M3 Mobile MC-7100S M3 SKY, Industrial PDA User Manual

M3 Mobile Co., Ltd M3 SKY, Industrial PDA Users Manual

Users Manual

2FCC Information to User This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is con-nected.•Consult the dealer or an experienced radio/TV technician for help.
3FCC Information to User CautionModifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.FCC Compliance Information : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operationThe users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. In cases where the manual is provided only in a form other than paper, such as on a computer disk or over the Internet, the information required by this section may be included in the manual in that alternative form, provided the user can reasonably be expected to have the capability to access information in that form.
4FCC RF EXPOSURE INFORMATION In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96-326 adopted an updated safety standard for human exposure to radiofrequency (RF) electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies. The design of this MC-7100S complies with the FCC guidelines and these international standards. Use only the supplied or an approved antenna. Unanthorized antennas, modifications, or attachments could impair call quality, damaged your “MC-7100S ”, or result in violation of FCC regulations. Do not use the phone with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Please contact your local dealer for replacement antenna. This device was tested for typical body-worn operations with the back of the device kept 2cm from thebody. To maintain compliance requirements, use only belt-clips, holsters or similar accessories thatmaintain a 2 cm separation distance between the user’s Body and the back of the phone, including the antenna. The use of belt-clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. For more information about RF exposure, please visit the FCC website at www.fcc.gov.
5NotelThis manual is subject to copyright protection along with all relevant rights.lNo part of this document can be copied, reproduced, changed or translated in whole or in part by any means without prior written consent of M3 Mobile Co., Ltd. lThe content of the manual is provided “as-is” and be subject to change at any time without notice. lM3 Mobile Co., Ltd. makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. lMicrosoft, ActiveSync, Windows, Windows logos, Windows Mobile 5.0 logos are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries. Microsoft OEM products are licensed by Microsoft Licensing Inc., a entirely owned subsidiary of Microsoft Corporation. lAll other product names in this document or product are company names, trademarks or registered trademarks of the respective owners.
6Copyright and AgreementlThis user manual is provided “as-is”. It may contain editing error or omitting due to the difficulty of expressing technical feature. lIf an application program provided by other supplier using by M3 SKY, refer to the supplier for a program manual.lThe application program providers have the responsibility of indicating their contact number for customer service on M3 SKY terminal, item box, or program.lM3 Mobile Corporation do not warranty any programs produced and added by the third software companies after M3 SKY products are distributed from factories. lM3 Mobile Corporation has the right to ask warranty of any programs to the program providers to meet the needs of mobile networking companies. lThe contents in the user’s manual are protected under the Software Copyright Act. Copy, reproduction, distribution of the contents in the user’s manual without any written agreement notice of M3 Mobile Co. Ltd., is considered as criminal actions.lWindows, MS Office, Outlook, ActiveSync, Internet Explorer programs are the registered brand of Microsoft.lM3 SKY is the registered brand of M3 Mobile Co. Ltd. lThe brands of other products and service referred in this manual belong to corresponding providers.
7Caution when using M3 SKY (1)lUser Caution –When the unit is lost or stolen, notify to network provider immediately.–Do not rent the unit to third person without authorized permission. –Do not use the unit while driving. –For technical help, contact designated service centers. –Contact responding suppliers directly for questions on applications and work programs other than hardware and basic installed applications. –Use supplied adapter and accessories by M3 Mobile Co. Ltd.–Any defect on a unit while using other batteries, chargers and accessories can not get warranty. lCarrying and Storage Caution –Avoid to use the device under high temperature and humidity. It may cause fatality to the device.–Avoid intentional dropping from high elevation. It may cause fatality to the device. –Charge batteries fully before the first time use of the device.
8Caution when using M3 SKY (2)lDo not reconstruct –Do not reconstruct M3 SKY for any purpose. –It may cause fire in the unit, and wound or electric shock to users. –Any defect caused by reconstructing units, can not get warranty.lIllegal copy of mobile phone is prohibited–The person who reproduces mobile phone and uses this mobile phone is considered as criminals.–The use of lost or stolen mobile phone is considered as a criminal act. –Keeping the lost or stolen mobile phone after turning power off, is considered as a criminal act.
9Used frequency bandWCDMA : 2100 / GSM 850 (TX) 824 ~ 849 MHz / (RX) 869 ~ 894 MHz WCDMA : 1900 / GSM 900 (TX) 880 ~ 915 MHz / (RX) 925 ~ 960 MHzWCDMA : 850 / GSM 1800 (TX) 1710 ~ 1785 MHz / (RX) 1805 ~ 1880 MHzGSM 1900 (TX) 1850 ~ 1910 MHz / (RX) 1930 ~ 1990 MHzWLAN : 802.11b/ 802.11g (2412~2462MHz)B T : 2402~2480MHz Band width 200 KHz (GSM) / 5MHz (3G) External appearance 78.6 x 163.5 x 24.9mm (Width x length x height)Weight 320gOperationalTemperatureMain body -10 ℃~ +50 ℃Adapter -10 ℃~ +50 ℃Relative Humidity 5% ~ 80%AC Power Input : AC 100 ~ 250V, 50 ~ 60HzOutput : DC +5.2V, 3.0ASize and FeaturesSupported Frequency Bands can differ depending on the supplied antenna.
