Lutron Electronics 0030 Control Unit User Manual 031 xxxa RadioTouch addendum

Lutron Electronics Company Inc Control Unit 031 xxxa RadioTouch addendum

Users Manual

Attention Contractors...Installer’s Guide Addendum forTabletop TransmittersA Step-by-Step Guide for Installing, and Operating Tabletop Transmitters for use with a Lutron RadioTouchTMVisual Environment Control System1234 5678 9101112 13141516CLASS 2 LOW VOLTAGE WIRING12345 Power Status Program Burn-In123Sivoia Cntrl 1Sivoia Cntrl 2RTA-RX-F-SCRadio Frequency Controller LISTED 243CInd. Cont. Eq.Coopersburg, PA 18036STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF DataRadioTouch1234567891011 12 13 14 15 16Occ. ComSignal15V24VCircuit ComSw Closure 1Sw Closure 2Sw Closure 3Sw Closure 4Sw Closure 5Closure Com0-10 Purple0-10 GrayReceiverSettingsTerminal connectionsare Class 2.TMOcc. Sensor 0-10 V Shade Swit c h C losures12345PoweredWhen LitStatusIndicatorProgramButtonBurn-inButtonRECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-FDB Mode DN.-ECO Mode4. UP-OFF DN.-Min. Light5. UP-Auto ON DN.-Manual ONSee Installers Guide for SystemAddressing and Programming Instructions®123ShadeSettingsSHADE SWITCH SETTINGS1. UP-A/C Shades DN.-Normal Oper.PS Signal© 2000-2002 Lutron Electronics Co., Inc.
2RadioTouch Tabletop Transmitter AddendumHardware InstallationRadioTouch1234 5678 9101112 13141516CLASS 2 LOW VOLTAGE WIRING12345 Power Status Program Burn-In123Sivoia Cntrl 1Sivoia Cntrl 2RTA-RX-F-SCRadio Frequency Controller LISTED 243CInd. Cont. Eq.Coopersburg, PA 18036STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF DataRadioTouch1234567891011 12 13 14 15 16Occ. ComSignal15V24VCircuit ComSw Closure 1Sw Closure 2Sw Closure 3Sw Closure 4Sw Closure 5Closure Com0-10 Purple0-10 GrayReceiverSettingsTerminal connectionsare Class 2.TMOcc. Sensor 0-10 V Shade Switch Closures12345PoweredWhen LitStatusIndicatorProgramButtonBurn-inButtonRECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-FDB Mode DN.-ECO Mode4. UP-OFF DN.-Min. Light5. UP-Auto ON DN.-Manual ONSee Installers Guide for SystemAddressing and Programming Instructions®123ShadeSettingsSHADE SWITCH SETTINGS1. UP-A/C Shades DN.-Normal Oper.PS Signal© 2000-2002 Lutron Electronics Co., Inc.Addressing a Tabletop TransmitterEach column of buttons on the tabletop transmittermust be addressed to the Controller that you wish tocontrol with that column.Addressing Columns of ButtonsStep A - Press and release the programming button onthe Controller. After the button is pressed the lights willcycle up and down for 3 seconds to notify you that youare in programming mode, and settle at 50% lightoutput. If you are using an RTA-RX-SW the lights willcycle OFF and ON. The Status LED will be in fast blinkmode.Press and holdthis buttonStep B - While in programming mode press thecorresponding button in the column that you want tocontrol the receiver and hold for 5 seconds (seeTransmitter diagrams below). The Controller will flashor cycle the lights OFF and ON when the transmitter isadded. If no lights are being controlled by the receiver,you will not get visual feedback.Step C - Press the programming button again to exitfrom programming mode. The lights will go to high endand the Status LED will return to slow blink mode. Ifyou are using an RTA-RX-SW the lights will cycle OFFand ON. To test the tabletop transmitter for lights, pressany button in the column added on the tabletoptransmitter and verify that the lights respond. ForSivoia®shades, press any button and see that theshades move. If no response return to step A and besure to hold the buttons for 5 seconds while in step B. Step D - Repeat steps A through C for each columnyou need to address to a Controller.Programming buttonStatus LEDStep A & CPress and holdthis buttonPress and holdthis buttonStep B - Columns of buttonsTwo button Switch Closure Three button Switch ClosureDimmable Lights Non-dim LightsFour button Switch Closure Five button Switch Closure
