Mercury Networks Q1000-25-5 Quantum 1000 Base Station User Manual

Mercury Networks, LLC Quantum 1000 Base Station Users Manual

Users Manual

Quantum 1000 Base Station User Quantum 1000 Base Station Revision History Rev No. Issue Date Summary of Change1.0 July 09 Initial Draft 1.1 24 Jul 09 Significant Changes Added Quantum 1000 Base Station User Guide Rev 1.1, Page Quantum 1000 Base Station User Guide Summary of Change Author Sajed SaeedChanges Added Steven Chaganis Rev 1.1, Page 1 of 70 Quantum 1000 Base Station Sajed Saeed Steven Chaganis
Quantum 1000 Base Station User It is hoped that this document will be useful in understanding and using the PureWavenote that the information provided herein is subject to change without notice. Always refer to the current set of Release Notes for the most the current features as they relate to the contained within this User Guide. Quantum 1000 Base Station User Guide Rev 1.1, Page NOTICE that this document will be useful in understanding and using the PureWave System. Please note that the information provided herein is subject to change without notice. Release Notes for the most upto date information and a as they relate to the PureWave system. These may be different to the information Rev 1.1, Page 2 of 70 System. Please and a description of These may be different to the information
Quantum 1000 Base Station User It is the intention of PureWave Networks to ensure that this equipment is tested to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmfuluses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there isthat interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to c • Re-orient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to whichconnected. • Consult the dealer or an experienced radio/TV technician for help. Shielded cables and I/O cords must be used for this equipment to comply with the relevant FCC regulations. Changes or modifications not expressly approved inauthority to operate this equipment. Note: This device must be professionally installed Quantum 1000 Base Station User Guide Rev 1.1, Page REGULATORY NOTICE It is the intention of PureWave Networks to ensure that this equipment is tested to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there isthat interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:orient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is Consult the dealer or an experienced radio/TV technician for help. Shielded cables and I/O cords must be used for this equipment to comply with the relevant FCC Changes or modifications not expressly approved in writing by PureWave Networks may void the user's authority to operate this equipment. This device must be professionally installed. Rev 1.1, Page 3 of 70 It is the intention of PureWave Networks to ensure that this equipment is tested to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and orrect the interference by one or more of the following measures: the receiver is Shielded cables and I/O cords must be used for this equipment to comply with the relevant FCC writing by PureWave Networks may void the user's
Quantum 1000 Base Station User PROPRIETARY STATEMENT © PureWave™ Networks, 2003-2007. All rights reserved. PureWave™ Networks has prepared this manual for use by PureWave Networks personnel, licensees, customers and customers of customers. The information contained herein is the property of PureWave Networks and shall neither be reproduced in whole nor in part without prior written approval from Pure PureWave Networks reserves the right to make changes without notice to the specifications and materials contained herein, and shall not be responsible for any damages caused by reliance on the materialpresented, including, but not limited WARRANTY STATEMENT Hardware PureWave Inc (“PureWave” or the “Company”) warrants to the endproduct will conform in all material respects to the specifications provided with the hardware and will be free from defects in workmanship and materials, under normal use and serfrom the date of original shipment by PureWave. PureWave's sole obligation under this limited warranty shall be, at PureWave's option, to repair the defective product or part, deliver to Customer an equivalent product or paor if neither of the two foregoing options is reasonably possible, refund to Customer the purchase price paid for the defective product. All products that are replaced will become the property of PureWave. Replacement products may be new or reconditioned. PureWave's obligations hereunder are conditioned upon the returned of affected articles in accordance with PureWave's Return Material Authorization (RMA) procedures. Subject to the limitations and conditions herein acompleted the steps outlined below in Section 2, PureWave will evaluate each returned Product and will use reasonable commercial efforts to either, in its discretion, repair or replace products confirmed by PureWave as non-conforming that are covered under the warranty provided in the Supply Agreement. PureWave shall be responsible for shipping the repaired or replaced Product to Customer. PureWave will use reasonable commercial efforts to ship repaired or repdays of its receipt, however, the allegedly nonany replacement unit will be shipped. The above warranty will apply to any replaced or repaired product the remainder of the initial warranty period, whichever is longer.Software PureWave warrants to the Customer that for a period of ninety (90) days from your receipt of the Product (the “Warranty Period”) the Software If the Software fails to comply with the warranty set forth above, your exclusive remedy will be, at the option of PureWave (i) a reasonable effort by PureWave to make the Software perform suaccordance with the Documentation, or (ii) return of the purchase price. This limited warranty applies only if you return all copies of the Product, together with proof of purchase, to PureWave during the Warranty Period. This limited warranty is VOID if failure of the Software is due to modification of the Software not made by PureWave, or the abuse or misapplication of the Software. is error free, that the Customer will be able to operate the Sothat the Software or any equipment, system or network on which the Software is used will be free of vulnerability to intrusion or attack. Quantum 1000 Base Station User Guide Rev 1.1, Page 2007. All rights reserved. PureWave™ Networks has prepared this ual for use by PureWave Networks personnel, licensees, customers and customers of customers. The information contained herein is the property of PureWave Networks and shall neither be reproduced in whole nor in part without prior written approval from PureWave Networks. PureWave Networks reserves the right to make changes without notice to the specifications and materials contained herein, and shall not be responsible for any damages caused by reliance on the materialpresented, including, but not limited to, typographical, arithmetic and listing errors. ” or the “Company”) warrants to the end-user (“Customer”) that this hardware product will conform in all material respects to the specifications provided with the hardware and will be free from defects in workmanship and materials, under normal use and service, for a period of 365 days from the date of original shipment by PureWave. PureWave's sole obligation under this limited warranty shall be, at PureWave's option, to repair the defective product or part, deliver to Customer an equivalent product or part to replace the defective item, or if neither of the two foregoing options is reasonably possible, refund to Customer the purchase price paid for the defective product. All products that are replaced will become the property of PureWave. oducts may be new or reconditioned. PureWave's obligations hereunder are conditioned upon the returned of affected articles in accordance with PureWave's Return Material Authorization Subject to the limitations and conditions herein and in the Supply Agreement, after Customer has completed the steps outlined below in Section 2, PureWave will evaluate each returned Product and will use reasonable commercial efforts to either, in its discretion, repair or replace products confirmed by conforming that are covered under the warranty provided in the Supply Agreement. PureWave shall be responsible for shipping the repaired or replaced Product to Customer. PureWave will use reasonable commercial efforts to ship repaired or replacement Product within twenty (30) business days of its receipt, however, the allegedly non-conforming Product must be received by PureWave before any replacement unit will be shipped. The above warranty will apply to any replaced or repaired product or part for 90 days from shipment, or the remainder of the initial warranty period, whichever is longer. PureWave warrants to the Customer that for a period of ninety (90) days from your receipt of the Product (the “Warranty Period”) the Software will perform substantially in accordance with the Documentation.If the Software fails to comply with the warranty set forth above, your exclusive remedy will be, at the option of PureWave (i) a reasonable effort by PureWave to make the Software perform suaccordance with the Documentation, or (ii) return of the purchase price. This limited warranty applies only if you return all copies of the Product, together with proof of purchase, to PureWave during the Warranty anty is VOID if failure of the Software is due to modification of the Software not made by PureWave, or the abuse or misapplication of the Software. PureWave does not warrant that the Software is error free, that the Customer will be able to operate the Software without problems or interruptions or that the Software or any equipment, system or network on which the Software is used will be free of Rev 1.1, Page 4 of 70 2007. All rights reserved. PureWave™ Networks has prepared this ual for use by PureWave Networks personnel, licensees, customers and customers of customers. The information contained herein is the property of PureWave Networks and shall neither be reproduced PureWave Networks reserves the right to make changes without notice to the specifications and materials contained herein, and shall not be responsible for any damages caused by reliance on the material user (“Customer”) that this hardware product will conform in all material respects to the specifications provided with the hardware and will be vice, for a period of 365 days PureWave's sole obligation under this limited warranty shall be, at PureWave's option, to repair the rt to replace the defective item, or if neither of the two foregoing options is reasonably possible, refund to Customer the purchase price paid for the defective product. All products that are replaced will become the property of PureWave. oducts may be new or reconditioned. PureWave's obligations hereunder are conditioned upon the returned of affected articles in accordance with PureWave's Return Material Authorization nd in the Supply Agreement, after Customer has completed the steps outlined below in Section 2, PureWave will evaluate each returned Product and will use reasonable commercial efforts to either, in its discretion, repair or replace products confirmed by conforming that are covered under the warranty provided in the Supply Agreement. PureWave shall be responsible for shipping the repaired or replaced Product to Customer. PureWave will lacement Product within twenty (30) business conforming Product must be received by PureWave before or part for 90 days from shipment, or PureWave warrants to the Customer that for a period of ninety (90) days from your receipt of the Product will perform substantially in accordance with the Documentation. If the Software fails to comply with the warranty set forth above, your exclusive remedy will be, at the option of PureWave (i) a reasonable effort by PureWave to make the Software perform substantially in accordance with the Documentation, or (ii) return of the purchase price. This limited warranty applies only if you return all copies of the Product, together with proof of purchase, to PureWave during the Warranty anty is VOID if failure of the Software is due to modification of the Software not made by PureWave does not warrant that the Software ftware without problems or interruptions or that the Software or any equipment, system or network on which the Software is used will be free of
