, then card number (+ PIN if required)MCI, AT&T True Choice, Sprint Canada, UnitelAccess no.+ card no.+ phone no.Dial 1-800 access number, then card number (+ PIN if required), then phone numbernetworkMCI, WorldPhone MCIPrefix + phone no.+ card no.Dial the prefix (any numbers that must precede the phone number) and phone number you want to dial, then card number, (then PIN, if required)GTE, PacBell, AT&T, Stentor8860 UG version 0.01 3/15/99 31Features A to ZEnter security code at 6HFXULW\FRGH, press 2.Your phone will display &DUGUHDG\IRUXVHMaking calling card callsEnter the phone number, including any prefix (such as 0 or 1) that your calling card may require when you make a calling card call. See your calling card for instructions.Press and hold B for a few seconds until your phone displays &DUGFDOO.Press 2. when you see :DLWIRUWRQHWKHQSUHVV2.. When you see :DLWIRUWRQHSUHVV2.DJDLQ, press 2. again.Note: This procedure may not apply to all calling card options programmed into your phone. Please look at the back of your calling card or contact your long distance company for more information.Call forwarding This network service is used to forward incoming calls to another number so you won’t miss an important call. Check with your service provider for details.Note: Before you can activate this feature, you should first store the feature code given to you by your service provider. Otherwise, this feature may not appear in the menu. However, you can use the feature code manually, if you choose, by including the feature code in front of the phone number(e.g., *72 555 1212)See “Network feature setting” on page 53 for more details.Press 0HQX 4 4 2 (6HWWLQJV - 1HWZRUNVHUYLFHV - &DOOIRUZDUGLQJ)Scroll to desired call forwarding feature (see options below) and press 6HOHFWHighlight $FWLYDWH and press 2.Enter phone number at 1XPEHU(or press 6HDUFK to locate number in phone book) and press 2.$

$32Your phone will attempt to call the network to confirm the feature code you entered in Menu 4 4 5 (see “Network feature setting” on page 53)Once the feature code had been confirmed, the feature is activatedCall forwarding options )RUZDUGDOOFDOOV forwards all incoming calls.)RUZDUGLIEXV\ forwards calls only when you’re on the phone. )RUZDUGLIQRWDQVZHUHG forwards calls if you don’t answer. )RUZDUGLIRXWRIUHDFK forwards calls if you are out of the serving wireless network. &DQFHODOOFDOOIRUZDUGLQJ cancels all call forwarding options you have active.Call log This feature automatically keeps track of numbers you’ve dialed, numbers that have called you, and the amount of time you’ve spent on calls.Using call logPress 0HQX 2 (&DOOORJ)Scroll to one of the following options, then press 6HOHFW or 2.2-10LVVHGFDOOV - See page 52.2-2'LDOHGFDOOV- See page39.2-3 5HFHLYHGFDOOV - See page62.2-4&OHDUFDOOOLVWV - See page 36. 2-5 &DOOWLPHUV- See page 34.Tip: You can dial any of the phone numbers by pressing B while the number is on the display.8860 UG version 0.01 3/15/99 33Features A to ZThe ‘Options’ soft keyWhen you access 'LDOHGFDOOV, 5HFHLYHGFDOOV, or 0LVVHGFDOOV and press 2SWLRQV, a list of options will appear on your phone’s display.&DOOWLPH shows the date and time when the call was first connected (if clock has been set)(GLWQXPEHU allows you to edit the dialed number.6DYH allows you to save the number into your phone book.(UDVH will erase the number from the call list.9LHZQXPEHU will appear only if the number has been stored in the phone book and the name is displayed instead of the number.Call restrictionsThis feature allows you to restrict incoming and outgoing calls to and from certain numbers.See “Restrict calls” on page 63 for details.Call settings This feature allows you to access and activate some of your phone’s features. Using call settingsPress 0HQX 4 1 (6HWWLQJV - &DOOVHWWLQJV)Press to reach one of the following options, then press 6HOHFW4-1-1 (PHUJHQF\NH\ - See page 41.4-1-2 $XWRPDWLFUHGLDO - See page 23.4-1-3 &DOOLQJFDUG - See page 29.$

34Call timers Your phone automatically keeps track of the amount of time you’ve spent in calls.Press 0HQX 2 5 (&DOOORJ - &DOOWLPHUV)Scroll repeatedly to access the following options /DVWFDOOdisplays call duration of last call.$OOFDOOVdisplays call duration of all calls made since timers have last been reset (see page 36 for details on how to clear call timers)./LIHWLPHU shows duration of all calls; this can not be reset (see page 48).&OHDUWLPHUV clears all call timers except the Life timer (see page 36).These call durations are for the currently-selected NAM (phone number). Your phone has separate timers for each NAM your phone uses, except for the Life timer.See “NAM selection” on page 53 for details on NAM.Note: The actual time invoiced for calls by your service provider may vary, depending upon items such as network features, rounding off for billing, and taxes.Call waiting If you have subscribed to Call Waiting, your phone will beep during a call let you know you have an incoming call. Your phone may also display the incoming caller’s identification (see “Caller ID” on page 28).Answering an incoming call with call waiting Press BSwapping between two callsPress B8860 UG version 0.01 3/15/99 35Features A to ZEnding the callsPress E to end both callsActivating call waitingYou can also activate this feature with your phone; simply ask your service provider for the feature code, store it into your phone, then activate it.Note: This feature may not appear in your phone’s menu until the feature code has been stored.See “Network feature setting” on page 53 for more details.Press 0HQX 4 4 3 (6HWWLQJV - 1HWZRUNVHUYLFHV - &DOOZDLWLQJ)Scroll to $FWLYDWH(or select &DQFHO to cancel and press 2.Your phone will attempt to call the network to confirm the feature code you entered in Menu 4 4 5 (see “Network feature setting” on page 53)Once the feature code has been confirmed, the feature is activated.Change lock code This feature allows you to change your lock code.See “Changing your lock code” on page 49.Change security code This feature allows you to change your security code.See “Changing your security code” on page 68.

