Longhorn Technology H-113 PARKING SENSOR User Manual 1

Shenzhen Longhorn Technology Co., Ltd. PARKING SENSOR 1

Users Manual

USER'S MANUALWireless Parking SensorSystem For TruckH-113Printed in China
 GENERAL INSTALLATION DIAGRAM       LED DIGITAL DISPLAYDisplayControl box SensorDisplayControl boxRed wireBlack wireSensorsTop viewSide view Safe area Alarm areaDanger area Safe areaAlarm areaDanger areaConnect the powerof reversing light5.5-2.5ft2.5-0.0ft5.5-8.5ft 5.5-8.5ft5.5-2.5ft2.5-0.0ftDETECTING RANGEftft8.08.01.51.5Connect the ACC power
Safe AreaSafe AreaAlarm AreaDanger AreaDanger AreaFix the position of sensor ,and no obstacle should be found at 90 from side  view ,otherwise the system would mis-alarmAdvised position to install the sensorsBest position for 2 sensors Best position for 4 sensorsSensor Installation Diagram1.5f1.5f1.5-5f5.5-8f> 8.5f8.56.03.51.51.00.0DISPLAY STATUSINSTALLATION TOOLSSENSOR INSTALLATION DISGRAM
Objects maybe cause failure detectionSmooth slope Smooth round object Object absorbingwave, e.g. Cotton4 drilled holes (A,B.C.D) shouldbe under the same line.Measure the distance 0.5-0.65f on itsside for position A&D,between sensorA&D get the result “L”,mark sensorB&C for every 1/3 “L”interval. Installation height for sensor can beadjusted,2.5-4.0ft vertically high tothe groundChoose suitable drilling position,in the corresponding position withdrill for fixed.Use screws to fix the sensors  2.   3M sticker paste to the back of control box. Advised position to install the sensorsChoose suitable control box position,then punching in the corresponding position.2.CONTROL BOX INSTALLATION AND CONNECTION1. ADVISED POSITION TO INSTALL THE SENSORS45
Stick the  control box on the fixed position,then fixed by screw.Connect sensor and control boxSticker the control box on thedashboardLet the power line out ward,acknowledge and transmit signalConnect the power line of control boxand power source of reversing light Switch on the display , after normal test ,thenstick 3M stick on the backside of displayDusolay installation7.8.5.0tf6. SENSOR DETECTING4. CONNECTION5. DISPLAY INSTALLATION
H-113  consists of ultrasonic sensors, display and control box . This system detects the distance between the truck and the back obstruction by the ultrasonic sensors. The display  H-113MAIN FEATURESTECHNICAL SPECIFICATIONSALARM MODEINSTALLATION STEPSNOTE1. The car must be in power-off during the installation.  2.Its performance may be affected in following situation: heavy rain, gravel road, bumpy  road sloping road and bush, very cold, hot or moist weather, or the sensor is covered by  ice, mud, etc...  4.The sensors should be installed appropriately loose or tight. 5.Its performance may be affected if the sensors are fixed on metallic bumper. 6. Avoid installing the digital control box in places of great interference, such as vent-pipe,  wiring nearby. 7.Test the system to make sure it works normally before using.  8.This system is a reversing aid and the manufacturer will take no responsibility for any accident after the kit is installed.3.Other ultrasonic or electric wave, the instance of DC/AC switch or 24/12v switch maybe  affect the performance of the system.Digital LED displayDirection indicate or if left ,middle & right.Simulated bars display direction indicatorRated voltage: DC 24V  Operating range: DC 9~32V Operating current: 12V 20-150mA(Be concerned with alarm status)Detection distance:0.5~8.0fUltrasonic frequency: 40KHzWorking temperature: -30~+70℃Display size: 93.2*49*22.3mm1. Choose right installation position for sensors2. Select drilling position for sensor A .B. C.D3. Select drilling position for sensor  4. Locate the position and drill5. Install the sensors and hide the wires6. Install the display 7. Install the control box1.  After the installation of sensors, adjust the axis and direction to the correct range, then arrange the wire in good order;2. Connect the power wire of the control box with the reversing light correctly;4.Put the shift lever to reverse gear, radix point in the display should be lighted, it indicates the system is under detecting status. If not, please check it as following steps. a .If there is not a buzz at the time of power on, please check whether the power wire is connected correctly, whether the voltage is 12V or higher than 9V, whether the display is well connected; b. If the display makes sound like “bi…” continuously, please switch the power off then put the shift lever to reverse gear again, if the problems could not be removed yet, the control unit could be judged to be failed. The whole system should be replaced.5.Connect one sensor with corresponding plug in control box , it can operate normally if person stands in 2.0f. Check other sensors according to this way.  After check, all of sensors would be connected with corresponding plugs.Test: a. When testing some sensor, if the buzzer gives “Bi…” sound , please check whether some parts of the car or some unwanted objects fall into the detecting range, whether the hole is too small to let the sensor too tight in it, whether the sensors is near to some strong interference sources (such as exhaust pipe, other wires);b. If the alarm sound is hint sound in field (eg. “Bi…Bi”) and display shows distance but there are nothing in front of the sensor, maybe the sensor is detecting the ground, please check the position and direction of the sensor; or the sensor maybe detect some parts of the car; c. If above problem still could not be removed, the whole system should be replaced.BiBi alarm soundWire emitting receive system Stage Distance Area Alarm sound Digital Display Alarm Color1 0.0 ~ 0.5fDanger area Bi……... 0.0 ~ 0.521.0f1.03 1.5 ~ 2.0fDanger area Bi…Bi… 1.5 ~ 2.0 3 Green+2 Yellow4 2.5 ~ 3.0f Alarm area Bi.…Bi….2.5 ~ 3.03 Green+1 Yellow5 3.5 ~ 4.0f Alarm area Bi……Bi…… 3.5 ~ 4.0 3 Green64.5 ~ 5.0f Bi……Bi…… 4.5 ~ 5.0 3 Green75.5 ~ 8.0fno voice 5.5 ~ 8.0 2 Green88.5 ~ ∞no voice no displaySafety areaDanger areaAlarm areaSafety areaBi……... 3 Green+2 Yellow+ 1 Redno display3. Connect the control box and display with power, the display has the functionof learning ID, in order that the users could place the display or control box if necessary. will be shown by the digital display, and the driver could judge the distance and avoid the accidentAll LED light upINSTALLATION AND TESTTemperature DisplayThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC NOTE:THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE  CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. FCC Note

Navigation menu