Lutron Electronics 0039 Wireless Roller 64 for HomeWorks User Manual master

Lutron Electronics Company Inc Wireless Roller 64 for HomeWorks master

Users Manual

Sivoia QED™Wireless Roller 64™for HomeWorks®InstallationInstructions
Sivoia QEDTM |Wireless Roller 64 for HomeWorksInstallation InstructionsSIVOIA QEDTM Wireless Roller 64 Installation Instructions 1Tools Required:Tape Measure 1/4” Hex-Head DriverWire Cutter/Stripper LevelPliers Power Drill#2 Phillips ScrewdriverSivoia QED™Wireless Roller 64Standard Mounting Brackets with Retaining Screws(5) Mounting Screws (#8x1-3/4" (#8x44mm) Hex Head Screws)(1) 3 Pin Terminal Block(Actual Size)(1) Programming Stylus (1) Screwdriver(2) 4” (102mm) Cable TiesNotes:1) For Wireless Roller 64 programming refer to the HomeWorks®Illumination Online Help.2) The Electronic Drive Unit (EDU) will need to be powered to complete installation. Wireless Shades will not function until they are addressed and programmed using the HomeWorks®Illumination Software.Box Contents:(2) Bracket Leveling Spacer (2) Cable Tie Anchor(2) AntennaMounting Clips
SIVOIA QEDTM Wireless Roller 64 Installation Instructions 2Warning: Incorrect installation can lead to severe injury, follow all installation instructions.Notes:• The Sivoia QED Wireless Roller 64 must be used only with window treatments approved by Lutron.• There must be a clearance of at least 1.3 feet (0.4 meters) between the fully lowered system and any permanent object.• Installation shall be executed by a qualified electrician according to national wiring rules.• Before shade installation, remove any unnecessary cords and disable any equipment not needed for powered operation. The Sivoia QED Wireless Roller 64 has a maximum rated operating time of 8 min. out of 20.• Codes: Install in accordance with all local and national electrical codes. • Environment: Ambient operating temperature: 0-40°C, 32-104°F, 0-90% humidity, non-condensing.Indoor use only.Sivoia QEDTM |Wireless Roller 64 for HomeWorksInstallation Instructions (continued)
SIVOIA QEDTM Wireless Roller 64 Installation Instructions 3Sivoia QEDTM |Wireless Roller 64 for HomeWorksInstallation Instructions (continued)• RF Device Placement: Wireless shades must be located within 30 feet (9m) of an RF Signal Repeater or an RF Processor. The distance between repeater and processor must be less than 60 feet (18m).Wireless shades will not function until they are addressed and programmed. See the HomeWorks Illumination Software Online Help.Wireless shades are programmed with a personal computer using the HomeWorks Illumination Software.30 feet (9m)30 feet (9m)
SIVOIA QEDTM Wireless Roller 64 Installation Instructions 41Confirm System Dimensions 1.11System Width(Bracket to Bracket Width)System HeightSystem Width System HeightCompare system dimensions onthe package label with the windowdimensions to verify appropriatewindow/shade combination. 1.1Package Label
SIVOIA QEDTM Wireless Roller 64 Installation Instructions 52Position the Mounting BracketsMark the location of the mounting brackets so that they are centered over the window.Note: Bracket to Bracket distance = Fabric Width + 1.5” (38 mm) = System Width.Note: For ceiling and jamb mount, allow clearance to prevent fabric from rubbing against trim, window, top treatment, etc.Note: Wall mount may require blocks (not provided) to clear trim.2.1AAA(System Width)
SIVOIA QEDTM Wireless Roller 64 Installation Instructions 63Install the Mounting BracketsInstall the first mounting bracket.3.1Install the second mounting bracket.Note: Put a screw in the center of each slot. Use slots as needed to ensure brackets are level and plumb as positioned.3.2
4Pre-drill for Cable RunWall MountWall MountSIVOIA QEDTM Wireless Roller 64 Installation Instructions 7DANGER - Locate and lock breaker to the shade power supply in the OFF position or unplug the power plug-in transformer before doing any wiring.Choose one of the options below to drill for cable access.Note: Cable should exit from wall, ceiling, or jamb on EDU side of system.Note: Leave 12-18” (30-45 cm) of cable exposed.Wall Mount with wires through:A) Wall: 1” in from end of system and .5” from top of bracketB) Ceiling: .5” in from end of system and .5” from mounting wallC) Jamb: 1” from top of bracket and .5” from mounting wall4.1ABC
SIVOIA QEDTM Wireless Roller 64 Installation Instructions 84Pre-drill for Cable Run: (continued)Ceiling MountCeiling Mount with wires through:A) Wall: 1” in from end of system and .5” from ceilingB) Ceiling: 1” in from end of system and .5” from back of bracketC) Jamb: 1” from back of bracket and .5” from ceiling4.2Ceiling MountABC
SIVOIA QEDTM Wireless Roller 64 Installation Instructions 94Pre-drill for Cable Run: (continued)Jamb MountJamb Mount with wires through:A) Wall: .5” from ceiling and .5” from outside of jambB) Ceiling: .5” from wall and .5” from outside of jambC) Jamb: .5” from ceiling and .5” from wall4.3Jamb MountABC