$36Clear call lists This feature will clear all dialed numbers, as well as numbers of answered calls and missed calls. You can not undo this operation, so be careful. Also, see “Call log” on page 32.Press 0HQX 2 4 (&DOOORJ - &OHDUFDOOOLVWV)Highlight either $OO, 0LVVHG, 'LDOHG, or 5HFHLYHG and press 2. ($OO will clear all call lists, while the others clear their respective call lists)Clear timers This feature clears all call timers for the currently-selected NAM. See “Call timers” on page 34 for more details.Press 0HQX 2 5 4 (&DOOORJ - &DOOWLPHUV - &OHDUWLPHUV)Enter security code at 6HFXULW\FRGHand press 2.Careful: Clearing call timers can not be undone. If you are using the call timers to log or track the amount of time you are using your phone, you may wish to record the call timers before you erase them.Note: The Life timer contains important warranty information and can not be reset. See “Life timer” on page 48 for details.Clock Your phone has an internal clock that can be displayed or hidden. It also features an alarm clock (see page 21). 8860 UG version 0.01 3/15/99 37Features A to ZNote: The clock is powered by your phone’s battery. If your clock has been activated and you remove the battery while your phone is still on, you will need to reset the time after you turn your phone back on.However, if you first turn your phone off before removing the battery, your phone will retain the time and date it had before the battery was removed.Setting the clockPress 0HQX 4 2 1 (6HWWLQJV - 3KRQHVHWWLQJV - &ORFN) Scroll to $GMXVWWLPH and press 6HOHFWEnter present time at 7LPH (use two-digit fields for hours and minutes)Press 2.Select DP or SP and press 2. (if am/pm format has been selected; see below)Selecting time formatPress 0HQX 4 2 1 (6HWWLQJV - 3KRQHVHWWLQJV - &ORFN) Scroll to 7LPHIRUPDW and press 6HOHFWScroll to either KRXU or DPSPPress 2.Displaying or hiding the clockPress 0HQX 4 2 1 (6HWWLQJV - 3KRQHVHWWLQJV - &ORFN) Scroll to either +LGHFORFN or 'LVSOD\FORFN (only one will display depending on the current setting)Press 6HOHFWConference call This feature allows you to add a third party to a call. You can use this feature with local and long distance calls.$

38Note: This feature may not be available in all wireless systems. See your service provider for details and availability. Making a conference callWhile in a call, enter (or recall from the phone book) the second phone number and press BOnce the third party answers, press B to connect all three partiesPress B again if you wish to disconnect the third party. Press E to drop both parties.Recalling a number from the phone book during a conference callDuring the call, press 2SWLRQVScroll to 1DPHV and press 2.Press 6HOHFW at 6HDUFKEnter name and press 2., or just press or to scroll through the phone bookPress B Current call timer This feature displays the running elapsed time on your screen while a call is active. Once the call has ended, simply press any key to clear the display.Also, see “Call timers” on page 34.Activating the current call timerPress 0HQX 2 5 (&DOOORJ - &DOOWLPHUV) and press 'HWDLOV. With &XUUHQWFDOOWLPHU displayed, press 6HOHFW, scroll to 2Q, and press 2.8860 UG version 0.01 3/15/99 39Features A to ZCustomer care contact numberWith the press of a single button, you can quickly attempt calls to your service provider. This feature can be helpful if you’re having difficulties dialing a number, especially when traveling outside your home area. Simply press and hold the 2 key and your phone will attempt to call a customer care operator in the area. Note: This may not be available on all systems. Contact your service provider for availability.Customize profiles This feature allows you to customize individual Profiles. See “Profiles” on page 61 for details.Dialed calls Your phone automatically stores the last 10 numbers you’ve dialed. Press 0HQX 2 2 (&DOOORJ - 'LDOHGFDOOV) Press or to scroll through dialed numbers listPress B to dial the number you wish to callYou can also access the last 10 dialed numbers if you press B, then quickly press or to scroll through the list.Also, see “Call log” on page 32 for details on other call lists.The ‘Options’ soft keySee “The ‘Options’ soft key” on page 33.

$40Earpiece volume The scroll keys on your phone will adjust the earpiece volume during a phone call. The top scroll key increases while the bottom one decreases the volume.If an accessory like a headset or a car kit, or one with its own loudspeaker, is connected to your phone, the scroll keys will adjust the volume for that accessory. Note: Using the scroll keys to adjust earpiece volume functions only during phone calls.Emergency calls Before attempting any emergency calls, see “Emergency Calls” on page 94 for important safety information.If the phone is not on, switch it onKey in the emergency number for your present location (e.g. 911 or other official emergency number). Emergency numbers vary by location. Press BIMPORTANT!This phone, like any cellular phone, operates using radio signals, cellular and landline networks, as well as user-programmed functions which can not guarantee connection in all conditions. Therefore, you should never rely solely upon any cellular phone for essential communications (e.g., medical emergencies). Remember, to make or receive any calls, the phone must be switched on and in a service area with adequate cellular signal strength.Emergency calls may not be possible on all cellular phone networks or when certain network services and/or phone features are in use. Check with local cellular service providers.8860 UG version 0.01 3/15/99 41Features A to ZIf certain features are in use (keyguard, restrict calls, etc.), you may first need to turn those features off before you can make an emergency call. Consult this document and your local cellular service provider. When making an emergency call, remember to give all the necessary information as accurately as possible. Remember that your cellular phone may be the only means of communication at the scene of an accident - do not cut off the call until given permission to do so. Emergency key 9 With this feature on, the phone attempts to make an emergency call when you press 9, then B. The phone dials the emergency number pre-programmed into your phone.Note: You can also dial an emergency call by pressing and holding 9 until the phone indicates it is attempting to make an emergency call. However, this method does not work when Keyguard is active or when the phone is connected to a modem.Activating Emergency key 9 Press 0HQX 4 1 1 (6HWWLQJV - &DOOVHWWLQJV - (PHUJHQF\NH\), scroll to 2Q to activate or 2II to cancel, then press 2..IMPORTANT!Official emergency numbers vary by location (e.g. 911). Only one emergency number is programmed into your phone to be dialed automatically by Emergency key 9, which may not be the proper number in all circumstances.$

42Entering letters and numbersYou can enter letters, as well as numbers, when storing information into your phone by using your phone’s keypad. When you see the letter you wish to enter, simply press the key associated with that letter until it appears on the display (numbers also appear). ABC modeWhen you need to enter letters into your phone, it will automatically switch over to mode. Your phone displays the icon to indicate that your phone is in ABC mode. It also displays when you are viewing names rather than numbers.When is displayed, you can enter these characters:While you’re editing a name, the key will move the cursor to the left, and will move it to the right. Press &OHDU to correct any mistakes.If you wish to enter an empty space between characters, press 0 for each space.Key Characters Key Characters1 .,’?!-1 7 PQRS72 ABC2 8 TUV83 DEF3 9 WXYZ94 GHI4 0 Enters an empty space, 05 JKL5 * (See below for details)6 MNO6 # Changes letter case; long press toggles between ABC/abc and 123 mode8860 UG version 0.01 3/15/99 43Features A to ZChanging letter casePress the # key to switch between upper and lower case letters. The icon will switch to to indicate you are using lower case.123 modeWhen storing names to the phone book, you can enter a number within a name at any time. Simply press that particular number key a few times until it appears. However, you can do this more quickly by accessing the mode, without having to scroll through each letter to access the number you wish to enter.Simply press the # key for about 2 seconds while in mode and the icon will appear. While in this mode, only numbers can be entered. Letters can not be entered unless your phone is in mode.Press the # key again for a couple of seconds if you wish to deactivate the mode.Special characters (for storing names)When in ABC mode (see page 21), you can press the ∗ key and the following special characters will appear. You can use these characters to help when storing names in your phone book. Simply press or to highlight the one you wish to use and press ,QVHUW.. , ? ! : ; - + # * ( ) ‘ “ _ @ & $ £ % / < > ¿ ¡ § = [ ] ¥TIP: If you wish to access a special character that appears toward the end of this list, press for quicker access.Special Characters (for storing numbers)The following special characters are helpful when you store names to your phone book (see page 57). Simply press the * key once or repeatedly, and the following characters can be stored within the number sequence. (S) creates a pause when a number is dialed; the digits located to the right of the “S” are automatically sent as touch tones after a 2.5 second pause (see page 76).

