Laird Connectivity 1002 SaBLE-x User Manual Rev 1

LS Research, LLC SaBLE-x Rev 1

Contents

User Manual Rev 1

SaBLE-x Module DATASHEET The information in this document is subject to change without notice. 330-0166 Copyright © 2015 LSR Page 1 of 14 SaBLE-xTM Bluetooth® Smart (BLE) Module FEATURES • Built in CC2640F128 Bluetooth Smart (BLE 4.1) System-On-Chip (SOC) • 128 kB Flash / 20 kB SRAM • RF Output Power: +5 dBm • RF Receive Sensitivity: -96 dBm • Size: 11.6mm x 17.9mm x 2.4mm • Operating Voltage: 1.8V to 3.8V • Operating Temperature: -40 to +85C • 9.1mA Transmit Mode (+5 dBm) • 6.1mA Receive Mode • 1μA Standby (SRAM/CPU retention and RTC running) with quick 100 μs start up • 200nA Shutdown • 61μA/MHz Active CPU Current • Drivers, Bluetooth Low Energy Controller, and bootloader in ROM • Flexible peripheral set • On board 32 kHZ and 24 MHz Crystals. • Worldwide Acceptance: FCC (USA), IC (Canada), ETSI (Europe), Giteki (Japan), C-Tick (AU/NZ) • REACH and RoHS compliant APPLICATIONS • Consumer electronics • Mobile phone accessories • Sports & Fitness equipment • HID applications • Home and Building Automation, Lighting Control, Alarm and Security • Electronic Shelf Labeling, Proximity Tags DESCRIPTION LSR would like to announce a low-cost and low-power consumption module which has all of the Bluetooth Smart 4.1 functionalities. The SaBLE-x module fully supports the single mode Bluetooth Low Energy operation, and the output power can support class 2. The module provides the ability to either put your entire application into the integrated ARM Cortex M3 microcontroller, or use the module in Network Processor mode in conjunction with the microcontroller of your choice. RF Core’s dedicated ARM Cortex M0 improves system performance and frees up FLASH memory for custom applications. Need to get to market quickly? Not an expert in Bluetooth Low Energy? Need a custom antenna? Do you need help with your host board? LSR Design Services will be happy to develop custom hardware or software, or help integrate the design. Contact us at sales@lsr.com or call us at 262-375-4400.
SaBLE-x Module DATASHEET The information in this document is subject to change without notice. 330-0166 Copyright © 2015 LSR Page 2 of 14 TABLE OF CONTENTS FEATURES .......................................................................................................................... 1 APPLICATIONS ................................................................................................................... 1 DESCRIPTION ..................................................................................................................... 1 FOOTPRINT AND PIN DEFINITIONS.................................................................................. 3 PIN DESCRIPTIONS ............................................................................................................ 4 ELECTRICAL SPECIFICATIONS ........................................................................................ 5 Absolute Maximum Ratings ....................................................................................................................... 5 Recommended Operating Conditions ...................................................................................................... 5 General Characteristics .............................................................................................................................. 5 DC Characteristics ...................................................................................................................................... 6 General Power Consumption ..................................................................................................................... 7 AGENCY CERTIFICATIONS ............................................................................................... 8 AGENCY STATEMENTS ..................................................................................................... 8 Federal Communication Commission Interference Statement .............................................................. 8 Industry Canada Statements...................................................................................................................... 