Microsensys PENSOLIDHFX RFID Pen Style Read/Write Unit PENsolid HF User Manual

Microsensys GmbH RFID Pen Style Read/Write Unit PENsolid HF

User Manual

iID®PENsolid HF User Manual UserMan-iID PENsolid HF-007E.docx   © 2016 microsensys  QuickStartGuide   RFID Read/Write Device for mobile scan applications iID®  PENsolid  is  a  mobile  RFID  device  suitable  as  Bluetooth™  enabled  RFID  read/write  unit  for  HF  (13.56MHz) frequency applications.  Based on it’s PEN style form and the implemented touch tip it can be used as input device for tablets and smartphones with touch and capacitive screens. iID® PENsolid can be configured in Bluetooth™ HID mode. In this operation mode it emulates a Bluetooth™ keyboard.  Depending on operation mode, iID® PENsolid works together with Windows, Android and iOS devices. Product Short Description & available Versions:  iID PENsolid                       System:  iID-3000 RFID Pen Style Read/Write HF Unit v1.00 with RTC, MEM, BT, USB, Li accu Display: LEDs for power, BT, status           Buttons: SCAN, ON/OFF System:  iID3000, ISO 15693, 14443, all customized  Antenna: K3            Operation Mode: DOC / SPC       Bluetooth: SPP / HID Case Format:   120x26x20 mm³, Li Ion Battery 450mAh Product Code: 73.72.750.xx  An additional product version of  iID® PENsolid is available for UHF (868 / 915 MHz) RFID applications. Please contact microsensys for further information.
iID®PENsolid HF User Manual UserMan-iID PENsolid HF-007E.docx   © 2016 microsensys  QuickStartGuide FCC compliance statement  IC compliance statement   These devices comply with part 15 of the FCC Rules. Operation is subject to the following two conditions:  1. These devices may not cause harmful interferences; 2. These devices must accept any interference received, including interference that may cause undesired operation.  The following figures list the Grant by FCC ID Number for each of the following devices:  FCC ID:   ZLCPENSOLIDHFX  Please refer to the FCC’s website ( http://www.fcc.gov/ ) to view the grant and related documentation.  CAUTION ! Exposure  to  Radio  Frequency Radiation.  The  radiated  output  of  this  device is far below  the  FCC  radio frequency exposure limits. Nevertheless, the device shall be used in such a manner that the potential for human contact during normal operation is minimized. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8inches) during normal operation. These devices may not be co-located with any other transmitter or transmitter antenna.  NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide  reasonable  protection  against  harmful interferences when the equipment is operated in a  commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,  may  cause  harmful  interference  to  radio  communications.  Operation  of  this  equipment  in  a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes or modifications not expressly approved by Microsensys GmbH could void the user’s authority to operate  the  equipment  described  in  the  manual.  This  device  contains  Bluetooth™  module  FCC  ID: QOQWT12.  Industry Canada ID:  21228-PENSOLIDHFX, contains Bluetooth™ module IC ID: 5123A-BGTWT12A  This device complies with Industry Canada RSS-210. Operation is subject to the following two conditions:  (1) this device may not cause interference, and  (2) this device must accept any interference, including interference that may cause undesired operation of the device.   Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio RSS-210. L’exploitation est autorisée aux deux conditions suivantes :  (1) l’appareil ne doit pas produire de brouillage, et  (2)  l’utilisateur  de  l’appareil  doit  accepter  tout  brouillage  radioélectrique  subi,  même  si  le  brouillage  est susceptible d’en compromettre le fonctionnement.