44(Z) creates a “wait” when a number is dialed. The “Z” makes your phone wait for you to press 6HQGor B, then it sends the digits located to the right of the “w” as touch tones (see page 76).You can add as many special characters as you need in a single number sequence. These characters can not be entered while in mode.Erasing stored names and numbersSee “Erasing stored names and numbers” on page 58.Erasing your entire phone bookSee “Erasing your entire phone book” on page 59.GamesYou have four exciting games to choose from in your phone. Press 0HQX 6 to choose one of the following games:REMEMBER! Your phone must be switched on to use this function. Do not switch on the phone when wireless phone use is prohibited or when it may cause interference or danger.MemoryReveal pictures to find pairs in as few tries as possible. Move the cursor with the 2 (up), 4 (left), 6 (right), and 8 (down) keys. Press the 5 key to reveal pictures. Press the # key to jump right over revealed pictures or move from top left to bottom right. Press the ∗ key to jump left over revealed pictures or move from bottom right to top left. Once found, pairs stay visible.8860 UG version 0.01 3/15/99 45Features A to ZSnakeFeed the snake with as many goodies as possible and watch it grow. Use keys 2, 4, 6, and 8 to turn the snake toward food. The longer the snake’s tail grows, the higher the score. If the snake hits its own tail or the surrounding wall, the game is over.LogicFind a secret combination of figures. Available figures are shown at the top of the display before you accept the first guess row. Use the 2, 4 and 8 keys to move the cursor and the 5 key to select the figure. To copy a figure from a previously accepted guess row, start scrolling with the 4 key, move the cursor to the desired figure in the normal way and accept the selection with the 5 key.Once you think you have the right combination, press the * key. The result is presented as a set of marks over the row. A correct figure in the right place gives a full mark; a correct figure in the wrong place gives a half mark. The game ends when all the figures are correct and in the right place.RotationNo information available at this time.Game optionsWhen you select a game, you can choose from the following submenus:/HYHO allows you to choose the level of difficulty.1HZJDPH starts a new game.7RSVFRUH will display the top score (does not appear in Logic).,QVWUXFWLRQV will describe how the game is played.Note: or may appear in the options list if a game is interrupted, not finished, or if you have lost the game.

$46Inbox When you receive a text message, it’s stored in the Inbox. Your phone will display 0HVVDJHUHFHLYHG, along with the text message icon, and makes a sound (depending on the message alert tone; see page 51). Please see “Text messages and pages” on page 71 for complete details on this feature. In-call menuWhile in a call, you may notice the 2SWLRQV soft key. Pressing this will access you to the in-call menu, and you may notice the following choices:0XWH Allows you to mute the microphone; if your microphone is already muted, this will change to (QGPXWH (see “Microphone” on page 52)7RXFKWRQHV You can manually enter a touch tone string or search for one in your phone book (see “Phone book” on page 57)1HZFDOO You can make a third party conference call (see “Conference call” on page 37)0HQX Allows you access to your phone’s menu1DPHV Allows you access to your phone book (see “Phone book” on page 57)Keyguard This feature helps protect the keypad against accidental keypresses. See “Keyguard” on page 13 for complete details.8860 UG version 0.01 3/15/99 47Features A to ZKeypad tones This is one of the settings in your phone’s Profiles (see page 61). It sets the volume of the tone you hear when you press your phone’s keys. Note that if you choose the 6LOHQW profile, keypad tones will be turned off.Setting the keypad tones Press 0HQX3 (3URILOHV) Your phone lists each profile. Use to highlight the one you want to set the keypad tones for and press 2SWLRQV. Highlight &XVWRPL]H and press 2.. Press to .H\SDGWRQHV and press 6HOHFW Press to scroll through the options; your phone plays a sample of each. Press 2. for the one you want.Language Because many wireless phone customers speak English as a second language, your phone allows you to choose your phone’s displayed language. Choosing a language for your phonePress 0HQX 4 2 5 (6HWWLQJV - 3KRQHVHWWLQJV - /DQJXDJH), scroll to the language you wish to use and press 2..You can choose from English, French, Spanish, Portuguese, Russian, Hebrew, and Chinese Traditional.Last call timer This feature displays the duration of your last call.$

$48See “Call timers” on page 34.Last number redial When you want to call your last dialed number,Press B and wait 3 secondsNote: You must be at the start screen before you press BLetter caseYou can change from upper to lower case when entering letters into your phone.See “Changing letter case” on page 43 for complete details.Life timer The life timer displays the total time of all calls dialed and received with your phone (in hours and minutes only). The life timer can not be reset and is used in conjunction with your phone’s warrantyAlso, see “Call timers” on page 34.Lights This is one of the settings in your phone’s &DU Profile (see page 61). This feature determines whether the lights are on only when you use your phone, or if they are on at all times. This setting works only when your phone is connected to a car kit. Press 0HQX 3 (3URILOHV)8860 UG version 0.01 3/15/99 49Features A to ZYour phone lists each profile. Use to highlight &DU and press 2SWLRQV. Note: will not appear in the list until the phone has been connected to a car kit at least once time.Highlight &XVWRPL]H and press 2.. Press to highlight /LJKWV and press 6HOHFW. Use to scroll through your choices and press 2.If you select $XWRPDWLF, your phone’s lights are turned off within fifteen seconds if no keys are pressed. If 2Q is selected, then the lights will remain on the entire time your phone is connected to the car kit.Listen to voice messages This feature allows you to access your voice messages.See “Voice messages” on page 79 for complete details.Lock code You’ll need the lock code to activate and deactivate Phone Lock (see page 59), or to change your lock code. The default lock code is 1234. If you enter an incorrect lock code five times in a row, your phone will prompt you for the security code (see page 68). Changing your lock codeIn a lock code, only numeric characters are accepted.Enter 0HQX 4 3 2 3 (6HWWLQJV - 6HFXULW\VHWWLQJV - $FFHVVFRGHV - &KDQJHORFNFRGH)Enter lock code at (QWHUORFNFRGHand press 2.Enter new lock code, press 2.Verify new lock code, press 2.$