10ContentsCONTENTSlNote 2lCopyright and Agreement 3lCaution when using M3 4lSize and Features 61. M3 Introduction 9Product Composition 10Name and function of each part 12Input Buttons 13Soft/Hard Reset 15How to use stylus pen 16LED/Battery attaching/detaching 17Charging 18How to connect to PC 192. Basic Usage 20Calibration 21Main screen 23Input screen 243. ActiveSync 29ActiveSync Introduction 30Installing ActiveSync 31Synchronization of data 32
11CONTENTS4. How to use internet 33Via HSDPA 34Via Wireless LAN 36Via Wireless WLAN 39Browsing the Web Site 425. How to use the Phone 47Init Screen 48Phone Control 49Phone call and receive 50Phone book 51SMS send and receive 52Phone function 54Phone setting 55Contents6. Usage of Device 56Camera 57Bluetooth 61BTexplorer 66IrDA 69GPS 70Scanner 72RF-ID 78
121. IntroductionProduct CompositionName and Function of each partInput ButtonsSoft/Hard ResetHow to use Stylus penLED Battery Attaching/DetachingChargingHow to connect to PC
Product Composition (1)lAt the first time of opening the product box, please check if it contains all the basic components, listed as following.IntroductionM3 SKY main terminal + 2 units of standard battery Cradle + USB cable CD + ActiveSync 4.xEar Mic Phone + 2 units of Stylus penPortable Adapter13 The product components may differ depending on the supplied products.
lHow to use the manual–This manual provides detailed information to make using the device easier and faster.–The content related to phone or communication in this manual is only applicable when the device is equipped with HSDPA module for Voice and Data communication.–The features described in this manual can not be used when it is not equipped in the device (WWAN, WLAN, Bluetooth, IrDA, Scanner, Camera, GPS). –The content of this manual is subject to change without prior notice due to product improvement or modification of its functions, etc.Product Composition (2)Introduction14
Name and function of each partIntroduction15Volume ButtonAntennaScanner ButtonabBattery LockBatterydInfrared CommunicationPort (IrDA)Key PadCharge & USB/serial portLower (Cradle) useCharge Ramp (Left)HSDPA StatusRamp (Center)Scanner Ramp (Right)LCD touch ScreenReset SwitchPistol Grip Connecterd, ecStylus PenaBarcode Scanner WindowbMini SD Extension SlotEar Mic PlugcFlashCameraeSIM Card SlotCamera ButtonBattery(built in)
Input ButtonIntroductionFunction buttonDirection ButtonStart buttonPower buttonInput keysAlphanumericbuttonPhone/Call button End buttonLeft, rightfunction buttonBackspace buttonReturn button16Volume Button Scanner ButtonCamera Button방향 버튼Start / End buttonInput keysPhone/Call buttonLeft, right function buttonPower buttonBackspace buttonReturn buttonDirection Button
Component DescriptionPower buttonPress to toggle the device on/off.Long press to menu (Backlight, Display, etc) Function Phone/Call function press to accept the call or to execute the phoneEnd function press to hang-up/reject the call.Input keys Press to input alphabet characters or numbersLeft, right function button press to lunch an assigned application or functionAlphanumeric press to switch between alphabet and number inputStart button Press to display the Start menu.Backspace button press to move backFunction button press to Function Key with (*, 0, #)Direction button press to move left,right and up,downReturn button press to confirm the actionScanner button Press to launch the barcode data scan applicationCamera button Press to launch the Pictures & VideosVolume button Press the top key to increase volume, press the bottom key to decrease volume.Input ButtonIntroduction17 Some key functions might not be supported, depending on the option.
lSoft Reset- A soft reset allows your device to get a fresh start,similar to rebooting a computer. - This restarts your device and adjusts memory allocation. - All records and entries are retained after a soft reset.- Unsaved data in open programs may in some cases belost.18IntroductionSoft/Hard Reset① ② ③Press ①+②and ③power buttonlHard Reset- A hard reset removes power to your device. - This erases all records and entries, deletes all additionalprograms you have installed, and restores the device’s defaultfactory settings. - Never perform a hard reset unless a soft reset does not correctyour problem. lTo perform a hard reset :àPress the power button for more than 12 seconds to turn off the power (can be confirmed by LCD off)àWhile pressing call and end button, please press the power button shortly. àWhen the [CLEAN BOOT WARNING] window will pop up with message “All data will be lost! Do you want to continue?”“1. YES 0. NO, please press 1 to perform the Hard Reset.Please mind that you need to set up the standard timezone date, and time. After power off.
19How to use Stylus PenIntroductionlLong PressLeave Stylus pen touching the screenfor long and you can select the menuon the pop-up screen. You can also select functions availablein the designated item using the pop-up menu. The function of the pop-upmenu can be different according tothe program.lDragIt is used when you select the text. Please drag the desired part with stylus pen attached on the screen.lTapTap the touch screen one time using a Stylus pen to select and execute items and files.
