Maxon Electronics Australia MM-5500U CDMA EVDO USB Voice/Data Modem User Manual MM 5500U FCC

Maxon Electronics Australia Pty. Ltd. CDMA EVDO USB Voice/Data Modem MM 5500U FCC

users manual

FCC Documentation- MM-5500U CDMA 1x/EVDO Modem Confidential and proprietary information This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement. FCC Documentation MM-5500U CDMA 1x/EVDO Modem Version : 0.1 Date :JUN 21, 2004 Maxon Proprietary : Restricted DistributionThis document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement. 36a Gibson Avenue, PadstowNew South Wales, 2211. AustraliaPhone:+61 2 9707 2000URL: http//www.maxon.com.au
FCC Documentation- MM-5500U CDMA 1x/EVDO Modem 2/22 Confidential and proprietary information This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement. FCC RF EXPOSURE COMPLIANCE In August 1996 the Federal Communications Commission (FCC) of the United States with its actionin Report and Order FCC 96-326 adopted an updated safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC regulated transmitters. Those guidelinesare consistent with the safety standard previously set by both U.S. and international standardsbodies. The design of this phone complies with the FCC guidelines and these international standards. Use only the supplied or an approved antenna. Unauthorized antennas, modifications, or attachments could impair call quality, damage the phone, or result in violation of FCC regulations. This MM-5500U CDMA card has been tested for FCC RF exposure hand and body SARcompliance. In order to comply with FCC RF exposure requirements, this product must be operated with the MM-5500U CDMA card. The use of this card in any other type of host configuration may not comply with FCC RF exposure requirements and should be avoided. During operation, a 1.5cm separation distance should be maintained between the antenna,whether extended or retracted, and the user’s/bystander’s body (excluding hands, wrists,feet, and ankles) to ensure FCC RF exposure compliance. CAUTION Change or modification without the express consent of Maxon Electronics Australia Pty Ltd voids the user’s authority to use the equipment. This equipment has been tested and found to complywith the limits pursuant to Part 15 of the FCC rules. These limits are designed to providereasonable protection against harmful interference in an appropriate installation. This equipmentgenerates, uses, and can radiate radio frequency energy and, if not used in accordance with instructions, can cause harmful radiation to radio communication. However, there is no guaranteethat interference will not occur in a particular installation. If the equipment does cause harmfulinterference in radio and television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the followingmeasures:  Reorient or relocate the receiving antenna  Increase the separation distance between the equipment and the receiver  Contact Maxon Electronics Australia Pty Ltd Technical Support for assistance.
FCC Documentation- MM-5500U CDMA 1x/EVDO Modem 3/22 Confidential and proprietary information This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement. Table of contents 1. Contact Information·······························································································4 2. Product Overview ··································································································5 2.1 Overview........................................................................................................5 2.2 What is the MM-5500U CDMA 1x/EVDO Modem ........................................ 5 2.3 Supplied accessories...................................................................................5 3. Specifications ········································································································6 3.1 Mechanical Specifications...........................................................................6 3.2 Environment Specifications ........................................................................ 6 3.3 Electrical Specifications .............................................................................. 6 3.4 CDMA RF Specifications.............................................................................. 7 4. Instruction ·············································································································· 9 4.1 Supplied accessories...................................................................................9 4.2 Getting start ..................................................................................................9 5. Circuit description······························································································· 14 5.1 MM-5500U CMDA 1x/EVDO Modem circuit description ..........................14 5.2 Power interface part...................................................................................15 5.3 Digital part...................................................................................................15 5.4 RF part......................................................................................................... 16 6. Range of operating power levels and description of means for variation of operating power··································································································· 18 7. Description of frequency determining and stabilizing circuitry······················ 19 8. Description of circuit employed for suppression of spurious radiation········ 20 9. Description of modulation system used ···························································21