Quantum 1000 Base Station User Additional Conditions Notwithstanding anything else herein or otherwise, Pto this RMA Policy from time to time. Further, the wireless link with an onsite Customer technician while the Products are in their original nonconforming state. This process might assist Customer in understanding and troubleshooting the issue. If PureWave was not afforded the opportunity to troubleshoot an allegedly nonoriginal non-conforming state, PureWave may approve or rejand such Products are not eligible for advance replacement. No Fault Found Notwithstanding Sections 2 and 3 above, if PureWave cannot duplicate any alleged nonProduct will be returned to the Customer, at Customer’s expense, as "No Fault Found." PureWave reserves the right to charge a testing fee in addition to all shipping costs incurred by PureWave in connection with a returned product that PureWave determines as “No Fault Found,” and any spayment must be received by PureWave prior to return shipment of the applicable Product to Customer. Warranty Limitations PureWave’s warranties do not apply to any product (hardware or software) which has (a) been subjected to abuse, misuse, neglect, accident, or mishandling, (b) been opened, repaired, modified, or altered by anyone other than PureWave, (c) been used for or subjected to applications, environments, or physical or electrical stress or conditions other than as intended and recommended by Purimproperly stored, transported, installed, or used, or (e) had its serial number or other identification markings altered or removed. Warranty Disclaimer PURWAVE’S SPECIFIC WARRANTIES SUMMARIZED ABOVE ARE THE ONLY WARRANTIES GIVEN BY PUREWAVE WITH RESPECT TO ITS PRODUCTS (HARDWARE AND SOFTWARE) AND ARE GIVEN IN LIEU OF ANY AND ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED, STATUTORY, OR ARISING BY CUSTOM, TRADE USAGE, OR COURSE OF DEALING, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIPARTICULAR PURPOSE, AND PUREWAVE DISCLAIMS ANY AND ALL OTHER WARRANTIES TO THE MAXIMUM EXTENT PERMITTED BY LAW. Without limiting the generality of the foregoing sentence, PureWave makes no warranty or representation, disclaims all liability and responsibility for, (a) the operation, compliance, labeling, or packaging of any of its products under the laws of any jurisdiction outside of the United States of America and (b) the regulatory compliance of any products in any jurisdiction in which it has not specifically identified compliance or the use of any product in any jurisdiction in any manner other than as contemplated in the regulatory certifications and approvals for that prodwarranty cannot be excluded, such warranty is limited in duration to the warranty period. The disclaimer and exclusion applies even if the express warranty OBTAINING WARRANTY SERVICERMA Number Customer must contact the Company, service authorization. When contacting PureWavedescription and serial number and a description of the problem. complete a “Return Material Authorization (RMA)” form to initiate the request. Full instructions as to to complete and where to send the form are provided on the form. Date of proof of purchase from PureWave will be required. Quantum 1000 Base Station User Guide Rev 1.1, Page Notwithstanding anything else herein or otherwise, PureWave reserves the right to establish amendments to this RMA Policy from time to time. Further, PureWave Technical Support may prefer to troubleshoot the wireless link with an onsite Customer technician while the Products are in their original nonrming state. This process might assist Customer in understanding and troubleshooting the issue. If PureWave was not afforded the opportunity to troubleshoot an allegedly non-conforming Product in conforming state, PureWave may approve or reject the RMA request in its sole discretion, and such Products are not eligible for advance replacement. Notwithstanding Sections 2 and 3 above, if PureWave cannot duplicate any alleged nontomer, at Customer’s expense, as "No Fault Found." PureWave reserves the right to charge a testing fee in addition to all shipping costs incurred by PureWave in connection with a returned product that PureWave determines as “No Fault Found,” and any spayment must be received by PureWave prior to return shipment of the applicable Product to Customer. PureWave’s warranties do not apply to any product (hardware or software) which has (a) been subjected ident, or mishandling, (b) been opened, repaired, modified, or altered by anyone other than PureWave, (c) been used for or subjected to applications, environments, or physical or electrical stress or conditions other than as intended and recommended by PureWave, (d) been improperly stored, transported, installed, or used, or (e) had its serial number or other identification PURWAVE’S SPECIFIC WARRANTIES SUMMARIZED ABOVE ARE THE ONLY WARRANTIES GIVEN WAVE WITH RESPECT TO ITS PRODUCTS (HARDWARE AND SOFTWARE) AND ARE GIVEN IN LIEU OF ANY AND ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED, STATUTORY, OR ARISING BY CUSTOM, TRADE USAGE, OR COURSE OF DEALING, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND PUREWAVE DISCLAIMS ANY AND ALL OTHER WARRANTIES TO THE MAXIMUM EXTENT PERMITTED BY LAW. Without limiting the generality of the foregoing sentence, PureWave makes no warranty or representation, either expressed or implied, as to, and disclaims all liability and responsibility for, (a) the operation, compliance, labeling, or packaging of any of its products under the laws of any jurisdiction outside of the United States of America and (b) the latory compliance of any products in any jurisdiction in which it has not specifically identified compliance or the use of any product in any jurisdiction in any manner other than as contemplated in the regulatory certifications and approvals for that product in that jurisdiction. To the extent an implied warranty cannot be excluded, such warranty is limited in duration to the warranty period. The disclaimer and exclusion applies even if the express warranty fails of its essential purpose. SERVICE Customer must contact the Company, by sending an e-mail to rma@pwnets.com to obtain warranty When contacting PureWave for support, please be prepared to provide the product description and serial number and a description of the problem. The Customer will be expected to complete a “Return Material Authorization (RMA)” form to initiate the request. Full instructions as to to complete and where to send the form are provided on the form. Date of proof of purchase from Rev 1.1, Page 5 of 70 ureWave reserves the right to establish amendments PureWave Technical Support may prefer to troubleshoot the wireless link with an onsite Customer technician while the Products are in their original non-rming state. This process might assist Customer in understanding and troubleshooting the issue. If conforming Product in ect the RMA request in its sole discretion, Notwithstanding Sections 2 and 3 above, if PureWave cannot duplicate any alleged non-conformity, the tomer, at Customer’s expense, as "No Fault Found." PureWave reserves the right to charge a testing fee in addition to all shipping costs incurred by PureWave in connection with a returned product that PureWave determines as “No Fault Found,” and any such payment must be received by PureWave prior to return shipment of the applicable Product to Customer. PureWave’s warranties do not apply to any product (hardware or software) which has (a) been subjected ident, or mishandling, (b) been opened, repaired, modified, or altered by anyone other than PureWave, (c) been used for or subjected to applications, environments, or physical or eWave, (d) been improperly stored, transported, installed, or used, or (e) had its serial number or other identification PURWAVE’S SPECIFIC WARRANTIES SUMMARIZED ABOVE ARE THE ONLY WARRANTIES GIVEN WAVE WITH RESPECT TO ITS PRODUCTS (HARDWARE AND SOFTWARE) AND ARE GIVEN IN LIEU OF ANY AND ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED, STATUTORY, OR ARISING BY CUSTOM, TRADE USAGE, OR COURSE OF DEALING, INCLUDING ES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND PUREWAVE DISCLAIMS ANY AND ALL OTHER WARRANTIES TO THE MAXIMUM EXTENT PERMITTED BY LAW. Without limiting the generality of the foregoing either expressed or implied, as to, and disclaims all liability and responsibility for, (a) the operation, compliance, labeling, or packaging of any of its products under the laws of any jurisdiction outside of the United States of America and (b) the latory compliance of any products in any jurisdiction in which it has not specifically identified compliance or the use of any product in any jurisdiction in any manner other than as contemplated in the uct in that jurisdiction. To the extent an implied warranty cannot be excluded, such warranty is limited in duration to the warranty period. The disclaimer to obtain warranty for support, please be prepared to provide the product The Customer will be expected to complete a “Return Material Authorization (RMA)” form to initiate the request. Full instructions as to how to complete and where to send the form are provided on the form. Date of proof of purchase from
Quantum 1000 Base Station User Products returned to PureWave Inc must be preAuthorization (RMA) number and sent Customer requesting the RMA will be the exporter. The exporter is responsible to ship RMA equipment to PureWave’s address and has to bear the cost and risk involved in bringing the goods to PureWavelocation. Risk of loss in return shipment will be borne by Customer, and it is recommended that returned goods be insured and/or sent by a method that provides for tracking of the package. Responsibility for loss or damage does not transfer to PureWavPureWave determines that the item is actually defective, the repaired or replaced item will be shipped to Customer, at PureWave's expense, (1) not later than thirty (30) days after PureWave rdefective product or (2) to the terms of a separate written agreement with PureWave. If the allegedly non-conforming Product is not received by PureWave within thirty (30) days of Customer initiating the RMA request, the RMA process for that RMA Status Customer may also obtain the status of its RMA request by sending an ereferencing Customer’s assigned RMA Number. Customer Obligations No product will be accepted for repair or replacement by PureWave without a RMA number. must be returned to PureWave, properly packaged to prevent damage, shipping and handling charges prepaid, with the RMA number prominently displayed on the outside ofdetermines that a returned product is not defective or is not covered by the terms of the warranty, the Customer will be charged a service charge and return shipping charges Out of Box Failure (OBF) / Dead on Arrival (DOA) In the event a product becomes entirely inoperable within the first fortyinstallation of the product, and such installation takes place within ninety (90) days after the date of shipment from PureWave, upon verification of theBox Failure (OBF) or “Dead on Arrival (DOA). A replacement shall be provided by advance replacement. The replacement product will be shipped within five (5) business days after PureWave's verificatDOA product, subject to availability and other shipping restrictions. The shipment of advance replacement products is subject to local legal requirements and may not be available in all locations. When an advance replacement is provided and Cuswithin fifteen (15) days after shipment of the replacement, PureWave will charge the Customer for the replacement product, at list price. Advance Replacement In some unique situations, PureWaveadvance replacement for a non-conforming Product during its warranty period. The following conditions apply to advance replacements: (i) PureWave has a suitable “equivalent” replacement unit(ii) Customer’s network is experiencing a severe degradation or a complete outage.