9 OEM RESPONSIBILITIES TO COMPLY WITH FCC AND INDUSTRY CANADA REGULATIONS ....................................................................................................... 10 OEM LABELING REQUIREMENTS FOR END-PRODUCT .............................................. 11 OEM END PRODUCT USER MANUAL STATEMENTS.................................................... 12 EUROPE ............................................................................................................................ 13 CE Notice ................................................................................................................................................... 13 Declaration of Conformity (DOC) ............................................................................................................ 13 CONTACTING LSR............................................................................................................ 14
SaBLE-x Module DATASHEET The information in this document is subject to change without notice. 330-0166 Copyright © 2015 LSR Page 3 of 14 FOOTPRINT AND PIN DEFINITIONS 1 33 2 32 3 31 4 30 5 29 6 28 7 34 37 27 8 26 9 35 38 25 10 24 11 36 39 23 12 22 13 14 15 16 17 18 19 20 21 Figure 1 SaBLE-x Module Footprint (Viewed From Top)
SaBLE-x Module DATASHEET The information in this document is subject to change without notice. 330-0166 Copyright © 2015 LSR Page 4 of 14 PIN DESCRIPTIONS Module Pin Name I/O Type Description 1 RF OUT RF ANTENNA, 50 OHMS 2 GND GND GROUND 3 GND GND GROUND 4 NC - NO CONNECT (DO NOT CONNECT) 5 NC - NO CONNECT (DO NOT CONNECT) 6 /RESET DI ACTIVE LOW RESET. 100kΩ PULL-UP 7 JTAG TCKC DI/DIO JTAG TCKC 8 JTAG TMSC DIO JTAG TMSC 9 NC - NO CONNECT (DO NOT CONNECT) 10 NC - NO CONNECT (DO NOT CONNECT) 11 VCC PI POWER SUPPLY TO MODULE 12 VCC PI POWER SUPPLY TO MODULE 13 DIO 5/JTAG TDO DIO GPIO, JTAG TDO, ULP SENSOR INTERFACE, LED DRIVING CAPABILITY 14 DIO 6/JTAG TDI DIO GPIO, JTAG TDI, ULP SENSOR INTERFACE, LED DRIVING CAPABILITY 15 DIO 4 DIO GPIO, LED DRIVING CAPABILITY 16 DIO 3 DIO GPIO, LED DRIVING CAPABILITY 17 DIO 2 DIO GPIO, ULP SENSOR INTERFACE, LED DRIVING CAPABILITY 18 DIO 1/BOOT RX DIO GPIO, ULP SENSOR INTERFACE, BOOTLOADER RX (UART0) 19 DIO 0/BOOT TX DIO GPIO, ULP SENSOR INTERFACE, BOOTLOADER TX (UART0) 20 DIO 7 DIO GPIO, ANALOG INPUT, ULP SENSOR INTERFACE 21 DIO 8 DIO GPIO, ANALOG INPUT, ULP SENSOR INTERFACE 22 GND GND GROUND 23 DIO 10 DIO GPIO, ANALOG INPUT, ULP SENSOR INTERFACE 24 DIO 9 DIO GPIO, ANALOG INPUT, ULP SENSOR INTERFACE 25 NC - NO CONNECT (DO NOT CONNECT) 26 NC - NO CONNECT (DO NOT CONNECT) 27 NC - NO CONNECT (DO NOT CONNECT) 28 NC - NO CONNECT (DO NOT CONNECT) 29 DIO 11 DIO GPIO, ANALOG INPUT, ULP SENSOR INTERFACE 30 DIO 12 DIO GPIO, ANALOG INPUT, ULP SENSOR INTERFACE 31 DIO 13 DIO GPIO, ANALOG INPUT, ULP SENSOR INTERFACE 32 DIO 14 DIO GPIO, ANALOG INPUT, ULP SENSOR INTERFACE 33 GND GND GROUND 34-39 GND GND GROUND AND THERMAL RELIEF PADS PI = Power Input GND = Ground DI = Digital Input DO = Digital Output DIO = Digital Input/Output AI = Analog Input RF = Bi-directional RF Port Note: See the Texas Instruments CC2640 datasheet and user guide for further details on the I/O. Table 1 SaBLE-x Pin Descriptions
SaBLE-x Module DATASHEET The information in this document is subject to change without notice. 330-0166 Copyright © 2015 LSR Page 5 of 14 ELECTRICAL SPECIFICATIONS Absolute Maximum Ratings Symbol Description Min Max Unit VCC Digital Input Supply Voltage -0.3 4.1 V Voltage on any digital pin -0.3 VCC+0.3, max 4.1 V Input RF level +5 dBm Table 2 Absolute Maximum Ratings1 Recommended Operating Conditions Test conditions: Ambient Temp = 25°C Symbol Min Typ Max Unit VCC 1.8 3.3 3.8 V Table 3 Recommended Operating Conditions General Characteristics Characteristic Description Model Name SaBLE-x Product Description Bluetooth Low Energy Wireless Module Dimension 11.63 mm x 17.86 mm x 2.4 mm (W*L*T) Operating temperature -40°C to 85°C Storage temperature -40°C to 85°C Humidity Operating Humidity 10% to 95% Non-Condensing Storage Humidity 5% to 95% Non-Condensing Weight 0.75g +/- 0.05g Table 4 General Characteristics 1 Under no circumstances should exceeding the ratings specified in the Absolute Maximum Ratings section be allowed. Stressing the module beyond these limits may result permanent damage to the module that is not covered by the warranty.
