Microhard Systems 12XN58-26 HIGH POWER N MINIPCI 5.8GHz User Manual XN58 26 120323

Microhard Systems Inc HIGH POWER N MINIPCI 5.8GHz XN58 26 120323

Users Manual

2 x 2 802.11N MIMO mini-PCI Modules High Power N MiniPCI 5.8GHz XN58-26 5GHz Single-Band 802.11n MIMO 2 x 2 miniPCI Features • Atheros XSPAN family chipset • IEEE 802.11n compliant and backward compatible with 802.11a • Enhanced sensitivity • Optimized isolation path • Superior thermal performance • Maximum output power 26dBm@802.11a / 28dBm MIMO aggregate • Built-in ESD Protection with ESD/EMP Immunity Threshold: 15KeV ① • Multi-Country Roaming Supported (IEEE802.11d Global Harmonization Standard) • 2 x MMCX connectors allowing for improved mechanical stability and low loss
XN58-26 MIMO MINIPCI CARD RADIO TX SPECIFICATIONS DataRate TX Power (per chain)TX Power (2 chains)Tolerance 6-24Mbps 26dBm 28dBm ±2dB 36Mbps 25dBm 28dBm ±2dB 48Mbps 24dBm 27dBm ±2dB 802.11a 54Mbps 23dBm 26dBm ±2dB DataRate TX Power (per chain) TX Power(2 chains) Tolerance DataRate TX Power (per chain) TX Power(2 chains) ToleranceMCS 0/8 25dBm 28dBm ±2dB MCS 0/8 24dBm 27dBm ±2dB MCS 1/9 25dBm 28dBm ±2dB MCS 1/9 24dBm 27dBm ±2dB MCS 2/10 23.5dBm 26.5dBm ±2dB MCS 2/10 22.5dBm 25.5dBm ±2dB MCS 3/11 23.5dBm 26.5dBm ±2dB MCS 3/11 22.5dBm 25.5dBm ±2dB MCS 4/12 22.5dBm 25.5dBm ±2dB MCS 4/12 22dBm 25dBm ±2dB MCS 5/13 22dBm 25dBm ±2dB MCS 5/13 20.5dBm 23.5dBm ±2dB MCS 6/14 21dBm 24dBm ±2dB MCS 6/14 20.5dBm 23.5dBm ±2dB 5GHz 11n HT 20 MCS 7/15 20dBm 23dBm ±2dB 5GHz 11nHT 40MCS 7/15 17dBm 20dBm ±2dB RX SPECIFICATIONS DataRate Sensitivity (2 chains) Tolerance DataRate Sensitivity (2 chains) Tolerance 6M -96dBm ±2dB 24M -89dBm ±2dB 9M -96dBm ±2dB 36M -86dBm ±2dB 12M -95dBm ±2dB 48M -82dBm ±2dB 802.11a 18M -93dBm ±2dB 802.11a54M -79dBm ±2dB MCS0 -95dBm ±2dB MCS0 -92dBm ±2dB MCS1 -93dBm ±2dB MCS1 -90dBm ±2dB MCS2 -90dBm ±2dB MCS2 -87dBm ±2dB MCS3 -89dBm ±2dB MCS3 -84dBm ±2dB MCS4 -85dBm ±2dB MCS4 -81dBm ±2dB MCS5 -81dBm ±2dB MCS5 -77dBm ±2dB MCS6 -79dBm ±2dB MCS6 -76dBm ±2dB 5GHz 11n HT 20 MCS7 -75dBm ±2dB 5GHz11n HT 40MCS7 -74dBm ±2dB Technical Specifications Chipset Atheros AR9220 Host Interface 32-bit mini-PCI Type IIIA+ (6.55mm longer than IIIA type) Operating Voltage 3.3 VDC 11a Cont. Tx @6M 4.9W 11na Cont. Tx@HT20 MCS0 4.3W 11na Cont. Tx@HT40 MCS0 4.8W 11a Cont. Rx 2.5W Power Consumption Standby 0.8W Antenna Connector 2 x MMCX connector IEEE 802.11a : 54Mbps 48Mbps 36Mbps 24Mbps 18Mbps 12Mbps 9Mbps 6Mbps 1Nss: 65Mbps @ 800GI, 72.2Mbps @ 400GI (Max.) 20MHz 2Nss: 130Mbps @ 800GI, 144.4Mbps @ 400GI (Max.) 1Nss: 135Mbps @ 800GI, 150Mbps @ 400GI (Max.) Data Rate IEEE 802.11n : 40MHz 2Nss: 270Mbps @ 800GI, 300Mbps @ 400GI (Max.) 5.725 ~ 5.850 GHz (US & Canada) 5.725 ~ 5.875 GHz (Europe) Frequency Range IEEE 802.11a/n: Modulation Techniques OFDM: BPSK, QPSK, 16-QAM, 64-QAM RoHS Compliance Yes Temperature Range Operating: -20ºC to 70ºC Storage: -40ºC to 90ºC Humidity Operating:5% to 95% (non-condensing) Storage: Max.90% (non-condensing) Dimension 59.6mm x 57.5mm x 7.5mm