(iii) Customer has complied with the RMA procedures provided herein Quantum 1000 Base Station User Guide Rev 1.1, Page Products returned to PureWave Inc must be pre-authorized by PureWave with a Return Material Authorization (RMA) number and sent prepaid and packaged appropriately for safe shipment. The he RMA will be the exporter. The exporter is responsible to ship RMA equipment to PureWave’s address and has to bear the cost and risk involved in bringing the goods to PureWaveRisk of loss in return shipment will be borne by Customer, and it is recommended that returned goods be insured and/or sent by a method that provides for tracking of the package. Responsibility for loss or damage does not transfer to PureWave until the returned item is received by PureWave. Provided that PureWave determines that the item is actually defective, the repaired or replaced item will be shipped to Customer, at PureWave's expense, (1) not later than thirty (30) days after PureWave receives the defective product or (2) to the terms of a separate written agreement with PureWave. conforming Product is not received by PureWave within thirty (30) days of Customer initiating the RMA request, the RMA process for that Product will be deemed cancelled. Customer may also obtain the status of its RMA request by sending an e-mail to rma@pwnets.comreferencing Customer’s assigned RMA Number. t will be accepted for repair or replacement by PureWave without a RMA number. must be returned to PureWave, properly packaged to prevent damage, shipping and handling charges the RMA number prominently displayed on the outside of the container. If PureWave determines that a returned product is not defective or is not covered by the terms of the warranty, the Customer will be charged a service charge and return shipping charges / Dead on Arrival (DOA) the event a product becomes entirely inoperable within the first forty-eight (48) hours of the initial installation of the product, and such installation takes place within ninety (90) days after the date of shipment from PureWave, upon verification of the condition by PureWave, it will be considered as an “Out Box Failure (OBF) or “Dead on Arrival (DOA). A replacement shall be provided by advance replacement. The replacement product will be shipped within five (5) business days after PureWave's verificatDOA product, subject to availability and other shipping restrictions. The shipment of advance replacement products is subject to local legal requirements and may not be available in all locations. When an advance replacement is provided and Customer fails to return the original product to PureWave within fifteen (15) days after shipment of the replacement, PureWave will charge the Customer for the In some unique situations, PureWave may consider, at its sole discretion on a case-by-case basis, an conforming Product during its warranty period. The following conditions apply to advance replacements: PureWave has a suitable “equivalent” replacement unit available Customer’s network is experiencing a severe degradation or a complete outage.Customer has complied with the RMA procedures provided herein Rev 1.1, Page 6 of 70 authorized by PureWave with a Return Material prepaid and packaged appropriately for safe shipment. The he RMA will be the exporter. The exporter is responsible to ship RMA equipment to PureWave’s address and has to bear the cost and risk involved in bringing the goods to PureWave’s Risk of loss in return shipment will be borne by Customer, and it is recommended that returned goods be insured and/or sent by a method that provides for tracking of the package. Responsibility for loss or e until the returned item is received by PureWave. Provided that PureWave determines that the item is actually defective, the repaired or replaced item will be shipped to eceives the conforming Product is not received by PureWave within thirty (30) days of Customer rma@pwnets.com and t will be accepted for repair or replacement by PureWave without a RMA number. The product must be returned to PureWave, properly packaged to prevent damage, shipping and handling charges If PureWave determines that a returned product is not defective or is not covered by the terms of the warranty, the eight (48) hours of the initial installation of the product, and such installation takes place within ninety (90) days after the date of condition by PureWave, it will be considered as an “Out Box Failure (OBF) or “Dead on Arrival (DOA). A replacement shall be provided by advance replacement. The replacement product will be shipped within five (5) business days after PureWave's verification of the DOA product, subject to availability and other shipping restrictions. The shipment of advance replacement tomer fails to return the original product to PureWave within fifteen (15) days after shipment of the replacement, PureWave will charge the Customer for the case basis, an Customer’s network is experiencing a severe degradation or a complete outage.
Quantum 1000 Base Station User (iv) Customer pays for all overPureWave and provides a credit card number and signed credit card authorization form to secure the transaction (or, upon PureWave’s approval, an Order may be used to secure the transaction and pay all associated charges)(v) When an advance replacement is provided andto PureWave within fifteen (15) days after shipment of the replacement, PureWave will charge the Customer for the replacement product, at list price. PureWave will use reasonable commercial efforts to ship business days after PureWave’s confirmation that advance replacement is appropriate. PureWave shall not be responsible for shipping delays if any of conditions herein are not met. Out of Warranty Repair of products that are out of warranty will be subject to a repair fee. PureWave does offer extended warranties and enhanced service options for its direct and indirect customers who desire those enhanced features. Please contact a PureWave Customer Service Cenyou would like more information about these options ASSISTANCE For assistance, contact your nearest PureWave Networks Sales and Service office.Additional information is available on the PureWave Networks w For Customer Service call: 650-528 Quantum 1000 Base Station User Guide Rev 1.1, Page Customer pays for all over-night shipping and handling charges for shipments to and from and provides a credit card number and signed credit card authorization form to secure the transaction (or, upon PureWave’s approval, an Order may be used to secure the transaction and pay all associated charges) When an advance replacement is provided and Customer fails to return the original product to PureWave within fifteen (15) days after shipment of the replacement, PureWave will charge the Customer for the replacement product, at list price. PureWave will use reasonable commercial efforts to ship advance replacement Products within five (5) business days after PureWave’s confirmation that advance replacement is appropriate. PureWave shall not be responsible for shipping delays if any of conditions herein are not met. products that are out of warranty will be subject to a repair fee. PureWave does offer extended warranties and enhanced service options for its direct and indirect customers who desire those enhanced features. Please contact a PureWave Customer Service Center either by telephone or via the Internet if you would like more information about these options For assistance, contact your nearest PureWave Networks Sales and Service office. Additional information is available on the PureWave Networks website at http://www.pwnets.com528-5200, or Email: support@pwnets.com. Rev 1.1, Page 7 of 70 night shipping and handling charges for shipments to and from and provides a credit card number and signed credit card authorization form to secure the transaction (or, upon PureWave’s approval, an Order may be used to secure the Customer fails to return the original product to PureWave within fifteen (15) days after shipment of the replacement, PureWave will advance replacement Products within five (5) business days after PureWave’s confirmation that advance replacement is appropriate. PureWave shall products that are out of warranty will be subject to a repair fee. PureWave does offer extended warranties and enhanced service options for its direct and indirect customers who desire those enhanced ter either by telephone or via the Internet if http://www.pwnets.com.
Quantum 1000 Base Station User When installing this equipment, observe the following precautions to minimize the danger of peinjury: Danger: • NEVER install equipment if there is a chance of lightning or other adverse weather conditions.• NEVER install in a wet location unless the equipment is specifically designed for wet locations.• NEVER touch uninsulated wires or terminals unless the wire has been disconnected at the Network interface. • ALWAYS use caution when installing or modifying cables. ESD Warning: • WARNING: Always assume that all components and assemblies are static sensitive and always follow local ESD-prevention guidelines to prevent equipment damage. EXTERNAL POWER – SOURCE: • WARNING: For any external power supply that provides the power source for the PureWave equipment, replace any power supply fuse with the same rating or equivalent, otherwise PureWave Networks will not be responsible for any subsequent damage to its equipment.• Use normal caution when installing or modifying cables. Dangerous voltages may be present. It is also considered imprudent to install during a lightning storm.• Always disconnect all lines and power connections before servicing or disassembling this equipment. • For performance and safety reasons, only power supplies listed for use with telephone equipment by a Nationally Recognized Testing Laboratory (NRTL) should be used wi• Refer to the installation section of the appropriate instruction manual for the unit you are installing for: o Cabling informationo Proper connectionso Grounding information• All wiring external to the product(s) should follow the provisions of thNational Electrical Code. WARNING: These units contain no user serviceable components. Only authorized Service Personnel should service or repair these units. "Use only isolated Class 2 Power Source, Rated 48V dc 5.0A Minimum." Quantum 1000 Base Station User Guide Rev 1.1, Page SAFETY PRECAUTIONS When installing this equipment, observe the following precautions to minimize the danger of peNEVER install equipment if there is a chance of lightning or other adverse weather conditions.NEVER install in a wet location unless the equipment is specifically designed for wet locations.wires or terminals unless the wire has been disconnected at the ALWAYS use caution when installing or modifying cables. WARNING: Always assume that all components and assemblies are static sensitive and always prevention guidelines to prevent equipment damage. WARNING: For any external power supply that provides the power source for the PureWave equipment, replace any power supply fuse with the same rating or equivalent, otherwise PureWave Networks will not be responsible for any subsequent damage to its equipment.Use normal caution when installing or modifying cables. Dangerous voltages may be present. It is also considered imprudent to install during a lightning storm. connect all lines and power connections before servicing or disassembling this For performance and safety reasons, only power supplies listed for use with telephone equipment by a Nationally Recognized Testing Laboratory (NRTL) should be used with equipment.Refer to the installation section of the appropriate instruction manual for the unit you are installing Cabling information Proper connections Grounding information All wiring external to the product(s) should follow the provisions of the current edition of the These units contain no user serviceable components. Only authorized Service Personnel should service or repair these units. "Use only isolated Class 2 Power Source, Rated 48V dc 5.0A Minimum." Rev 1.1, Page 8 of 70 When installing this equipment, observe the following precautions to minimize the danger of personnel NEVER install equipment if there is a chance of lightning or other adverse weather conditions. NEVER install in a wet location unless the equipment is specifically designed for wet locations. wires or terminals unless the wire has been disconnected at the WARNING: Always assume that all components and assemblies are static sensitive and always WARNING: For any external power supply that provides the power source for the PureWave equipment, replace any power supply fuse with the same rating or equivalent, otherwise PureWave Networks will not be responsible for any subsequent damage to its equipment. Use normal caution when installing or modifying cables. Dangerous voltages may be present. It is connect all lines and power connections before servicing or disassembling this For performance and safety reasons, only power supplies listed for use with telephone equipment th equipment. Refer to the installation section of the appropriate instruction manual for the unit you are installing e current edition of the These units contain no user serviceable components. Only authorized Service Personnel should service or repair these units. "Use only isolated Class 2 Power Source, Rated 48V dc 5.0A Minimum."
