LifeShield SNC1010 Wireless Security Sensor User Manual New Sensor Device Guide indd

LifeShield, Inc. Wireless Security Sensor New Sensor Device Guide indd

User manual

Sensor Installation InstructionsModel SNC1010Test SensorsSensors should be tested to make sure they are installed and working properly. To test the Sensor installation:• With the system disarmed, open the door or window. This separates the Sensor and Magnet and noties the system.You will also hear a chime each time you open and close your door or window.NOTE: MOVING THE GRID EXTENDER OR CONSOLE COULD DISRUPT THE INSTALLATION OF PREVIOUSLY INSTALLED SENSORS. THE SYSTEM WILL BEGIN TO BEEP IF A SENSOR IS NO LONGER WITHIN RANGE OF A GRID CONTROLLER AND THE DISPLAY WILL INDICATE THE NAME OF THE SENSOR THAT IS OUT OF RANGE.NOTE: Add a Grid Controller: If a beep results indicating a Sensor is out of range, you may need to add a Grid Extender or Console for additional range.If these retry solutions do not work, call LifeShield Customer Support for assistance at 1-888-392-2044FCC InformationFCC Part 15This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.CAUTION:Changes and modifications to this product not expressly approved by LifeShield, Inc. could void not only the user’s authority to operate this device, but also the limited warranty.LIFESHIELD LIMITED WARRANTY FOR PRODUCTS AND ACCESSORIES PURCHASED IN THE UNITED STATES OR CANADAWHAT IS COVERED UNDER THIS WARRANTYSubject to the limitations and exclusions contained below, LifeShield, Inc. (“LifeShield”) warrants the LifeShield-branded (including all embedded software) sold by LifeShield for use with the LifeShield Home Security System (the “Products”) to be free from defects in materials and workmanship under normal consumer usage and in accordance with the accompanying instructions and documentation, for the period(s) set forth below. This warranty extends only to the rst consumer purchaser, and is not transferable. LifeShield, at its option, will at no charge repair, replace or refund the purchase price of any Products that do not conform to this limited warranty. We may use functionally equivalent reconditioned/refurbished/pre-owned or new Products or parts and we may retain all replaced Products or parts. No data added to your Products, including but not limited to component names and system preferences, will be reinstalled. This limited warranty is the consumer’s exclusive remedy, and applies to new Products purchased by consumers in the United States or Canada, which are accompanied by this written warranty.PRODUCTS COVERED/LENGTH OF COVERAGE (the “Warranty Period”)New Products: One (1) year from the date of purchase by the rst consumer purchaser of the Product.Products That Are Repaired or Replaced.The balance of the original warranty or for ninety (90) days from the date returned to the consumer, whichever expires later.Batteries. Only batteries whose fully charged capacity falls below 80% of their rated capacity and batteries that leak are covered by this limited warranty.HOW TO OBTAIN WARRANTY SERVICE OR OTHER INFORMATIONTo obtain service or information, please call:LifeShield Customer Service at: 1-888-392-2044Or email us at: support@LifeShield.comYou will receive instructions on how to ship the Products, at your expense, to aLifeShield Authorized Repair Center. To obtain service, you must include:a) a copy of your receipt, bill of sale or other comparable proof of purchaseb) a written description of the problemc) the complete physical address of the location where the system was installed and most importantlyd) your address and telephone number and,e) the “Return Merchandise Authorization” or “RMA” number that LifeShield provides to youWHAT IS NOT COVERED (EXCLUSIONS)Normal Wear and Tear. Periodic repair and replacement of parts due to normal wear and tear are excluded from coverage.Ornamental Decorations. Ornamental decorations, such as emblems and graphics and other decorative elements, are excluded from coverage.Abuse & Misuse. Defects or damage that result from the following are excludedfrom coverage:a) improper operation, storage, misuse or abuse, accident or neglect, such as physical damage (cracks, scratches, etc.) to the surface of the Product;b) contact with