SaBLE-x Module DATASHEET The information in this document is subject to change without notice. 330-0166 Copyright © 2015 LSR Page 6 of 14 DC Characteristics Parameter Test Conditions Min Typ Max Unit Input low-to-high transition with hysteresis Transition from 01, TA= 25C, VCC=1.8V 1.07 V Input high-to-low transition with hysteresis Transition from 10, TA= 25C, VCC=1.8V .74 V Input hysteresis Difference between 01 and 10. .33 V Input low-to-high transition with hysteresis Transition from 01, TA= 25C, VCC=3.8V 1.94 V Input high-to-low transition with hysteresis Transition from 10, TA= 25C, VCC=3.8V 1.54 V Input hysteresis Difference between 01 and 10. .4 V Logic-0 output voltage, 4 mA pins Output load 4 mA, TA= 25C, VCC=1.8V .26 V Logic-1 output voltage, 4 mA pins Output load 4 mA, TA= 25C, VCC=1.8V 1.54 V Logic-0 output voltage, 8 mA pins Output load 8 mA, TA= 25C, VCC=1.8V .21 V Logic-1 output voltage, 8 mA pins Output load 8 mA, TA= 25C, VCC=1.8V 1.58 V Logic-0 output voltage, 4 mA pins Output load 4 mA, TA= 25C, VCC=3.0V .33 V Logic-1 output voltage, 4 mA pins Output load 4 mA, TA= 25C, VCC=3.0V 2.72 V Logic-0 output voltage, 8 mA pins Output load 8 mA, TA= 25C, VCC=3.0V .28 V Logic-1 output voltage, 8 mA pins Output load 8 mA, TA= 25C, VCC=3.0V 2.68 V Input pullup current Vpad=0V, TA= 25C, VCC=1.8V 72 uA Input pulldown current Vpad=1.8V, TA= 25C, VCC=1.8V 22 uA Input pullup current Vpad=0V, TA= 25C, VCC=3.8V 277 uA Input pulldown current Vpad=3.8V, TA= 25C, VCC=3.8V 113 uA Table 5 SaBLE-x Module Bluetooth General DC Characteristics
SaBLE-x Module DATASHEET The information in this document is subject to change without notice. 330-0166 Copyright © 2015 LSR Page 7 of 14 General Power Consumption TA = 25°C and VCC = 3 V Parameter Test Conditions Min Typ Max Unit Shutdown No clocks running, no data retention 200 nA Standby 1 With RTC, CPU, RAM and partial register retention. XOSC_LF 1.2 uA Standby 2 With Cache, RTC, CPU, RAM and partial register retention. XOSC_LF 2.7 uA Idle Supply Systems and RAM powered. 550 uA Active Core running CoreMark 1.45mA + 31uA/MHz Radio Receive 6.1 mA Radio Transmit +5 dBm output power 9.1 mA Table 6 SaBLE-x Module Bluetooth Power Consumption Specifications
SaBLE-x Module DATASHEET The information in this document is subject to change without notice. 330-0166 Copyright © 2015 LSR Page 8 of 14 AGENCY CERTIFICATIONS FCC ID: TFB-1002, 15.247 IC ID: 5969A-1002, RSS 210 CE: Compliant to standards EN 60950-1, EN 300 328, and EN 301 489 AGENCY STATEMENTS Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This portable transmitter with its antenna complies with FCC/IC RF exposure limits for general population / uncontrolled exposure. FCC CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
SaBLE-x Module DATASHEET The information in this document is subject to change without notice. 330-0166 Copyright © 2015 LSR Page 9 of 14 Industry Canada Statements This device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. This device has been designed to operate with the antenna(s) listed below, and having a maximum gain of 0 dBi (PCB Trace), 2.0 dBi (LSR 2.4 GHz Dipole), 2.0 dBi (LSR 2.4 GHz FlexPIFA), and 2.0 (LSR 2.4 GHz FlexNotch). Antennas not included in this list or having a gain greater than 0 dB, 2.0 dBi, 2.0 dBi, and 2.0 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. List of all Antennas Acceptable for use with the Transmitter 1) On module PCB trace antenna. 2) LSR 001-0001 center-fed 2.4 GHz dipole antenna and LSR 080-0001 U.FL to Reverse Polarity SMA connector cable. 