Quantum 1000 Base Station User 1. Introduction ................................1.1 Overview ................................1.2 System Components ................................1.3 Scope ................................2. Base Station ................................2.1 Overview ................................2.2 Hardware ................................2.3 MAC Software Architecture2.4 Enclosure ................................2.5 External Connections ................................2.6 Power ................................2.7 GPS ................................................................2.8 Antenna ................................2.8.1 Antenna Mounting Kit ................................2.9 Ethernet ................................2.9.1 Weather Protection of the Ethernet Connector3. Grounding and Lightning Requirements3.1 Lightning Protection Installation Components3.2 Lightning Rod ................................3.3 Down Conductor ................................3.4 Co-axial and/or Cat 5 Cable Shield Grounding3.5 Grounding and Bonding ................................3.6 Recommended Connection of a Bonded Ground3.7 Single Point Grounding Concept3.8 Lightning and Surge Protection4. Weather Protection ................................4.1 Weather Sealing ................................4.2 Anti-Seize ................................5. Base Station Bring-up ................................5.1 Overview ................................5.2 Connect to the Base Station5.3 Configure the Base Station Quantum 1000 Base Station User Guide Rev 1.1, Page TABLE OF CONTENTS ................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................MAC Software Architecture ................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................Weather Protection of the Ethernet Connector ................................................................Grounding and Lightning Requirements ............................................................Lightning Protection Installation Components ..............................................................................................................................................................................................................................................................................................axial and/or Cat 5 Cable Shield Grounding ................................................................................................................................................................Recommended Connection of a Bonded Ground ................................................................Single Point Grounding Concept ................................................................................................Lightning and Surge Protection ....................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................Connect to the Base Station ................................................................................................Configure the Base Station ................................................................................................ Rev 1.1, Page 9 of 70 ........................................... 10 ..................................... 10 ................................................... 11 .......................................... 12 .......................................... 13 ..................................... 13 ..................................... 14 ......................................... 15 .................................... 16 .................................................. 18 .......................................... 20 ............................................. 23 ....................................... 24 .............................................. 26 ....................................... 32 ....................................... 34 ............................ 38 ............................................. 38 .............................. 39 ......................................................... 40 ........................................... 40 .............................................. 40 ....................................... 40 ................................. 41 ................................... 42 ............................... 46 .......................... 46 .................................... 49 ........................... 51 ..................................... 51 ....................................... 51 ......................................... 52
Quantum 1000 Base Station User 1. Introduction 1.1 Overview PureWave Networks develops carrierPureWave’s use of advanced multi-delivery of quadruple-play services (voice, video, data, and mobility) tCable services. This equipment is the most spectrallymetropolitan-area-networking equipment in its class available in the world today. The PureWave solution consists of four • PureWave Quantum 1000 Base Station Sector (BSS)• Subscriber customer premises equipment (CPE)• Quad Antenna panel • Element management system (EMS). The Architecture Reference Model is shown in figure 1. The Base Station Sector supports the wtransfer of IP (Internet Protocol) packet data and communicates wirelessly to customer premise equipment (CPE) terminals. The interface to the ASNIETF RFCs, and Ethernet standards. The Element Managemcommissioning and network performance and characterization The Quantum 1000 Base Station provides standard WiMax smart antenna support:• AAS processing (beam forming and null steering)• AMC-like subchannel assignments The system uses advanced technology to realize exceptional performance gains:• Fast transmit/receive compensation necessary for channel reciprocity for mobility,• Complexity-reducing algorithms that allow more than 2 antennas per sector,• Processing algorithms that virtually eliminate interference instead of beam steering algorithms that provide limited benefits and do not scale to multi• Flexibility to grow coverage by adding sectors in a compact and modular fashion. A Quantum 1000 Base Station Sector provides 8 times the spectral efficiency and significant link gain relative to standard WiMax Wave-2 solutions. The benefits are: • High capacity deployments using fewer channels, • Reduced or no cell planning, • Fewer base stations are needed to cover a region, and • Improved user performance. The base station is highly modular. The key compprocessing cards, and RF modules for interfacing to available frequency bands. The Baconnects to multiple single-antenna units or a multi Quantum 1000 Base Station User Guide Rev 1.1, Page PureWave Networks develops carrier-class WiMAX 802.16e compliant Base Station equipment. -antenna technologies with software radio architecture enables play services (voice, video, data, and mobility) that are competitive with DSL and Cable services. This equipment is the most spectrally-efficient, range-extending, wireless broadband networking equipment in its class available in the world today. The PureWave solution consists of four major elements: PureWave Quantum 1000 Base Station Sector (BSS) Subscriber customer premises equipment (CPE) Element management system (EMS). The Architecture Reference Model is shown in figure 1. The Base Station Sector supports the wtransfer of IP (Internet Protocol) packet data and communicates wirelessly to customer premise equipment (CPE) terminals. The interface to the ASN-GW (access service network gateway) adheres to IETF RFCs, and Ethernet standards. The Element Management System (EMS) supports operations, commissioning and network performance and characterization functions. The Quantum 1000 Base Station provides standard WiMax smart antenna support: AAS processing (beam forming and null steering) assignments The system uses advanced technology to realize exceptional performance gains: Fast transmit/receive compensation necessary for channel reciprocity for mobility,reducing algorithms that allow more than 2 antennas per sector, sing algorithms that virtually eliminate interference instead of beam steering algorithms that provide limited benefits and do not scale to multi-cell deployments, and Flexibility to grow coverage by adding sectors in a compact and modular fashion.tum 1000 Base Station Sector provides 8 times the spectral efficiency and significant link gain 2 solutions. High capacity deployments using fewer channels, Reduced or no cell planning, ions are needed to cover a region, and Improved user performance. The base station is highly modular. The key components are power units, Linux processing card, networkprocessing cards, and RF modules for interfacing to available frequency bands. The Baantenna units or a multi-antenna radome. Rev 1.1, Page 10 of 70 class WiMAX 802.16e compliant Base Station equipment. antenna technologies with software radio architecture enables hat are competitive with DSL and extending, wireless broadband The Architecture Reference Model is shown in figure 1. The Base Station Sector supports the wireless transfer of IP (Internet Protocol) packet data and communicates wirelessly to customer premise GW (access service network gateway) adheres to ent System (EMS) supports operations, Fast transmit/receive compensation necessary for channel reciprocity for mobility, sing algorithms that virtually eliminate interference instead of beam steering algorithms Flexibility to grow coverage by adding sectors in a compact and modular fashion. tum 1000 Base Station Sector provides 8 times the spectral efficiency and significant link gain onents are power units, Linux processing card, network processing cards, and RF modules for interfacing to available frequency bands. The Base Station