$50Note: When you change your lock code, make sure you store it in a safe place, away from your phone. Avoid entering access codes similar to emergency numbers to prevent accidental emergency calls.Manual touch tones This setting determines how long touch tones are produced as you press the keys on the keypad. Note that touch tones are sometimes called DTMF tones.See “Touch tones” on page 76 for details. Setting manual touch tonesPress 0HQX 4 2 3 1 (6HWWLQJV - 3KRQHVHWWLQJV - 7RXFKWRQHV - 0DQXDOWRXFKWRQHV) and highlight one of the following options, then press 2.&RQWLQXRXV means the tone sounds for as long as you press and hold the key. )L[HGsets the tone length to .1 second, regardless of how long you press the key. 2II turns the tones off, and no tones will be sent when you press the keys. Memory statusThis feature allows you to see how many free and in-use memory locations are in your directory. Also, see “Phone book” on page 57.Press 1DPHV, scroll to 2SWLRQV and press 6HOHFW. Then scroll to 0HPRU\VWDWXV and press 6HOHFW again8860 UG version 0.01 3/15/99 51Features A to ZMessages This feature allows you to access your voice and text messages, as well as composing your own welcome note.Using messagesPress 0HQX 1 (0HVVDJHV)Scroll to one of the following options, then press 6HOHFW1-1 7H[WPHVVDJHV - See page 71.1-2 9RLFHPHVVDJHV - See page 79.1-3 :HOFRPHQRWH - See page 81.Message alert tone This is one of the settings in your phone’s Profiles (see page 61). It sets the tone that your phone makes when you get a text message. Also, see “Text messages and pages” on page 71. Press 0HQX 3 (3URILOHV) Your phone lists each profile. Use to highlight the one you want to set the message alert tone for and press 2SWLRQV. Highlight &XVWRPL]H and press 2.. Press to highlight 0HVVDJHDOHUWWRQH, then press 6HOHFW. Use to scroll through your choices (your phone plays samples) and press 2..$

52Microphone You can mute and unmute your phone’s microphone while a call is in progress. During a call, your phone’s softkeys change from 1DPHV and 0HQX to 2SWLRQV and 0XWH.Muting and unmuting your phone You can mute the phone’s microphone during a call; simply press 0XWH. To unmute the microphone, press 8QPXWH. If these texts are not available, press 2SWLRQV, scroll to 0XWH or (QGPXWH and press 6HOHFW.Muting and unmuting also affect the microphones of any accessories connected to the phone.Missed callsYour phone will keep track of the last 10 calls you have missed if you weren’t around to answer the call. Missed calls will appear in your phone only if it was turned on and in a service area when the call was missed.If the display says ‘Missed calls’Press /LVW. To call back the displayed number, press B. Press ([LW to go back to the start screen.The ‘Options’ soft keySee “The ‘Options’ soft key” on page 33.Checking the missed calls list anytimePress 0HQX 2 1 (&DOOORJ - 0LVVHGFDOOV), then scroll through the list.This shows you the phone numbers of the 10 most recent calls you’ve not answered. 8860 UG version 0.01 3/15/99 53Features A to ZWhen the )RUZDUGLIQRWDQVZHUHG option in the Call Forwarding feature (see page 31) is selected, your phone treats the forwarded calls as missed calls.Also, see “Call log” on page 32 for details on other call lists.NAM selection The service provider programs your phone with the phone number and system information into your phone’s memory when your phone is first activated. This is called a Number Assignment Module (NAM). For example, your phone can be activated in up to 3 different service areas (e.g. one in Dallas, another in Chicago, and maybe one more in New York), each giving your phone a different phone number or account.Only one number can be active at a time. When you select a phone number, you’re also selecting which system you’re using as your home system (see “System” on page 70). The first phone number displayed with this menu is the currently selected number.Note: It may not be necessary to have three NAMs for your phone if your service provider has service or roaming agreements for each area in which you wish to use your phone. Contact your service provider for details.Selecting the NAM for your phonePress 0HQX 4 4 6 (6HWWLQJV - 1HWZRUNVHUYLFHV - 1$0VHOHFWLRQ), highlight the phone number you want to use and press 2..Note: You need at least one active number to make calls. You can not change from one NAM to another during a call.Network feature setting Call forwarding (page 31), Call waiting (page 34) and Send own number (page 69) are network services available through your service provider or dealer.

$54When you subscribe to any of these services, your service provider or dealer gives you a separate feature code to activate each service. Deactivation codes are used to deactivate each service. Once you store the appropriate code in your phone, the service appears as a menu item. You can then use the menu to activate and deactivate these services. Each time you use a feature that requires a feature code, that code is sent to the network to verify you’re using the correct feature code.Note: If your phone has more than one phone number programmed, any feature codes stored will apply only to your primary phone number, or NAM 1.See “NAM selection” on page 53 for details on NAM.Storing codesPress 0HQX 4 4 5 (6HWWLQJV - 1HWZRUNVHUYLFHV - 1HWZRUNIHDWXUHVHWWLQJ)At )HDWXUH&RGH, enter the feature code or deactivation code received from your dealer (e.g. ∗74, ∗740, etc.), press 2. to the service that the code applies to and press 6HOHFW to suboption, then 6HOHFW (Repeat step as required, based on number of suboptions)(Use step four only for call forwarding options) to $FWLYDWH or &DQFHO, then press 2.Network services Some of the features in this menu are network services that require a subscription. See your service provider for details and availability. 4-4-1 9RLFHSULYDF\ - See page 80.4-4-2 &DOOIRUZDUGLQJ - See page 31.4-4-3 &DOOZDLWLQJ - See page 34.8860 UG version 0.01 3/15/99 55Features A to Z4-4-4 6HQGRZQQXPEHU - See page 69.4-4-5 1HWZRUNIHDWXUHVHWWLQJ - See page 53.4-4-6 1$0VHOHFWLRQ - See page 53.These features will not appear in the menu unless they are activated using . See “Network feature setting” on page 53 for details.One-touch dialing This feature allows you to make phone calls quickly and easily with the touch of a button.You must store names and numbers in your phone book (see page 58) before you can use this feature. Then you can assign a name from the phone book to a one-touch dial location using your phone’s keys 2 through 8.Note: Keys 1 and 9 are used exclusively for dialing your voice mailbox (see page 79) and for attempting emergency calls (see page 94) to the emergency number programmed into your phone (e.g. 911 or other official emergency number). The 2 key is for dialing a customer care operator (see page 39), which can be overwritten if you prefer.Assigning one-touch dial locationsPress 1DPHV scroll to WRXFKGLDOLQJ and press 6HOHFWScroll to next available empty location, HPSW\will appear, then press $VVLJQScroll to select desired name and press 6HOHFWRepeat as necessaryCalling a number using one-touch dialingNote: The 2 key is for dialing a customer care operator, which can be overwritten if you prefer.Press and hold the key (2 through 8) for a few seconds to call the number in the corresponding one-touch dial location.$