FCC Documentation- MM-5500U CDMA 1x/EVDO Modem 4/22 Confidential and proprietary information This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement. 1. Contact Information If you have any technical queries about this manual, please contact: Maxon Electronics Australia Pty. Ltd. 36a Gibson Avenue Padstow, New South Wales 2211 Australia Phone: +61 2 9707 2000 Fax: +61 2 9707 3328 Mr. Ray Sanders-Managing Director Mr. Ashween Prasad- Technical Manager Email: engineering@maxon.com.au
FCC Documentation- MM-5500U CDMA 1x/EVDO Modem 5/22 Confidential and proprietary information This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement. 2. Product Overview 2.1 Overview The MM-5500U CDMA 1x/EVDO Modem is designed to merge the capabilities of 3G 1x EV standard with the high value feature sets supported by 3G 1x MC IS-2000. The MM-5500U is capable of 2.4Mbps peak data rate on the forward link and 153Kbps peak data rate on the reverse link. The MM-5500U solution enables up to a doubling of overall IS-95-A/B voice capacity and new, higher-data-rate services. 2.2 What is the MM-5500U CDMA 1x/EVDO Modem - IS-95A/B, cdma2000-1X and EVDO CDMA Protocol Support - Remote controlled by AT commands - Data transmission up to 2.4Mbps [forward link], 153Kbps [reverse link] - LED indicating of the modem status 2.3 Supplied accessories - MM-5500U CDMA 1x/EVDO Modem (1) - Ear-piece assembly (1) - USB interface cable assembly (1) - Deriver CD (1)
FCC Documentation- MM-5500U CDMA 1x/EVDO Modem 6/22 Confidential and proprietary information This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement. 3. Specifications 3.1 Mechanical Specifications Table 3.1 mechanical specifications Dimensions 58mm x 38mm x 12mm, except antenna & USB connector parts Weight Approx. 35g , except ear-piece & USB cable assemblies Housing Material ABS 3.2 Environment Specifications Table 3.2 environment specifications Operating conditions 0°C ~ +60°C , 85%(at 50(C), relative humidity (non-condensing) Storage Temperature -40°C ~ +70°C Humidity 95%, non-condensing 3.3 Electrical Specifications Table 3.3 Current Consumption - DC input voltage +5VDC from USB port - Maximum current Under 850mA - Typical current Under 200mA - Digital block operating voltage +3.0V (typical) On communication @ Maximum TX Power (24+/- 0.3dBm) Under 700mA (Note) The current consumption might vary of 5% over the whole operating temperature range.
FCC Documentation- MM-5500U CDMA 1x/EVDO Modem 7/22 Confidential and proprietary information This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement. 3.4 CDMA RF Specifications RF performances are compliant with IS-95A/B, cdma2000-1X RTT CDMA Protocol. 3.4.1 Transmitter specifications Table 2.4 Transmitter performance Type of Multiplexing Frequency-Division Duplex Frequency Range 824.64MHz ~ 848.37MHz Channel Number 20CH Bandwidth 1.23MHz Occupied Bandwidth Under 1.32MHz Type of Oscillation PLL Synthesizer & VCTCXO(19.2MHz) VCO Output Frequency Range ( divide-by-2 frequency range) 1372.08MHz ~ 1421.54MHz (686.04MHz ~ 710.77MHz) Intermediate Center Frequency 138.6MHz Modulation Method OQPSK RF Maximum Output Power 0.28W (24.5dBm/1.23MHz) Frequency Stability(Accuracy) Under defined freq. +/- 300Hz Waveform Quality Over 0.944 Conducted Spurious Emission Over carrier +/-900KHz, -42dBc/30KHz Over carrier +/-1980KHz, -54dBc/30KHz Common RF Impedance 50ohm Supplied voltage +3.8V DC @ Power Amp. +2.85V DC @ TX block
FCC Documentation- MM-5500U CDMA 1x/EVDO Modem 8/22 Confidential and proprietary information This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement. 3.4.2 Receiver specifications Table 2.5 Receiver performance Type of Receiving Super Heterodyne Method Frequency Range 869.94MHz ~ 893.37MHz Channel Number 20CH Band width 1.23MHz Type of Oscillation PLL Synthesizer & VCTCXO(19.2MHz) VCO Output Frequency Range ( divide-by-2 frequency range) 1372.08MHz ~ 1419.54MHz (686.04MHz ~ 709.77MHz) Intermediate Center Frequency 183.6MHz Modulation Method QPSK Receiver Sensitivity Under -104dBm @FER=0.5% Single Tone Desensitization (-30dBm @FC +/-900KHz) Under -101dBm @FER=1% -43dBm Under -101dBm @FER=1% -32dBm Under -90dBm @FER=1% Inter-modulation (Fc +/-900KHz&1.7MHz) -21dBm Under -79dBm @FER=1% Common RF Impedance 50ohm Supplied voltage +3.0V DC