Quantum 1000 Base Station User Figure 1 The base station is highly modular. The key components are power units, baseband processing cards, and RF modules for interfacing to available frequency bands. The Base Station Sector connects to multiple single-antenna units or a multi 1.2 System Components The PureWave System is composed of a Base Station Sector (which is itself connected to an antenna or antenna array) and subscriber stations (also known as customer premises equipment (CPE)), which connect to each other through an air intStation connect to their customer or provider networks, also known as backhaul networks, via a provider interface, whereas CPE connect to their subscriber or user networks through a subscri Base Station have hardware, software, and mechanical characteristics that support their functional and performance requirements. Base Station and CPEs interconnect with each other and their respective networks via sets of network, MAC, and Quantum 1000 Base Station User Guide Rev 1.1, Page Figure 1 - Architecture Reference Model. The base station is highly modular. The key components are power units, baseband processing cards, and RF modules for interfacing to available frequency bands. The Base Station Sector connects to antenna units or a multi-antenna radome. The PureWave System is composed of a Base Station Sector (which is itself connected to an antenna or antenna array) and subscriber stations (also known as customer premises equipment (CPE)), which connect to each other through an air interface (airlink) and to their respective networks (figure 2). Base Station connect to their customer or provider networks, also known as backhaul networks, via a provider interface, whereas CPE connect to their subscriber or user networks through a subscriber interface.Base Station have hardware, software, and mechanical characteristics that support their functional and performance requirements. Base Station and CPEs interconnect with each other and their respective networks via sets of network, MAC, and PHY protocols. Rev 1.1, Page 11 of 70 The base station is highly modular. The key components are power units, baseband processing cards, and RF modules for interfacing to available frequency bands. The Base Station Sector connects to The PureWave System is composed of a Base Station Sector (which is itself connected to an antenna or antenna array) and subscriber stations (also known as customer premises equipment (CPE)), which erface (airlink) and to their respective networks (figure 2). Base Station connect to their customer or provider networks, also known as backhaul networks, via a provider ber interface. Base Station have hardware, software, and mechanical characteristics that support their functional and performance requirements. Base Station and CPEs interconnect with each other and their respective
Quantum 1000 Base Station User Provider(aka Customer)Provider Interface(Backhaul)Base Station SectorHWNetworkMACPHYLayers/ProtocolsFigure 1.3 Scope This document is intended to be used by wireless broadband installation engineers. It contains information needed to install and connect a Quantum 1000 Base The Quantum 1000 Base Station Sector is designed to be “plugNetworks; however, guidance is given as to how to assess general system integrity and operational readiness upon initial power-up. Quantum 1000 Base Station User Guide Rev 1.1, Page Base Station CPESubscriber InterfaceBase Station SectorAir Interface(Airlink)Subscriber Station(CPE)HWSWMechanicalFigure 2 - General View of System Components This document is intended to be used by wireless broadband installation engineers. It contains information needed to install and connect a Quantum 1000 Base Station and Antenna Assembly1000 Base Station Sector is designed to be “plug-and-play” direct from PureWave Networks; however, guidance is given as to how to assess general system integrity and operational Rev 1.1, Page 12 of 70 Subscriber InterfaceSubscriber(aka User) This document is intended to be used by wireless broadband installation engineers. It contains Station and Antenna Assembly play” direct from PureWave Networks; however, guidance is given as to how to assess general system integrity and operational
Quantum 1000 Base Station User 2. Base Station 2.1 Overview The Quantum 1000 employs an extremely flexible and versatile hardware architecture.base station is a sophisticated and highly integrated ASIC that combines 6 DSP and general purpose processor cores along with specialized DSP hardware.SNMP and other management functions.associated PAs, and 4 RF receivers (refer to figure 3). Important characteristics of the Quantum 1000 • Board-to-board communications for scaling up to 16 antennas.• 10 MHz profile • WiMAX OFDMA compliance • All layers implemented in software.• 2.3 – 2.7 GHz and 3.3 – 3.7 GHz operations. PureWave has implemented a scalable Stations by: • Adding more Base Station Sector to a location• Adding antennas (and corresponding RF module sets) within a sector• Adding processing capability in order to process traffic within additional spectrum • Upgrading software to allow for changes in features and standards. Figure Quantum 1000 Base Station User Guide Rev 1.1, Page extremely flexible and versatile hardware architecture.base station is a sophisticated and highly integrated ASIC that combines 6 DSP and general purpose cialized DSP hardware. A Linux-based subsystem supports applications, and other management functions. Finally,,the Quantum 1000 includes 2 RF transmitters and ociated PAs, and 4 RF receivers (refer to figure 3). Quantum 1000 Base Station Sector are: board communications for scaling up to 16 antennas. WiMAX OFDMA compliance All layers implemented in software. 3.7 GHz operations. PureWave has implemented a scalable architecture that lets service providers upgrade their Base Adding more Base Station Sector to a location Adding antennas (and corresponding RF module sets) within a sector Adding processing capability in order to process traffic within additional spectrum Upgrading software to allow for changes in features and standards. Figure 3 - Base Station Functional Components Rev 1.1, Page 13 of 70 extremely flexible and versatile hardware architecture. The heart of the base station is a sophisticated and highly integrated ASIC that combines 6 DSP and general purpose based subsystem supports applications, ,the Quantum 1000 includes 2 RF transmitters and architecture that lets service providers upgrade their Base Adding processing capability in order to process traffic within additional spectrum
Quantum 1000 Base Station User 2.2 Hardware This section describes the hardware characteristics for a shows the block diagram for the Base Station digital section. FPGARF IFRF IFRF IFRF IFReference ClockRF IFRF IFRF IFFigure Quantum 1000 Base Station User Guide Rev 1.1, Page ribes the hardware characteristics for a Quantum 1000 Base Station Sector. Figure 4 shows the block diagram for the Base Station digital section. Ethernet DSP 1DDR FlashDSP 2DDR FlashDSP DDRDSP 4DDR FlashDSP DDRFPGAFigure 4 - Base Station Digital Block Diagram Rev 1.1, Page 14 of 70 Base Station Sector. Figure 4 DSP 3FlashDSP 5Flash
Quantum 1000 Base Station User 2.3 MAC Software ArchitectureThis section describes the high level software Figure 5 shows the block diagram for Linux SBCPowerQuicc IIBackhaulCPUCOREUART 2ConsoleUART 0LinuxIntra-MgmtBS-Mgmt(External /Opt. Data)BS DaisychainStatus/EMSQuiccEngineEth-2Eth-0Figure The PureWave Quantum is an 802.16ecomprising the Network and Management processor (sometimes referred to as “the PowerQuicc or “the Linux”), and the other comprising the baseband PHY and MACthe system Manager and the baseband SoC (sometimes called the “Modem” or the “Modem”) is essentially a high-powered signal processor. See Figure The Network Processor is based on a Freescale PowerQuicc II, which cplus a “Quicc” engine for packet processing. The PowerPC runs Linux and hosts many highly complex applications including an SNMP device management agent, multiple databases, web server, CLI, logging and other system services. The other SoC is a WiMAX baseband processor. It contains three ARM9 cores, four general Tensilica cores and a fifth tensilicaprocessing, MAC and PHY tasks. The ARMs run the ThreadX operating system; the othhave a traditional RTOS. The Network Processor connects to the external backhaul through a pair of gigabit Ethernet ports, and to the Modem through two 100/1000MB management/control messages. Various protocols carried over the two Ethernets link the applications, including TCP/IP, UDP and custom Ethernet frames. Quantum 1000 Base Station User Guide Rev 1.1, Page Architecture s section describes the high level software characteristics for a Quantum 1000 Base Station.shows the block diagram for the Base Station software architecture. Modem EVKMACRF Tx RF RxBackhaulPHYPureWave Quantum 1000BASE STATIONSERIALSERIALIntra-MgmtData+R6 Ctrl + GRE DataReset (GPIO)/Control 1PPS SyncASN GatewayQuiccEngineGPS ModuleEth-1Eth-3Figure 5 – High Level SW Architecture n 802.16e WiMAX base station. It contains two major silicon devices, one comprising the Network and Management processor (sometimes referred to as “the PowerQuicc or “the Linux”), and the other comprising the baseband PHY and MAC processors. The Network Processor is the system Manager and the baseband SoC (sometimes called the “Modem” or the “Modem”) is d signal processor. See Figure 3. The Network Processor is based on a Freescale PowerQuicc II, which contains a standard PowerPC core plus a “Quicc” engine for packet processing. The PowerPC runs Linux and hosts many highly complex applications including an SNMP device management agent, multiple databases, web server, CLI, logging . The other SoC is a WiMAX baseband processor. It contains three ARM9 cores, four general Tensilica cores and a fifth tensilica-based DSP core. Together these perform network processing, MAC and PHY tasks. The ARMs run the ThreadX operating system; the othThe Network Processor connects to the external backhaul through a pair of gigabit Ethernet ports, and to MB Gigabit Ethernet ports. These ports carry a mix of traffic and ntrol messages. Various protocols carried over the two Ethernets link the applications, including TCP/IP, UDP and custom Ethernet frames. Rev 1.1, Page 15 of 70 Base Station. Modem EVKSoC WiMAX base station. It contains two major silicon devices, one comprising the Network and Management processor (sometimes referred to as “the PowerQuicc or “the processors. The Network Processor is the system Manager and the baseband SoC (sometimes called the “Modem” or the “Modem”) is ontains a standard PowerPC core plus a “Quicc” engine for packet processing. The PowerPC runs Linux and hosts many highly complex applications including an SNMP device management agent, multiple databases, web server, CLI, logging . The other SoC is a WiMAX baseband processor. It contains three ARM9 based DSP core. Together these perform network processing, MAC and PHY tasks. The ARMs run the ThreadX operating system; the other cores do not The Network Processor connects to the external backhaul through a pair of gigabit Ethernet ports, and to Ethernet ports. These ports carry a mix of traffic and ntrol messages. Various protocols carried over the two Ethernets link the applications,
Quantum 1000 Base Station User 2.4 Enclosure The Quantum 1000 Base Station Sector is made up of a single, weatherdimensions of: 24” W x 17” H x 5” D (figures near a corner of the rear of the enclosure. Each “ear” are spaced 37cm apart (center-to-center), horizontally, and Figure Figure 7 - Pole Mounted Quantum 1000 Base Station Sector Quantum 1000 Base Station User Guide Rev 1.1, Page Base Station Sector is made up of a single, weather-resistant cabinet with the overall ” H x 5” D (figures 6 and 7). The unit has 4 mounting “ears”, each one located near a corner of the rear of the enclosure. Each “ear” will accommodate a M10 bolt. The mounting holes center), horizontally, and 44.3cm apart, vertically (figure Figure 6 – Quantum 1000 Base Station Sector Pole Mounted Quantum 1000 Base Station Sector Rev 1.1, Page 16 of 70 resistant cabinet with the overall ). The unit has 4 mounting “ears”, each one located The mounting holes apart, vertically (figures 8 and 9).
