Lutron Electronics 0095 Roller Shade User Manual

Lutron Electronics Company Inc Roller Shade

user manual

Roller Shade• Installation and Setup Guide—Please Read Before Installing and OperatingBattery Powered Window Shade with RF Wireless Remote ControlLutron Electronics Co., Inc.7200 Suter RoadCoopersburg, PA 18036-1299, U.S.A.09/2013P/N 045404 Rev. ALutron, O, Serena and Pico are registered trademarks of Lutron Electronics Co., Inc.Equal depth both sidesA 1 Mounting the shade rail: 3 Hanging the shade: 2 Installing the end caps on optional fascia: 2.1 Press-fit an end cap on the open end of the fascia as shown. 2.2 Repeat on the other end. 3.1 Facing the window, tilt the top of the shade assembly C away from you and insert its top rear edge into the channel in the shade rail A. 3.2 Push the bottom of the shade toward the window and lock it into the shade rail with a “click.” 1.1 Hold the shade rail A up to the mounting surface. Approximate its final position and use a pencil to mark mounting screw locations on the shade rail.* 1.2 Pre-drill the shade rail A at the pencil marks. 1.3 Fasten the shade rail A, to the mounting surface using the mounting screws provided B or other appropriate fasteners.NOTE: The shade rail features grooves to help stabilize the point of your drill bit.**NOTE: Depending on the size of your shade and the depth of your trim, or the roll direction of your shade, you may be able to mount the shade directly to the wall above the trim without additional spacing.In this arrangement, the top of the shade rail must be a minimum of 4 1/2 in (114 mm) above the top of the trim.Optional fascia/end caps not shownNOTE: If your shade was ordered with optional fascia, the fascia will be factory-attached and wrapped with the shade. Leave the wrapping in place during installation for added stability, then remove the wrap before installing batteries.*To ensure the shade rail is properly mounted, we rcommend:a. Install mounting screws 6-12 in (152-305 mm) from each end of the shade rail.b. Locate the mounting screws so that they drive into studs or solid trim. For other surfaces, use appropriate expansion anchors, toggle bolts, or other fasteners, (not included).c. Verify that the mounted shade rail is level and parallel to the window opening.#2 Phillips Driver Bit1/8 in (3.2 mm) Drill BitPencilLevelD-Cell Alkaline Batteries(6 or 8 depending on shade size)Power DrillOPTIONAL(1) Shade RailAMounting ScrewsBSerena® Roller Shade AssemblyC(1) Fascia with end capsDCLICK!CLICK!ABACAOutside Mount on TrimOutside Mount above TrimASpacer blocks or board (not included)securely mounted to wall above trim**GROOVESWorldwide Headquarters | USALutron Electronics Co., Inc. 7200 Suter Road, Coopersburg, PA 18036-1299 USATEL: 1.610.282.3800 • FAX: 1.610.282.3090Technical Support: 1.800.523.9466 • Toll Free: 1.888.LUTRON1Email: shadinginfo@lutron.com • Online: www.lutron.com/shadingsolutionsEurope Headquarters | United KingdomLutron EA Ltd. 6 Sovereign Close, London, E1W3JF, UKTEL: +44.(0)20.7702.0657 • FAX: +44.(0)20.7480.6899Technical Support: +44.(0)20.7680.4481FREEPHONE: 0800.282.107Inside MountBBIncluded in the box:Other items you’ll need:End CapsLeft end cap shownLeft end cap installedFasciaLeft RightNOTE: If your shade will be inside-mounted, both end caps must be installed and fully seated before proceeding to the next step.4.5 in(114 m m)min.Wall RegularrollReverserollTrim
Lutron Electronics Co., Inc.7200 Suter RoadCoopersburg, PA 18036-1299, U.S.A.09/2013P/N 045404 Rev. ALutron, O, Serena and Pico are registered trademarks of Lutron Electronics Co., Inc.Serena® Roller Shade Installation and Setup Guide Page 2 6 Adjusting shade limits and presets (OPTIONAL): 6.1 Adjust Upper or Lower Limit (OPTIONAL)The shade’s upper and lower limits are pre-programmed based on the window dimensions and mounting option. If adjustment is needed, follow these steps:Serena® 4-Group RF remote controlShade Button with LEDOpenCloseShade All1 23 4OpenCloseShade All1 23 4 5 Assigning a remote control:Pico® wireless controlExposed headrail: rotate the top section forward. Exposed headrail: rotate the top section back to the closed positionOpenOpenPresetPresetCloseCloseShade GroupsLowerLowerAll Shade GroupsRaiseRaise 5.1 Assign a Pico® Wireless ControlPress and hold the Close button.Tap the Shade Button.Tap the Shade Button.The Shade Button lights.The Shade Button lights.The Shade Button flashes. Assignment is complete.The Shade Button flashes. Assignment is complete.Repeat for additional shade/control assignments.Repeat for additional shade/control assignments. 5.2 Assign a Serena® 4-Group RF Remote ControlChoose a Shade Group button. Press and hold.The Shade Button flashes, then stays on.Compatible Remote Controls (sold separately)Press and hold the Open and Raise Buttons.Press and hold the Preset Button.Use the Raise and Lower Buttons to position the shade at the preferred upper or lower limit. 6.2 Set Preset Level (OPTIONAL)The preset level is factory programmed to 50% open/closed.Tap the Shade Button.The Shade Button lights.The Shade Button flashes. Limit set is complete.The Shade Button flashes. Preset level is set.SET UPPER LIMITWith the shade at the preferred upper limit, press and hold the Open Button.OR SET LOWER LIMITWith the shade at the preferred lower limit, press and hold the Close Button.Use the Raise and Lower Buttons to position the shade at the desired preset level. 4 Installing the batteries: 4.1 Open the battery holder at the top of the shade. 4.2 Insert new D-cell alkaline batteries. 4.3 Return the battery holder to the closed position. With optional fascia: pull straight down on the fascia. With optional fascia: gently push straight up on the fascia.A label on the battery holder shows quanity and orientation.FCC InformationModels: SYC-J-EDU-R2, QSFC-J-EDU-R2This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Worldwide Headquarters | USALutron Electronics Co., Inc. 7200 Suter Road, Coopersburg, PA 18036-1299 USATEL: 1.610.282.3800 • FAX: 1.610.282.3090Technical Support: 1.800.523.9466 • Toll Free: 1.888.LUTRON1Email: shadinginfo@lutron.com • Online: www.lutron.com/shadingsolutionsEurope Headquarters | United KingdomLutron EA Ltd. 6 Sovereign Close, London, E1W3JF, UKTEL: +44.(0)20.7702.0657 • FAX: +44.(0)20.7480.6899Technical Support: +44.(0)20.7680.4481FREEPHONE: 0800.282.107Caution: Changes or modifications not expressly approved by Lutron Electronics Co. could void the user’s authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003.IC InformationThis device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject tot he following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired operation of the device.For complete warranty information, please see: www.serenashades.com/warranty

Navigation menu