FCC Documentation- MM-5500U CDMA 1x/EVDO Modem 9/22 Confidential and proprietary information This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement. 4. Instruction Warning • To prevent fire or shock hazard, do not expose the unit to rain or moisture. • Do not drop the unit or give a shock to the unit, or it may cause a malfunction. 4.1 Supplied accessories - MM-5500U CDMA 1x/EVDO Modem with antenna (1) - USB cable assembly (1) - Earpiece assembly (1) 4.2 Getting start Before you can begin using the MM-5500U CDMA 1x/EVDO Modem, you must: 4.2.1 Install Phone UI program and MM-5500U Modem Insert installation CD (supplied with the Telstra CDMA Voice/Data Modem) into the CD-ROM drive. This will automatically start the installation and install the required drivers plus Telstra CDMA Voice/Data Modem Application software. Do not connect Telstra CDMA Voice/Data Modem into your laptop/PC yet. The installation procedures are the same for Windows 98 Original Edition, Windows 98 Second Edition, Windows ME, Windows 2000 and Windows XP. It’s very important that you must install MM-5500U Modem by this procedure! 4.2.1.1 Start Autorun
FCC Documentation- MM-5500U CDMA 1x/EVDO Modem 10/22 Confidential and proprietary information This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement. 4.2.1.2 Install shield Wizard… click ‘Next’ 4.2,1.3 Ready to install the Program 4.2.1.4 Maxon Electronics Australia EVDO Modem is configuring your new software installation
FCC Documentation- MM-5500U CDMA 1x/EVDO Modem 11/22 Confidential and proprietary information This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement. 4.2.1.5 Copying file 4.2.1.6 Maintenance Complete
FCC Documentation- MM-5500U CDMA 1x/EVDO Modem 12/22 Confidential and proprietary information This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement.
FCC Documentation- MM-5500U CDMA 1x/EVDO Modem 13/22 Confidential and proprietary information This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement. 4.2.2 Connect ear-piece to the ear-jack connector if you want to use as a phone. Microphone and earphone signals for Voice Call are provided to interface with headset directly. 1. Connect the ear-piece plug firmly the ear-jack port hole. 2. Ware the Ear-piece to the left or right ear and adjust the ear-piece to fit to your ear firmly. - Press for more than a second during buzzer ringing for receiving voice call - Press for more than a second when redial, this time you heard dialing sound When adjusting the volume on the unit, please refer to the “MM-5500U Software manual” for detail information. 4.2.3 LED display Table 4.2.1 LED function descriptions LED Color Function RED GREEN YELLOW POWER ON ON OFF OFF ACQUISITION- Fail FLASH OFF OFF ACQUISITION- OK (IDLE) OFF ON OFF VOICE CALL ON ON OFF DATA CALL OFF ON FLASH DORMANT OFF ON ON
FCC Documentation- MM-5500U CDMA 1x/EVDO Modem 14/22 Confidential and proprietary information This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement. 5. Circuit description 5.1 MM-5500U CMDA 1x/EVDO Modem circuit description The MM-5500U CDMA 1x/EVDO modem consists of the CDMA Engine, power generation part, digital part, RF part and connectors. The Fig 5-1 is block diagram of MM-5500U CDMA 1x/EVDO modem. Logic partRxTxSynthesizerRF partLNAPowerAmpMSM5500Memory-Flash(64Mb)-SRAM(32Mb)PowerinterfaceU701MIC39102(LDO)Iout=1AVout=3.8VRF VccAudio interface signalEar-jackportCDMA EngineMM-5500U Block DiagramprotectionDUXDC5VDebug Port*only testCDMAAntennaLEDU703ISP1105W(USBtransceiver)D+D-USBConnector(DWAP-02-04)RF S/W Figure 5.1 MM-5500U CDMA 1x/EVDO modem block diagram
FCC Documentation- MM-5500U CDMA 1x/EVDO Modem 15/22 Confidential and proprietary information This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement. 5.2 Power interface part DC Power is supplied from the USB connector. - LDO(U701): This component is low dropout regulator. Output voltage is about 3.8V DC. This LDO output voltage is inputted to CDMA Engine power interface. Each block of CDMA Engine uses low-drop-output linear regulator. - U500 : voltage regulator for digital circuit ( 2.8 DC ) - U501 : voltage regulator for VC-TCXO and IFR3300 ( 3.0V DC ) - U502 : voltage regulator for RF Rx part ( 3.0V DC ) - U503 : voltage regulator for RF Tx part ( 2.85V DC ) - U505 : voltage regulator for digital part(2.7V DC ) - And power AMP is directly supplied. 5.3 Digital part - U400 : MSM(Mobile Station Modem) ASIC is chip responsible for CDMA/FM mobile station’s base-band digital signal processing. For this chip to function, TCXO(19.2MHz) is required as basic clocks. And sleep crystal (32.768KHz) is used as clock source of MSM ASIC. MSM consists of CDMA core and DFM core. CDMA core is a part for processing CDMA signal consisting of modulator/demodulator, interleaver/deinterleaver and encoder/decoder in the CDMA mode. - U401: Memory part consists of Flash memory and SRAM. Flash memory: store to main program. SRAM: performs to read and write data - U703: USB transceiver is fully compliant with the USB specification Rev1.1.
