Meru Networks AP300 MULTI RADIO 802.11a/b/g/n WIRELESS LAN ACCESS POINT User Manual AP300

Meru Networks Inc. MULTI RADIO 802.11a/b/g/n WIRELESS LAN ACCESS POINT AP300

Users Manual

Meru AP300Installation GuideSeptember 14, 2007Copyright © Meru Networks, Inc., 2003–2007. All rights reserved.Other names and brands may be claimed as the property of others.
Contents 1 Controlled Use Only—Beta DraftContentsAbout This Guide . . . . . . . . . . . . . . . . . . . . . . . 3Audience . . . . . . . . . . . . . . . . . . . . . . . . . 3Other Sources of Information . . . . . . . . . . . . . . . . . . 3Meru Publications . . . . . . . . . . . . . . . . . . . . . 3External References . . . . . . . . . . . . . . . . . . . . 4Guide to Typographic Conventions . . . . . . . . . . . . . . . . 4Syntax Notation. . . . . . . . . . . . . . . . . . . . . . . 5Contacting Meru . . . . . . . . . . . . . . . . . . . . . . 6Customer Services and Support . . . . . . . . . . . . . . . . 6AP300 Series Introduction . . . . . . . . . . . . . . . . . . 1Hardware Specification . . . . . . . . . . . . . . . . . . . 2AP300 Product Overview . . . . . . . . . . . . . . . . . . 2Installing the AP300 . . . . . . . . . . . . . . . . . . . . . 3Safety Precautions . . . . . . . . . . . . . . . . . . . . . . 3Unpack the AP300 . . . . . . . . . . . . . . . . . . . . . . 4Determine Power Requirements . . . . . . . . . . . . . . . . . 5Installation Requirements . . . . . . . . . . . . . . . . . . . 5Additional Equipment . . . . . . . . . . . . . . . . . . . 7Install the Access Points . . . . . . . . . . . . . . . . . . . . 7Select a Location . . . . . . . . . . . . . . . . . . . . . 7Attach the AP300 Antennas . . . . . . . . . . . . . . . . . 8Attach Standard Antennas . . . . . . . . . . . . . . . . . 8Attach Remote Antennas . . . . . . . . . . . . . . . . . 9Mount the Access Point . . . . . . . . . . . . . . . . . . . 9Mount AP300 Horizontally . . . . . . . . . . . . . . . . . 9Mount AP300 on a Wall . . . . . . . . . . . . . . . . . . 10Check AP300 LED Activity . . . . . . . . . . . . . . . . . . . 11Configure AP300 Software . . . . . . . . . . . . . . . . . . . 12Configure AP300 Using the CLI . . . . . . . . . . . . . . . 12Configure AP300 Using the GUI . . . . . . . . . . . . . . . 14Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . 17AP300 Brackets. . . . . . . . . . . . . . . . . . . . . . . 19Specifications . . . . . . . . . . . . . . . . . . . . . . . 21Wireless Interface for All APs . . . . . . . . . . . . . . . . . . 21Ethernet Interface for All Meru APs . . . . . . . . . . . . . . . . 22
2Meru System Director Getting Started Guide Controlled Use Only—Beta DraftPhysical Description for All Meru APs . . . . . . . . . . . . . . . 22Regulatory Information . . . . . . . . . . . . . . . . . . .23USA . . . . . . . . . . . . . . . . . . . . . . . . . . 23Underwriters Laboratories . . . . . . . . . . . . . . . . . 23Notices . . . . . . . . . . . . . . . . . . . . . . . 23FCC Radiation Exposure Statement . . . . . . . . . . . . . . 24Radio Frequency Interference Requirements . . . . . . . . . . . 24Interference Statement . . . . . . . . . . . . . . . . . 24Channels . . . . . . . . . . . . . . . . . . . . . . . . . . 27IEEE 802.11a . . . . . . . . . . . . . . . . . . . . . . 27IEEE 802.11b/g . . . . . . . . . . . . . . . . . . . . . 28IEEE 802.11n . . . . . . . . . . . . . . . . . . . . . . 30
© 2007 Meru Networks, Inc. About This Guide 3 About This GuidezThis guide describes the various options for configuring the Meru AP300 and the wireless LAN. The architecture and fundamental operations of system are described.AudienceThis guide is intended for network administrators configuring and maintaining the Meru AP300. Familiarity with the following concepts is helpful when configuring the Meru Wireless LAN System:zNetwork administration, including:—Internet Protocol (IP) addressing and routing—Dynamic Host Configuration Protocol (DHCP)—Configuring Layer 2 and Layer 3 switches (if required by your switch)zIEEE 802.11n (Wi-Fi) concepts, including:—ESSIDs—WEPzNetwork Security (optional)—WPA—802.1X—RADIUS—X.509 certificatesOther Sources of InformationAdditional information is available in the following Meru publications, Web site, and external references.Meru PublicationszMeru AP300 Install GuidezMeru System Director Release Notes
4Meru System Director Configuration Guide © 2007 Meru Networks, Inc.Guide to Typographic Conventions zMeru Access Point and Radio Switch Installation GuidezMeru Controller Installation GuidezMeru System Director Command ReferencezMeru System Director Getting Started GuideExternal ReferenceszStevens, W. R. 1994. TCP/IP Illustrated, Volume 1, The Protocols. Addison-Wesley, Reading, Mass.zGast, M.S. 2002. 802.11 Wireless Networks, The Definitive Guide. O’Reilly and Associates, Sebastopol, Calif.Guide to Typographic ConventionsThis guide uses the following typographic conventions in paragraph text to help you identify information: Bold text Identifies commands and keywords in syntax descriptions that are entered literally.Italic text Used for new terms, emphasis, and book titles; also identifies arguments for which you supply values in syntax descriptions.Courier font Identifies file names, folder names, computer screen output, and text in syntax descriptions that you are required to type. Ctrl-Denotes that the Ctrl key should be used in conjunction with another key, for example, Ctrl-D means hold down the Ctrl and press the D key. Keys are shown in capitals, but are not case sensitive.Note:Provides extra information, tips, and hints regarding the topicCaution!Identifies important information about actions that could result in damage to or loss of data, or could cause the application to behave in unexpected waysWarning! Identifies critical information about actions that could result in equipment failure or bodily harm