Quantum 1000 Base Station User Figure 8 - Quantum 1000 Figure 9 – Quantum 1000 The Base Station unit can be installed either as an entire outdoor unit (ODU) or as an entire indoor unit (IDU). The antenna must always be installed outdoors. Note: It is recommended that the Base Station Enclosure is mounted upright such that the antenna N-type connectors face down towards the ground. air flow around the Base Station heatsinks (refer to figure Quantum 1000 Base Station User Guide Rev 1.1, Page Quantum 1000 Base Station Sector Rear View 37cm44.3cm Quantum 1000 Base Station Mounting Hole Pattern The Base Station unit can be installed either as an entire outdoor unit (ODU) or as an entire indoor unit (IDU). The antenna must always be installed outdoors. It is recommended that the Base Station Enclosure is mounted upright such that the type connectors face down towards the ground. Please ensure that there is adequate air flow around the Base Station heatsinks (refer to figure 8). Rev 1.1, Page 17 of 70 The Base Station unit can be installed either as an entire outdoor unit (ODU) or as an entire indoor unit It is recommended that the Base Station Enclosure is mounted upright such that the there is adequate
Quantum 1000 Base Station User Table 1 lists the mechanical, electrical and environmental properties of Quantum 1000 Physical & EnvironmentalDimensions Weight Power Temperature Humidity Surge ProtectionLightning ProtectionWeatherproofing Table 2.5 External Connections There are basically 4 types of connections that need to be made to the Base Station unit (see figures and 11). POWERGNDFigure 10 Quantum 1000 Base Station User Guide Rev 1.1, Page mechanical, electrical and environmental properties of Quantum 1000 Base StPhysical & Environmental Specifications 24.6” (H) x 17.4” (W) x 4.5” (D)23 pounds -48V DC, 65 Watts -33 to +55 degrees C 5 to 95% non-condensing Surge Protection UL497B Lightning Protection 10kA IEC 6100-4-5 (optional via external kit)Weatherproofing IP67 Table 1 – Physical and Environmental Properties External Connections There are basically 4 types of connections that need to be made to the Base Station unit (see figures Antenna SectionANT 1ANT 2ANT 3ANT 4 RS232 E-NET 1 E-GPS ANT 10 - Base Station Connections (Bottom View) Rev 1.1, Page 18 of 70 Base Station: 4.5” (D) 5 (optional via external kit) There are basically 4 types of connections that need to be made to the Base Station unit (see figures 10 -NET 2GPS ANT
Quantum 1000 Base Station User Figure Once the Base Station enclosure has been mounted, the following connections must be made. • POWER: Provides the DC power source for • GND: This provides a ground connection point for the Base Station. It is important to ensure that the Base Station is professionally grounded and complies with all local relevant grounding electrical codes. • GPS ANT: This port provides the connection between the GPS antenna (external) and the GPS receiver module (internal). GPS is used by the Base Station Sector to synchronize its TDD gate to those of Base Stations in neighboring cells. • ANT 1 – ANT 4: This is where the Base Statioantenna ports are described as: o ANT 1: This is a transmit (Tx) and a receive (Rx) port. o ANT 2: This is a transmit (Tx) and a receive (Rx) port.o ANT 3: This is a receive (Rx) port only.o ANT 4: This is a recei • RS232: This is the serial interface to the Base Station. This interface will be primarily used for “out of the box” configuration and debug purposes when directed by PureWave Technical Support Engineers. • E-NET 1: This Gigabit Ethernet connected to the Service Provider’s network equipment.the Base Station. Quantum 1000 Base Station User Guide Rev 1.1, Page Figure 11 - Base Station Connected Once the Base Station enclosure has been mounted, the following connections must be made. : Provides the DC power source for the Base Station unit. GND: This provides a ground connection point for the Base Station. It is important to ensure that the Base Station is professionally grounded and complies with all local relevant grounding ides the connection between the GPS antenna (external) and the GPS receiver module (internal). GPS is used by the Base Station Sector to synchronize its TDD gate to those of Base Stations in neighboring cells. This is where the Base Station is physically connected to an antenna.antenna ports are described as: ANT 1: This is a transmit (Tx) and a receive (Rx) port. ANT 2: This is a transmit (Tx) and a receive (Rx) port. ANT 3: This is a receive (Rx) port only. ANT 4: This is a receive (Rx) port only. RS232: This is the serial interface to the Base Station. This interface will be primarily used for “out of the box” configuration and debug purposes when directed by PureWave Technical Gigabit Ethernet port provides the data traffic backhaul interface that should be connected to the Service Provider’s network equipment. This port allows in-band management Rev 1.1, Page 19 of 70 Once the Base Station enclosure has been mounted, the following connections must be made. GND: This provides a ground connection point for the Base Station. It is important to ensure that the Base Station is professionally grounded and complies with all local relevant grounding ides the connection between the GPS antenna (external) and the GPS receiver module (internal). GPS is used by the Base Station Sector to synchronize its TDD gate n is physically connected to an antenna. The 4 RS232: This is the serial interface to the Base Station. This interface will be primarily used for “out of the box” configuration and debug purposes when directed by PureWave Technical port provides the data traffic backhaul interface that should be band management of
Quantum 1000 Base Station User • E-NET 2: This Gigabit Ethernet port provides an outthis port can be used for daisy device such as a web Cameraaggregated and passed through the backhauling connector NOTE: DO NOT POWER ON THE BASE STATION OR REMOTWO TRANSMITTING ANTENNA PORTS (ANT 1 ANSUITABLE RF LOAD OR AN ANTENNA. A FAILURRESULT IN INTERNAL DAMAGE TO THE BA Figure Connect the two transmitting ports (ANT 1 and ANT 2) to the two outer most elements of the actual antenna thus ensuring that the transmission paths are as far apart as possible on the 4 available antenna ports. It is also important that while the base santenna ports remain terminated. Removal of the transmitter load while operating at high output powers is not recommended and may result in damage to the base station. 2.6 Power The Base Station DC power requirements is such that the external DC source needs to be capable of delivering up to 4 Amps of current at 48VDC. PureWave provides the power connector to the Base SInstallation kit (figure 13). The "Tyco" power connector that is used on the Base Station will Remember to take account of the voltage drop when running long power cable runs. AWG, for a cable length of 100 feet, a nominal 48VDC supply delivering into a voltage drop of 2.7 volts. Please ensure that the DC power source is powered off and solder the and 2. Solder the 48 VDC Return wires to pins Quantum 1000 Base Station User Guide Rev 1.1, Page NET 2: This Gigabit Ethernet port provides an out-of-band management interfaisy chaining to another base station or to connect to an external device such as a web Camera. The traffic coming from the daisy chain connector shall be aggregated and passed through the backhauling connector. BASE STATION OR REMOVE THE BASE STATION POWER UNLESS THE ENNA PORTS (ANT 1 AND ANT 2) ARE EITHER TERMINATED BY A AN ANTENNA. A FAILURE TO ENSURE THIS, AT ALL TIMES, COULD NAL DAMAGE TO THE BASE STATION (FIGURE 12). Figure 12 - Base Station Connected Connect the two transmitting ports (ANT 1 and ANT 2) to the two outer most elements of the actual antenna thus ensuring that the transmission paths are as far apart as possible on the 4 available antenna It is also important that while the base station is operating at maximum power levels, the transmitting antenna ports remain terminated. Removal of the transmitter load while operating at high output powers is not recommended and may result in damage to the base station. The Base Station DC power requirements is such that the external DC source needs to be capable of Amps of current at -48 VDC. The Base Station nominally runs at approx 2 Amps at PureWave provides the power connector to the Base Station (Tyco P/N 796094" power connector that is used on the Base Station will accommodate 14 to 18Remember to take account of the voltage drop when running long power cable runs. For 00 feet, a nominal 48VDC supply delivering into a 2A load will lead to a Please ensure that the DC power source is powered off and solder the -48 VDC wires to connector pins 1 Solder the 48 VDC Return wires to pins 3 and 4 (figures 14 to 16). Rev 1.1, Page 20 of 70 band management interface. In addition, to another base station or to connect to an external he traffic coming from the daisy chain connector shall be POWER UNLESS THE TERMINATED BY A ALL TIMES, COULD Connect the two transmitting ports (ANT 1 and ANT 2) to the two outer most elements of the actual antenna thus ensuring that the transmission paths are as far apart as possible on the 4 available antenna tation is operating at maximum power levels, the transmitting antenna ports remain terminated. Removal of the transmitter load while operating at high output powers is The Base Station DC power requirements is such that the external DC source needs to be capable of The Base Station nominally runs at approx 2 Amps at -796094-2) as part of the 18 gauge wire. For example, for 18 A load will lead to a 48 VDC wires to connector pins 1
Quantum 1000 Base Station User Figure 13 - Base Station Power Input Connector (Conxall P/N 4280 Figure Figure Quantum 1000 Base Station User Guide Rev 1.1, Page Base Station Power Input Connector (Conxall P/N 4280-5PG- 14 - Base Station Power Input Connector 15 - Base Station Power Input Connector Rev 1.1, Page 21 of 70 -300)