56Note: If you press and hold 1, your phone calls your voice mailbox. If you press and hold 9, and Emergency key 9 (Menu 4 1) is , your phone attempts a call to the emergency number programmed into your phone (e.g. 911 or other official emergency number).Changing numbers in one-touch dial listWith this feature, you can assign a different number to any one-touch dial location.Press 1DPHV scroll to WRXFKGLDOLQJ and press 6HOHFWScroll to the location you wish to change and press 2SWLRQVScroll to &KDQJH, then press 6HOHFWScroll through phone book to select new number and press 6HOHFWErasing one-touch dial locationsPress 1DPHV scroll to WRXFKGLDOLQJ and press 6HOHFWScroll to the location you wish to erase and press 2SWLRQVScroll to (UDVH, press 6HOHFW, then press 2. at (UDVH"OutboxThis is where all outgoing text messages are stored.See “Text messages and pages” on page 71 for more details.Paging You can receive pages with your phone.See “Text messages and pages” on page 71.8860 UG version 0.01 3/15/99 57Features A to ZPhone bookYou can store up to 250 numbers and associated names in your phone’s memory. These numbers are right at your fingertips for easy dialing.Things to know about the phone bookStored numbers may be up to 32 digits long. Stored names may be up to 16 characters long.You can not store identical names into your phone (i.e., John, John); make sure that like names are somewhat different in the phone book (i.e., John, Johnny). 5HSODFH" followed by the currently stored name displays when storing a name already in memory.Accessing the phone bookPress 1DPHV, scroll to desired submenu and press 6HOHFW.About the submenusThe phone book has several submenus from which you can choose.6HDUFK allows you to search for a specific name.$GGQHZ allows you to enter new names and numbers.2SWLRQV lets you choose your scrolling view, as well as to show memory status.WRXFKGLDOLQJ allows you to assign up to seven one-touch dial locations (see page 54 for details). &DOOHUJURXSV allows you to rename or change the ringing tone for a caller group (see“Caller groups” on page 27).(UDVHDOO lets you erase every name and number in your phone book. You can erase one name and number at a time by pressing 'HWDLOV, then 2SWLRQV when viewing a name already in the directory.

$58Storing a name and numberPress 1DPHVScroll to $GGQHZ and press 6HOHFWEnter name using the keypad (use # to switch between upper and lower case) and press 2.Enter phone number and press 2.Also, see “Entering letters and numbers” on page 42 and “Quick save” on page 70.Changing a number stored with a nameRecall stored name, then press 'HWDLOVto view numberPress 2SWLRQV, scroll to (GLW and press 6HOHFWPress 2. while name is displayed, unless you wish to change it. If so, press and hold &OHDU, re-enter name and press 2.Press and hold &OHDU to erase number or use the and keys to editEnter new numberPress 2. to save new numberRecalling names & numbersAt the start screen, press or to view names in directory. Then scroll to the person you wish to call and press B to dial the number (phone will display number dialed to confirm).Recalling numbers by nameAt the start screen, press 1DPHV. Then press the number on the keypad with the corresponding first letter of the name you wish to call.You can also recall numbers by name by pressing 1DPHV, then press 6HOHFW at 6HDUFK. Enter the name of the person you wish to recall and press 2..Erasing stored names and numbersRecall stored name8860 UG version 0.01 3/15/99 59Features A to ZPress 'HWDLOVPress 2SWLRQVHighlight (UDVH, then press 6HOHFW, then 2.Note: You can not undo Erase functions, so be careful!Erasing your entire phone bookPress 1DPHVScroll to (UDVHDOOand press 6HOHFWPress 2. at $UH\RXVXUH"Enter security code at 6HFXULW\FRGHand press 2.Warning: This feature will erase your entire phone book, which can not be undone!Phone lock When you turn this on, your phone will lock after you switch your phone off and back on. Then, each time you turn your phone on, it will prompt you for a lock code when you press either 1DPHV or 0HQX. When the phone lock is on, you can not access most of your phone’s memory and menu features, or make phone calls without entering the lock code.Turning on phone lockPress 0HQX 4 3 2 1 (6HWWLQJV - 6HFXULW\VHWWLQJV - $FFHVVFRGHV - 3KRQHORFN). Enter the lock code then press 2.. Then scroll to 2Q, and press 2. again.When your phone is locked, calls may be possible to the emergency number programmed into your phone (e.g. 911 or other official emergency number) including calls with Emergency key 9 (page 41).You can also store a number in the 8QORFNHGSKRQHQXPEHUORFDWLRQ, which allows you to call this number even though your phone is locked. (See page 78 for details).$

$60Answering a call with phone lock onPress any key except E and P Turning off phone lockPress 0HQX 4 3 2 1 (6HWWLQJV - 6HFXULW\VHWWLQJV - $FFHVVFRGHV - 3KRQHORFN). Enter lock code and press 2.. Then scroll to 2II and press 2. again.With phone lock off, you can now use your phone without entering the lock code each time you turn your phone on.Phone settings Phone settings allow you access to other phone features such as an alarm clock and your phone’s language.Using phone settingsPress 0HQX 4 2 (6HWWLQJV - 3KRQHVHWWLQJV), then scroll to one of the following options, then press 6HOHFW:4-2-1 &ORFN - See page 36.4-2-2 $ODUPFORFN - See page 21.4-2-3 7RXFKWRQHV - See page 76.4-2-4 5HVWRUHIDFWRU\VHWWLQJV - See page 62.4-2-5 /DQJXDJH - See page 47.4-2-6 6OLGHVHWWLQJ - See page 70.8860 UG version 0.01 3/15/99 61Features A to ZProfiles Now you can adjust and customize your phone to whatever environments you find yourself in (i.e. meetings, a movie, etc.). With Profiles, you can control your phone’s ringing volume, ringing tone, message alert, keypad tones, warning tones, etc., in a matter of seconds.Note: Restore factory settings (see page 62) will reset any changes made in Profiles back to the factory defaults. The default setting is .Accessing Profiles Press 0HQX 3Selecting different ProfilesIf you want to change your phone’s Profile, quickly press the P key. Quickly press P again to scroll through each choice, then press and hold the P key for a second to select that Profile. You can also scroll through the list of Profiles with a quick press of the P key. Then press or to choose another Profile and press 2.. Either way, this only allows you to select other Profiles; you can not customize them here. Keep reading to learn how to customize a Profile.Customizing ProfilesPress 0HQX 3 (3URILOHV) and scroll to desired Profile, then press 2SWLRQV.Once 2SWLRQV is selected, 6HOHFW, &XVWRPL]H and 5HQDPH will appear as your choices. Once you have selected one of these items, press 2.. If you wish to go back to the main menu, press %DFN.6HOHFW activates the currently highlighted Profile.&XVWRPL]H allows you to customize a Profile by changing the current settings.5HQDPH allows you to rename the Profile.$