Syntax Notation © 2007 Meru Networks, Inc. About This Guide 5 Syntax NotationIn example command syntax descriptions and examples, the following text elements and punc-tuation are used to denote user input and computer output for the command. In general, Courier font is used for command input and output at the command line; bold indicates required text and italics indicates values that are to be replaced. The following figure shows a sample of syntax notation.bold Required command, keywords, and punctuation.italic Arguments or file names where you substitute a value.no The optional no form of the command disables the feature or function. [ ] Optional elements are enclosed by square brackets.{ } Braces indicates that one of the enclosed elements must be used.|Choices among elements are separated by vertical bars.[{}] A required choice within an optional element.…The preceding argument can be repeated. [no] action target {keyword|keyword}Command or action. In some cases, action takes you to another command mode.One or more repeated values[argument ...]Choose between the enclosed elements The optional no form disables the command; without the no, enables or re-enables.Keyword or command within a submode.Note:Many commands have a default setting or value, listed in the Default section of the command page.
6Meru System Director Configuration Guide © 2007 Meru Networks, Inc.Contacting Meru Contacting Meru You can visit Meru Networks on the Internet at this URL:http://www.merunetworks.comClick Support to view Meru Customer Services and Support information.Customer Services and SupportFor assistance, contact Meru Customer Services and Support 24 hours a day at +1-888-637-8952 (+1-888-Meru-WLA(N)) or +1-408-215-5305. Email can be sent to support@merunetworks.com.Meru Customer Services and Support provide end users and channel partners with the following:zTelephone technical supportzSoftware update supportzSpare parts and repair service
© 2007 Meru Networks, Inc. AP300 Series Introduction 1 Chapter 1AP300 Series IntroductionThe Meru AP300 Access Point delivers high performance, full-speed, draft 2.0 compatible 802.11n connectivity while simultaneously supporting legacy 802.11a/b/g devices. The Meru Networks family of AP300 Access Points is supported by System Director Release 3.4.SR3 and later. Figure 1: AP300Key product features include: z802.11n support with channel bonding in both 2.4GHz and 5GHz frequency bands. Channel bonding combines two 20Mhz channels into a single-wide 40Mhz channel for increased theoretical throughput.zDual-band external antenna options optimized for MIMO modezPlug and Play deployment using centralized Meru Controller platformszMulti-layered security including standard WPA2, 802.11i security such as automatic traffic inspectionThis access point is available in three different configurations:zAP320: Two 802.11n radios with 3x3 MIMO mode streamszAP310: Single 802.11n radio with 3x3 MIMO mode streamzAP311: Single 802.11n radio with 3x3 MIMO mode stream and single 802.11a/b/g radio (upgradeable)A2A2ALANRF1RF2200207
2Meru Access Point and Radio Switch Installation Guide © 2007 Meru Networks, Inc. Each of these Access points may be powered by a standard 802.3af for 2x2 MIMO Mode. For 3x3 full channel mode, use either a power supply or a a 802.3at PoE device. Hardware SpecificationThe AP300 hardware platform features:z10/100/1000 Ethernet port, copperz1 serial/console port (reserved)zDC power input (5 Volts)z6 RPSMA external antenna connectorsFigure 2: AP300AP300 Product OverviewThe Meru AP300 Series, supported by System Director release 3.4.SR3 and later, includes the following features:zAir Traffic Control technology for 802.11n devices and legacy a/b/g devices z3x3 MIMO (Multiple Input, Multiple Output) technology with three dedicated, configurable input/output streams that deliver data rates up to 300 MbpszSoftware upgradeable radios for maximum investment protectionzMeru channel span architecture which requires no channel planning or configurationzSix standard multiband, omni-directional antennas for AP320 and AP311. Three standard multiband, omni-directional antennas for AP310.zPowered by 5 volt DC input, 802.11af compliant PoE device, or 802.11at compliant PoE device.A5A65V DCCON LAN00209Ethernet Portserialport power antenna (5 of 6)antenna (6 of 6) lock reset
Safety Precautions © 2007 Meru Networks, Inc. Installing the AP300 3 Chapter 2Installing the AP300This chapter describes how to physically install the Meru AP300. It contains the following sections:zSafety PrecautionszUnpack the AP300zDetermine Power RequirementszInstallation RequirementszInstall the Access PointszConfigure AP300 SoftwarezCheck AP300 LED ActivityzConfigure AP300 SoftwarezTroubleshootingSafety PrecautionsIMPORTANT—Read and follow the regulatory instructions in Appendix C before installing and operating this product.This product is intended to be supplied by a UL Listed power supply, marked Class 2 or LPS, and rated minimum 5 Vdc, 3A.Caution!The AP300 is not certified for plenum installations, and should not be installed in the plenum space.Document Number: 3.5.1 Rev 1
Determine Power Requirements © 2007 Meru Networks, Inc. Installing the AP300 5 Determine Power RequirementsYour power requirements will vary, depending on which AP300 radios are deployed and what mode is used. See Table 2. Table 2: AP300 Power OptionsInstallation RequirementsThe AP300 standard mounting bracket can be removed. The AP300 is also designed to be used with brackets supplied by other vendors; if you use a bracket other than an AP150 bracket (which is identical), you need to obtain three shoulder screws (see Appendix A). Meru APs can be mounted on Cisco 1230 series brackets, but the Cisco 1240 and 1250 series brackets are new and not compatible with the Meru bracket. The AP300 has a security cable slot so you can lock the AP300 with a standard security cable, such as those used to secure laptop computers. See Figure 3.AP300 Configuration Power Options1 radio – b/g mode Either a power supply (included) or PoE 802.3af1 radio – n-mode Either a power supply (included) or PoE 802.3af2 radios – 1 b/g-mode, 1 n modeFor 2x2 MIMO mode, use either a power supply (included) or PoE 802.3af.For 3x3 MIMO mode, use either a power supply (included) or a PoE 802.3at.2 radios – both in n modeFor 2x2 MIMO mode, use either a power supply (included) or PoE 802.3af.For 3x3 MIMO mode, use either a power supply (included) or a PoE 802.3at.