Quantum 1000 Base Station User Figure The following table 2 indicates the connector pin Figure 17 is an expanded view of the connector onto which is attached the actual cable of wires. Figure 17 - Base Station Power Input Cable Connector Expanded View Quantum 1000 Base Station User Guide Rev 1.1, Page 16 - Base Station Power Input Connector The following table 2 indicates the connector pin-outs. Pin # Signal 1 -48V DC 2 -48V DC 3 48v DC Return 4 48v DC Return Table 2 – Power Pin-out connections is an expanded view of the connector onto which is attached the actual cable of wires. Base Station Power Input Cable Connector Expanded View Rev 1.1, Page 22 of 70 is an expanded view of the connector onto which is attached the actual cable of wires. Base Station Power Input Cable Connector Expanded View
Quantum 1000 Base Station User 2.7 GPS This port provides the connection between the GPS antenna (external) and the GPS receiver (internal). GPS is used by the Base Station to synchronize its TDD gate to those of Base Stations in neighboring cells. Connect the coaxial cable from the external GPS antenna to the SMAconnector marked “GPS” on the bottom right corner GPS antennas are shown in figure 1 Figure 18 - Base Station Underside View of GPS Antenna Connection Figure 19 - Typical Quantum 1000 Base Station User Guide Rev 1.1, Page This port provides the connection between the GPS antenna (external) and the GPS receiver (internal). GPS is used by the Base Station to synchronize its TDD gate to those of Base Stations in neighboring cells. Connect the coaxial cable from the external GPS antenna to the SMAconnector marked “GPS” on the bottom right corner of the Base Station unit (refer to figure 1GPS antennas are shown in figure 19. Base Station Underside View of GPS Antenna Connection Typical Base Station Sector External GPS Antenna’s Rev 1.1, Page 23 of 70 This port provides the connection between the GPS antenna (external) and the GPS receiver module (internal). GPS is used by the Base Station to synchronize its TDD gate to those of Base Stations in neighboring cells. Connect the coaxial cable from the external GPS antenna to the SMA-type female of the Base Station unit (refer to figure 18). Typical Base Station Underside View of GPS Antenna Connection
Quantum 1000 Base Station User No software pre-configuration is required and all that is needed is to connect the Base Station to a GPS. When the Base Station detects that a 1 pps GPS signal is present then it will synchronize its TDD gate to the GPS and if it does not detect a 1 pps GPS signal then it will s In the event that there are co-located multiple Base Stations, it is important to synchronize all the Base Station to a 1 pps GPS such that this will coconcurrently. This is especially important if neighboring Base Stations are set to operate on overlapping or identical frequency channels. 2.8 Antenna A low-loss, coaxial cable has to be connected to each of the Nback of the antenna panel and the respective antenna port on the base of the Base Station Sector. The co-axial cable must be capable of propagating the relrecommended to use any high-performance, lowTechnologies P/N CA3N100 or Times Microwave LMR 400).The order of antenna connections is unimportant. The important consideration is the length of the coand thus effective range of the system. In the case that the Base Station unit is installed outdoors and close to the antenna, then the co-axial cable runs can be kept Base Station unit is installed indoors with long cable runs up the tower to the antennas then the amount of signal loss will need to be calculated to ensure that adequate range will still be achieved. As an example,a Times Microwave LMR400 cable has an attenuation loss of 6.8dB per 100 feet at a frequency of 2.5GHz. For your information, the procedure to install co Note: It is strongly recommended that appropriate lightninstalled (refer to section 3). Please ensure that appropriate weather protection is applied to all outdoor N-type coaxial connections. One antenna panel is used for each Base Station. The antenna panel is populated with a number of directional patch-element strips. All elements are enclosed within a single radome and common, rear mounting plate. Access to each element (antenna) is provideconnector. Thus, for a 4-element antenna panel configuration there are a total of 4 exposed RF connectors protruding from the rear mounting plate (refer to figures The specifications for the 2.5GHz and the 3.65GHz antenna’s are detailed in Appendix A. Quantum 1000 Base Station User Guide Rev 1.1, Page ration is required and all that is needed is to connect the Base Station to a GPS. When the Base Station detects that a 1 pps GPS signal is present then it will synchronize its TDD gate to the GPS and if it does not detect a 1 pps GPS signal then it will synchronize to its own internal source.located multiple Base Stations, it is important to synchronize all the Base Station to a 1 pps GPS such that this will co-ordinate all Base Station to transmit and receive This is especially important if neighboring Base Stations are set to operate on overlapping loss, coaxial cable has to be connected to each of the N-type female connectors located on the back of the antenna panel and the respective antenna port on the base of the Base Station Sector. The axial cable must be capable of propagating the relevant RF frequency and therefore it is performance, low-loss 400-series coaxial cable (i.e. Hyperlink Technologies P/N CA3N100 or Times Microwave LMR 400).The order of antenna connections is ation is the length of the co-axial cable as this will affect the amount of signal loss and thus effective range of the system. In the case that the Base Station unit is installed outdoors and axial cable runs can be kept short and thus loss is minimized. If the Base Station unit is installed indoors with long cable runs up the tower to the antennas then the amount of signal loss will need to be calculated to ensure that adequate range will still be achieved. As an example,a Times Microwave LMR400 cable has an attenuation loss of 6.8dB per 100 feet at a frequency of For your information, the procedure to install co-axial connectors is provided in Appendix A.It is strongly recommended that appropriate lightning surge protection devices are Please ensure that appropriate weather protection is applied to all type coaxial connections. One antenna panel is used for each Base Station. The antenna panel is populated with a number of element strips. All elements are enclosed within a single radome and common, rear mounting plate. Access to each element (antenna) is provided by a dedicated N-type female coaxial RF element antenna panel configuration there are a total of 4 exposed RF connectors protruding from the rear mounting plate (refer to figures 20 and 21). nd the 3.65GHz antenna’s are detailed in Appendix A. Rev 1.1, Page 24 of 70 ration is required and all that is needed is to connect the Base Station to a GPS. When the Base Station detects that a 1 pps GPS signal is present then it will synchronize its TDD gate to ynchronize to its own internal source. located multiple Base Stations, it is important to synchronize all the Base ordinate all Base Station to transmit and receive This is especially important if neighboring Base Stations are set to operate on overlapping type female connectors located on the back of the antenna panel and the respective antenna port on the base of the Base Station Sector. The evant RF frequency and therefore it is series coaxial cable (i.e. Hyperlink Technologies P/N CA3N100 or Times Microwave LMR 400).The order of antenna connections is axial cable as this will affect the amount of signal loss and thus effective range of the system. In the case that the Base Station unit is installed outdoors and short and thus loss is minimized. If the Base Station unit is installed indoors with long cable runs up the tower to the antennas then the amount of signal loss will need to be calculated to ensure that adequate range will still be achieved. As an example, a Times Microwave LMR400 cable has an attenuation loss of 6.8dB per 100 feet at a frequency of axial connectors is provided in Appendix A. ing surge protection devices are Please ensure that appropriate weather protection is applied to all One antenna panel is used for each Base Station. The antenna panel is populated with a number of element strips. All elements are enclosed within a single radome and common, rear type female coaxial RF element antenna panel configuration there are a total of 4 exposed RF nd the 3.65GHz antenna’s are detailed in Appendix A.
Quantum 1000 Base Station User Figure The antenna panel will be mounted to a pole having an outer diameter (OD) between provided mounting kit. Quantum 1000 Base Station User Guide Rev 1.1, Page Figure 20 - Base Station Antenna Figure 21 – Typical Antenna Deployment The antenna panel will be mounted to a pole having an outer diameter (OD) between 1” and Rev 1.1, Page 25 of 70 ” and 4”, via the
Quantum 1000 Base Station User 2.8.1 Antenna Mounting Kit The procedure to install the antenna mounting kit is detailed below. It is recommended that that mounting kit is attached to the antenna prior to hoisting up the tower. Figure 22 is an illustration of the components that are included in the antenna mounting kit. 1) Lay down the antenna, designating which way is “up” (figure 2 Quantum 1000 Base Station User Guide Rev 1.1, Page Antenna Mounting Kit The procedure to install the antenna mounting kit is detailed below. It is recommended that that mounting kit is attached to the antenna prior to hoisting up the tower. is an illustration of the components that are included in the antenna mounting kit. Figure 22 – Antenna Mounting Kit Lay down the antenna, designating which way is “up” (figure 23). Figure 23 – Rear Antenna Face Rev 1.1, Page 26 of 70 The procedure to install the antenna mounting kit is detailed below. It is recommended that that mounting is an illustration of the components that are included in the antenna mounting kit.