3) LSR 001-0014 2.4 GHz FlexPIFA antenna. 4) LSR 001-0015 2.4 GHz FlexNotch antenna. Cet appareil est conforme aux normes d'Industrie Canada exempts de licence RSS (s). L'opération est soumise aux deux conditions suivantes: (1) cet appareil ne peut pas provoquer d'interférences et (2) cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil. Pour réduire le risque d'interférence aux autres utilisateurs, le type d'antenne et son gain doiventêtre choisis de manière que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pascelle permise pour une communication réussie. Cet appareil a été conçu pour fonctionner avec l'antenne (s) ci-dessous, et ayant un gain maximum de 0 dBi (PCB Trace), 2,0 dBi (LSR 2.4 GHz Dipole), 2,0 dBi (LSR 2.4 GHz FlexPIFA), et 2,0 dBi (LSR 2.4 GHz FlexNotch). Antennes pas inclus dans cette liste ou présentant un gain supérieur à 0 dB, 2,0 dBi, 2,0 dBi, et 2,0 dBi sont strictement interdites pour une utilisation avec cet appareil. L'impédance d'antenne requise est de 50 ohms. Liste de toutes les antennes acceptables pour une utilisation avec l'émetteur 1) Le module d'antenne PCB trace. 2) LSR 001-0001 centre-fed 2,4 GHz antenne dipôle et LSR 080-0001 U.FL pour inverser câble connecteur SMA à polarité. 3) LSR 001-0014 antenne FlexPIFA 2,4 GHz. 4) LSR 001-0015 antenne FlexNotch 2,4 GHz.
SaBLE-x Module DATASHEET The information in this document is subject to change without notice. 330-0166 Copyright © 2015 LSR Page 10 of 14 OEM RESPONSIBILITIES TO COMPLY WITH FCC AND INDUSTRY CANADA REGULATIONS The SaBLE-xModule has been certified for integration into products only by OEM integrators under the following conditions: The antennas for this transmitter must not be co-located with any other transmitters except in accordance with FCC and Industry Canada multi-transmitter procedures. Co-location means having a separation distance of less than 20 cm between transmitting antennas. As long as the two conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for certain configurations or co-location with another transmitter), then the FCC and Industry Canada authorizations are no longer considered valid and the FCC ID and IC Certification Number cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC and Industry Canada authorization. Le module de SaBLE-xa été certifié pour l'intégration dans des produits uniquement par des intégrateurs OEM dans les conditions suivantes: Les antennes pour ce transmetteur ne doit pas être co-localisés avec les autres émetteurs sauf en conformité avec la FCC et Industrie Canada multi-émetteur procédures. Co-localisation des moyens ayant une distance de séparation inférieure à 20 cm entre les antennes d'émission. Tant que les deux conditions précitées sont réunies, les tests de transmetteurs supplémentaires ne seront pas tenus. Toutefois, l'intégrateur OEM est toujours responsable de tester leur produit final pour toutes les exigences de conformité supplémentaires requis avec ce module installé (par exemple, les émissions appareil numérique, les exigences de périphériques PC, etc.) NOTE IMPORTANTE: Dans le cas où ces conditions ne peuvent être satisfaites (pour certaines configurations ou de co-implantation avec un autre émetteur), puis la FCC et Industrie autorisations Canada ne sont plus considérés comme valides et l'ID de la FCC et IC numéro de certification ne peut pas être utilisé sur la produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'un distincte de la FCC et Industrie Canada l'autorisation.