6Meru AP300 Guide © 2007 Meru Networks, Inc.Installation Requirements Figure 3: AP300 Bottom ViewAn array of holes on the mounting bracket allows the AP300 to be mounted on the wall and over junction boxes or molly bolts. There are holes for passing the PoE Ethernet or external power supply cable through the bracket if the bracket is mounted on a junction box. To complete this installation, you need the items listed in Table 3.Table 3: AP300 Installation ItemsInstallation Type Consumable Items RequiredHorizontal mounting NoneVertical mounting over a wall studzTwo #6 x 2" wood screws for a wood stud; or zTwo #6 x 1½" metal screws for a metal studzMounting bracketVertical mounting on sheetrockzTwo #6 x 1" screwszTwo #4-6 x 7/8" ribbed plastic wall anchorszMounting bracketHorizontal mounting below a hang-ing ceilingzTwo caddy fastenerszTwo plastic spacerszTwo keps nuts (with attached lock washer)zMounting bracketUsing existing Cisco 1230 series bracketszspecial screws - see Appendix AA5A65V DCCON LAN00209Ethernetportserialportpowerlock reset
Install the Access Points © 2007 Meru Networks, Inc. Installing the AP300 7 Table 4: AP300 Installation ToolsAdditional EquipmentA power source is provided with the AP300. If you want to use a PoE, you need to provide one of the following:z802.3af compliant PoE device (for 2x2 mode)z802.3at compliant PoE device (needed for 3x3 mode)Install the Access PointsSelect a LocationThe AP300 is only intended for installation in Environment A as defined in IEEE 802.3af. All interconnected equipment must be contained within the same building, including the inter-connected equipment's associated LAN connection. In addition, the AP300 should be mounted in a location that meets the following conditions:zRelatively unobstructed access to the stations the AP serves. Select a location with minimal physical obstructions between the AP and the wireless stations. In an office with cubicles, mounting the APs below a hanging ceiling (plenum testing is not complete at this time) or the wall near the ceiling provides the least obstructed communications path. For an external power supply connection, ensure the power source is near to where the AP300 will be mounted.Installation Type Tools RequiredHorizontal mounting NoneVertical mounting over a wall studzDrill z1/8"drill bitzScrewdriverz1/8"Allen wrenchVertical mounting on sheetrockzDrillz3/16" drill bitzScrewdriverz1/8"Allen wrenchHorizontal mounting below a hang-ing ceilingzScrewdriverzWrench or pliersz1/8"Allen wrenchUsing existing Cisco 1230 series bracketszScrewdriver
8Meru AP300 Guide © 2007 Meru Networks, Inc.Install the Access Points zAccess to wall outlet or a to a Power over Ethernet (PoE) connection to the network switch servicing the controller. Most installations receive the best coverage using the following guidelines:zInstall APs toward the center of the building.zDo not install APs near metal objects, such as heating ducts, metal doors, or electric service panels.zRelative to the ground, orient the antenna up or down, not sideways.Attach the AP300 AntennasThe AP300 has six external antenna ports, labeled 1 - 6. AP320 and AP311 use all six antennas. AP310 uses three antennas (1 - 3). Make sure that all external antennas and their associated wiring are located entirely indoors. The external antennas are not suitable for outside use.Figure 4: AP320 Antennas 1-6 Attach Standard AntennasAll standard attached antennas must be the same model. If you replace one antenna, replace them all. These antennas are supported:zAntenna Standard multiband, omni-directional white antenna (included)zStandard Antenna Gain ~ 2.2 dBi for 2.4 GHz,and 3 dBi for 5 GHzzRP SMA connectors for external antenna optionsMake sure that all external antennas and their associated wiring are located entirely indoors. The external antennas shipped are not suitable for outside use.Note:The previous guidelines are general guidelines. Each site has its own unique environment. Place access points accordingly.A2A2ALANRF1RF2200207123456
10 Meru AP300 Guide © 2007 Meru Networks, Inc.Install the Access Points Figure 6: Horizontal AP300Mount AP300 on a WallNote:If you are replacing AP150s, you can use the existing brackets: the AP150 and AP300 use the same bracket. If you are replacing AP200s, the AP300 bracket can be attached to the old bracket with shoulder screws (see Appendix A); you don’t have to remove the old brackets.The AP300 ships with the mounting bracket attached. To mount an AP300 on a wall:1. Using the bracket holes as a guide, mark the location on the wall for the two AP bracket mounting screws. If possible, center the mounting screws on a wall stud. If you do not center the mounting screws on a wall stud, use plastic wall anchors.2. Drill holes at the locations you marked:—3/16-inch holes if you are using plastic anchors—1/8-inch holes if you are using only the screws3. If you are using plastic anchors, install them in the holes.4. Screw in the screws most of the way.5. Mount the bracket on the screws, placing the circular portion of the keyhole mounts over the screw heads and sliding the bracket down.6. Connect one end of the Ethernet cable to the AP300 Ethernet port shown in Figure 7.A2A2ALANRF1RF2200207
Check AP300 LED Activity © 2007 Meru Networks, Inc. Installing the AP300 11 Figure 7: Connect AP300 to LAN7. Either connect an external power supply to the power connector and plug it into the wall, or connect an appropriate PoE power device to the Ethernet port (see Figure 7).Check AP300 LED ActivityAfter the AP300 is connected, the LEDs should light (see Figure 8).Figure 8: AP300 Status LEDsThe functions of the five LEDs are described in Table 5.When the AP300 is first connected to the controller and any time the access point is rebooted thereafter, the AP initializes with and then is programmed by the controller. When the AP is first powered up, all LEDs are green. Thereafter, the Status LED (see Figure 8) color reflects the various operating states (Table 5). A5A65V DCCON LAN00209Ethernet PortA5A4A3A3PWRSTATLANRF1RF200208power status LAN RF1 RF2