20LED / Battery attaching/detachingIntroductionlLED Alarm–Informs Charging, Scanner Status. Type LED Status DetailsLED for chargingRedGreenChargingCharging completeWWAN Status LEDBlue BlinkingBlue OnBlue OFFWWAN Standby (within range of phone/internet)WWAN in use (phone/SMS/internet in use)WWAN is off or out of rangeScanner LED Green When the barcode data is successfully readlBattery attaching/detaching–Attaching BatteryAs picture shown, put the battery pack to back of PDA, and lock the battery pack with locking device. –Detaching BatteryPress locking device to the right, then using upper notch, detach the battery from main body.
21ChargingIntroductionlConnect plug-in from charger to charge jack of main body, or charge jack of cradle, and then place main body onto cradle.lCharging LEDlWhen charging, the status of the battery attached to main body can be confirmed by the LED left of upper corner of main body. Also the status of Sub-battery can be confirmed by the LED right of low corner of Cradle.Type LED Status DetailsDirect charging to main bodyRedGreenChargingCharging CompleteCradle Charging(Extra battery charging)RedGreenChargingCharging CompletelCharging in CradlelCharging using portable adapterSeparate BatteryMain body Charging LEDSeparate BatteryCharging LEDDo not use any other charger except one (5.2 V / 3A) provided . Make sure to handle it gentle; damage with excessive force may cause no warranty.Risk of explosion if battery is replaced by an incorrect type.Dispose of used batteries according to the instructions.When attached battery is completely discharged, plug charger to main body, then reset thedevice to check if screen is back on. To use, do at least 10 minute charging.
22How to connect to PClA cradle of M3 SKY supports charging and USB connection.lConnecting step of cradle of M3 SKY is as following.–Connect charger to USB cradle. (24pin connector)–Connect charger to power source. (to wall) –Connect USB cable of USB cradle to USB port of desktop PC. –Place M3 SKY onto docking cradle then execute Synchronization with Desktop PC.lThe location of USB port can be at the back, front or side of PC and the shape of USB port is identical on Desktop PC and Notebook.lUSB host function is available by putting USB cable into USB port of Cradle. Connecting to CradleUSB Host/ClientAC PowerUSB Host/Clientchangeover switchHCIntroduction
232. Basic UsageCalibrationMain screenInput Screen
lCalibrate the touch screen as shown below, at first time use or when cold (hard) booted.24Calibration (1)Basic UsageTap the screen one time witha Stylus penTap the (+) mark with the Stylus pen as it moves around.You can see the screen howto use the Stylus. If youdon't need it, click the Skip.①Press and hold the Stylus pen on the screen then select the Cut on the pop-up menu.②Press and hold the Stylus pen like the arrow on screen, Tap the Paste on the pop-up menu.③When all processes are complete, click the Next.① ② ③
lCalibration continue....25Basic UsageCalibration (2) Set up the standard time zone date, and time.To set up a password, tap 'Next' otherwise tap 'Skip'.To set up a password set up a password type and password.You can see the screen above after the Calibration.Choose outlook e-mail to set up an e-mailaccount and then tap the 'Next'. (POP3/IMAP/Outlook/E-mail)If you choose outlook E-mail or POP3/IMAPand then tap the 'Next', you should set up it Step by step.
Main Screen lMain screen–Main Screen is set below26Basic UsageStart menuDay/Time infoWireless infoUser infoInfo barMessages infoTask infoToday infoLock infoPocket MSN infoLeft / Right function infoButton functionStart menu Select the program you want to use.Info bar View the power, modem, sound, input mode and connecting view.Day/Time info View the current date and time.Wireless info View the Wireless power and state.User info View the personal information.Messages info View the Messages received.Task info View the task information.Today info View the Today’s information.Lock info View the screen / Lock information.Pocket MSN info View the Pocket MSN information.Left/Right Function info View the Left / Right information.
lTo use Input- Process this program " Start > Programs > Word Mobile".lTo use the Keyboard Input27Basic UsageTap the arrow next to the keyboard icon and then select the keyboard on the menu screen as a picture above.This is the Keyboard Input Screen.You can input the letter, numberand characters when you clickthe each icon on the keyboardInput screen.Input Screen (1)
lUsage of Block Recognizer input.28Input Screen (2)Basic UsageTap the arrow next to the keyboard icon and then select theBlock Recognizer on the menuscreen as a picture aboveIt is the screen of block recognizer input.In this input screen you can input letters in 'abc' and numbers in '123 ‘each in the input box seen on thescreen.In the input screen of block recognizer you can input specialletters and characters by tappingthe input box once.
29lUsage of Letter RecognizerInput Screen (3) Basic UsageSelect the arrow next to the keyboard icon and then Select the'Letter Recognizer' on the menu screen as the picture above.This is the 'Letter Recognizer' screen.In the ‘Letter Recognizer' input screen, you can input the capitalletters in 'ABC', the small lettersin 'abc' and numbers in '123' each in the input box seen on the screen.Please choose ‘Options…’ on the input menu. Select ‘Letter Recognizer’ as input method andthen click ‘Options…’. Here you can configure theinput modes.