$62When you select &XVWRPL]H, press 2. and you’ll have access to several lists and sub-menus that will enable you to adjust the settings on the current Profile.Note: and will not appear in the Profiles list unless your phone is connected to a car kit or a headset. However, they will remain in the menu once connected for the first time.Note: When you change a setting in the current Profile, it only affects that Profile and will not change your phone’s normal settings.Renaming profilesPress 0HQX 3 (3URILOHV)Scroll to desired Profile and press 2SWLRQVScroll to 5HQDPH and press 2.Enter new name and press 2. againNote: Some profiles can not be renamed.Received calls This shows you the phone numbers of the 10 most recent calls you’ve answered.Press 0HQX2 3 (&DOOORJ - 5HFHLYHGFDOOV), then scroll through the numbers.Also, see “Call log” on page 32 for details on other call lists.The ‘Options’ soft keySee “The ‘Options’ soft key” on page 33.Restore factory settings You can reset the settings of many of your phone’s features to factory defaults (as in a new telephone).8860 UG version 0.01 3/15/99 63Features A to ZRestoring factory settingsPress 0HQX 4 2 4 (6HWWLQJV - 3KRQHVHWWLQJV - 5HVWRUHIDFWRU\VHWWLQJV), enter security code and press 2..Note: The memory, timers, language selection, security code and lock codes are not reset. However, any Profiles you have modified will reset when you restore your settings.Renaming profiles See “Profiles” on page 61.Restrict calls This feature allows you to restrict incoming and outgoing calls. Outgoing calls are restricted from a list of restrictions that you create yourself.Restrict outgoing callsIf no restrictions have been defined in your phone, you will notice only one option: allows you to create your own list of outgoing call restrictions. The maximum number of call restriction groups you can define is 10.Once you have entered and have added at least one restriction, the following options will be added: allows you to select call restrictions from the outgoing calls list. allows you to edit an existing outgoing call restriction. will erase any existing outgoing call restrictions.Note: When calls are restricted, calls may be possible to the emergency number programmed into your phone (e.g. 911 or other official emergency numbers). However, Emergency key 9 may not operate depending on the type of restriction you choose.$

$66Ringing volume This is one of the settings in your phone’s Profiles (see page 61). It sets the default ringing volume for incoming voice calls and message alert tones. Setting the ringing volume Press 0HQX 3 (3URILOHV) Your phone lists each profile. Use to highlight the one you want to set the ringing volume for and press 2SWLRQV. Highlight &XVWRPL]H and press 2.. Press to 5LQJLQJYROXPH, then press 6HOHFW. Scroll through the options. When you hear the volume level you wish to use, press 2..Note: The ringing volume setting is stored individually for the handsfree car kit and the headset.Roaming This is a term used to indicate that your phone is not in its home area. Calls made or received while roaming are usually more expensive than calls made in your home area.When roaming in some systems outside your home area, your phone may not be recognized by the host system (the one you’re travelling in) and you may not be able to place a call. Contact your service provider for more specific information on how roaming works with your phone, as well as any information on coverage limitations.8860 UG version 0.01 3/15/99 67Features A to ZRoaming Indicators When your phone begins roaming, it will beep once and display 52$0 or (;7(1'('$5($, depending on how roaming works with your phone. Contact your service provider for more details. If your phone is not roaming (i.e. in its home area) it will either display +20( or the name of the service provider.Saved This is where saved text messages are stored. See “Text messages and pages” on page 71 for details.Scrolling viewThere are three different options on how you can view the phone book. Your choices are:1DPHOLVW shows all stored names in a scrolling list. Three names will appear at any given time. To view other names in the directory, scroll back and forth through the list using or . 1DPHOLVW is the default setting.1DPHQXPEHU displays individual names and numbers stored in your directory. Only one name will display on your screen at a time, with the corresponding phone number. Use or to view other names.1DPHRQO\ shows individual names only. To view other names, use or . You can view the corresponding phone number by pressing 'HWDLOV, then or .Selecting your scrolling viewPress 1DPHVScroll to 2SWLRQV,then press 6HOHFWPress 6HOHFW at 6FUROOLQJYLHZPress or to select either 1DPHOLVW, 1DPHQXPEHU, or 1DPHRQO\, then press 2.$

$68Security settingsThis menu includes the following security features:4-3-1 5HVWULFWFDOOV - See page 63.4-3-2 $FFHVVFRGHV - See page 21.The $FFHVVFRGHV submenu includes 3KRQHORFN (page 59), 8QORFNHGSKRQHQXPEHU (page 77), &KDQJHORFNFRGH (page 49), and &KDQJHVHFXULW\FRGH (page 68).Security code Your phone will prompt you for a security code for certain features. These features can be used only after the correct security code has been successfully entered.Note: When entering your security code, ***** will appear on the display to keep others from viewing your code.If you make a mistake entering the code, erase the last digit entered by pressing &OHDU, or press and hold &OHDU. Then enter the correct code or press %DFN to exit the current feature.If you enter an incorrect security code (&RGHHUURU will appear) five times in a row, your phone won’t accept any entries for the next five minutes.Your phone’s default security code is 12345. It’s highly recommended that you change this code at once, write it down, and store it in a safe place away from your phone.Changing your security codePress 0HQX 4 3 2 4 (6HWWLQJV - 6HFXULW\VHWWLQJV - $FFHVVFRGHV - &KDQJHVHFXULW\FRGH)Enter security code and press 2.Enter new security code at (QWHUQHZVHFXULW\FRGH, press 2.8860 UG version 0.01 3/15/99 69Features A to ZEnter new security code again at 9HULI\QHZVHFXULW\FRGH, press 2.Phone will display 6HFXULW\FRGHFKDQJHGNote: If you have changed your security code and don’t remember the new code, contact your service provider. Once you have changed your security code, the default setting is no longer valid.Send own number In most service areas, when you call someone your name will be presented to his/her caller ID (if they subscribe). This feature allows you to block their caller ID (i.e. your number will not be presented) when you call them. This feature works on a per-call basis. Contact your service provider for more details. Note: Before you can deactivate this feature, you must first store the feature code given to you by your service provider. Otherwise, this feature may not appear in the menu. See “Network feature setting” on page 53 for more details.Note: This feature is only effective when calling to a number that is equipped with Caller ID. Press 0HQX 4 4 4 (6HWWLQJV - 1HWZRUNVHUYLFHV - 6HQGRZQQXPEHU) to <HV (to show your number) or 1R (to not show it) and press 2.Enter the number you wish to call (or press 6HDUFK to retrieve the number from the phone book and press 2.), then press 2.Your phone will attempt to call this number with the feature code you stored in Menu 4 4 5 (see “Network feature setting” on page 53)SettingsThis main menu allows you access to other features. See these individual entries for more information.$