12 Meru AP300 Guide © 2007 Meru Networks, Inc.Configure AP300 Software Table 5: AP300 LED DescriptionsConfigure AP300 SoftwareYou can configure both the power source the AP300 will use and the channel width the AP300 will use. The default power source is 802.3af, and the default channel width is 20 MHz; these are the lowest (and slowest) settings. Increase range and throughput by changing MIMO mode to 3x3. The power supply option that you select determines whether or not you can use 3x3 MIMO. Be sure to change the power supply setting to either a DC power supply (provided) or a 802.11at PoE before changing MIMO mode to 3x3. Configure AP300 Using the CLIUse the CLI command configure ap to set the Power Supply Type and configure interface Dot11Radio to set the Channel Width, and MIMO Mode. For example:1. Access the controller from a browser by entering the IP address of the controller.2. Switch to configuration mode by entering terminal configuration at the CLI prompt. The prompt changes to controller name (config).3. Select an AP by entering the command ap #. For example:LED FunctionPower off—no powergreen—presence of powerStatusoff—no powergreen—booting stage 1blinking green and off—booting stage 2blinking green and white—discovering the controllerblinking green and blue—downloading a configuration from the controllerblinking blue and off—AP is online and enabled, working stateblinking red and yellow—failure; consult controller for alarm stateLANoff—no power, or no linkgreen—link status OK (at any speed)green/blinking—activity (at any speed)red—auto negotiation failureRadio 1Radio 2off—no radio presentgreen—radio enabledgreen blinking—data activityyellow—disabled or in scanning modered—failure
Configure AP300 Software © 2007 Meru Networks, Inc. Installing the AP300 13 default(config)# ap 1 *******changes to ap config****default(config-ap)# ? *******help lists options****boot-script Configure boot script for this AP.building Building location for this AP.connectivity Manage AP connectivity.contact Contact person for this AP.dataplane-mode Determine whether the data packets go through the controller or not.default Reset to default valuesdescription Description of AP.do Executes an IOSCLI command.end Save changes, and return to privileged EXEC mode.exit Save changes, and return to global configuration mode.floor Floor location for this AP.high-density-enable Enable high density.led Configure LED settings.link-probing-duration Duration AP waits before rebooting when controller link is down.location Location of this AP.mac-address Assign a new MAC address or pre-provision AP.model Assign AP HW type.no Disables various parameters.power-supply Power Supply mode for this AP.show Displays various parameters related to this AP.4. Set the power supply with the CLI command power supply. For example:default(config-ap)# power-supply ? *******help lists options****5V-DC 5V-DC for AP Power.802.3-af 802.3af Power Over Ethernet.802.3-at 802.3-at Power Over Ethernet.dual-802.3-af dual-802.3-af Power Over Ethernet.default(config-ap)# power-supply 5V-DC ***changes power to 5V***5. Exit configuration mode with the CLI command exit.\6. Switch to radio channel configuration with the CLI command interface Dot11Radio # #. For example:default(config-ap)# exitdefault(config)# interface Dot11Radio 1 1 ***switches to radio channel config***default(config-if-802)# ? ****help lists options*****admin-mode Administrative Mode.antenna-property Manage external wireless interface antennas.antenna-selection Antenna configuration.channel Configure the channel ID.channel-width Configure the Channel Width for 802.11ndefault Set various parameters to the default value.do Executes an IOSCLI command.end Save changes, and return to privileged EXEC mode.exit Save changes, and return to global configuration mode.fixed-channel Fix channel so it cannot be changed by auto-channel configuration.mimo-mode Configure the MIMO mode
14 Meru AP300 Guide © 2007 Meru Networks, Inc.Configure AP300 Software mode AP mode configuration.no Disables various parameters.power Transmit power in the format low,medium,high. For example, 20,20,20.preamble-short Enables short preamble.protection-cts-mode B/G protection mechanism.protection-mode bg protection mode.rf-mode Configure the Radio Frequency mode (802.11a, b, g, bg, an, or bgn).show Displays various parameters related to this wireless interface.7. Change channel width from 20 MHz (default) to 40 MHz with the CLI command channel-width. For example:default(config-if-802)# channel-width ? ***help shows options***20-mhz 20 MHz.40-mhz-extension-channel-above 40 MHz Extension channel above.40-mhz-extension-channel-below 40 MHz Extension channel below.default(config-if-802)# channel-width above 40 MHz Extension channel ****changes channel width****8. Change MIMO Mode from 2x2 (default) to 3x3 with the mimo-mode 3x3 command. For example: default(config-if-802)# mimo-mode 3x3 *****changes MIMO ****default(config-if-802)# enddefault# defaultConfigure AP300 Using the GUIFollow these steps to change Power Supply Type, Channel Width, and MIMO Mode using the GUI:1. Enter the IP address of the controller in your browser. You see the controller GUI interface.2. From the controller GUI, click Configuration > Devices > APs. The AP Table shown in Figure 9 is displayed.
