Leap Devices JR2TX1 RadioPopper User Manual

Leap Devices, LLC RadioPopper

User Manual

Jr2 TransmitterQuick Start GuideClick1 2 3 4 PP Button- Press and hold to power on/o- Tap to test reLighting Power LevelsThe Jr2 Transmitter is the most intuitive and easy to use lighting control device available.Click the dial inward to index between active groups. Turn dial to adjust value when frame is around desired group.When all groups are framed, all groups may be adjusted at the same time by the same value.When the lock is selected, any accidental movement of dial will not adjust power levels.Adjust Menu SettingsPRESS and HOLD dial to enter menu mode.Click dial to move between optionsRotate dial to make selectionChannel: Set RadioPopper channel 1 to 16Stops: Adjust by 1/3 or 1/10 stops. In percent mode, this changes between 1% and 5% adjustment intervals.Each group can be set to adjust by linear percent (similar to a JrX Transmitter dial) or more accurately by EV stops.SAVE and Recall SettingsThe Jr2 Transmitter includes 4 memory loca-tions to be used to store 4 complete lighting setups including all values and settings.Stored information includes the %/EV setting of each group, which groups are active, and whether the unit is set for 1/10 stop or 1/3 stop adjustments.The RadioPopper radio channel (1-16) is not stored in the memory locations.How to Save/RecallTo save your present settings to a given memory location, simply press and hold the group button (1~4) corresponding to the memory location. After 2 seconds the word “SAVE” will blink along with the chosen location. Your settings are now stored.To recall previously saved settings, press and hold Dial inward for 2 seconds. While the “SAVE” icon is blinking, press and hold the group button (1~4) for 1 second corresponding to the memory location you wish to recall. Your set-tings will be recalled from the memory location.1~4 Buttons- Toggle group on/o- Save/Recall SAVE settingsDial- Press and hold for MENU- Click to index, Rotate to set valueTRANSMITTER Jr21 2 3 4 P
FCC STATEMENTThis equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:* Reorient or relocate the receiving antenna.* Increase the separation between the equipment and receiver.* Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.* Consult the dealer or an experienced radio/TV technician for help.Operation with non-approved equipment is likely to result in interference to radio and TV reception. The user is cautioned that changes and modications made to the equipment without the approval of manufacturer could void the user’s authority to operate this equipment.FCC ID: V4TJR2TX1This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference and(2) this device must accept any interference received, including interference that may cause undesired operation.Important Note: To comply with FCC RF exposure compliance requirements, the following antenna installation and device operating congurations must be satised - This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. INDUSTRY CANADA INFORMATIONThis device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.Jr2 Receiver will adjust the associated light as nely as possible for the given light.When using the % scale, setting increments to 1/10 will allow power adjustment of 1% per increment. Setting increments to 1/3 will allow power adjustment of 5% per increment.using the % scale, a range from 00% to 99% is available. This scale is useful for users already familiar with the older model JrX Transmitter. Adjusting from 0% to 99% may be thought of as turning the dial of a JrX Transmitter between the high and low limits of the dial. Similarly, this % scale may be thought of as adjusting the power control slider of an Alien Bee light from one end to the other.To take advantage of the stop-accurate EV scale adjustment, a Jr2 Receiver is required. The older model JrX Receiver may still be used with the Jr2 Transmitter if you select the % scale for adjustment.1/3 and 1/10 IncrementsYou may choose to make adjustments in 1/3 stop intervals or 1/10 stop intervals.When the Jr2 Transmitter is congured to 1/3 stop increments and the group is set to EV mode, the 1/3 intervals will be approximated by setting to 0.7 and 0.3 increments. For example, starting at maximum power and adjusting downward, the settings will be 9.0, 8.7, 8.3, 8.0, and so on. When set to 1/10 stop increments, more ne control is possible. Con-sider however that some lighting devices are unable to adjust to 1/10 stop increments. The EV and % Scale SelectionEach of the 4 groups may be independently set to EV scale or % scale.When set to EV scale, the “maximum” power of the remote lights will be indicated by 9.0. Output power will decrease as this number decreases, one stop per EV. Note that some lights may not have the ability to adjust down more than a few stops, so at some point, further reduction of EV value may not reduce light output power any further depending on the light you are using. When SpecicationsBattery:2 x “AAA” Batteries. Rechargeable approved.Battery Life:50+ hours continual running time. (Depending on battery type and quality)Radio Frequency:902-928 MHz, ISM BandRadio Range:Up to 1750 ft depending on conditions and environment.Maximum Sync Speed: 1/500 for cameras having leaf shutters.

Navigation menu