$704-1 &DOOVHWWLQJV - See page 33.4-2 3KRQHVHWWLQJV - See page 60.4-3 6HFXULW\VHWWLQJV - See page 68.4-4 1HWZRUNVHUYLFHV - See page54.Slide settingThis feature allows you to answer and end calls simply by opening and closing the slide.See “Using the slide” on page 11 for more details.Storing a name & numberYou can save names and numbers in the Phone book. Either use the method described in “Storing a name and number” on page 58 or the “quick save” method described below.Quick saveEnter the phone number and press 6DYH. Enter a name at 1DPH if you wish (optional), then press 2..Also, see “Entering letters and numbers” on page 42.System Your phone is capable of working in Residential, Private, and Public Systems (such as your Home System). You can choose how your phone selects a network to use. 8860 UG version 0.01 3/15/99 71Features A to ZThis feature is 0HQX 5 in your phone. The default is $XWRPDWLF, which means your phone automatically searches for networks available to you and chooses the appropriate one. Every time you switch on your phone, it resets this to $XWRPDWLF.If you choose 0DQXDO, your phone searches for networks, then begins displaying them. Your phone displays $9$,/$%/( or 127$9$,/$%/( for the systems it finds (You can not use 127$9$,/$%/( systems). Use the key to scroll through the choices, and press 2. when you see the one you want. If you choose 1HZ6HDUFK, your phone begins a new search for new Private and Residential systems. When it finds the best new system, it displays it. You can then 6HOHFW it, or start another search by pressing 1H[W.Note: If you have two phone numbers (two NAMs), the and features are only used with your primary phone number (NAM 1). See “NAM selection” on page 53 for more information concerning NAMs.To switch from private to publicIf you are in a private system and want access to a public system, press and hold 0HQX when you are not in a call. Your phone will display 6HDUFKSXEOLFV\VWHPV", press 2. and your phone will use the public system for the next (only once) outgoing call. After that it goes back to $XWRPDWLFsystem selection.Text messages and pages Before you can send or receive text messages and pages, you must subscribe to the text messaging network service. Some or all of these features may not be available in some wireless systems. Please see your service provider for details and availability.Note: Text messages that you receive with your phone may appear different at times, due to messages that originate in networks other than your own.$

$72Also, the maximum length of a text message may depend on the network’s capabilities.Text message optionsWhen you access 7H[WPHVVDJHV, you will view a screen with five different options. is where incoming messages are received and stored. All new, unread messages are kept here. is where all saved, read messages are kept here. allows you to write text messages, text pages, and e-mail messages. is where outgoing messages are stored.(UDVHDOO allows you to erase all text messages. However, unread text messages will not be erased.Writing text messagesNote: Writing and sending text messages may not be available in all wireless systems. Please contact your service provider for details.You can write a text message and send it as an e-mail, page, or fax with your phone. The maximum length of any short message is up to 225 characters. The maximum length of an e-mail address is 70 characters.Sending text messagesPress 0HQX 1 1Scroll to :ULWHQHZ and press 6HOHFWWrite your message using the keypad and press 2SWLRQVTo send the text message, press 2. with 6HQG highlightedEnter the phone number (or press 6HDUFK to locate in the phone book), then press 6HQG8860 UG version 0.01 3/15/99 73Features A to ZSending optionsIf you press 2SWLRQV when sending a text message, you’ll find the following choices:6HQG sends the message as a normal text message.6HWWLQJV allows you to tag your messages (see below)6HQGDV allows your to send your message as an (PDLO, 3DJH, or )D[.6DYH will save your message to the 6DYHG folder.&OHDUVFUHHQ will clear the message screen.Message settings8UJHQW will notify recipient that your message is important.5HDGUHFHLSW notifies you that recipient has opened your message.5HSO\UHT will request a reply from your recipient.&DOOEDFNQR will place your phone number within the message.Sending messages as e-mail, faxes, and pagesYou can send your text message to an e-mail address, a fax machine, or a pager.Press 0HQX 1 1, then scroll to :ULWHQHZ and press 6HOHFWWrite your message using the keypad and press 2SWLRQVScroll to 6HQGDVand press 2.Choose either (PDLO, 3DJH, or )D[ and press 2.Enter e-mail address, fax number, or pager number and press 6HQGReceiving text messagesThe maximum length of a received text message is up to 225 characters. Your phone has space for up to 30 text messages, depending on the length of each message.$

$74When you receive a text messageText messages are shown in the order that they were received, in their order of priority.0HVVDJHUHFHLYHG indicates an unread message or page. If more than one message is received, the number of received messages will be listed first.1HZHPHUJHQF\PHVVDJH indicates that the message or page received was sent by someone via the service provider. Emergency messages are sent only in situations where life and/or property are in immediate danger. Emergency messages are listed first and will override all other messages.8UJHQW messages are also high priority messages.Reading text messagesWith 0HVVDJHUHFHLYHG displayed, press 5HDG and scroll to new message, then press 5HDGagainReading optionsPress 2SWLRQV while a text message is displayed to access the following reading options:5HDGQH[Wallows you to read the next message.(UDVH will erase the message.6DYH will save the message to the 6DYHG folder.&DOOEDFN will automatically call whoever sent the message if any phone numbers are included within the message.)RUZDUG allows you to forward the message to someone else.5HSO\ allows you to reply to the received message.Calling someone back in a messagePress B while the message is displayed to dial the number quickly. Or, with the message and the phone number displayed on your phone’s screen, you can press 2SWLRQV, scroll and select &DOOEDFN, then press 2..8860 UG version 0.01 3/15/99 75Features A to ZNote: If more than one number is on the display, the numbers are displayed in a list. Simply select the phone number you want to call and press B. If no numbers are found, your phone will display 1RQXPEHUIRXQGRQWKLVVFUHHQ.Forwarding a messageNote: This feature is only available if your phone has been activated in a wireless system that supports the sending of text messages.With the message displayed, press 2SWLRQV, scroll to )RUZDUG and press 2.. Then send the message as you normally would.Replying to a messageNote: This feature is only available if your phone has been activated in a wireless system that supports the sending of text messages.With the message displayed, press 2SWLRQV, scroll to 5HSO\ and press 2.. Then write your reply and send the message as you normally would.If a phone number appears in the message you received, it’s used as the default for the reply you’re sending. This can be replaced by another number, if you wish.Receiving a page Your phone will display0HVVDJHUHFHLYHG. The message will display &DOO, followed by the name or number of the person who paged you. Names will appear only if that person has been stored in the phone book.When your phone’s memory is full One or more messages, of lowest priority, will automatically be deleted in order to receive new text messages when your phone’s memory is full. If the message memory is still full, your phone will display 1RVSDFHPHVVDJHZDLWLQJ. You can clear this notification by pressing 2..Note: Messages are usually deleted from your . An incoming emergency message may delete messages from your folder.$