ESD CABLE SPECIFICATION Cable Dimensions 26cm length Terminal Material Copper Attachment Procedure End of ESD Cable tied to Earth Ground Ordering Information② CODES Connectors type Carton Dimension XN58-26 MMCX For 50pcs (pcs/ctn), 0.40m * 0.22m * 0.085m / 0.006 = 1.5KG For 250pc (pcs/ctn), 0.45m * 0.45m * 0.24m / 0.006 = 8.1KG c Module grounding cable included d Configurations are subject to change without notice Please contact Compex sales representatives for other available configurations
COMPLIANCE INFORMATION This device complies with the following radio frequency and safety standards. Important to OEM Manufacturer: This following FCC Warning must be included in the HOST User Manual. FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. Note 1: This module certified that complies with RF exposure requirment under mobile or fixed condition, this module is to be installed only in mobile or fixed applications. A mobile device is defined as a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitter's radiating structure(s) and the body of the user or nearby persons. Transmitting devices designed to be used by consumers or workers that can be easily re-located, such as wireless devices associated with a personal computer, are considered to be mobile devices if they meet the 20 centimeter separation requirement.
A fixed device is defined as a device is physically secured at one location and is not able to be easily moved to another location. Note 2: Any modifications made to the module will void the Grant of Certification, this module is limited to OEM installation only and must not be sold to end-users, end-user has no manual instructions to remove or install the device, only software or operating procedure shall be placed in the end-user operating manual of final products. Note 3: The device must not transmit simultaneously with any other antenna or transmitter. Note 4: To ensure compliance with all non-transmitter functions the host manufacturer is responsible for ensuring compliance with the module(s) installed and fully operational. For example, if a host was previously authorized as an unintentional radiator under the Declaration of Conformity procedure without a transmitter certified module and a module is added, the host manufacturer is responsible for ensuring that the after the module is installed and operational the host continues to be compliant with the Part 15B unintentional radiator requirements. Since this may depend on the details of how the module is integrated with the host, Microhard System Inc. shall provide guidance to the host manufacturer for compliance with the Part 15B requirements. Note 5: FCC ID label on the final system must be labeled with “Contains FCC ID: NS912XN58-26” or “Contains transmitter module FCC ID: NS912XN58-26”. The transmitter module must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the host product. Microhard Systems Inc. is responsible for the compliance of the module in all final hosts.
IMPORTANT NOTE REGARDING ANTENNA USE Antenna Use (Point to Multipoint) 2x2 Operation Chain1 Chain2
Dimensions Drawing Microhard Systems Inc Address: 150 Country Hills Landing NW Calgary Alberta Canada Contact Name: Hany Shenouda Tel. No: 403-248-0028 Fax No: 403-248-2762 Email: shenouda@microhardcorp.com For more information, visit www.compex.com.sg

Navigation menu