Configure AP300 Software © 2007 Meru Networks, Inc. Installing the AP300 15 Figure 9: AP Table Configuration Window3. Click the arrow that corresponds to the AP300 to change. The AP configuration for that AP is displayed. See Figure 10.Figure 10: Changing Power Supply Type 4. Click the Power Supply Type drop-down list and select one of the following options. The included DC power block corresponds to the option 5V DC.
16 Meru AP300 Guide © 2007 Meru Networks, Inc.Configure AP300 Software —802.3-af: Default power supply. Select this when using a traditional PoE. This power supply type only supports 2x2 MIMO mode.—802.3-at: Select when using a higher-powered, next generation PoE. This power supply type supports 3x3 MIMO mode.—5V-DC: Select when AP300 is plugged into a wall outlet. This power supply type supports 3x3 MIMO mode.—dual-802.3: Select when using a dongle that combines power from two traditional PoEs. This power supply type supports 3x3 MIMO mode.5. Click OK.6. Next, configure MIMO mode and Channel Width. Click the Wireless Interface tab. You see the Wireless Interface Configuration window shown in Figure 11.Figure 11: Wireless Interface Tab - Set MIMO Mode and Channel Width 7. Configure RF Band Selection by selecting a value from the drop-down list. To configure the band as N only, select a setting that includes N and change the data rates setting to make only N viable.8. Configure MIMO mode by clicking the drop-down list and selecting either 2x2 or 3x3. Be sure you have already configured an appropriate power source for 3x3 MIMO Mode. 3x3 MIMO Mode produces higher reliability, range, and speed but both settings (2x2 and 3x3) should approach 320 mbps.Note:The Short Preamble Setting affects 11b clients only. The Protection Mechanism setting has no effect at this time.
Troubleshooting © 2007 Meru Networks, Inc. Installing the AP300 17 9. Configure Channel Width by clicking the drop-down list and selecting either 40 MHz Extension channel above or 40 MHz Extension channel below. The ‘channel above’ and ‘channel below’ are relative to the value set in the Channel control setting (see Figure 11, the third setting from the top). This configures the channel bonding.10. Click OK.TroubleshootingzIf an AP320 continually reboots or demonstrates other unusual behavior, and MIMO Mode is set to 3x3, there may be a mismatch of power and MIMO Mode. Make sure that you have an appropriate power source configured, as well as attached to an AP320 with MIMO Mode set to 3x3.zWhen RF band selection is set to 802.11n, the security mode can only be set at clear, wpa2 or wpa2psk. This is an 802.11n restriction.zThe ChannelWidth field value 40 Mhz-extension-channel-above is only applicable if the extension channel above is available in the country code. For example, A_EXT_CHANNELS=36:40 case, 40 Mhz-extension-channel-above configuration is valid for channel number 36. Currently we support extension channels in only the US country code. In addition, the default channel numbers for RF mode BG or A mode are changed in the US country code (DEFAULT_B_CHANNEL=6, DEFAULT_A_CHANNEL=36).
18 Meru AP300 Guide © 2007 Meru Networks, Inc.Troubleshooting
© 2007 Meru Networks, Inc. AP300 Brackets 19 Appendix AAP300 BracketsThe AP300 is designed to be used with brackets supplied by other vendors. Meru APs are compatible with the Cisco 1230 series brackets, but the 1240 and 1250 series brackets are new and not compatible. If you reuse a Cisco 1230 series bracket, follow these steps:1. Obtain three of the screws shown in Figure 12.Figure 12: Shoulder Screw (specification front and side)2. Insert the three screws into the locations indicated in Figure 13. USI PN 48-300024-01 Description: UNC#10-32,1/4*1/8,HS,BND,303SS,NO,SHOLDRDOC NO:2A-003225 REV: A1 DATE: 7th July 2005Suspended ceilingcable accessWall cable accessShoulder screws
20 Meru Access Point and Radio Switch Installation Guide © 2007 Meru Networks, Inc. Figure 13: Location of Shoulder Screws3. Slide the Meru bracket with shoulder screws onto the Cisco bracket.
