Mascot Electric UF-16HE Wireless Microphone system User Manual 01

Mascot Electric Co., Ltd. Wireless Microphone system 01

Users Manual

- Connecting the Receiver- Set up the Handheld Microphone / Bodypack transmitter- Receiver- Handheld Microphone- Bodypack transmitter- FCC Statement- Safety - Environmentz Product Description.................................................................. 2z Introduction............................................................................. 1z System Operation..................................................................... 6z Trouble Shooting...................................................................... 8z System Feature........................................................................ 8z System Specification............................................................... 9
WIRELESS INTRODUCTION  FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device. zIntroduction Thank you for purchasing our product. This PLL synthesized wireless microphone system operates in UHF band frequency with 16 selectable channels. Please read this instruction manual carefully before operating the system. This manual covers the function and operation of the wireless microphone system.  Safety ¾Do not spill liquid on the appliance and do not drop it on a hard concrete floor. ¾Do not place the equipment near heat sources such as radiators, heating ducts, amplifier, etc.¾If the equipment is not going to be used for a long time, disconnect the AC adapter from the power outlet. Please note that if you turn the equipment off while leaving the AC adapter plugged in, it is not fully isolated from the power supply.¾Do not expose the equipment to direct sunlight, extremely dust, excessive moisture, rain, mechanical vibrations, or shock.¾Take out the battery from transmitter, if the appliance has been not used for a longer period.This will avoid the damage resulting from a defective leaking battery. ¾WARNING: To reduce the risk of fire or electric shock, do not use the products near water and do not expose them to rain or moisture. ¾No guarantee claims for the equipment and no liability for any resulting personal damage or material damage will be accepted if the equipment are used for other purpose than originally intended, if the equipment are not correctly connected or operated, or if the equipment are not repaired in an expert way.  Environment ¾Do not throw used batteries into a fire or garbage bin with domestic rubbish. Be sure to dispose of used batteries in accordance with local waste disposal rules. ¾When disposing the equipment, remove the batteries, separate the case, circuit boards, and cables, and dispose of all components in accordance with local waste disposal rules.1
WIRELESS PRODUCT DESCRIPTION zProduct Description ¾ Receivers The receivers are used with our 16-channel selectable channels transmitters. (The number of frequency channels depends on local regulations.) The receiver operates in UHF band frequency with PLL synthesized control. Powered by 12V DC. !¾ Single ChannelSwitching Diversity, Front Fixed Antenna 1 2 3 441.Antenna 2.Power Indicator: The LED lights up to show the receiver is ready to operate. 3.AF Indicator: The LED lights up to show the reception of AF signal.4.Diversity A/B Indicator: The LED lights up to show the reception of RF signal. 2
WIRELESSPRODUCT DESCRIPTION1. Balanced XLR Audio Output 2. Unbalance 6.35mm Audio Output 3. MIC/LINE Switch: Use this to adjust the audio output level for MIC level (-20dB) or LINE level (0dB). 4. Squelch: Turn the switch to adjust or decrease the noise floor level. 5. Power Adapter Connector1 2 3 4 5 63
WIRELESS PRODUCT DESCRIPTION ¾ Handheld Microphone 15634271. Grille: Protects the microphone capsule and helps reduce breath sounds and wind noise. The grille for the various microphone capsules differ in appearance.2. Power LED: Indicate the power / low battery level status.3. Power: Press for 2 seconds to turn transmitter on or off.4. Battery Compartment: Insert two AA dry or rechargeable batteries into the compartment and make sure that the polarity of batteries is correct. 5. Channel Selector: 16 different selectable frequencies. 4LED Indicator Status Red Ready Flashing Red Low Battery power when less than 10 minutes operation