FCC Documentation- MM-5500U CDMA 1x/EVDO Modem 16/22 Confidential and proprietary information This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement. 5.4 RF part RF part consists of synthesizing part, transmission and reception part. Fig 5.2 RF part block diagram
FCC Documentation- MM-5500U CDMA 1x/EVDO Modem 17/22 Confidential and proprietary information This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement. 5.4.1.1 Frequency synthesizing part Frequency synthesizing part called PLL Synthesizer consists of three synthesizer circuit which is first local synthesizer, Tx IF synthesizer and Rx IF synthesizer. The first local synthesizer generates the primary local system oscillation frequency, operating over 1372.08 ~ 1419.54 MHz frequency range. Tx IF and Rx IF synthesizer generate the second local oscillation frequency, 267.2 MHz and 367.2 MHz respectively. 5.4.1.2 Receiving part - Duplexer. The duplexer filters the RF signal transmitted through Antenna and sends the signals to LNA. - LNA. This part in front-end is used to amplify the received signal with low noise figure - Down converter. It acts as a mixer using first local frequency to produce the desired signal in the mid-range frequency of 183.6 MHz. - Rx AGC. This part is designed to control the gain of the dynamic range of midrange frequency produced in down converter according 80 dB dynamic range. Currently, previous BBA is divided into IFR3300(Rx IF-baseband converter) and RFT3100(Tx baseband-IF converter). IFR3300 acts as the baseband analog processor which processing the signals between the IFR3300 and digital processing circuit. In the while, RFT3100 consists of Tx AGC and Tx part analog processor of previous BBA. 5.4.1.3 Transmission part - Tx AGC. It is designed to be gain-controlled from 84 dB dynamic range. The gain of this part is controlled by MSM using digital control signal. - Up converter. This part mixes the IF transmission frequency 138.6 MHz and the first local 1372.08 ~ 1419.54 MHz to generate transmission frequency of 824.64 ~ 848.37 MHz. - Power AMP module. This part is designed to work in 824 MHz ~ 849 MHz frequency range in the CDMA mode and can generate the proper output power. The DC voltage into the power amp module is typical 3.8V.
FCC Documentation- MM-5500U CDMA 1x/EVDO Modem Confidential and proprietary information This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement. 6. Range of operating power levels and description of means for variation of operating power Dynamic range of output power is from –56dBm to +24.5dBm with ±0.3dB variation in CDMA mode. A temperature-compensated TX AGC (Automatic Gain Control) amplifier with 85dB gain range is included in the RFT3100. The transmit output power level is directly controlled by varying the gain of this TX AGC amplifier. A DC input voltage from the MSM5500 linearly controls the gain of the TX AGC amplifier. The 84 dB dynamic range is 39 dB when the voltage 2.8V and -45 dB in 0.1V. The 81 dB dynamic range (0.3V ~ 2.4V) gain is used in this CDMA card.