Quantum 1000 Base Station User 2) Take the large U-bracket with the slot is pointed towards the bottom of the antenna. This is to allow for the angular displacement. 3) Tighten and secure the U-Brackets using Quantum 1000 Base Station User Guide Rev 1.1, Page bracket with the cut-out clot and insert over the 4 bolts (figure 2the slot is pointed towards the bottom of the antenna. This is to allow for the angular Figure 24 – Attached U-brackets Brackets using the appropriate nut (figure 25) Figure 25 – Secure U-brackets Rev 1.1, Page 27 of 70 out clot and insert over the 4 bolts (figure 24). Ensure that the slot is pointed towards the bottom of the antenna. This is to allow for the angular
Quantum 1000 Base Station User 4) Take the pole clamp section with the bolt hole and secure to the Uwasher (figure 26). Secure a pole clamp section to each U Figure 5) Depending on the intended angle of elevation and degree of down/up tilt will determine whether to lock one end and have flexibility on the other. This is the intent of the slots. Figure 2downtilting antenna and therefore the upper bracket. Figure Quantum 1000 Base Station User Guide Rev 1.1, Page Take the pole clamp section with the bolt hole and secure to the U-Bracket using the bolt and lock ). Secure a pole clamp section to each U-Bracket. Figure 26 – Pole Clamp half section Depending on the intended angle of elevation and degree of down/up tilt will determine whether to lock one end and have flexibility on the other. This is the intent of the slots. Figure 2downtilting antenna and therefore the bottom bracket is ”fixed” and movement is allowed in the Figure 27 – Pole Clamp to U-bracket Rev 1.1, Page 28 of 70 Bracket using the bolt and lock Depending on the intended angle of elevation and degree of down/up tilt will determine whether to lock one end and have flexibility on the other. This is the intent of the slots. Figure 27 is for a bottom bracket is ”fixed” and movement is allowed in the
Quantum 1000 Base Station User 6) The other half of the pole clamp section can now be attached using the M4 by 25 bolts plus the lock washer and lock nut (figure 2depending on the thickness of the pole (figure 2 Figure Figure Quantum 1000 Base Station User Guide Rev 1.1, Page The other half of the pole clamp section can now be attached using the M4 by 25 bolts plus the lock washer and lock nut (figure 28). These will be adjusted to provide the necessary clamp depending on the thickness of the pole (figure 29). Figure 28 – Pole Clamp half section Figure 29 - Mounting Kit final assembly Rev 1.1, Page 29 of 70 The other half of the pole clamp section can now be attached using the M4 by 25 bolts plus the will be adjusted to provide the necessary clamp
Quantum 1000 Base Station User 7) The final assembly can now be attached to the pole (figure Figure Diagrams that demonstrate the vertical angular displacement and a visual concept of how the antenna can be aligned are outlined in figures Quantum 1000 Base Station User Guide Rev 1.1, Page The final assembly can now be attached to the pole (figure 30). Figure 30- Antenna Mounted to Pole Diagrams that demonstrate the vertical angular displacement and a visual concept of how the antenna can be aligned are outlined in figures 31 and 32. Rev 1.1, Page 30 of 70 Diagrams that demonstrate the vertical angular displacement and a visual concept of how the antenna
Quantum 1000 Base Station User Figure 31 Quantum 1000 Base Station User Guide Rev 1.1, Page 31 – Antenna Vertical Angular Displacement Rev 1.1, Page 31 of 70
Quantum 1000 Base Station User 2.9 Ethernet This port allows remote command and control of the Base Station and also provides the data traffic backhaul interface that should be conneconnection is a straight-through 568 Quantum 1000 Base Station User Guide Rev 1.1, Page Figure 32 – Antenna Alignment This port allows remote command and control of the Base Station and also provides the data traffic backhaul interface that should be connected to the Service Provider’s network equipment. The cable through 568-B standard as shown below in figure 33. Rev 1.1, Page 32 of 70 This port allows remote command and control of the Base Station and also provides the data traffic cted to the Service Provider’s network equipment. The cable
Quantum 1000 Base Station User Figure In the case that the Base Station is mounted outdoors care it is important to ensure that the following points are followed. 1) You must install an appropriate outdoor rated, shielded Categorycable. 2) You must install a shielded 3) You must use shielded Cat 5with the metal RJ-45 connector4) A weatherized Ethernet connector backshell must be installed (Molex P/N 813969556) to weathprotect the connector. 5) The maximum distance from the Base Station to the Service Provider’s network equipment is limited to 100m. One recommendation for an outdoor rated Cat 5 Ethernet cable is: Name: Commscope 2003 Cat 5eDescripton: Outdoor ratedManufacturer: CommscopeDistributor: Anixter (http://www. For your information, the procedure to install Ethernet connectors is provided in Appendix C. Quantum 1000 Base Station User Guide Rev 1.1, Page 33 – Ethernet 568-B Straight Connection In the case that the Base Station is mounted outdoors care it is important to ensure that the following You must install an appropriate outdoor rated, shielded Category-5 (Cat 5) 100 Mbps Ethernet You must install a shielded outdoor rated metal RJ45 cable connector. You must use shielded Cat 5e cables and make certain that the drain wire has a good contact 45 connector A weatherized Ethernet connector backshell must be installed (Molex P/N 813969556) to weathThe maximum distance from the Base Station to the Service Provider’s network equipment is One recommendation for an outdoor rated Cat 5 Ethernet cable is: Commscope 2003 Cat 5e Outdoor rated, UV protection, shielded Cat 5e cable Commscope (http://www.anixter.com) For your information, the procedure to install Ethernet connectors is provided in Appendix C. Rev 1.1, Page 33 of 70 In the case that the Base Station is mounted outdoors care it is important to ensure that the following 5 (Cat 5) 100 Mbps Ethernet cables and make certain that the drain wire has a good contact A weatherized Ethernet connector backshell must be installed (Molex P/N 813969556) to weather The maximum distance from the Base Station to the Service Provider’s network equipment is For your information, the procedure to install Ethernet connectors is provided in Appendix C.
Quantum 1000 Base Station User 2.9.1 Weather Protection of the An IP67 compliant weather protection connector is provided along with the Base Station Sector. This will provide the means to weather protect the RJ45 Ethernet connection. Figure 34 is an illustration of the components that are includ Figure Note: Please remember to install all the pieces of the connector onto the cable before the RJ45 connector is crimped. The procedure to install the connector is given below. The instructions are provided assuming that one of the ends of the cable is accessible and does not have a RJ connector fitted. 1) Crimp the RJ45 connector to the cable (figure 3 Quantum 1000 Base Station User Guide Rev 1.1, Page Weather Protection of the Ethernet Connector An IP67 compliant weather protection connector is provided along with the Base Station Sector. This will provide the means to weather protect the RJ45 Ethernet connection. is an illustration of the components that are included in the protection connector. Figure 34 – Ethernet Weather Connection Please remember to install all the pieces of the connector onto the cable before the RJ45 The procedure to install the connector is given below. The instructions are provided assuming that one of the ends of the cable is accessible and does not have a RJ connector fitted. Crimp the RJ45 connector to the cable (figure 35). Figure 35 – Cable RJ45 Connector Rev 1.1, Page 34 of 70 An IP67 compliant weather protection connector is provided along with the Base Station Sector. This will ed in the protection connector. Please remember to install all the pieces of the connector onto the cable before the RJ45 The procedure to install the connector is given below. The instructions are provided assuming that one of
Quantum 1000 Base Station User 2) Take the plastic RJ45 holder and ensure that the rubber RJ45 cut out is stuck onto the RJ45 holder (figure 36) 3) Pull the cable plus RJ45 connector through the RJ 45 holder and ensure that is pulled tight into the holder. Ensure that the connector flap is locked in place (figure 3 Figure 3 Quantum 1000 Base Station User Guide Rev 1.1, Page Take the plastic RJ45 holder and ensure that the rubber RJ45 cut out is stuck onto the RJ45 Figure 36 – Plastic RJ45 Holder Pull the cable plus RJ45 connector through the RJ 45 holder and ensure that the RJ45 connector is pulled tight into the holder. Ensure that the connector flap is locked in place (figure 3 37 – Plastic RJ45 Holder plus RJ45 Cable Rev 1.1, Page 35 of 70 Take the plastic RJ45 holder and ensure that the rubber RJ45 cut out is stuck onto the RJ45 the RJ45 connector is pulled tight into the holder. Ensure that the connector flap is locked in place (figure 37).
Quantum 1000 Base Station User 4) Install the rubber ring around the cable and the other components as Figure 5) Tighten the end cable locks and the assembly is complete (figure 3 Quantum 1000 Base Station User Guide Rev 1.1, Page Install the rubber ring around the cable and the other components as shown in figure 3 Figure 38 – All Components Assembled Tighten the end cable locks and the assembly is complete (figure 39). Figure 39 – Complete Assembly Rev 1.1, Page 36 of 70 shown in figure 38.
Quantum 1000 Base Station User 6) The assembly can now be attached to the Base Station Sector thus creating a weather protected connection (figure 40). Figure 40 – Complete Assembly connected to Base Station Quantum 1000 Base Station User Guide Rev 1.1, Page The assembly can now be attached to the Base Station Sector thus creating a weather protected Complete Assembly connected to Base Station Rev 1.1, Page 37 of 70 The assembly can now be attached to the Base Station Sector thus creating a weather protected

Navigation menu