SaBLE-x Module DATASHEET The information in this document is subject to change without notice. 330-0166 Copyright © 2015 LSR Page 11 of 14 OEM LABELING REQUIREMENTS FOR END-PRODUCT The SaBLE-x module is labeled with its own FCC ID and IC Certification Number. The FCC ID and IC certification numbers are not visible when the module is installed inside another device, as such the end device into which the module is installed must display a label referring to the enclosed module. The final end product must be labeled in a visible area with the following: “Contains Transmitter Module FCC ID: TFB-1002” “Contains Transmitter Module IC: 5969A-1002” or “Contains FCC ID: TFB-1002” “Contains IC: 5969A-1002” The OEM of the SaBLE-x module must only use the approved antenna(s) listed above, which have been certified with this module. Le module de SaBLE-x est étiqueté avec son propre ID de la FCC et IC numéro de certification. L'ID de la FCC et IC numéros de certification ne sont pas visibles lorsque le module est installé à l'intérieur d'un autre appareil, comme par exemple le terminal dans lequel le module est installé doit afficher une etiquette faisant référence au module ci-joint. Le produit final doit être étiqueté dans un endroit visible par le suivant: “Contient Module émetteur FCC ID: TFB-1002" “Contient Module émetteur IC: 5969A-1002" ou “Contient FCC ID: TFB-1002" “Contient IC: 5969A-1002" Les OEM du module SaBLE-x ne doit utiliser l'antenne approuvée (s) ci-dessus, qui ont été certifiés avec ce module.
SaBLE-x Module DATASHEET The information in this document is subject to change without notice. 330-0166 Copyright © 2015 LSR Page 12 of 14 OEM END PRODUCT USER MANUAL STATEMENTS The OEM integrator should not provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product. Other user manual statements may apply. L'intégrateur OEM ne devraient pas fournir des informations à l'utilisateur final sur la façon d'installer ou de supprimer ce module RF ou modifier les paramètres liés RF dans le manuel utilisateur du produit final. Autres déclarations manuel de l'utilisateur peuvent s'appliquer.
SaBLE-x Module DATASHEET The information in this document is subject to change without notice. 330-0166 Copyright © 2015 LSR Page 13 of 14 EUROPE CE Notice This device has been tested and certified for use in the European Union. See the Declaration of Conformity (DOC) for specifics. If this device is used in a product, the OEM has responsibility to verify compliance of the final product to the EU standards. A Declaration of Conformity must be issued and kept on file as described in the Radio and Telecommunications Terminal Equipment (R&TTE) Directive. The ‘CE’ mark must be placed on the OEM product per the labeling requirements of the Directive. Declaration of Conformity (DOC) The DOC can be downloaded from the LSR Wiki.
SaBLE-x Module DATASHEET The information in this document is subject to change without notice. 330-0166 Copyright © 2015 LSR Page 14 of 14 CONTACTING LSR Headquarters LSR W66 N220 Commerce Court Cedarburg, WI 53012-2636 USA Tel: 1(262) 375-4400 Fax: 1(262) 375-4248 Website www.lsr.com Technical Support forum.lsr.com Sales Contact sales@lsr.com The information in this document is provided in connection with LS Research (hereafter referred to as “LSR”) products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of LSR products. EXCEPT AS SET FORTH IN LSR’S TERMS AND CONDITIONS OF SALE LOCATED ON LSR’S WEB SITE, LSR ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL LSR BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF LSR HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. LSR makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. LSR does not make any commitment to update the information contained herein. Unless specifically provided otherwise, LSR products are not suitable for, and shall not be used in, automotive applications. LSR’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.

Navigation menu