30lUsing transcriber input–Transcriber is a writing recognizer program. It provides you various writing input and input menu.Input Screen (4) Basic UsageSelect the arrow next to the keyboard icon and then select theTranscriber on the menu like thepicture.This is the Transcriber input screen.If you input letters, numbers and characters on the screen with the stylus pen, it would be written automatically on the place where the cursor is blinking. You do not have to concern about the inputbox when using transcriber.
31lInput by using Keypad–You can input numbers and letters by using Keypad. Input Screen (5)Basic UsageConvert ‘1 ,A, a’ using the input convert buttonon the input screen as the left picture. Then youcan input capital letters, small letters, numbersand characters using keypads.For example, in the case of inputting the M3SKY, Convert to ‘a’ > Keypad 6 > convert to ‘1’>Keypad 3 > Convert to ‘A’ > Keypad 7(4 times)> Keypad 5(twice) > Keypad 9 (3 times)By pressing ‘*’, ‘0’,’#’ while ‘Fn’ button ispressed, you can apply ‘Space’, ‘Enter’ and ‘OK’function respectively.Pressing ‘Fn’ Key will change the function modein following order : ‘Fn’ one time mode -> ‘Fn’hold mode -> ‘Fn’ disable modeAlphanumeric buttonInput Key buttonFunction button
3. ActiveSyncActiveSync IntroductionInstalling ActiveSyncSynchronization of Data
ActiveSync IntroductionlSync is an abbreviation of “Synchronization” and refers to the process of making data in PDA and desktop computer to be same by linking both data.–Sync is an abbreviation of ‘Synchronization” and refers to the process of making data in PDA and desktop computer to be same by linking both data. When either PDA or PC modifies data, it updates others to the most recent data. –Not all the data is synchronized at same time. It follows the option settings of ActiveSync, provided by Microsoft.lBy linking M3 SKY and computer, you can make data in both devices in the same status (synchronization) or install, copy, move, delete programs for business purpose and others. lIt is compulsory to install this program in order to install business programs, synchronize data, back up and synchronize contact numbers in an address book, etc.Do not connect USB of Cradle to desktop PC before installing Active Sync to desktop PC..It may cause a desktop PC cannot recognize PDA since Active Sync contains PDA program driver. 33ActiveSync
34lTo install ActiveSync- Select the ActiveSync program in the CD provided, and then install it to the computer.–Once the installation is complete, connecting window will start. Connect the cradle with PC using USB cable, and then dock the device on the cradle. –When the device is recognized on the PC, Connection will be established after assigning the port for it automatically. lThe definition of Partnership–It is the process of paring PC with PDA in order to exchange the data each other. Via this process, the data on the PC and on the PDA can be synchronized.※The synchronization is available with Outlook 2003 or above version. It is not supported on the outlook express which is provided together with Windows OS. ActiveSync install / connectActiveSyncPlease re-try the synchronization if connection is disturbed by strong noise or static. –To install ActiveSync on the host computer, download version 4.1 or higher from the Microsoft web site at http://www.microsoft.com. Refer to the installation included with the ActiveSync software.–Microsoft recommends installing ActiveSync on the host computer before connecting the mobile computer.USB connection to PC
35ActiveSyncSynchronization of DatalIf you see the Microsoft ActiveSync window in the desktop PC, you can find an option icon. If you click this option icon, taps such as “Sync Options”, “Sync Mode”, “Rules” will appear. l“Sync Options” is a menu that you can select an item to synchronize.–Contact, Calendar, E-mail, Tasks, Memo, Favorite, Files, Media, etc. l“Sync Mode” enables you to choose synchronization methods. According to the selected synchronization mode, there are 3 following methods: –Continuously while the device is connected: In this mode, if you want to carry out synchronization, connect the device to thedesktop computer. ActiveSync will immediately start synchronization and synchronize according to the user’s input of changes in a computer or the device.–Only upon connection: If you want to carry out the synchronization after the first synchronization on a manual basis, click Sync.–Manually: In this mode, ActiveSync will not run automatically. In order to carry out synchronization, click Sync.lSynchronization is the process of updating M3 and desktop PC after comparing their data. Any files including personal organizer management data, etc in M3 can synchronize with those in the desktop PC.When Troubleshooting the ActiveSync, Check the solutions below.lEnsure the correct USB cable is used in the cradle with USB port of the PC.lEnsure the power input cable of M3 Sky or LCD.lPlease re-try the Synchronization after Soft-reset or Hard-reset. Finish the running program and save the data for sure before resetting.
Via Wireless WANVia Wireless LANBrowsing the Web Site4. How to use Internet
Via HSDPA (1)How to use InternetlTo connect to the Internet via Wireless WAN (1)Tab ‘Start > Settings > Connections’ Select ‘Add a new modem connection’ of ‘My ISP’ in the ‘Connections’.Put the name you want into the‘Enter a name for the connection’. Then select the ‘cellular Line(GPRS)’ in the ‘Select a modem’.37WWAN service is optional.It is not available in the device which does not have WWAN module installed.
lTo connect to the Internet via Wireless WAN (2)38Via HSDPA (2)How to use InternetInput the Access point name suitable to the SIM Card / Operatorcompany of Network then Tab the‘Next’.Tap the ‘Finish’ after input the User name and passwordaccording to the setting.(In some cases, it is required toset IP address at the advancedmenu.)Select the ‘Manage existing connections’ on the Connections. Choose the ISP which you want to connect to as picture above.* The saved settings automatically appliedat connecting.You can explore the Internet using WWAN connection.