iID®PENsolid HF User Manual UserMan-iID PENsolid HF-007E.docx   © 2016 microsensys  QuickStartGuide Performance description iID® PENsolid is suitable for mobile data capture and wireless RFID read / write applications, which can be connected via its integrated USB interface to PCs. The BluetoothTM-Interface is suitable to connect to smart phones, tablet computers or laptops.  Based on iID® SPC functionality, scripts can be used for definition of LED, buzzer and button support as well as communication functionalities as RF, USB and Bluetooth™.  iID® PENsolid is a battery powered device, which can be recharged using the micro USB interface. Battery cycles may vary from some hours to several days depending on the device configuration. When the device is connected via it’s USB interface, the device is powered by USB power.  The device is available in several types supporting HF as well as UHF systems suitable for closed coupling communication with very small sized up to large RFID transponders. Additionally all devices support TELID® sensor transponder applications.  First commissioning                         Before using your device the first time, please charge the internal rechargeable battery using included micro USB cable.   (1) ON/OFF button (3)  rechargeable  battery  state LED (orange) (4) Bluetooth™ state LED (blue) (2)  SCAN-button (5)(6)  Green  and  red operation state LED Focused  RFID antenna,  main  RF field direction Micro-USB connector  Hole for hand strap, clip Touch tip
iID®PENsolid HF User Manual UserMan-iID PENsolid HF-007E.docx   © 2016 microsensys  QuickStartGuide  Manner of functioning iID® PENsolid may be used as RFID read/write device with USB- or Bluetooth™ interface or RFID scanner using the integrated scan button. See following table for available configurations, for further information see iID® SPC/MPC related documents.  Functionality Operation mode configuration Interface Remark Read/write interface DOC USB Bi-directional  USB  communication, based  on  iID®  driver  engine,  device configuration Bluetooth™ HID (human interface  device / key-board mode) SPC Bluetooth™ HID Uni-directional communication, script with output functionality on device   iID® PENsolid is delivered in SPC/HID mode. Please adjust operation mode connecting to a PC via USB interface. Using iID® interface configuration tool you may configure the device according your requirements before first usage. Microsensys provides sample scripts for device usage in SPC mode, which are available for download in iID® interface configuration tool.   iID® PENsolid buttons support following functionalities: Button Functionality (1) ON/OFF  Power on device, power off device when pressed for 3 seconds (2) SCAN button  Perform scan (while device in SPC mode) (1) and (2) Keep holding (1) and (2) while device is off until lights come  up  will  switch  on  device  and  perform Bluetooth™ reset.
iID®PENsolid HF User Manual UserMan-iID PENsolid HF-007E.docx   © 2016 microsensys  QuickStartGuide  Software to be installed Please download and install iID® software package including iID® DEMOsoft 2013, iID® interface config tool and iID® connection tool as well as iID® driver engine from:  http://download.microsensys.de/CDContent/Install/Setup%20iID%c2%ae%20software%20package.exe.   Device configuration is possible using iID® interface configuration tool running on Windows PC environment - via BT connection as well as USB interface. For using USB interface you may also need to install the USB driver, which is available at  http://download.microsensys.de/CDContent/USBDriver/Microsensys%20USB%20devices%20driver%20CDM%20v2.10.00%20WHQL%20Certified.zip  Depending on operation mode (see “manner of functioning”) and platform installation of further software may be required: Operation mode Platform Software DOC  Windows  32/64 (without RT) iID® software package including iID® driver engine, optional iID® tray application (http://download.microsensys.de/CDContent/Install/iID%c2%ae%20tray%20application.zip) Windows  Mobile, Windows embedded handheld iID® driver engine, iID® DEMOsoft (http://download.microsensys.de/CDContent/Install/RFIDDriver/Windows/iID3000PRO/, http://download.microsensys.de/CDContent/Install/iID%c2%ae%20DEMOsoft/Windows/Mobile/RFID-Demo%20iID%20driver%20engine.CAB) , optional iID® trigger scan  (http://download.microsensys.de/CDContent/Install/iID%c2%ae%20tray%20application/iID%c2%ae%20TriggerScan%20Mobile/iID%20TriggerScan.CAB) Android iID® Android DEMOsoft  (http://download.microsensys.de/CDContent/Install/iID%c2%ae%20DEMOsoft/Android/) SPC (Bluetooth™ HID) All  platforms (Windows,  Android, iOS) No further software required  Further microsensys product related software is located here: http://download.microsensys.de/CDContent/.