¾ Bodypack Transmitter WIRELESS 51. Power / MUTE Button: Press for 2 seconds to power the microphone on or off. With the transmitter on, a slight press for button will toggle between mute and unmute function. 2. 3.5Ø Connector: connect to the lapel microphone or headset microphone. 3. Power / MUTE LED: Indicate the power / mute / low battery level status. 4. Channel Selector: Changes the transmitter Channel setting. 5. Gain Switch: The rotary control adjusts the input audio level of the transmitter. The gain adjustment range is 10dB.6. MIC/LINE Switch: The switch set the audio input to MIC level or LINE level. 7. Battery component: Insert two AA dry or rechargeable batteries into the compartment and make sure that the polarity of batteries is correct. LED Indicator Status Red Ready Flashing Red Low Battery power when less than 10 minutes operationBlue MUTE Flashing Blue MUTE on and low battery power when less than 10 minutes operation
6Connected the provided DC power supply to thereceiver power input with an appropriate ACpower source. The power LED display will light and the receiver is on.¾Using a standard audio cable with 3-pin XLR connectors or 6.3mm phone plugs to connect the mixer or amplifier.¾Set the audio output level for MIC: -20dB LINE: 0dB ¾Never use the balanced and unbalanced audio outputs at the same time! This may cause signal loss or increased noise.zConnecting the receiverPrior to setting up, please check that the transmitter and receiver are tuned to the same frequency or channel. Two or more transmitters operating in the same frequency can not be used at the same time and area.1234AC/DCADAPTERLINE MICUse squelch to avoid reproducing noise when the receiver does not receive enough signal from the transmitter.¾Turn clockwise to increase squelch and reduce noise. When turning the squelch knob clockwise, it begins to eliminate background noise.-When the squelch is all the way to the left, the squelch is off and the ambient RF noise will be easily to receive.-SYSTEM OPERATION
Open the battery cover and insert batteries into the battery compartment conforming to the polarity (+)(-) marks.¾ Unscrew the handheld Mic and open the battery cover to insert the battery into the battery compartment and confirm the marks of the polarity (+) (-).¾ Press for 4 seconds to turn the Handheld/ Bodypack transmitter on.¾ If the LED stays flashing , it indicates that the battery will out of power soon and should be changed. zSet up the handheld microphone / bodypack transmitterNOTE: When you don’t use this device for a long term period, please switch the power switch to “off” mode to save more electric power. 67891011 121234567891011 1212345SYSTEM OPERATION Adjust the audio input level. ¾OPEN7
WIRELESS TROUBLE SHOOTINGzTroubleshooting Problem Solution No sound ¾ Check the power supply of the microphone and receiver. ¾ Check that the transmitter and receiver are tuned to the same frequency. ¾ Check whether the hi-fi appliance is switched on and the receiver output is connected to audio mixer or amplifier input. ¾ Check whether transmitter is too far away from receiver or SQUELCH control set too high. ¾ Check whether receiver is located too near metal object or there are obstructions between transmitter and receiver. Sound interference ¾ Check the antenna location. ¾ When using 2 or above microphone sets simultaneously, make sure that the chosen frequencies are not interfered. ¾ Check whether the interference comes from other wireless microphones, TV, radio and etc. Distortion ¾ Check the receiver volume level is set too high or too low. ¾ Check whether the interference comes from other wireless microphones, TV, radio and etc. zSystem Feature¾ Operating in UHF band frequency with synthesizer controlled. ¾The wireless microphone system with 16 selectable frequencies via Phase Locked Loop (PLL) circuitry makes it easy to choose non-interfered channels. ¾ Diversity with two antennas to ensure the reception quality. ¾Super high sensitivity, extremely low noise transmission and reception. ¾ SMT assembled PCB module ensures the quality and stability. 8
WIRELESS FEATURES & SPECIFICATION zSystem Specification Receiver Handheld Microphone/Bodypack Transmitter DESIGN AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE. : UHF 520 - 698MHz: Mini case: PLL Synthesized: FM ±20KHz: ±0.005% : ＞: ＞50dB: 80Hz to 18KHz : ＜1% (at 1KHz): 1st: 243.95MHz 2nd:10.7MHz : ＞100dB : 32.768KHz : Balanced & Unbalanced : 120mA ± 10mA: 170×42×106¾ ¾Case¾ ¾ ¾ ¾ ¾ ¾ ¾ Selectivity¾ ¾ T.H.D.¾ ¾ ¾ ¾ ¾ ¾ ¾Dimension (mm)W×H×D¾ ¾ Channel Select¾ ¾ ¾ ¾ Deviation¾ ¾ T.H.D.¾ ¾ Tone Key¾ Mic Unit¾ ¾Dimension (mm)W×H×D: UHF 520 - 698 MHz: 10mW (MAX) : PLL Synthesized : ± 0.005%: <1% (at 1KHz) : 32.768KHz: 120mA ± 10mA9
FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices).

Navigation menu