39Via Wireless LAN (1)How to use InternetlYou can use the Wireless Network Via Wireless LAN. lM3 SKY supports IEEE 802.11b and 802.11g. lTo connect the Wireless LAN (AP must be on and functioning)Wireless LAN is optional. You can only use WLAN, when the WLAN module is built in to the device. On the Today Main screen, you selectWireless state bar or go to ‘Start > Settings > Connections>’ Wireless Manager. Tap the WI-Fi on the ‘Wireless Manager' to turn WLAN on.When the dialogue box is appeared, Select the AP you want andthen, you can connect the Network with it. To connect directly on the Main Screen
lTo connect via Wi-Fi menu40Via Wireless LAN (2)How to use InternetOn the settings screen, you select Wi-Fi Icon. You can also tap Start > Settings >Connections>Wi-Fi. Configure the connect type thenclick the 'Next'. Configure the connect type then click the 'Next'.Input the authentification data then clickthe 'Next'.After configure Network authentification, tap the 'Finish'. You can see the wirelessNetworks available.
lContinue from the last page–Configure DHCP / Static IP41How to use InternetVia Wireless LAN (3)Tap an adapter to modify setting on the wireless LAN card and select the 'Edit'.If you configure the IP as DHCP, Click the 'Use Server-assigned IP address.If you configure the IP as Static, Click the 'Use Specific IP address.
42Via Wireless WLAN (1)How to use InternetlYou can use the Wireless Network Via Wireless LAN. lMM3 supports IEEE 802.11b and 802.11g. lTo connect the Wireless LAN (AP must be on and functioning)Wireless LAN is optional. You can only use WLAN, when the WLAN module is built in to the device. On the Today Main screen, you selectWireless state bar or go to ‘Start > Settings > Connections>’ Wireless Manager. Tap the WI-Fi on the ‘Wireless Manager' to turn WLAN on.When the dialogue box is appeared, Select the AP you want andthen, you can connect the Network with it. To connect directly on the Main Screen
43lTo connect via Wi-Fi menuVia Wireless WLAN (2)How to use InternetOn the settings screen, you select Wi-Fi Icon. You can also tap Start > Settings >Connections>Wi-Fi. Configure the connect type thenclick the 'Next'. After configure Network authentification, tap the 'Finish'. You can see the wirelessNetworks available.
44lContinue from the last page–Configure DHCP / Static IPHow to use InternetVia Wireless WLAN (3)
45How to use InternetBrowsing the Web Site (1)lMicrosoft Internet Explorer- Via Wireless WAN , Wireless LAN and Active sync connection, you can browse the web.- You can download programs and files by accessing the Internet.To use the Internet ExplorerTap 'Start > Internet Explorer This is the Internet Explorer processing screen.Address WindowSearchingInput the address you want on the address window in upper of the screen, thenclick the 'search'. It will try to connect to that web address via Wireless networkthat is connected.
lContinue from the last page.46How to use InternetBrowsing the Web Site (2)On the 'Menu > Favorites...' you can see the list of sites that you have saved and browse to it directly. The favorite page is like the picture above.On the Menu > History... You can see the list of sites that you haverecently visited. The history page is like the picture above.See the 'Start > Help' if you want to know more about how to use the Internet Explorer
lTo set up an e-mail account 47How to use InternetBrowsing the Web Site (3)Process the 'Start > Messaging'. Select the'Menu > Tools > New Account...in the outlook E-mail box.Set an E-mail provider for 'other‘then tap 'Next.'Input the E-mail address on theEnter e-mail address , then tap ‘Next '.When the Status is for completed,tap the 'Next'.
lContinue from last page48How to use InternetBrowsing the Web Site (4)Set an E-mail provider for 'other‘then tap 'Next'.Select the Account Type and putthe Name then tap 'Next'.Input the 'Incoming mail, Outgoingmail, Domain' then select 'Finish'.* For detailed setting menu, pleaseclick ‘Options’.After finishing the setting you can send andreceive E-mail using the e-mail account.
lTo send and receive an E-mail49How to use InternetBrowsing the Web Site (5)< To receive an e-mail>Select the 'Message' on the 'Today'Select the 'Send / Receive' in the 'Menu' and check the received mail.<To send an e-mail>After process the 'Message' program , select the 'New' . You can send an e-mail when you select the 'Send' after writing a newe-mail.