3RadioTouch Tabletop Transmitter AddendumHardware InstallationRadioTouchDeleting a Tabletop TransmitterEach column of buttons on the tabletop transmittermust be deleted separately from the Controller that youno longer wish to control.Deleting Columns of LightsStep A - Press and release the programming button onthe Controller. After the button is pressed the lights willcycle up and down for 3 seconds to notify you that youare in programming mode, and settle at 50% lightoutput. If you are using an RTA-RX-SW the lights willcycle OFF and ON. The Status LED will be in fast blinkmode.Step B - While in programming mode press thecorresponding buttons in the column that you want todelete from the Controller and hold for 5 seconds (seeTransmitter diagrams below). The Controller will flashthe lights when the transmitter is deleted. If no lightsare being controlled by the Controller, you will not getvisual feedback.Step C - Press the programming button again to exitfrom programming mode. The lights will go to high endor turn ON, and the Status LED will return to slow blinkmode. To test the Tabletop Transmitter press any buttonon the transmitter in the column that has been deletedand verify that the lights or shades do not respond.Step D - Repeat for each row you need to delete froma Controller.1234 5678 9101112 13141516CLASS 2 LOW VOLTAGE WIRING12345 Power Status Program Burn-In123Sivoia Cntrl 1Sivoia Cntrl 2RTA-RX-F-SCRadio Frequency Controller LISTED 243CInd. Cont. Eq.Coopersburg, PA 18036STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF DataRadioTouch1234567891011 12 13 14 15 16Occ. ComSignal15V24VCircuit ComSw Closure 1Sw Closure 2Sw Closure 3Sw Closure 4Sw Closure 5Closure Com0-10 Purple0-10 GrayReceiverSettingsTerminal connectionsare Class 2.TMOcc. Sensor 0-10 V Shade Switch Closures12345PoweredWhen LitStatusIndicatorProgramButtonBurn-inButtonRECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-FDB Mode DN.-ECO Mode4. UP-OFF DN.-Min. Light5. UP-Auto ON DN.-Manual ONSee Installers Guide for SystemAddressing and Programming Instructions®123ShadeSettingsSHADE SWITCH SETTINGS1. UP-A/C Shades DN.-Normal Oper.PS Signal© 2000-2002 Lutron Electronics Co., Inc.Press and holdthis buttonProgramming buttonStatus LEDStep A & CPress and holdthese buttonsPress and holdthese buttonsStep B - Columns of buttonsTwo button Switch Closure Three button Switch ClosureDimmable Lights Non-dim LightsFour button Switch Closure Five button Switch Closure
4RadioTouch Tabletop Transmitter AddendumHardware InstallationRadioTouchSetting the ON light level of a twobutton, dimmable lighting column -Remote MethodNote: No DIP switches need to be switched to performthis operation.Step A - Press and hold the ON and the lower buttonsfor 5 seconds. The lights will flash to notify you that youare in Preset Adjust Mode, and settle at 100% lightlevel.Step B - Using the raise/lower buttons in that columnon the transmitter controlling the Controller that you areadjusting, set the lights at the new ON level.Step C - Press and hold the ON and raise buttons for 5seconds. The lights will flash to notify you that the ONlevel has changed. Step D - Press and hold the ON and the lower buttonsfor 5 seconds to exit Preset Adjust Mode. The lights willflash and return to their maximum light level. Test theON button to make sure the light level is correct. If not,repeat steps A through D.Notes:•The Controller will not react to preset button pressesfrom any transmitter while the Controller is in PresetAdjust Mode.•Preset light levels may be affected by a photosensorinput. As ambient light increases / decreases thepreset light levels will scale accordingly.Press and holdthese two buttonsfor 5 secondsStep A & D Step CPress and holdthese two buttonsfor 5 secondsPress and holdthese two buttonsfor 5 secondsSetting the ON light level of a twobutton, dimmable lighting column -DIP Switch MethodStep A - Flip DIP switch #1 down on the Controller.After the switch is flipped the Controller will be in PresetAdjust Mode. (If a photosensor is connected to thisController your lights may change level when DIPswitch #1 is flipped.) Step B - Using the raise/lower buttons on thetransmitter controlling the Controller that you are adjust-ing, set the lights at the new ON level.Step C - Press and hold the ON and raise buttons for 5seconds. The lights will flash to notify you that the ONlevel has changed. Step D - Flip DIP switch #1 back up to exit PresetAdjust Mode.Notes:•The Controller will not react to preset button pressesfrom the transmitter while the Controller DIP switch#1 is flipped to the down position.