© 2007 Meru Networks, Inc. Specifications 21 Appendix BSpecificationsThis chapter provides specifications for Meru Access Points and contains the following sections:zWireless Interface for All APszEthernet Interface for All Meru APszPhysical Description for All Meru APsWireless Interface for All Meru APsTable 6: Wireless Interface SpecificationsFeature DetailsWireless Standards z802.11a, 802.11b, 802.11g, 802.11nAntennas zTwo to six external antennas. Omni-directional and direc-tional antennas for specific coverage requirementsWireless Medium AccesszWi-Fi Compliant 802.11 MAC standardPower Management zPower-save mode for clients in both QoS mode and non-QoS modeFrame SizezPeak frame size of > 2346 byteszFragmentation and reassembly of 802.11/Ethernet framesClient Activities Sup-portedzActive scanning and passive scanningzPre-authenticationzPower-save mode supported
22 Meru Access Point and Radio Switch Installation Guide © 2007 Meru Networks, Inc.Ethernet Interface for All Meru APs Ethernet Interface for All Meru APsPhysical Description for All Meru APsPhysical specifications for Meru Access Points are provided in the access point Data Sheet. Contact your Meru sales engineer for a copy of the document.Feature DetailWireline StandardzOne Ethernet (IEEE 802.3) interface, supporting half-duplex and full-duplex modeszSupports the Power over Ethernet (PoE) IEEE 802.3af standard
© 2007 Meru Networks, Inc. Regulatory Information 23 Appendix CRegulatory InformationThe Meru Networks, Inc. Meru Access Points (APs) must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documen-tation that comes with the product. For country-specific approvals, see below. Meru Networks, Inc. is not responsible for any radio or television interference caused by unauthorized modification of APs, or the substitution or attachment of connecting cables and equipment other than that specified by Meru Networks, Inc. The correc-tion of interference caused by such unauthorized modification, substitution or attachment is the responsibility of the user. Meru Networks, Inc. and its authorized resellers or distributors are not liable for any damage or violation of government regulations that may arise from the user failing to comply with these guidelines.USA — Federal Communications Commission (FCC)FCC Radiation Exposure StatementCaution!The radiated output power of the Meru Networks, Inc. devices is well below the FCC radio frequency exposure limits. However, the Meru Net-works, Inc. Meru Access Points should be used in such a manner that the potential for human contact during normal operation is minimized. To avoid the possibility of exceeding the FCC radio frequency exposure limits, you should keep a distance of at least 20 cm between you (or any other person in the vicinity) and the Access Point antennas.
24 Meru Access Point and Radio Switch Installation Guide © 2007 Meru Networks, Inc.USA — Federal Communications Commission (FCC) Radio Frequency Interference RequirementsInterference StatementThese devices comply with Part 15 of the FCC Rules. Operation of the devices is subject to the following two conditions: (1) The devices may not cause harmful inter-ference, and (2) The devices must accept any interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa-tion. This equipment generates, uses, and can radiate radio frequency energy. If the equipment is not installed and used in accordance with the instructions, the equip-ment may cause harmful interference to radio communications. There is no guar-antee, however, that such interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment off and on), the user is encour-aged to try to correct the interference by taking one or more of the following measures:Relocate this device. Increase the separation between the device and the receiver. Connect the device into an outlet on a circuit different from that of other electronics.Consult the dealer or an experienced radio technician for help. This device must not be co-located or operating in conjunction with any other antenna or transmitter.Note:Meru Networks Meru Access PointThese devices are restricted to indoor use because they operate in the 5.15 to 5.25 GHz frequency range. The FCC requires such products to be used indoors for the frequency range 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. Note:The Meru Networks Meru Access Point must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. Any other installation or use may violate FCC Part 15 regulations. Modifications not expressly approved by Meru Networks, Inc. could void your authority to operate the equip-ment.
Canada. Industry Canada (IC) © 2007 Meru Networks, Inc. Regulatory Information 25Canada. Industry Canada (IC)This device complies with RSS210 of Industry Canada.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interfer-ence that may cause undesired operation of this device. L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. The term "IC" before the equipment certification number only signifies that the Industry Canada technical specifications were met. To reduce the potential radio interference to other users, the antenna type and gain should be chosen so that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication. To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Pour empecher que cet appareil cause du brouillage au service faisant l’objet d’une licence, il doit etre utilze a l’interieur et devrait etre place lin des fenetres afin de Fournier un ecram de blindage maximal. Si le matriel (ou son antenne d’emission) est installe a l’exterieur, il doit faire l’objet d’une licence. Caution!Exposure to Radio Frequency Radiation.The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit an RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s website http://www.hc-sc.gc.ca/rpb. Note:Meru Networks Meru Access PointsThese devices are restricted to indoor use because they operate in the 5.15 to 5.25 GHz frequency range. Industry Canada requires such products to be used indoors for the frequency range 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite sys-tems.
28 Meru Access Point and Radio Switch Installation Guide © 2007 Meru Networks, Inc.IEEE 802.11b/gThe channel identifiers, channel center frequencies, and regulatory domains of each IEEE 802.11b/g channel are listed in Table 8.44 5220 X -46 523048 524052 526056 528060 530064 5320149 5745 X -153 5765 X -157 5785 X -161 5805 X -165 5825 X -Table 7: IEEE 802.11a Channels (Continued)ChannelNumberFrequency in MHzRegulatory DomainsAmericas JapanNote:Mexico is included in the Americas regulatory domain; however, channels 1 through 8 are for indoor use only while channels 9 through 11 can be used indoors and outdoors. Users are responsible for ensuring that the channel set configuration complies with the regulatory standards of Mexico.