505. How to use the PhoneInit ScreenPhone ControlPhone call and receive Phone bookSMS send and receive Phone functionsPhone setting
Init Screen51How to use the PhonelPhone Main ScreenGSM OperatorNetwork TypeHSDPA / Network StatusVolumeCall StatusInput NumberKey PadContactsPhone MenuGSM Operator It indicates the current Network Provider.Call Status It shows Call Status.Input Number It shows Inputted Numbers.Key Pad It is used to dial the number and can be used as speed-dial.Contact It shows Phone Book Dialog.Network Type It displays the availability of GPRS and EDGE / HSDPA connection.GSM/Network Status It indicates the signal strength.Volume It is Volume on/off and vibratePhone Menu Talk, End, Speed Dial, Call History, etc menu…
lPhone Program On/Off52Phone ControlHow to use the PhoneYou can turn on and off phonein Wireless ManagerlPhone Call Send/EndSEND ENDTap the Phone button on the left bottom of the Today Screen and then you can process thePhone program. Also you can finish the programusing the X button.Select the SEND and END button likethe picture above to start and finishthe Phone program.
lPhone Call53How to use the PhonePhone Call and Receive To make a call:1.Input number via program keypad or device keypad.2.Make a call by pressing the ‘Talk’button on the program, or pressing‘SEND’ button on the device.To hang up:Press the ‘END’ button on the program or on the device.lPhone ReceiveWhen you get the Incoming Call, you can receivethe phone call tapping the Answer button. If youdon’t want to receive it just tap the Ignore button.
PhonebooklTo use Phonebook54How to use the PhoneSearchingA name orNumber.Contacts Menu Contacts OptionSearching Contacts You can search the contacts by writing the name and number or tapping.ContactsMenuNew Contact Input the new contactNew SIM Contact Input the contact to the SIM Card.Send Contact Transmit the information of Contact by BEAM or SMS.Copy/Delete Copy or delete the ContactOptions Set the Options for Contact.View By See the Contact by Type ( Name , Company, Number … )Filter Filter the information you want.ContactsOptionCall W/H/M Call by the number on the Contact.Send E-mail Send an E-mail by the address on the Contact.Send SMS Send SMS by the number on the Contact.Add to Speed Dial Add the number on the Contact to Speed Dial.Send Contact Send the information of Contact by BEAM or SMS.Copy/Delete Copy and Delete the Contact.
lHow to send SMS55How to use the PhoneSMS send and receive (1) Select ‘message information’ menu on the main screen to send SMS. You can also send SMS by selecting ‘SMS send’ menu on Contacts or anyother applications.Change to the ‘Text Messages’ on the Message Program like the picture above and tap the ‘New’ on the bottom.Input the phone number and message. Tap the send to sendSMS.You can see the pop-up screen when SMS is sent successfully.
lHow to receive SMS56How to use the PhoneSMS sent and receive (2)When connected to the GSM network, new message arrival will be alerted apicture above.By tapping one of the received messages, thecontent will be displayed on the separatewindow as picture above.Controlling received SMS can be done by using the menu on the ‘New Text Message' alert window or on the Text Messages program.
Controls while on the phoneFunctions while on the phone57How to use the PhoneYou can use various functions when you select the button on the bottom while talking on the phone.You can see the list of recent calls by selecting ‘Call History’.You can take a memo While talking on the phone by selecting the Note.KeypadChange to Mode available to input the Number on the screen.MuteSetting for receiver not to hear my voice while on the phone.Hold Hold for a moment while on the phoneContact Move to ContactEnd End phone callFeatured functions while on the phone
Phone settingPhone setting58How to use the PhoneTap the ‘Start > Settings > Personaltap > Phone’ and in that menu you can set the Security and Sounds.Check the ‘Require PIN when phone is used’ check box when PIN lock isrequired.Tap the ‘Start > Personal Tab > Phone > Network’ to set an information related to the Network.( Change the Network ..)Tap the ‘Start > Personal Tab >Phone > Services Tab ‘ to set aninformation related to the Service.( In the Network or SIM )Call Barring Block the calling to the specific number.Caller IDTurn on or off the Caller ID function. If it is enabled, your number will be shown to the receiver. Call Forwarding You can forward the incoming call to the other number.Call WaitingYou can receive another call while you are talking on the phone.Voice Mail Text MessagesSet the SMS Service Center number and Voice Mail number.Fixed Dialing Limit the available phone functions using PIN2.Description of Service Menus
6. Usage of DeviceCameraBluetoothBTExplorerIrDAGPSScannerRF-ID
To use the Camera (1)lNotice before taking pictures- The camera equipped with the M3 Sky is supported 2 mega pixels.Usage of DeviceFunction Still Video CommentMode Normal, Burst, Timer N/A Setting for taking photoBrightness -3, -2, -1, 0, +1, +2, +3 Setting for BrightnessResolution QCIF, QVGA, CIF, VGA ,SVGA, SXGA, UXGA QCIF, QVGA Setting for sizeWhite Balance Automatic, Sunny, Cloudy, Fluorescent, Incandescent Setting for White balanceFlash Flash ON, Flash OFF Setting for Flash ON/OFFAF Trig AF Setting for Auto FocusCamera Program Processing ScreenCamera is optional. On the device with no built-in camera, Camera function can not be used.QCIF(176x144), QVGA(320x240), CIF(352x288), VGA(640x480), SVGA(800x600)SXGA(1280x960), UXGA(1600x1200)60
lTo process the camera program- You can process the camera program when you tap the camera button or tap the camera icon on the'picture or video'.To use the camera (2)Usage of DeviceSelect the 'Start > Programs > Pictures & Video. You can process the camera program when you select the camera icon on the Picture & Video or select the camera icon in the menu.61Tap the ‘Menu > Options … > Camera Tab’ and then you can set the route of the storage memory , name and quality. You can set the Video on the Video Tab.