iID®PENsolid HF User Manual UserMan-iID PENsolid HF-007E.docx   © 2016 microsensys  QuickStartGuide  Signs & their meaning iID®  PENsolid  LEDs  are  used  to  show  operation  state.  Additionally  there  are  device  states  shown  as described below.  Symbol Description    (3=ORANGE) OFF = battery good, BLINK = low charge, ON = USB charging (4=BLUE) BLINK = Bluetooth™ connection not established, ON = Bluetooth™ connection established (5)  operation  state  LED (GREEN) In  DOC  mode  automatic  RF  state  visualization,  in  SPC  mode  free programmable (6)  operation  state  LED (RED) In  DOC  mode  automatic  RF  state  visualization,  in  SPC  mode  free programmable (5) & (6) Blinking while POWER_ON or POWER_OFF   Safety instructions   The device may only be used for the intended purpose designed by for the manufacturer.    Unauthorized changes and the use of spare parts and additional devices which have not been sold or recommended by the manufacturer may cause fire, electric shocks or injuries. Such unauthorized measures shall exclude any liability by the manufacturer.    The liability-prescriptions of the manufacturer in the issue valid at the time of purchase are valid for the device. The manufacturer shall not be held legally responsible for inaccuracies, errors, or omissions in the manual or automatically set parameters for a device or for an incorrect application of a device.    Repairs may only be executed by the manufacturer.    Installation, operation, and maintenance procedures should only be carried out by qualified personnel.    Use of the device and its installation must be in accordance with national legal requirements and local electrical codes.    When working on devices the valid safety regulations must be observed.
iID®PENsolid HF User Manual UserMan-iID PENsolid HF-007E.docx   © 2016 microsensys  QuickStartGuide  Technical data Following table contains general technical data.   Parameter Description   Housing  Material Plastic case Dimension 117mm x 27mm x 19(23)mm  2 buttons Power supply  USB (power supply) micro USB female, 5V +/- 5%, ripple <50mV Battery Lithium polymer battery, 3.7V, 420mAh   Current consumption  Sleep mode typ. 5μA Idle mode typ. 30mA Active mode typ. 200mA   RFID Interface  Carrier frequency 13.56MHz +/- 7kHz Implemented standards ISO14443, ISO15693 RF output power 200 mW Antenna K3 Operating distance 0mm .. 50mm (depending on transponder type and environmental conditions)   Additional interfaces  Bluetooth interface Bluetooth™ 2.0 USB interface USB 2.0   Operation modes  DOC Direct online communication, serial communication or iID®  driver engine or iID® Android driver engine SPC Script programmed communication, HID communication or serial communication or iID® driver engine or iID® Android driver engine
iID®PENsolid HF User Manual UserMan-iID PENsolid HF-007E.docx   © 2016 microsensys  QuickStartGuide  Equipment delivered: 1 x iID®PENsolid   Including following Accessories: 1 x Hand strap 1 x USB cable 1 x CD-ROM (Software & Documents) Standard accessories: USB cable Hand strap    Complementary microsensys Documents Technical Datasheets:      PENsolid-HF xxx.pdf, PENsolid-UHF xxx.pdf Product or System Documentation:  DOC-iID SPC 01D.pdf, Quick-iID MPC 01D.pdf            Contact/Copyright Micro-Sensys GmbH • In der Hochstedter Ecke 2 • 99098 Erfurt • Germany phone:  +49 (0) 3 61 5 98 74-0     fax:  +49 (0) 3 61 5 98 74-17 e-mail:  info@microsensys.de     web:  www.microsensys.de  Any reproduction of this short manual in whole or in part, the storage in electronic media and the translation into foreign languages without the written permission of microsensys GmbH is forbidden.  © 2016 microsensys • all rights reserved

Navigation menu