Mad Catz D232266A3713C GameSmart C.T.R.L.R User Manual 32266 MUG 13SEP13

Mad Catz, Inc. GameSmart C.T.R.L.R 32266 MUG 13SEP13

UserManual.wiki >

D232266A3713C User Manual >

Users Manual - part 2 of 2

Contents

1. Users Manual - warranty & compliance sheet
2. Users Manual - part 1 of 2
3. Users Manual - part 2 of 2

Users Manual - part 2 of 2

.8LED INDICATORSINITIAL SETUP 1. Insert fresh batteries into the battery compartment2. Ensure the controller is OFF (no LED lights) 3. Set Mode Switch to one of below modes:• When connecting to Windows PC or Mac OS X, set Mode Switch to:• When connecting to Android OS/M.O.J.O. console, set Mode Switch to: Product is connected to a device but battery is lowProduct is connecting to a devicePairing Info is removedProduct is connected to a deviceBLINKING REDSOLID PURPLE SOLID RED BLINKING BLUE Product is ON and not connected to a deviceBLINKING BLUE TO RED CONNECTING VIA BLUETOOTH1. Press and hold the “Home” button on the controller until its LED blinks blue and red2. Ensure Bluetooth is enabled on your phone, M.O.J.O. console, tablet or computer3. Select ‘search for devices’ on your device4. Choose ‘Mad Catz C.T.R.L. R’ under the Device List to connect5. Once connected, the LED indicator will blink blue. The controller is ready to use

.9SETUP INSTRUCTIONSMOUSE MODER1L1R2R1L2L1R2L2MOUSE Y AXISHOMEESCENTERMIDDLE CLICKSPACE BARRIGHT CLICKLEFT CLICKSCROLL UPSCROLL DOWNMOUSE X AXIS1. When the controller is connected via Bluetooth, it can also be used as a mouse control for your connected device2. Set the Mode Switch to and use the left analog stick and shoulder buttons to navigate the deviceR2R1L2L1L2SHOULDER BUTTONSLeft ClickShift Backspace / Internet browser backR1L1R2R1L2L1R2L2R1L1R2R1L2L1R2L2R1L1R2R1L2L1R2L2R1L1R2R1L2L1R2L2Right ClickShift & Spacebar /Internet browser page upR1L1R2R1L2L1R2L2R1L1R2R1L2L1R2L2R1L1R2R1L2L1R2L2R1L1R2R1L2L1R2L2Shift & Backspace /Internet browser forwardSpacebar /Internet browser page down

.10SETUP INSTRUCTIONSUNPAIRING THE DEVICETURNING THE DEVICE ON/OFF1. Press and hold the “Start” button for ﬁve seconds until the LED shines red. The LED will then blink blue and red indicating paired info is removed and the controller is back in discovery mode2. Go into Bluetooth Settings, select ‘Mad Catz C.T.R.L.R’ and choose to ‘Forget the Device’Press and hold the “Home” button on the controller for 3 seconds.MAD CATZ A.P.P. PROGRAMMING SOFTWARE1. Follow the above instructions for connecting to a Windows PC, or Mac OS X2. Download and install the desktop software from www.madcatz.com/downloadsThis software enables controller programming.

.11FIRMWARE UPDATESThe C.T.R.L. R is ﬁrmware upgradeable and future-proofed against upcoming developments in Bluetooth/mobile gaming. As Bluetooth Smart becomes more widely implemented on mobile devices, Mad Catz will release an update that will enable your C.T.R.L. R to intelligently determine connectivity to your devices. With the addition of Bluetooth Smart, the C.T.R.L. R gains reduced latency and increased battery life. When Android 5.0 and/or Bluetooth 4.1 are enabled on your device, check www.madcatz.com for announcements on our ﬁrmware update software, and how you can get more out of your GameSmart C.T.R.L. R.*Cable not included

ENFCC & IC WARNING This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS stan¬dard (s). Operation is subject to the following two condi-tions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC RADIATION EXPOSURE STATEMENT: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or trans¬mitter. IC RF EXPOSURE STATEMENT: The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that, the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.EU DECLARATION OF CONFORMITY:As required, certain of these products have been tested and conform to the requirements of the European Union Directives 2002/95/EC, 2002/96/EC, and 2004/108/EC. Authorized signatory of the manufacturer is Mad Catz, Inc., 7480 Mission Valley Road, Suite 101, San Diego, CA 92108.

FRAVERTISSEMENT DE LA FCC & IC (INDUSTRY CANADA) Cet appareil répond aux exigences de la section 15 de la réglementation FCC et aux normes RSS sans licence d’Industry Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1) Ce périphérique ne doit pas provoquer d’interférences nuisibles et (2) il doit accepter toute inter¬férence reçue, y compris les interférences susceptibles de causer un dysfonctionnement. Tout changement ou toute modiﬁcation n’ayant pas été expressément approuvé(e) par l’entité responsable de la conformité peut annuler le droit de l’utilisateur à se servir de cet équipement. DÉCLARATION DE LA FCC RELATIVE À L’EXPOSITION AU RAYONNEMENT ÉLECTROMAGNÉTIQUE : Ce matériel est conforme aux exigences de la FCC relatives aux limites d’exposition au rayonnement établies dans le cadre d’un environnement non contrôlé. Cet émetteur ne doit pas être combiné à ou fonctionner simultanément avec une autre antenne ou un autre émetteur. DÉCLARATION D’IC RELATIVEMENT AUX RADIOFRÉQUENCES : Cet appareil répond aux exigences lui permettant d’être exempté des limites de l’évaluation de routine exposées à la section 2.5 de la norme RSS 102 et est conforme aux limites d’exposition aux RF établies par la norme RSS-102. Les utilisateurs peuvent obtenir des informations du gouvernement canadien relatives à l’exposition aux RF et à la conformité. Conformément à la réglementation d’Industry Canada, cet émetteur radio doit uniquement fonctionner à l’aide d’une antenne dont le type et le gain maximum (ou moindre) ont été jugés aptes au fonctionnement avec l’émetteur par Industry Canada. Pour réduire le risque d’interférence radio pour les autres utilisa-teurs, le type d’antenne et son gain doivent être choisis de façon à ce que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas celle nécessaire pour une bonne communication.DÉCLARATION DE CONFORMITÉ DE L’UEComme exigé, certains de ces produits ont été testés et sont conformes aux exigences aux directives de l’Union Européenne 2002/95/EC, 2002/96/EC, et 2004/108/EC. Le signataire autorisé du constructeur est Mad Catz, Inc., 7480 Mission Valley Road, Suite 101, San Diego, CA 92108.