lTaking a Still photoUsage of Device62Execute the camera program first. Move around to focus the desireditem. Finally press the camera button to take a picture.After executing the camera program , Preview mode will be changed to standby mode after certain amount of time. In order to start Preview Mode again, just tap the screen or press thecamera button.After taking a picture, the captured image will be displayed on the screen.If you want to execute the camera program, tap the camera button at thebottom or click the camera icon on the left of window.You can see the list of pictures taken previously by tapping ‘Thumbnails’ inthe Camera shooting mode.To use the camera (3)
lTaking videos63Usage of DeviceIf you want to take a video, select ‘Menu > Videos' after executing the camera program.While taking a video, you can either stop (by tapping stopbutton) or pause. (by tappingpause button)If you want to watch the video taken, Select the 'Thumbnails' firstto see the list of video files available.When you select the video you want, you can play the videorecorded.To use the camera (4)
lBluetooth On / Off64Bluetooth Communication (1)Usage of DeviceOn the 'Today Main Screen' , select the Wireless State bar or Tap 'Start > Settings > Connections and select ‘Wireless Manager’.Bluetooth is optional. Device without built-in Bluetooth can not use Bluetooth service.Bluetooth support the transmission and reception of files between the serial connecting service and Windows Mobile device.To turn on/off Bluetooth, tap the Bluetooth on the Wireless ManageThe status of Bluetooth can be seen on the wireless status bar on the main screen.
65lSetting the Bluetooth-On the Bluetooth setting screen, you can set the Mode, connecting to BT device and COM settingsUsage of DeviceYou can set the Bluetooth mode and establish connection when you tap the 'Bluetooth' icon on the Start > Settings > Connections.In the Mode tab, you can turn on/off Bluetooth and make visibleor invisible the device from outside.In the device tab, you can search and connect to other Bluetoothdevices.In the COM Ports tab, you canset incoming Port and outgoingPort.Bluetooth Communication (2)There are two ways that you can set up Bluetooth; StoneStreetOne/ Microsoft. -It can be changed by operating BT Select in the ’Settings > System’.-’StoneStreetOne’ is the way of using ‘BTExplorer’, and it is set up as the basic mode in the mobile.
lTo connect the Bluetooth- you can establish the connection by searching, matching pin code and selecting the service.66Usage of DeviceYou can search the Bluetooth deviceavailable when you select the 'Addnew device...' on the Device Tab.Select a device to connect with andtap 'Next' . Also you can selectthe 'Refresh' button if there is nodevice available.Enter a Passcode to establish a secure connection.The passcode can be fixed one or the one which is negotiatedbetween two parties in beforehand.It shows the service available on the Bluetooth device.It shows the registered devices.To add more device, please tab‘Add new device’.Bluetooth Communication (3)
lHow to make the serial connection via Bluetooth–It is possible to assign the registered device to the COM port.67Usage of DeviceOnce the device is registered, please tap ‘COM Ports’ tab and then select ‘New Outgoing Port’.Select the device you wand to addand tap 'Next'.Select the port which is available,and then tab ‘Finish’.Once the connection is made, youcan use the available service.Bluetooth Communication (4)
lTransferring files via Bluetooth connection.- It is possible to transfer files between Windows Mobile devices via Bluetooth.68Usage of DeviceIn order to transfer files via Bluetoothconnection, please go to 'Start > Settings >Connections > Beam‘ and then Checkthe 'Receive all incoming Beams ‘.Select the file you want to transfer in the File Explorer. Press the filename long and tab ‘Beam File’.By tapping ‘Beam File’, the list of available Bluetooth devicesshown. Please choose the device to transfer the file to.Bluetooth Communication (5)
69Usage of DeviceBTExplorer(1)lSet up Bluetooth using BTExplorer -The user can set up mode, connecting BT device, COM setting by using BTExplorer.If you click the ‘Bluetooth’ in the ‘Start> Settings> Connections’, you can set up and connect the Bluetooth mode.Use the Device Info tab to configure the M3 Sky’s Bluetooth connection modes.Use the Services tab to add or delete Bluetooth services.To add a service:1. Tap Add. The Add Local Service window displays.2. In the list, select a service to add.3. Tap OK. The Edit Local Service window displays for the selected service.4. Select the appropriate information and then tap OK. See the following sections for information on the availableservices.
70Usage of DeviceBTExplorer(2)lSet up Bluetooth using BTExplorer Security settings allows you to set global security policies for Bluetooth. Note that these settings are only active on local Services that are set to Authenticate or Authenticate/ Encryption. You can set authentication on local Services under the Services tab.Virtual COM Port defines which COM ports BTExplorer attempts to use for virtual COM ports. Check theappropriate checkbox to use the port as a virtual COM port. When finished, choose Apply to enforce changes, or Revert to restore the original settings.Use the Discovery tab to set and modify discovered devices.Use the Profile tab to load or remove Bluetooth services profiles. If a profile is not used, it can be removed to save memory.