•Preset light levels may be affected by a photosensorinput. As ambient light increases / decreases thepreset light levels will scale accordingly.Step A & D Step C1234 5678 9101112 13141516CLASS 2 LOW VOLTAGE WIRING12345 Power Status Program Burn-In123Sivoia Cntrl 1Sivoia Cntrl 2RTA-RX-F-SCRadio Frequency Controller LISTED 243CInd. Cont. Eq.Coopersburg, PA 18036STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF DataRadioTouch1234567891011 12 13 14 15 16Occ. ComSignal15V24VCircuit ComSw Closure 1Sw Closure 2Sw Closure 3Sw Closure 4Sw Closure 5Closure Com0-10 Purple0-10 GrayReceiverSettingsTerminal connectionsare Class 2.TMOcc. Sensor 0-10 V Shade Sw itc h Closures12345PoweredWhen LitStatusIndicatorProgramButtonBurn-inButtonRECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-FDB Mode DN.-ECO Mode4. UP-OFF DN.-Min. Light5. UP-Auto ON DN.-Manual ONSee Installers Guide for SystemAddressing and Programming Instructions®123ShadeSettingsSHADE SWITCH SETTINGS1. UP-A/C Shades DN.-Normal Oper.PS Signal© 2000-2002 Lutron Electronics Co., Inc.Flip DIP switch#1 to the downposition
5RadioTouch Tabletop Transmitter AddendumHardware InstallationRadioTouch1234 5678 9101112 13141516CLASS 2 LOW VOLTAGE WIRING12345 Power Status Program Burn-In123Wiring output switch closures toother equipment (RTA-RX-F-SC only)The RadioTouch controller has the ability to provide 5momentary dry output switch closures. These closurescan be used to operate AC shades, MotorizedProjection Screens, or other equipment designed toaccept momentary dry switch closures. A column of 5 buttons on a Tabletop Transmittercorrespond to Switch Closures 1 through 5 on theController. A two button column on a Tabletop Transmitter willactivate Switch Closures 2 and 4.A three button column on a Tabletop Transmitter willactivate Switch Closures 2, 4, and 3, in that order. (Seediagrams below.)The switch closure outputs on the RadioTouchController provide a momentary dry closure for 0.250seconds to other equipment. The closure terminals areshown below.Switch Closure Outputs – Not toexceed 30VDC and 1/3 Amp.Closure 2Closure 4Closure 2Closure 4Closure 3Sivoia Cntrl 1Sivoia Cntrl 2RTA-RX-F-SCRadio Frequency Controller LISTED 243CInd. Cont. Eq.Coopersburg, PA 18036STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF DataRadioTouch1234567891011 12 13 14 15 16Occ. ComSignal15V24VCircuit ComSw Closure 1Sw Closure 2Sw Closure 3Sw Closure 4Sw Closure 5Closure Com0-10 Purple0-10 GrayReceiverSettingsTerminal connectionsare Class 2.TMOcc. Sensor 0-10 V Shade Switch Closures12345PoweredWhen LitStatusIndicatorProgramButtonBurn-inButtonRECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-FDB Mode DN.-ECO Mode4. UP-OFF DN.-Min. Light5. UP-Auto ON DN.-Manual ONSee Installers Guide for SystemAddressing and Programming Instructions®123ShadeSettingsSHADE SWITCH SETTINGS1. UP-A/C Shades DN.-Normal Oper.PS Signal© 2000-2002 Lutron Electronics Co., Inc.Switch Closure CommonSwitch Closure 5Switch Closure 4Switch Closure 3Switch Closure 2Switch Closure 1Tabletop Button FunctionsTwo and Three button Switch Closures Closure 1Closure 2Closure 3Closure 4Closure 5Five button Switch Closures
6RadioTouch Tabletop Transmitter AddendumHardware InstallationRadioTouchOpenStopCloseTabletop Button FunctionsSetup for AC Motorized WindowTreatments (RTA-RX-F-SC only)Make sure that the RadioTouch Controller is properlywired. Refer to the RadioTouch Installer’s Guide (P/N030-200) for detailed wiring information.Step A - On the RadioTouch Controller, flip SHADESETTINGS DIP SWITCH #1 UP for open, close, andstop functionality.Step B - Make sure appropriate transmitters are addedto the Controller. See page 2 for Addressing TabletopTransmitters to Controllers. Three button Switch ClosureUpDownTabletop Button FunctionsSetup for AC Motorized ProjectionScreens (RTA-RX-F-SC only)Make sure that the RadioTouch Controller is properlywired. Refer to the RadioTouch Installer’s Guide (P/N030-200) for detailed wiring information.Step A - On the RadioTouch Controller, flip SHADESETTINGS DIP SWITCH #1 DOWN for up and downfunctionality.Step B - Make sure appropriate transmitters are addedto the Controller. See page 2 for Addressing TabletopTransmitters to Controllers. Two button Switch Closure
