META System S p A 97802 Telematic Tracking System User Manual 5040273800 Man SatRC09 EN

META System S.p.A. Telematic Tracking System 5040273800 Man SatRC09 EN

User Manual

SAT RC 09INSTALLATION MANUALCAUTION- Only carry out the operations described in this manual.- The installer is not authorized to remove the warranty seals or to access the interior parts of the products or accessories.- The installer is not authorized to modify and/or adapt the product or the relative accessories.- The manufacturer declines all liability for damage to persons and/or property caused by incorrect installation of the product.TECHNICAL SPECIFICATIONSDimensions and weight:....................................................................................104X75X27, 168gPower supply voltage:................................................................................................12 VDCTemperature:..........................................................................................................-25º+70ºCPower input*:.............................................................................................................<2mA*With the peripheral device connected, the GPS off, Sat Programmer disconnected and the internalbuffer battery charged.Maximum current:.............................................................................................................<210mADISCONNECT THE VEHICLE’S BATTERYGROUNDBATTERYPOSITIVE(+12V)IGNITIONKEY POSITIVE(+15)GSMANTENNA1ENPRESSTO RELEASEGPSANTENNARelease and position the leveras shown in the figure beforeconnecting the 18-pin looseconnector to the terminal.CONNECTORCONNECTIONSLock the connector to the terminal by positioning the leveras shown in the figure.Connect the connectorsto the terminalPHASE2PHASE3PHASEFig.2Fig.3 Fig.4WARNING: make sure that the connector is insertedand locked to the terminal in the correct way.* : MANDATORY5040273800+155ASATPROGRAMMER*+12GNDFig.1DARK BLUEMAROONGENERAL LAYOUTSee pic. 5
• Position the device in a concealed part of the vehicle, inside the passenger compartment• To allow the diagnosis and testing operations to be carried out without difficulty, it is essential to install the device in a position where it can be easily reached with the cable of the Sat programmer.• Do not install the device under a mat, where it could be trodden on or crushed by a load.• It is advisable to lock the device to a rigid part of the vehicle.HOW TO POSITION THE DEVICEHOW TO POSITION THE CRASH SENSORGSMANTENNAONCE YOU HAVE CHOSEN THE POSITION FOR THE ANTENNA, MAKE SURE THAT THE RECEPTION IS GOOD BEFORE FIXING IT IN PLACE:- CONNECT THE SAT PROGRAMMER AND TEST TO MAKE SURE THAT EVERYTHING WORKS PROPERLY BY MEANS OF THE APPROPRIATE FUNCTION (CONSULT THE RELATIVE MANUAL).IT MUST NOT BEVISIBLE OR EASILYACCESSIBLE FROMTHE OUTSIDEDO NOT COVER WITHPARTS OR METALLICPAINTSCAREFULLYCLEAN THEFIXING SURFACETHE ANTENNA IS RESIN-COATED AND CANTHEREFORE BE INSTALLEDON THE OUTSIDE OF THEVEHICLE (E.G. UNDER THEMUDGUARDS, IN AHEADLIGHT......)HOW TO CONNECT THE GSM ANTENNAFig.6Fig. 7 Fig. 8 Fig. 9Fig. 10FIXING WITH SPACERUse the supplied spacer to install the sensor on a flat surface, oppositethe fastening tabs (e.g. longitudinal frame members on the PASSENGER’SSIDE, surfaces BELOW the sensor).The sensor must NOT be turned. Comply with the position indicated on thesticker affixed to the side of the sensor.HOW TO INSERT THESPACERFIXING IN THE VEHICLEPay particular attention tothe direction in whichthe spacer is inserted.!TOPTOP OFVEHICLELEFT SIDEOF VEHICLERIGHT SIDEOF VEHICLEFRONT OFVEHICLE• Fix the sensor temporarily in place with the screw.• Check the position of the sensor by means of the relative Sat Programmer menu.• Fix the sensor permanently in place.XYXTOP OFVEHICLELEFT SIDEOF VEHICLERIGHT SIDEOF VEHICLEFRONT OFVEHICLEXYFRONTCONNECTIONCRASH SENSORCAUTION!CHECK THE CORRECTCONNECTIONCLICK!CLICK!Fig.5OK OK OKOKYX0
THE ANTENNA IS RESIN-COATED AND CANTHEREFORE BEINSTALLED ON THEOUTSIDE OF THE VEHICLE(E.G. UNDER THEMUDGUARDS, IN AHEADLIGHT......)90°NO OKIT MUST NOT BEVISIBLE OR EASILYACCESSIBLE FROMTHE OUTSIDEDO NOT COVER WITHPARTS OR METALLICPAINTSKOOKONCE YOU HAVE CHOSEN THE POSITION FOR THE ANTENNA,MAKE SURE THAT THE RECEPTION IS GOOD BEFORE FIXINGIT IN PLACE:- DRIVE THE VEHICLE TO AN OPEN SPACE, WELL AWAYFROM BUILDINGS OF A CERTAIN HEIGHT- CONNECT THE SAT PROGRAMMER AND TEST TO MAKESURE THAT EVERYTHING WORKS PROPERLY BY MEANSOF THE APPROPRIATE FUNCTION (CONSULT THE RELATIVEMANUAL).GPSANTENNAHOW TO CONNECT THE GPS ANTENNAHOW TO FIX THE ANTENNA:- ON METAL PARTS WITHOUT THE USE OF THE DOUBLE-SIDEDADHESIVE MATERIAL (THE ANTENNA IS MAGNETIC)- ON PLASTIC PARTS USING THE DOUBLE-SIDED ADHESIVEMATERIAL SUPPLIED IN THE KITCAREFULLYCLEAN THEFIXINGSURFACEFig. 11OK OK OKOKNOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuantto Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions, may cause harmful interferenceto radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determinedby turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.Meta System S.p.A.Model: SAT RC 09FCC ID.: P3O97802This device complies with Part 15 of the FCC rules subject to the following two conditions:1) This device may not cause harmful interference.2) This device must accept all interference received, including interference that may cause undesired operation.
R&TTE Declaration Of Conformity (DoC) 0470We: Meta System S.p.A.with the address:Via Majakovskij 10 b/c/d/e 42124 Reggio Emilia –ItalyDeclareUnder own responsibility that the product:SAT RC 09To which this declaration relates is in conformity with the essentialrequirements and other relevant requirements of the R&TTE Directive(1999/5/EC).This product is in conformity with the following standards- Health & Safety (art.3.1) EN 60950-1 –- EMC (art.3.2) ETSI EN 301 489-1/-7/-19- Spectrum ETSI EN 301 511- Human exposure EN62311According to Directive 1999/5/CETechnical Director LasagniCesareReggio Emilia , 15/03/2010

Navigation menu