71lConnect Bluetooth using BTExplorer– The user can access Bluetooth by searching, matching the password, and selecting the service.Press ‘BTExplorer’ in the ‘Start>Programs’Press ‘New Connection’ in the menu where’s at the bottom of the screenIt displays the service list you can set up. Set up your choice and press the ‘Next’.It displays the device list that you can connect. Click the device you want and press the ‘Next’.Usage of DeviceBTExplorer(3)
lTo connect via IrDAM3 Sky can communicate with desktop, notebook, pocket PC as well as other PDA that has OBEX protocol for the IrDAcommunication.To use infrared communication §Locate Infrared communication port to be in series with an infrared (IrDA) port with other device. §Press a quick link icon > Infrared communication menu.§Infrared communication program is started and you can exchange data.§If you want to have a serial communication with the device like printer, it is possible by connecting the COM Port.※It is advised to communicate within the shortest distance. Shorter distance makes data transmission faster. 72Usage of DeviceIrDA CommunicationIrDA Communication PortConnecting to IrDA PrinterFile transmission between PDAIrDA port is optional. Device without IrDA port can not use this feature.
lTo set the GPS–Tap the ‘Start > Settings > System Tab > GPS’ and then you can set the information related to the GPS.–You don’t have to set additional information when there is a single program which uses GPS data. Whenthere are more than one program which use GPS data, you need to set the program port and hardwareport required for each program.73Usage of DeviceTo use the GPS (1)Select the GPS on the System Tab. Set the GPS Program Port whichis not yet used.Set the Hardware port of the device.GPS hardware port for M3 sky isCOM2 and with baud rate of 9600.GPS is optional. GPS feature is not available on the unit with no GPS module integrated.
lTo Connect the GPS- When there is a single GPS program, please use the GPS hardware port (COM2). When there are morethan one GPS program, please use the pre-defined GPS program port.74Usage of DeviceTo use the GPS (2)Execute the GPS program you want. Set the COM Port and Baud Rate. It is available to use various application using GPS like searching the current location. Sample GPS map is not provided by M3Mobile.
To use the Scanner (1) Scanner ManuallTo scan the barcode, there are two scanner programs installed on the device1. M3 ScanTest-It is a sample test program. It is only for testing the scanning feature of the device.It can not be used for business application.2. ScanEmul-It is a program which can be used to output the scanned data on the application.(like MS Word-Pad, Internet Explorer or Business Application)- The ScanEmul program must be running if you want to scan barcodes.Usage of Device75
lThis program is located under Flash Disk -> Scanner folderThe Scanned Data will be displayed hereYou can get the information like Firmware version,DLL version and Decoder version.It is to trigger the scan beam. You can also Use ‘S’ button on the right side of Deviceto trigger it.You need to select this tab to configure SettingsUsage of Device76To use the Scanner (2) M3 Scan Test
Usage of Device77To use the Scanner (3) Scan EmulWhen Scan Emul program operates, program icon is appeared in the tray bar.The user can access the various menus using this icon.When you click the barcode icon, you will get This menu popped up.
You can set the Reading Option.Sync: Scan Beam shoots until the Barcode is scanned or it’s timed outAsync: Scan Beam Shoots while trigger button is pressed or until it’s timed out.Security Level: number of times to check scanned data.(ex, when it is set to 2, it will scan two timesand compare the data whether it is same or not.Time Out: Scanner beam will be shoot for this time set.Sound: you can choose the sound which will ring when the datais scanned.Output: you can select the output method.When it is checked Enter code will be inserted after the barcode data.Usage of Device78To use the Scanner (4) Scan Emul
79Usage of DeviceTo use the Scanner (4) Scan EmulYou can select the symbol (Symbology) to activate.You can create the prefix and suffix that will be used in the beginning and ending of the bar code data.You can set the button that will be used as the scan button.
80Usage of DevicelHow to use scanner–Usage of 1D Scanner (MC-7100S, MC-7500S)–Usage of 2D Scanner (MC-7700S)Correct way Incorrect wayScanner is optional. You can not use scan feature with no scanner enabled device. 2D Barcode Scanner is optional. Only with 2D Barcode scanner enabled device, you can do 2D barcode scan. (MC-7700S) Correct way Incorrect wayTo use the Scanner (6) Scan Test
To use the RFID (1)81lTo Connect the RFID–Tap the ‘Start > File Explorer > Flash Disk > RFID’and then you can run RFID.Usage of Device
To use the RFID (2)82lTo Connect the RFID–Let the upper back of the terminal touch the tag and then tap READ. RFID reader located in theupper-back of the terminal will recognize the tag.–You can select Read Mode in Option. In Sync mode, the terminal should reach the tag to read theinformation. In Async mode, the terminal automatically search around and read the tag.In Continuous mode, the terminal continues to read the tag unless you command to stop.Note that Continuous mode consumes the battery faster.You can select Read Mode in Option.Usage of Device
To use the RFID (3)83lSupport TagRF-ID is optional. Device without RF-ID can not use this feature.Frequency supported only 13.56MHzUsage of Device

Navigation menu