FCC Documentation- MM-5500U CDMA 1x/EVDO Modem Confidential and proprietary information This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement. 7. Description of frequency determining and stabilizing circuitry Frequency synthesizing part is composed of the first local RX IF synthesizer which is single mode PLL synthesizer and the internal Tx IF and Rx IF synthesizer which are in RFT3100 and IFR3300 chip. These parts generate the first local oscillation frequency, Rx IF frequency and Tx IF frequency. - First local frequency Synthesizer : 1372.08 MHz ~ 1419.54 MHz PLL loop is composed of single PLL synthesizer, Loop filter, VCO and VC-TCXO It generates transmission and reception frequency of 1372.08 MHz ~ 1419.54 MH - Rx IF synthesizer : 367.2 MHz Rx IF PLL loop is consisted of PLL synthesizer in the PLL module, VCO built in IFR3300, loop filter and VC-TCXO(Crystal oscillator 19.2 MHz). It oscillates twice the intermediate receiving frequency of 367.2 MHz and then generates 183.6 MHz, Rx IF frequency. - Tx IF Synthesizer : 267.2 MHz The configuration of PLL loop is composed of PLL Synthesizer, VCO which is internally installed, loop filter and VC-TCXO(19.2 MHz). It oscillates twice of the transmission intermediate frequency of 267.2 MHz and then generates Tx IF frequency of 138.6 MHz through the PLL loop. The frequency of 19.2 MHz generated from the VC-TCXO is the main clock of each the frequency synthesizer part. PLL frequency stability is determined by the stability of oscillator of VC-TCXO. This prevents maximum frequency variation from exceeding ±2.0PPM.
FCC Documentation- MM-5500U CDMA 1x/EVDO Modem Confidential and proprietary information This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement. 8. Description of circuit employed for suppression of spurious radiation In the CDMA transmit signal path, the frequency spectrum at the output of the CDMA DACs contains unwanted frequency components due to the DAC output transition edges and transients. The transmit clock frequency and harmonics are found in the spectrum. Each CDMA DAC is followed by an anti-aliasing low-pass filter with a bandwidth of 630 KHz that reduces unwanted frequency components installed in MSM5500. And then Tx IF frequency from the RFT3100 is filtered by band-pass filter. The nominal specification of the filter is as following. - Nominal center frequency : 138.6 MHz - 3 dB Bandwidth : ± 630 kHz - Stop band attenuation : 40dB min. The Tx RF output of the Tx Mixer and the AGC amp is filtered again by the SAW band pass filter. The nominal specification of the filter is as follows. - Pass band : 824 MHz ~ 869 MHz - Attenuation : DC ~ 800MHz : 22 dB min. 869 MHz ~ 1049 MHz : 25 dB min. 1049 MHz ~ 2000 MHz : 19 dB min. Finally, the spurious generated from Power AMP is filtered by the duplexer. The nominal specification of the duplexer is as follows - TX Pass band : 824 MHz ~ 869 MHz - Attenuation : 869 MHz ~ 894 MHz : 40 dB min.
FCC Documentation- MM-5500U CDMA 1x/EVDO Modem 21/22 . confidential and proprietary information This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement 9. Description of modulation system used The MM-5500U CDMA card consists of MSM, baseband analog interface (RFT31000, IFR3300) as modulation system. The MSM integrates functions of a CDMA processing, a digital FM(DFM) processing, CDMA subsystem in the MSM performs CDMA signal processing about CDMA modulation / demodulation, viterbi coding/decoding, interleaving/de-interleaving, and etc. The CDMA baseband processor performs forward-link demodulation, time tracking and reverse-link modulation for CDMA digital signals. The following figure shows a CDMA digital baseband processor block diagram. Figure 9.1 CDMA digital Baseband Block Diagram The modulator performs the orthogonal modulation, long code PN spreading and quadrature spreading. The resulting data stream is then band limited with FIR filters and sent to the analog baseband processor. The RFT3100 Transmit Signal Path (shown in figure 8-2) accepts analog I and Q data from the MSM and outputs modulated IF centered at 138.6 MHz to the RF transmitter. The RFT3100 transmit path outputs a differential IF signal with spread spectrum modulation expending ±630KHz from the transmit IF center frequency of 138.6 MHz. The analog I and Q baseband components from the CDMA low-pass filters are mixed in quadrature with unmodulated I and Q signals at 138.6 MHz. After mixing, the I and Q IF components are summed and output differentially. The 138.6 MHz I and Q IF VCO signals are generated on the RFT3100.
FCC Documentation- MM-5500U CDMA 1x/EVDO Modem 22/22 . confidential and proprietary information This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement The transmitter IF VCO is set to 267.2 MHz by an external varactor-tuned resonant tank circuit. An internal phase-lock loop and external loop filter network provides the feedback to the varactor that tune the VCO precisely to 267.2 MHz. A master-slave divide-by-two circuit generates I and Q signals in precise quadrature for the mixers.

Navigation menu