Lutron Electronics 0107 In-wall Dimmer User Manual

Lutron Electronics Company Inc In-wall Dimmer

User Manual

Installation InstructionsPlease Read Before Installing0301742 Rev AGrafikTT1. CAUTION: To avoid overheating and possible damage to other equipment, do not use to control receptacles, fluorescent lighting fixtures, motor-operated appliances, transformer-supplied appliances, or electronic low-voltage lighting fixtures.2. Install in accordance with all national and local electrical codes.3. When no “grounding means” exist in wallbox, the NEC® allows dimmer without a grounding connection to be installed as a replacement if 1) a nonmetallic, noncombustible faceplate is used with nonmetallic attachment screws or 2) the circuit is protected by a ground fault circuit interrupter (GFCI). For this type of installation, cap or remove the green ground wire on the dimmer, and use an appropriate wallplate, such as a Lutron® GrafikTTM series wallplate.4. GrafikTTM dimmers are not compatible with standard 3-way switches. Use only with companion dimmers (GT-AD-S or GT-AD).5. Companion dimmers (GT-AD-S or GT-AD) cannot be used individually but must be used in conjunction with a GrafikTTM dimmer in a multi-location application.6. In any multi-location circuit, use only one GrafikTTM dimmer with up to four companion dimmers.7. GrafikTTM dimmer settings such as Light Bar Intensity and Speaker On/Off can be modified using Advanced Programming Mode. For instructions and information on how to use Advanced Programming Mode, please visit www.lutron.com/grafikT or call Lutron® Technical Support at 1.800.523.9466.Lutron Electronics Co., Inc.7200 Suter RoadCoopersburg, PA 18036-1299InstallationImportant NotesCompatible LEDsDimmers LED Incand. / Halogen Hi-lume® A-Series LTE LED Drivers GTJ-150 150 W600 W—GT-150 150 WGT-250M 250 W350 W8 maximumGTJ-250M 250WRRT-25CL 250 WHQRT-25CL 250 WCompanion dimmersGT-AD-S For use with HQRT-25CL and RRT-25CLGT-AD For use with all other models120 V~ 60 HzCree®: 499485; CR6X-PP2Philips®: 426122(9290002330)(822580)(bc=046677426125)EcoSmart®: ECO-575L Sylvania®: 78390 (LED8R20/DIM/SE/830/RP)FEIT (Utilitech): PAR38/LEDG5For a complete list of compatible LEDs, please visit: www.lutron.com/LED1.800.523.9466 U.S.A. | Canada | Caribbean +1.888.235.2910 Mexico+1.610.282.3800 Others www.lutron.comMulti-location - Lights can be dimmed from multiple locations.One location will be replaced by a GrakTTM dimmer and the other location(s) by a GrakTTM companion dimmer. The dimmer can be wired on the line-side or the load-side.DimmerConnect the green ground wire on the dimmer to the green or bare ground wire in the wallbox (See Important Note 3 at left).Connect tagged wire removed from the switch to the black wire on the dimmer. Connect one of the remaining wires removed from switch to the red wire on the dimmer.Connect the remaining wire removed from the switch to the blue wire on the dimmer.Companion DimmerConnect the green wire on the dimmer to the green or bare ground wire in the wallbox (See Important Note 3 at left).Connect the same color wire connected to the red wire on the dimmer to the red wire on the companion dimmer, along with the tagged wire.Connect the remaining wire to the blue wire on the companion dimmer.6aGanging and DeratingWhen combining controls in the same wallbox, derating is required. No derating is required for companion dimmers.1 Designed for use with permanently installed LED, incandescent, or tungsten halogen only. Control 1Load Type Not Ganged End of Gang Middle of GangGT-150GTJ-150LED 150 W 150 W 150 WIncand. / Halogen 600 W 500 W 400 WGT-250MGTJ-250MRRT-25CLHQRT-25CLLED 250 W 250 W 250 WIncand. / Halogen 600 W 500 W 400 WLutron® Hi-lume® A-Series LTE LED Driver350 W, 8 drivers max350 W, 8 drivers max350 W, 8 drivers maxAdditional InformationTechnical AssistanceFor warranty details, please visit: www/lutron.com/warrantyFor FCC/IC information, please visit: www.lutron.com/fcc-icLutron is a registered trademark and FASS and GrakT are trademarks of Lutron Electronics Co., Inc. NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts.© 2014 Lutron Electronics Co., Inc.IMPORTANT Cap the blue wire with the blue connector. This wire does not get connected.IMPORTANT Wire connectors provided are for copper wire only. For aluminum wire, consult an electrician. English341! WARNING! Shock Hazard. May result in serious injury or death. Turn off power at circuit breaker before installing the unit.Single-pole - Switch will be replaced by a dimmer. Connect the green ground wire on the dimmer to the green or bare ground wire in the wallbox. (See Important Note 3 at left.)Connect the black wire on the dimmer to one of the wires removed from the switch. If you had taped together two wires (see step4), connect both wires to the black wire on the dimmer and remove the tape.Connect the red wire on the dimmer to the other wire removed from the switch.289710Tag56Remove wallplate and the switch mounting screws. Leaving all wires attached, carefully pull the switch out from the wall.Identify switch type. Single-pole – The switch will have insulated wires connected to two screws of the same color plus a green ground screw.Multi-location – 3-way switches will have insulated wires connected to three screws plus a green ground screw. One of the wires is connected to a screw of a different color (not green) or labeled COMMON. Tag this wire. The switch may have two wires attached to the same screw. Tape these two wires together before disconnecting. Proceed to disconnect the wires from the switch. Remove wallplate from the GrakTTM dimmer and any companion dimmer, but leave wallplate adapter connected.Install dimmer and/or companion dimmer.6bBlack Tag Live BlueNeutralGreen GreenDimmer Companion Dimmer LightRed RedDimmer Line-SideTag Black LiveNeutralBlueGreen GreenRed RedDimmer Load-SideTag Ta g Companion Dimmer Dimmer LightCarefully push wires into the wallbox. Install dimmer/companion dimmer(s) and snap on wallplate. Associate GrakTTM dimmer to Clear Connect® devices (GTJ-models only). Press and hold the Toggle button on the GrakTTM dimmer for approximately 6 seconds. Once all of the light bar LEDs begin to ash, release the Toggle button.Press and hold the appropriate button on the device (see pictures below) for approximately 6 seconds.Once the dimmer associates the recently added devices, the LEDs and load will ash 3 times and the GrakTTM dimmer will exit set-up mode.Turn ON power at circuit breaker.Turn OFF power at circuit breaker.If needed, set low-end trim. See Dimming Operation section (at lower left) for details. Dimming Operation Adjust• Touch to set lights to desired level• Slide to adjust light level Toggle• Touch to turn Off or to turn On to previous light level• Toggle button is white when On, orange when OffFASSTM - Front Accessible Service SwitchNote: FASSTM is not available on companion dimmers.IMPORTANT NOTICE: FASSTM - Front Accessible Service SwitchTo replace bulb(s), power may be conveniently removed by pulling the FASSTM down on the dimmer. After replacing bulb(s), push the FASSTM back up fully to restore power to the dimmer.For any procedure, other than routine lamp replacement, power must be turned OFF at the main electrical panel. Set High-End Trim: 1. Press and hold top of light bar (approximately 5 seconds) until Toggle button flashes orange. 2. Slide finger on light bar to adjust to desired brightness. 3. To exit, press and hold the Toggle button (approximately 5 seconds) until the Toggle button stops flashing. Set Low-End Trim: 1. Press and hold bottom of light bar (approximately 5 seconds) until Toggle button flashes orange.2. Slide finger on light bar to adjust to desired brightness. 3. To exit, press and hold the Toggle button (approximately 5 seconds) until the Toggle button stops flashing.TroubleshootingSymptom Possible CauseLight does not turn On and no LEDs turn On.• The FASSTM on the dimmer is pulled down to the Off position.• Light bulb(s) burned out.• Breaker is OFF or tripped.• Dimmer is miswired. Check wiring.Unit is non-responsive. • Cycle power to unit by pulling the FASSTM down and back up to fully restore power.Light turns On and dimmer works, but companion dimmer does not work.• Wire connected to the blue wire on the dimmer is not the same wire connected to the blue wire on the companion dimmer. Check wiring.• Wire connected to the red wire on the dimmer is not the same wire connected to the red wire on the companion dimmer. Check wiring.Lights repeatedly turn On and Off.• Load is less than the minimum load. See the Minimum Load Chart to determine the acceptable minimum load.Lights are ickering or exhibiting poor dimming range.• Set low-end trim. See Dimming Operation for details. Minimum Load Chart1 For performance or compatibility information, Lutron recommends visiting our website www.lutron.com/LED, which is constantly being updated.Load TypeApplication Number of Companion Dimmers LED 1Incandescent / HalogenSingle-pole 0 2 LED lamps 40 WMulti-location 1 3 LED lamps 80 WMulti-location 2 4 LED lamps 120 WMulti-location 3 5 LED lamps 160 WMulti-location 4 6 LED lamps 200 WGroundDifferent-colored screw120 V~60 HzBlack GroundRedBlueGreenNeutralLiveDimmerLightGroundOccupancy / Vacancy SensorDaylight SensorOLUTRONPico® Wireless Controller

Navigation menu