SIVOIA QEDTM Wireless Roller 64 Installation Instructions 105Wire 3-Pin Terminal BlockStrip 2” of jacket off cable run fromthe wall.5.1Wire 3-Pin terminal block (provided) to cable using the included screwdriver.5.2To EDUConnectorEGND (Pin 3)24 VAC (Pin 2)24 VAC (Pin 1)
SIVOIA QEDTM Wireless Roller 64 Installation Instructions 116Orient the Buttons and WiringFor the following bracket and button orientations, route the wires as shown.6.1Note: The buttons should be accessible when the shade is installedNote: The wires may go in either or both of the indicated slotsButtonsEither DirectionEither DirectionEither DirectionEither Direction
SIVOIA QEDTM Wireless Roller 64 Installation Instructions 127Mount the ShadeInstall the idler side of the shade onto its bracket.7.1Depress the spring loaded idler by pressing the shade towards the idler, and install the EDUside of the shade onto its bracket.7.2
SIVOIA QEDTM Wireless Roller 64 Installation Instructions 138Adjust the ShadeEnsure that the shade is level and centered. 8.1Adjust shade by removing the necessary screws and moving the brackets as needed, or installing bracket leveling spacers.Note: You may have to remove the shade to access the bracket screws.8.2Reinstall and tighten the screws.8.3
149Secure the AntennaSIVOIA QEDTM Wireless Roller 64 Installation InstructionsWARNING: - The antenna is covered with a clean Plastic sleeve to protect it. Do notcut the antenna or remove the plastic sleeve. Do not modify the antenna.For optimal performance secure the antenna in 1 of 3 configurations shown below usingthe antenna clips provided.9.1Antenna mounted parrallel with shadeuse these configurations. When Pocketor Fascia is not used.Antenna mounted straight down.Antenna clipped to bottom of Pocket or Fascia - This configuration provides optimal performance withmetal Fascia.Note: Lutron has tested this product with the antenna mounted in the configurations above and found that these provide optimal performance.
SIVOIA QEDTM Wireless Roller 64 Installation Instructions 1510 Connect Terminal BlocksPlug 7-pin terminal block on cable into EDU terminal block attached to shade bracket (a cable tie can be used to secure the terminal blocks together).10.1Dress wires to ensure fabric does not rub while the shade is moving.WARNING: Do not cut wires coming out of shade. Doing so will damage the antenna.10.2Copy the serial number located on every shade’s harness and shade location on page 21 of thismanual. This will ease addressing and programming later on the installation.10.3
SIVOIA QEDTM Wireless Roller 64 Installation Instructions 1611 Secure and Check the ShadeTighten retaining screws in each bracket to secure the shade.11.1
SIVOIA QEDTM Wireless Roller 64 Installation Instructions 17Reconnect power to the shade power supply.Use the programming stylus to run the shade up and down using the adjustment buttons ( ), re-level if needed.Observe: Pay careful attention to the shade roll up to ensure that it does not telescopeextremely to one side or the other.Tip: Slight telescoping is normal. However, if the shade is telescoping severely to oneside and it is level, press the “Close Limit Button” ( ), and lower the shade all the waydown using the adjustment buttons ( ). Place a piece of tape on the side of the tubethat the fabric is telescoping away from when finished press the “Close Limit Button” ( )once. This technique is referred to as “SHIMMING”. The shade will always track towardsthe side that the tape (shim) is placed on. 11.2 Secure and Check the Shade (continued)
Press and hold the “OpenLimit Button” ( ) for 5 seconds. The green LED onthe roller shade EDU willflash for 2 seconds, then godark, indicating that thecurrent position has beenstored as the Open Limit.Adjust the position of theEDU to the desired OpenLimit using the adjustmentbuttons ( ). Note: Setting the Open Limit lower than the Close Limit will cause the shade to move down when raise is pressed and up when lower is pressed. Setting the Open Limit from the EDU12 Setting Limits from the EDUTap the “Open Limit Button”( ), the green LED on theroller shade EDU will turn onsteady, indicating that the EDUis in “Set Open Limit Mode.”12.112.212.3SIVOIA QEDTM Wireless Roller 64 Installation Instructions 18
SIVOIA QEDTM Wireless Roller 64 Installation Instructions 1912.512.612.412 Setting Limits from the EDU (continued)Setting the Close Limit from the EDUPress and hold the “CloseLimit Button” ( ) for 5 seconds. The green LED onthe roller shade EDU willflash for 2 seconds, then godark, indicating that thecurrent position has beenstored as the Close Limit.Tap the “Close LimitButton” ( ). The greenLED on the roller ShadeEDU will turn on steady, indicating that the EDU is in “Set Close Limit Mode”.Adjust the position of theEDU to the desired CloseLimit using the adjustmentbuttons ( ).