© 2007 Meru Networks, Inc. Channels 29Table 8: IEEE 802.11b/g Channels ChannelNumberFrequencyin MHzRegulatory DomainsAmericas EMEA Israel China Japan1 2412 X X2 2417 X X3 2422 X X4 2427 X X5 2432 X X6 2437 X X7 2442 X X8 2447 X X9 2452 X X10 2457 X X11 2462 X X12 2467 - X13 2472 - X14 2484 -X(for 802.11b only)
30 Meru Access Point and Radio Switch Installation Guide © 2007 Meru Networks, Inc.IEEE 802.11nThe channel identifiers, channel center frequencies, and regulatory domains of each IEEE 802.11b/g channel are listed in Table 9.Table 9: IEEE 802.11n Channels ChannelNumberFrequency in MHz Regulatory DomainsNorth America ETSIIsraelJapan(-P) China1 2412 X X2 2417 X X3 2422 X X4 2427 X X5 2432 X X6 2437 X X7 2442 X X8 2447 X X9 2452 X X10 2457 X X11 2462 X X12 2467 - X
© 2007 Meru Networks, Inc. Channels 3113 2472 - X14 2484 -36 5180 X X40 5200 X X44 5220 X XChannelNumberFrequency in MHz Regulatory DomainsNorth America ETSIIsraelJapan(-P) China149 5745 X - - X153 5765 X - - X157 5785 X - - X161 5805 X - -- X
33 MERU NETWORKS, INC.Limited Product WarrantyThis Limited Product Warranty applies to the original end-user customer of the Meru product which you purchased for your own use, and not for resale (“Product”), from Meru Networks, Inc. (“Meru”) or its authorized reseller (“Reseller”). Limited Warranties—One-year limited hardware warranty: Meru warrants to you that Meru hardware (other than Third Party Products as described below) will be free from defects in materials and workmanship for a one-year period after the date of delivery of the applicable product to you from Meru or its Reseller (the “Hardware Warranty Period”). If Meru receives written notice from you of such defects during the Hardware Warranty Period, Meru will, at its option, either repair or replace Meru hardware that Meru determines to be defective. Replacement products may be remanufac-tured units, and will be warranted for the remainder of the original Hardware Warranty Period, or if greater, for thirty days from delivery of such replacement. Should Meru be unable to repair or replace the Meru hardware, Meru (or its Reseller, as applicable) will refund to you the purchase price of the Product. —90-Day Limited Software Warranty: Meru warrants to you that, for a 90-day period after the date of delivery of the applicable product to you from Meru or its Reseller (the “Software Warranty Period”), when properly installed and used, (a) the media on which the Meru software is provided will be free from defects in materials or workmanship; and (b) the Meru software will substantially conform to the functional specifications in the applicable documentation. If Meru receives written notice from you of a breach of this warranty during the Software Warranty Period and is able to reproduce the defect, Meru will, at its option, either repair or replace the defective Meru software. Should Meru be unable to repair or replace the Meru software, Meru (or its Reseller, as applicable) will refund to you the purchase price of the Product.ExclusionsThe warranty on the Product shall not apply to defects resulting from the following:—Alteration or modification of the Product in any way, including without limitation configuration with software or components other than those supplied by Meru or integration with parts other than those supplied by Meru.—Abuse, damage or otherwise being subjected to problems caused by negligence or misapplication (including without limitation improper or inadequate maintenance or calibration), relocation of the products (including without limitation damage caused by use of other than Meru shipping containers), or use of the products other than as specified in the applicable Meru product docu-mentation (including without limitation incompatible operating environments and systems), or improper site preparation or maintenance.—Damage as a result of accidents, extreme power surge, extreme electromagnetic field, acts of nature or other causes beyond the control of Meru.—Use of the Product with software, interfacing, parts or supplies not supplied by Meru.The warranty on the Product does not apply if the Product is sold, or in the case of software, licensed, for free for evaluation or demonstration purposes.