7RadioTouch Tabletop Transmitter AddendumNotes
Lutron Electronics Co., Inc., reserves the right to makeimprovements or changes in its products without priornotice. Although every attempt is made to ensure thatthis information is accurate and up to date, pleasecheck with Lutron to confirm product availability, latestspecifications and suitability for your application.World HeadquartersLutron Electronics Co., Inc.7200 Suter RoadCoopersburg, PA 18036-1299 U.S.A.TOLL FREE: (800) 523-9466 (U.S.A., Canada, andthe Caribbean)Tel: (610) 282-3800; International 1610 282-3800Fax: (610) 282-3090; International 1610 282-3090European HeadquartersLutron EA LTDLutron House6 Sovereign CloseWappingLondon, E1 9HW EnglandFREEPHONE: 0800 282107 (U.K.)Tel: (0171) 702-0657; International 44-171-702-0657Fax: (0171) 480-6899; International 44-171-480-6899Japan Sales OfficeLutron Asuka Co., LtdNo. 16 Kowa Bldg. 4F1-9-20 Akasaka, Minato-ku Tokyo 107-0052 JapanTOLL FREE: (0120) 083417 (Japan)Tel: (03) 5575-8411; International 81-3-5575-8411Fax: (03) 5575-8420; International 81-3-5575-8420 Hong Kong Sales OfficeTel: 2104-7733; International 852-2104-7733Fax: 2104-7633; International 852-2104-7633LIMITED WARRANTYLutron will, at its option, repair or replace any unit thatis defective in materials or manufacture within one yearafter purchase. For warranty service, return unit toplace of purchase or mail to Lutron at 7200 Suter Rd.,Coopersburg, PA 18036-1299, postage pre-paid.THIS WARRANTY IS IN LIEU OF ALL OTHEREXPRESS WARRANTIES, AND THE IMPLIED WAR-RANTY OF MERCHANTABILITY IS LIMITED TO ONEYEAR FROM PURCHASE. THIS WARRANTY DOESNOT COVER THE COST OF INSTALLATION,REMOVAL OR REINSTALLATION, OR DAMAGE RE-SULTING FROM MISUSE, ABUSE, OR DAMAGEFROM IMPROPER WIRING OR INSTALLATION. THISWARRANTY DOES NOT COVER INCIDENTAL ORCONSEQUENTIAL DAMAGES. LUTRON’S LIABILITYON ANY CLAIM FOR DAMAGES ARISING OUT OFOR IN CONNECTION WITH THE MANUFACTURE,SALE, INSTALLATION, DELIVERY, OR USE OF THEUNIT SHALL NEVER EXCEED THE PURCHASEPRICE OF THE UNIT.This warranty gives you specific legal rights, and youmay have other rights which vary from state to state.Some states do not allow the exclusion or limitation ofincidental or consequential damages, or limitation onhow long an implied warranty may last, so the abovelimitations may not apply to you. These products may be covered by one of more of the following U.S. patents: 4,663,570; 4,751,399;4,783,581; 4,835,343; 4,894,587; 5,001,386; 5,041,763;5,055,742; 5,142,199; 5,144,205; 5,173,643; 5,224,029;5,248,919; 5,281,961; 5,293,097; 5,309,068; 5,357,170;5,399,940; 5,555,150; 5,633,540; 5,637,930; 5,736,965;5,798,581; 5,838,226; 5,841,239; 5,848,054; 5,864,212;5,905,442; 5,942,727; 5,962,979; 5,982,103; 6,111,368;6,313,588; 6,346,781; RE37,135; 6,225,760; DES353,798; DES 364,141; DES 378,814; DES 389,461;DES 389,805; DES 395,037; DES 404,013; DES422,969; DES 428,855; DES 436,579; DES 439,220;and corresponding foreign patents. Other U.S. andforeign patents may be pending.Lutron, is a registered trademark and RadioTouch is atrademark of Lutron Electronics Co., Inc. Technical and Sales AssistanceIf you have questions concerning the installation oroperation of this product, call the toll-free LutronTechnical Support Center. Please provide exactmodel number when calling.U.S.A., Canada, and the Caribbean(800) 523-9466 27 hrs/7 days other countries(610) 282-3800 8:00a.m. – 8:00p.m. ETOur address on the web is http://www.lutron.com© 2003 Lutron Electronics Co., Inc.MADE AND PRINTED IN U.S.A.P/N 031-xxx Rev. A 12/03

Navigation menu