76Touch tones Your phone can generate various sounds, called touch tones, when the keys are pressed. These are also known as DTMF tones.Touch tones can be used for many automated, over-the-phone services such as checking bank balances, airline arrival and departure times, and using voice mailbox options. Touch tones can be sent only when a call is active. Storing touch tone stringsTouch tone strings can be used for sending and receiving information with your phone. For example, you can store your office voice mailbox number, along with your password for easy access to your messages. Store touch tone strings the same way you store phone numbers (see page 58).You can store a whole digit sequence in your phone book and send it as touch tones for frequently-used strings of numbers.Sending a touch tone stringMake sure Menu 4 2 3 1 (6HWWLQJV - 3KRQHVHWWLQJV - 7RXFKWRQHV - 0DQXDOWRXFKWRQHV) is not set to 2II. During a call, press 2SWLRQVScroll to 7RXFKWRQHV and press 2.Enter touch tone string or recall string from the phone book and press 2. Note: Use caution when sending confidential information over the air when using DTMF tones in analog mode.Storing touch tone strings with phone numbersEnter the phone number (e.g. your office voice mailbox)Press ∗∗∗ (p) or ∗∗∗∗ (w) Enter the touch tone string (e.g. voice mailbox password)Store the number as you normally would8860 UG version 0.01 3/15/99 77Features A to ZNote: See “Special Characters (for storing numbers)” on page 43 for details on “p” and “w” characters.When you dial this number, your phone first dials the phone number, then waits (because of the “w” character) for you to press 6HQG. Your phone then sends your password.If you include a “p” character instead of a “w”, your phone pauses for 2.5 seconds, then automatically sends your password as touch tones. Linking phone numbers with touch tone stringsThis feature allows you to store a phone number in one phone book location and link it to another phone book location that contains a touch tone string.First, you must first store the touch tone string into a phone book location and then assign it a one-touch dialing location (see “One-touch dialing” on page 55).Enter the phone number you wish to link with the touch tone stringPress * twice (you should have a “+” character next to the phone number)Enter the one-touch dialing location where the touch tone string is stored (i.e. if the string is stored in location 2, then enter 2)Press 6DYH and then enter the name that corresponds with the phone number (this is optional)Press 2.When you wish to call this number, make the call as you normally would. Then, when you wish to send the touch tone string, simply press 2..Touch tone length This feature determines the length of each touch tone when they are sent automatically.6KRUW sets the tone length to .1 second. /RQJ sets the tone length to .5 second.

$78You can set the touch tone length by pressing 0HQX 4 2 3 2 (6HWWLQJV - 3KRQHVHWWLQJV - 7RXFKWRQHV - 7RXFKWRQHOHQJWK).Unlocked phone number When the phone lock is on (see page 59), no calls can be made. However, you can store one number into your phone that can be called when it’s locked. Storing the unlocked phone numberPress 0HQX4 3 2 2 (6HWWLQJV - 6HFXULW\VHWWLQJV - $FFHVVFRGHV - 8QORFNHGSKRQHQXPEHU)Enter lock code and press 2.Enter phone number at 1XPEHU(or press 6HDUFK and scroll through the phone book)Press 2.Calling the unlocked phone numberNote: Your phone must be locked to use this feature.Press or once, then B or you can manually enter the phone number as it is stored and press B.Vibrating alert This is one of the settings in your phone’s Profiles (see page 61). When your phone has the vibrating battery attached, you can set your phone to vibrate when you receive a voice call. Note: This setting will not appear in your phone unless a vibrating battery has been attached.Activating vibrating alertPress 0HQX 3 (3URILOHV) 8860 UG version 0.01 3/15/99 79Features A to ZYour phone lists each Profile. Use to highlight the one you want to set the vibrating alert for and press 2SWLRQV. Highlight &XVWRPL]H and press 2.. Press to reach 9LEUDWLQJDOHUW, then press 6HOHFW again. Use to highlight 2Q or 2II and press 2.. If you choose 2Q, your phone will vibrate even if you have set 5LQJLQJRSWLRQV (see page 64) to 6LOHQW."The vibrating battery does not vibrate when the phone is connected to or placed in any charging device." Voice mailbox number This number dials your voice mailbox. See “Voice messages” in next section.Voice messages Voice mail is a network service that may require a subscription from your service provider.Your phone will notify you when you receive a voice message. 1HZYRLFHPHVVDJH will appear on the display along with the icon, and you’ll hear a short beep. Your phone will display the number of voice messages if you’ve received more than one.Setting up your voice mailboxBefore you can retrieve any voice messages, you need to store your voice mailbox number. Your service provider usually gives this number to you.$

$80When you’re ready to store your voice mailbox number, press 0HQX 1 2 2 (0HVVDJHV9RLFHPHVVDJHV9RLFHPDLOER[QXPEHU). Then enter your voice mailbox phone number and press 2.. This number can be up to 32 digits long and is used until it’s changed. So if your phone number changes, you may need to change your voice mailbox number along with it.Greetings, passwords, and promptsThese may vary in different wireless systems. So if you need information about how to record your greeting or how to store your password, contact your service provider. You’ll also need to contact them on how to listen to voice messages once you’re connected to your voice mailbox.Listening to your voice messagesIf 1HZYRLFHPHVVDJH is displayed, just press /LVWHQ and follow the prompts. If you’d rather listen to your messages later, press ([LW.You can listen to messages anytime if you press and hold the 1 key; &DOOLQJYRLFHPDLOER[ will appear on the display. Or if you prefer, you can access your voice mailbox by pressing 0HQX 1 2 1 (0HVVDJHV9RLFHPHVVDJHV/LVWHQWRYRLFHPHVVDJHV).Voice privacy Note: This feature may not be available in all areas. Please see your service provider for details and availability.Used only in digital networks, voice privacy encrypts the voice channel so that people can not eavesdrop on your conversation.Voice privacy will become active only during a call and will notify you with a beep. 9RLFHSULYDF\ active will also appear on the display.If you turn this feature on and voice privacy becomes inactive for any reason, your phone displays 9RLFHSULYDF\QRWDFWLYH and beeps.You may set this to 2Q or 2II by pressing 0HQX 4 4 1 (6HWWLQJV - 1HWZRUNVHUYLFHV - 9RLFHSULYDF\).8860 UG version 0.01 3/15/99 81Features A to ZVolumeYou can adjust the ringing volume and earpiece volume with your phone. See “Earpiece volume” on page 40 and “Ringing volume” on page 66.Warning tones This is one of the settings in your phone’s Profiles (see page 61). Warning tones include tones your phone makes for conditions such as errors, confirmations, power on, battery low, and recharge battery. You can set warning tones on or off. Turning warning tones on and off Press 0HQX 3 (3URILOHV) Your phone lists each Profile. Use to highlight the one you want to set the warning tones for and press 2SWLRQV. Highlight &XVWRPL]H and press 2.. Press to :DUQLQJWRQHV, then press 6HOHFW. Scroll to 2Qor 2II and press 2. Welcome note You can program a welcome note into your phone to display a message when you first turn it on (i.e. hello, your name, a reminder, etc.). The maximum length is 36 characters.Press 0HQX 1 3 (0HVVDJHV - :HOFRPHQRWH)Enter new message or edit an existing one, then press 2SWLRQVPress to 6DYH or (UDVHand press 2.$

Microsoft NSW-6NX Dual Band Tri Mode Non-Broadcast Cellular Transcei User Manual manual

Microsoft Mobile Oy Dual Band Tri Mode Non-Broadcast Cellular Transcei manual

manual

Navigation menu

Namespaces

Views

Navigation