34 Meru Access Point and Radio Switch Installation Guide Meru expressly disclaims any warranty or obligation to support the Product for all operating environments – for example, as illustration and not limitation, Meru does not warrant or ensure interoperability of the Product with future telecommunication systems or other future software or hardware.You understand and acknowledge that the Products may generate, use or radiate radio frequency energy and may interfere with radio communications and/or radio and television receptions if is not used and/or installed in accordance with the documentation for such products. WHILE MERU USES COMMERCIALLY REASONABLE EFFORTS TO ENSURE COMPLIANCE OF THE PRODUCTS WITH APPLICABLE UNITED STATES FEDERAL COMMUNICATIONS COMMISSION AND PROTECT AGAINST HARMFUL INTERFERENCES, YOU ACKNOWLEDGE AND AGREE THAT INTERFERENCES WITH RADIO COMMUNICATIONS AND/OR RADIO AND TELEVISION RECEPTIONS MAY OCCUR AND THAT MERU WILL NOT BE LIABLE FOR ANY DAMAGES OR INCONVENIENCE BASED ON SUCH INTERFERENCES. Third Party Products - The above Limited Warranties are exclusive of products manufactured by third parties (“Third Party Products”). If such third party manufacturer provides a separate warranty with respect to the Third Party Product, Meru will include such warranty in the packaging of the Meru Product. Return proceduresTo obtain warranty service you must: (a) obtain a return materials authorization number (“RMA#”) from Meru by contacting support@merunetworks.com, and (b) deliver the Product, in accordance with the instructions provided by Meru, along with proof of purchase in the form of a copy of the bill of sale including the Product’s serial number, contact information, RMA# and detailed description of the defect, in either its original package or packaging providing the Product with a degree of protection equivalent to that of the original packaging, to Meru at the address below. You agree to obtain adequate insurance to cover loss or damage to the Product during shipment. If you obtain an RMA# and return the defective Product as described above, Meru will pay the cost of returning the Product to Meru. Otherwise, you agree to bear such cost, and prior to receipt by Meru, you assume risk of any loss or damage to the Product. Meru is responsible for the cost of return shipment to you if the Meru Product is defective.Returned products which are found by Meru to be not defective, returned out-of-warranty or otherwise ineligible for warranty service will be repaired or replaced at Meru’s standard charges and shipped back to you at your expense.At Meru’s sole option, Meru may perform repair service on the Product at your facility, and you agree to provide Meru with all reasonable access to such facility and the Product, as required by Meru. On-site repair service may be available and is governed by the specific terms of your purchase.All replaced parts, whether under warranty or not, are the property of Meru. Warranty limitationsTHE WARRANTIES SET FORTH ABOVE ARE EXCLUSIVE AND NO OTHER WARRANTY, WHETHER WRITTEN OR ORAL, IS EXPRESSED OR IMPLIED BY MERU, TO THE MAXIMUM EXTENT PERMITTED BY LAW. THERE ARE NO OTHER
35 WARRANTIES RESPECTING THE PRODUCT AND DOCUMENTATION AND SERVICES PROVIDED UNDER THIS AGREEMENT, INCLUDING WITHOUT LIMITATION ANY WARRANTY OF DESIGN, MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (EVEN IF MERU HAS BEEN INFORMED OF SUCH PURPOSE), TITLE OR AGAINST INFRINGEMENT OF THIRD PARTY RIGHTS. IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED UNDER APPLICABLE LAW, THEN SUCH IMPLIED WARRANTY SHALL BE LIMITED IN DURATION TO THE HARDWARE AND SOFTWARE WARRANTY PERIODS DESCRIBED ABOVE. NO AGENT OF MERU IS AUTHORIZED TO ALTER OR EXCEED THE WARRANTY OBLIGATIONS OF MERU.MERU SPECIFICALLY DOES NOT WARRANT THAT THE MERU SOFTWARE WILL BE ERROR FREE OR OPERATE WITHOUT INTERRUPTION. THE REMEDIES IN THIS LIMITED PRODUCT WARRANTY ARE YOUR SOLE AND EXCLUSIVE REMEDIES, AND MERU’S SOLE AND EXCLUSIVE LIABILITY, FOR BREACH OF THE HARDWARE OR SOFTWARE WARRANTY SET FORTH ABOVE.Limitations of LiabilityYou acknowledge and agree that the consideration which you paid to Meru does not include any consideration by Meru of the risk of consequential, indirect or incidental damages which may arise in connection with your use of, or inability to use, the Product. THUS, MERU AND ITS RESELLER WILL NOT BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL, PUNITIVE OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION LOST PROFITS, LOST BUSINESS, LOST DATA, LOSS OF USE, OR COST OF COVER INCURRED BY YOU ARISING OUT OF OR RELATED TO YOUR PURCHASE OR USE OF, OR INABILITY TO USE, THIS PRODUCT OR THE SERVICES, UNDER ANY THEORY OF LIABILITY, WHETHER IN AN ACTION IN CONTRACT, STRICT LIABILITY, TORT (INCLUDING NEGLIGENCE) OR OTHER LEGAL OR EQUITABLE THEORY, EVEN IF MERU OR ITS RESELLER KNEW OR SHOULD HAVE KNOWN OF THE POSSIBILITY OF SUCH DAMAGES. IN ANY EVENT, THE CUMULATIVE LIABILITY OF MERU OR ITS RESELLER FOR ALL CLAIMS WHATSOEVER RELATED TO THE PRODUCT OR THE SERVICE WILL NOT EXCEED THE PRICE YOU PAID FOR THE PRODUCT OR SERVICES GIVING RISE TO SUCH CLAIMS.THE LIMITATIONS SET FORTH HEREIN ARE INTENDED TO LIMIT THE LIABILITY OF MERU AND ITS RESELLERS AND SHALL APPLY NOTWITHSTANDING ANY FAILURE OF ESSENTIAL PURPOSE OF ANY LIMITED REMEDY.The jurisdiction applicable to you may not allow the limitations of liability or damages set forth above, in which case such limitation shall only apply to you to the extent permitted in such jurisdiction.Additional InformationThis Limited Product Warranty shall be governed by and construed in accordance with the laws of the State of California, U.S.A., exclusive of its conflict of laws principles. The U.N. Convention on Contracts for the International Sale of Goods shall not apply.
36 Meru Access Point and Radio Switch Installation Guide This Limited Product Warranty is the entire and exclusive agreement between you and Meru with respect to its subject matter, and any modification or waiver of any provision of this statement is not effective unless expressly set forth in writing by an authorized representative of Meru.All inquiries or claims made under this Limited Product Warranty must be sent to Meru at the following address:Meru Networks Inc.,894 Ross Drive, CA 94087, USATel: 408-215-5300Fax: 408-215-5301Email: support@merunetworks.com
Meru Networks, Inc.894 Ross DriveSunnyvale, CA 94087408-215-5300www.merunetworks.com

Navigation menu