moisture, liquids, water, rain, extreme humidity, heavy perspiration or makeup, sand, dirt or the like, food, or proximity to or exposure to heat or cold, re, ood, or lightning;c) other acts which are inconsistent with the instructions and documentation that accompany the Products; andd) use of the Products with any system other than the LifeShield Home Security System.Use of Non-LifeShield Products and Accessories. Defects or damage that result from the use of Non-LifeShield branded or certied products, accessories, software or other peripheral equipment are excluded from coverage, including without limitation defects or damage to Products that result from such use are excluded from coverage.Unauthorized Service or Modification. Defects or damages resulting from service, testing, adjustment, installation, maintenance, alteration, including without limitation, software changes, or modication in any way by someone other than LifeShield, or its authorized agents, are excluded from coverage.Altered Products. Products with the following characteristics are excluded from coverage:a) serial numbers or date tags that have been removed, altered or obliterated;b) broken seals or Products that show evidence of tampering;c) mismatched board serial numbers; ord) nonconforming or non-LifeShield housings, antennas, or parts.Communication Services. Defects, damages, or the failure of Products due to any communication service or signal not provided directly by LifeShield is excluded from coverage.Out of Warranty Products. Defects or damages reported to LifeShield after the Warranty Period are excluded from coverage.Other Exclusions and LimitationsANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY LIMITED IN DURATION TO THE TERM OF THIS EXPRESSED WARRANTY. THE REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE SOLE AND EXCLUSIVE REMEDY OF THE CONSUMER, AND LIFESHIELD’S SOLE AND EXCLUSIVE LIABILITY HEREUNDER, AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. IN NO EVENT SHALL LIFESHIELD BE LIABLE, WHETHER IN CONTRACT, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT GIVING RISE TO THE DAMAGES, OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL, PUNITIVE, EXEMPLARY OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATA, SOFTWARE OR APPLICATIONS OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE USE OF OR THE ABILITY OR INABILITY TO USE THE PRODUCTS OR SOFTWARE TO THE FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW.SOME STATES AND JURISDICTIONS DO NOT ALLOW THE LIMITATION OR EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR A LIMITATION ON THE DURATION OF IMPLIED WARRANTIES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE OR FROM ONE JURISDICTION TO ANOTHER.This warranty gives you specic legal rights, and you may also have other rights that vary from state to state or from one jurisdiction to another.© LifeShield, Inc., 2011. Rev 1/2011.Protected by US patents and patents pending.7 629 880, 7 532 114 7,511,614, 7,495,544, 7,283,048, 7,202,789, 7,119,658, 7,091,827, 7,084,756, 7,079,034, 7,079,020, 7,057,512, 7,053,764, 7,042,353, 7,023,341, 7,019,639, 6,888,459, D538,797, D534,519, D534,146LifeShield Home Security© 2011 LifeShield, Inc. All rights reserved. LifeShield is a registered trademark and LifeShield Home Security is a trademark of LifeShield, Inc.Contact InformationWebsite: www.LifeShield.comMail: LifeShield, Inc. Customer Support 770 Township Line Road, Suite 350 Yardley, PA 19067Phone: 1-888-392-2044E-mail: support@LifeShield.comLi-ionBracket And Magnet InstallationFor WindowsThe process for mounting a Bracket and Magnet to a window is very similar to installing on a door. See the previously shown door installation instructions.Various mounting positions that work for attaching Sensors to windows:
Sensor Kit ContentsSensorMagnetMagnet TapeMagnet SpacerBracketBracket TapeBracket SpacerBracket And Magnet Installation For DoorsDetermine Bracket and Magnet LocationThe Bracket and Magnet should be positioned on interior side of door within 3/4” of each other.NOTE: INSTALL SENSORS ONE AT A TIME FOLLOWING THE STEPS IN THE EXACT ORDER.Various mounting positions that will work for attaching Sensors to doors:Door frame is higher than door. To bring Bracket in alignment, slide spacer onto the Magnet.Bracket on angled door frame and Magnet on door.Place Bracket at 90º angle to Magnet on door. Add Spacers (If Needed)If Bracket and Magnet do not align within 3/4”, add Spacers to either the Bracket or Magnet to make them level.Example: Spacer added to Magnet to close the gap between the Bracket and Magnet to within 3/4”.Spacers slide on Brackets and Magnets.NOTE: THE MAXIMUM DISTANCE BETWEEN THE BRACKET AND MAGNET SHOULD BE NO MORE THAN 3/4”.1. Attach double-sided tape to the bottom of the Magnet.2. Attach Magnet to the door.3. Attach double-sided tape to the bottom of the Bracket.4. Attach the Bracket to the door frame.NOTE: THE MAXIMUM DISTANCE BETWEEN THE BRACKET AND MAGNET SHOULD BE NO MORE THAN 3/4”.Install The SensorOnce the Bracket and Magnet are attached to the door or window, Sensors may be installed. You will need to have the Handset with you to install the Sensor.Remove the battery tab from the SensorEnter the Security MenuBefore clipping the Sensor into the Bracket; Press MENU on your Handset or Console.1. Scroll to the Security Setup and press SELECT.2. Enter Code and press SELECT (for an initial installation the default code is 1234).3. Scroll to Sensors and press SELECT.4. Scroll to <Add New> and press SELECT.5. Scroll to the type of Sensor (Open/Close) and press SELECT6. Wait 5 seconds before clipping the Sensor into the Bracket. You will then have 30 seconds to complete the installation. The display shows the time remaining.NOTE: DO NOT CLIP THE SENSOR INTO THE BRACKET UNTIL THE BRACKET AND MAGNET ARE INSTALLED ON THE DOOR OR WINDOW. NOTE: Insufficient Mounting Space: If your door frame does not provide enough room for mounting the Bracket, you may need to use a Sensor Extension.Metal Doors and Windows: If your are mounting a Magnet to a metal door or metal window, install a Spacer under the Magnet to maintain performance.7. Clip the Sensor into the Bracket. The Handset will beep when the system nds the Sensor. This may take a few seconds.8. Press OK9. Edit Sensor Name (Optional)You may change the name now or at a later time.• To change the Sensor Name, press the DELETE key to remove the default name.• Using the keys on your Handset keypad, type in the desired name. Press OK when complete. 10. Sensor Placement: Scroll to Door or Window. Press OK.11. Alarm Type: Scroll to Stay & Away, Away Only, or Convenience. Press OK.Stay and Away means the Sensor will be monitored in both Armed Stay and Armed Away modes (i.e. an exterior door). Away Only means the Sensor will be monitored only in Armed Away mode (i.e. an interior door). Convenience means the Sensor is only used for text messaging (like a liquor cabinet). 12. Sensor Extension: Scroll to Sensor Only, Extension, or Both. Press OK.NOTE: If your window frame does not provide enough room for mounting the Bracket, you may need to use a Sensor Extension. See the Sensor Extension Section in the User Guide.For standard Sensor installation with the Magnet next to the Sensor, select “Sensor Only.” A Sensor Extender is only required if space does not permit the Sensor to be placed next to the Magnet. In this case, use the Sensor Extension pictured below. You may also use the Sensor to monitor two windows by selecting Both. In this case, the Sensor monitors both a Magnet next to the Sensor and another Magnet next to the Sensor Extension.Sensor ExtensionSensor Not Found/Sensor Not AddedIf your system cannot detect a Sensor that you are trying to add, the Handset or Consol will display:If this occurs, follow the steps below:1. Isolate Sensor: Remove the Sensor from the Bracket and add a different Sensor to the same Bracket. You can obtain more troubleshooting instructions in the Troubleshooting Section of the User Guide.If additional Sensors do not work, proceed to Step 3.2. Re-Position the Sensor & Bracket: Reset the Sensor (as shown above) then move the Bracket and Magnet to a new location (perhaps just a few inches) up, down or along the door window frame and retry.3. Move Grid Controller: Move one of your Grid Controllers (Console, Base or Grid Extender) closer to this Sensor mounting location. The most practical type of Grid Controller to re position is most likely the Grid Extender.

Navigation menu