SIVOIA QEDTM Wireless Roller 64 Installation Instructions 2013 Finish System ProgrammingThe Sivoia QED shade is now installed, wired, and the OPEN/CLOSE limits for each shade havebeen set.The next step is to finish programming the system, using the HomeWorks Illumination Software.
SymptomShade will not move usingadjustment buttons on EDU...Solution...EDU is not powered - check EDU Power.By unplugging and re-plugging in EDU.LED should light for 5 seconds....Shade is caught on something - free shade....Shade is not programmed to keypad or event.Shade does not fully open or fully close... ...Limits have been set incorrectly - refer to “setopen limit” and “set close limit” sections on re-setlimits using HW1 Software....Shade fabric is caught on something - free shade.Fabric not level... ...Check that brackets are mounted level....Check that fabric is tracking correctly on the shade tube.Fabric not centered over window... ...Check that brackets are centered.Shade does not move smoothly... ...Check for binding of shade fabric on side channels....Check fabric tracking.Wireless Shade can not be addressed.... ...Shade is out of RF communications range.Move RF signal repeater or RF processor to within 30 feet (9m) of shade.2114 TroubleshootingSIVOIA QEDTM Wireless Roller 64 Installation Instructions
SIVOIA QEDTM Wireless Roller 64 Installation Instructions 22Shade Location SerialNumber1234567891011121314151617181920212223242526272829303132Shade Location SerialNumber3334353637383940414243444546474849505152535455565758596061626364
FCC InformationNOTE: This equipment has been tested andfound to comply with the limits for a Class Bdigital device, pursuant to part 15 of the FCCrules. These limits are designed to providereasonable protection against harmfulinterference in a residential installation. Thisequipment generates, uses and can radiateradio frequency energy and, if not installed andused in accordance with the instructions, maycause harmful interference to radio or televisionreception, which can be determined by turningthe equipment off and on, the user isencouraged to try to correct the interferenceby one or more of the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between theequipment and receiver.•Connect the equipment into an outlet on acircuit different from that to which thereceiver is connected.•Consult the dealer or an experiencedradio/TV technician for help.Caution: Changes or modifications notexpressly approved by Lutron Electronics Co.could void the user's authority to operate this equipment.Industry CanadaInformationThe term “IC” before the radiocertification number only signifies thatIndustry Canada technical specificationswere met.Limited WarrantyLutron offers an 8-year limited warranty for ourshading systems. Please contact customerservice or visit our website for a complete warranty statement.Lutron reserves the right to make improve-ments or changes to these products withoutprior notice. Although every attempt is made toensure that this information is accurate and upto date, please check with Lutron to confirmproduct availability, the latest specifications,and suitability for your application.These products may be covered by one ormore of the following US patents: 5,983,783and corresponding foreign patents.US and foreign patents pending.Lutron, the Sunburst logo, and Sivoia are registered trademarks, and Sivoia QED is atrademark of Lutron Electronics Co., Inc.Technical AssistanceWORLD HEADQUARTERSLutron Electronics Co., Inc.7200 Suter RoadCoopersburg, PA 18036United StatesTel: +1-610-282-3800Fax:+1-610-282-1243CUSTOMERSERVICE/ORDERINGUSA +1-888-LUTRON108.00 - 20.00 ESTCUSTOMER SERVICE/E-MAILshadinginfo@lutron.comTECHNICAL SUPPORT & SERVICESUSA +1-800-523-9466 – 24 hours/7 daysINTERNET:www.lutron.com©2006 LUTRON Electronics Co., Inc.Printed in the U.S.A.P/N 045-119 REV. A

Navigation menu