LITE ON TECHNOLOGY CR8702K JUKEBLOX NETWORKED MEDIA MODULE User Manual

LITE-ON Technology Corp. JUKEBLOX NETWORKED MEDIA MODULE Users Manual

Users Manual

Data Sheet: CR Series JukeBlox Networked Media Modules dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 1 of 15 JukeBlox Networked Media Module CR Series CR870-2KDatasheetComplete audio networking system on a small module Integrated Ethernet + USB2.0 WiFi-certified 802.11b/g (optional) Built-in PIFA antenna DAB radio receiver (optional) Glueless audio, video and control ports FCC certified CONFIDENTIAL
Data Sheet: CR Series JukeBlox Networked Media Modules dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 2 of 15 IntroductionThe CR-series module is a single-board networked media player module, based on BridgeCo’s DM860 and DM870 media processors, and enables fast product developments with Ethernet, USB and optional WiFi and/or DAB radio connectivity. The module connects to standard legacy components in various audio, video/LCD and control formats. Block Diagram Ethernet PHYDM860orDM870256 MbitSDRAMJTAGRJ-45100B-TMemUSBGPIO24.000 MHzReset InNAND 1 GBNAND flash802.11RF amp(optional)802.11RMIISPIRTC 32.768 kHzUSB(Host)USBRSTUART5V3.3VJukeBlox Networked Media Module – CR SeriesReset Out1.2VStereo OutVideo OutAudio I/O4/8bit MMC3x6bit RGB2 x UARTSPI Ctrl.max. 20 GPIOs3.3V (RTC)SuperCapIR sensorreset signalsanalog muteI2C busshift registerIC controlserial controlA/D, D/AS/PDIFCCIR-656LP 2HP outDisplaySD-CardAVPortsLCDSSMDACPIFAAntennaSwitcher 1.9VAVPorts DAB
Data Sheet: CR Series JukeBlox Networked Media Modules dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 3 of 15 OverviewTop View of CR870-2A version Bottom View of CR870-2A version PIFAantenna802.11b/gfront-end BridgeCoprocessorEthernetDABFLASH(optional socket) SDRAMantennaconnectorMedia connectorDABconnectorLCDconnector
Data Sheet: CR Series JukeBlox Networked Media Modules dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 4 of 15 Top View of CR870-2G version Bottom View of CR870-2B, CR870-2C, CR870-2G versions Please note that production version does not have exposed solder on the underside of the mounting holes.
Data Sheet: CR Series JukeBlox Networked Media Modules dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 5 of 15 Ordering Guide Part Number BridgeCo ICs WiFi Ethernet USB Real-Time Clock DAB / DAB+ / DMB Audio LCD PIFAAntenna Ext.Antenna UFL Conn. SDRAM No on-board 1.9V Contains shield Incl.connector Incl.connector CR870-2A DM870+T6201 X X X X X X X (X)* 32MB CR870-2B DM870+T6201 X X X X 32MB CR870-2C DM870+T6201 X X X 32MB CR870-2D DM870+T6201 X X X X X 32MB CR870-2F DM870+T6201 X X X X X X (X)* 32MB CR870-2G DM870+T6201 X X X X 32MB CR870-2H DM870+T6201 X X X X (X)* 16MB CR870-2I DM870+T6201 X X X 16MB CR870-2J DM870+T6201 X X X 16MB CR870-2K DM870+T6201 X X X 16MB X CR860-2A DM860 n/a X X n/a 32MB CR860-2B DM860 n/a X X X X n/a 32MB * Connector on board, but not enabled Electrical Specifications Parameter State Model Component Voltage Symbol min. typ. max. UnitsMain VIN +2.97+1.08+3.3+1.2+3.63 +1.32 VVInput Voltage DAB VIN+1.62+2.97+1.35+1.8+3.3+1.5+1.98 +3.63 +1.65 VVV3.3V PIN3.3 - 230 300 mW CR870 int 1.9V 1.2V PIN1.2 - 45 60 mW 3.3V PIN3.3 - 165 215 mW 1.2V PIN1.2 - 45 60 mW CR870 ext 1.9V 1.9V PIN1.9 - 35 50 mW 3.3V PIN3.3 - 145 190 mW Reset StateCR860 1.2V PIN1.2 - 45 60 mW 3.3V PIN3.3 - 1750 2275 mW CR870 int 1.9V 1.2V PIN1.2 - 600 800 mW 3.3V PIN3.3 - 825 1075 mW 1.2V PIN1.2 - 600 800 mW WLAN Operating CR870 ext 1.9V 1.9V PIN1.9 - 535 700 mW 3.3V PIN3.3 - 760 990 mW PowerConsumption Operating CR860 Main1.2V PIN1.2 - 600 800 mW Note: The maximum power consumption values are 30% larger than the typical values. The maximum values are intended to be used for power supply sizing calculations.
Data Sheet: CR Series JukeBlox Networked Media Modules dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 6 of 15 Absolute Maximum Ratings Parameter Component Min Max Units3.3V Supply Voltage -0.5 4.6 V 1.2V Supply Voltage -0.5 1.8 V Logic Input Voltage -0.5 6 V Logic Output Voltage Main-0.5 4.6 V Operating Conditions Parameter Min Max UnitsOperating Temperature 0 +70 °C Operating Humidity 10 90 (non condensing) %RH Storage Temperature -10 +75 °C Storage Humidity 10 95 (non condensing) %RH Storage Temperature Cycle Test 24 hrs -10 +75 °C WiFi Specification (CR870 only) Feature Description WLAN Standards IEEE 802.11b IEEE 802.11g Frequency Band 2.412 – 2.472 GHz (2.4GHz ISM Band, 13 Channels) Channel 1 - Channel 13 North America, Japan Telec, Europe ETSI Modulation 802.11b mode (DS-SS: IEEE 802.11b) 802.11g mode (OFDM: IEEE 802.11g) Transmission Speed 802.11b mode 11Mbps, 5.5Mbps, 1Mbps 802.11g mode 54Mbps, 48Mbps, 36Mbps, 24Mbps, 18Mbps, 12Mbps, 9Mbps, 6Mbps Tx Power 802.11b mode (16.5dBm, +/-1dBm) 802.11g mode (21dBm, +/-1dBm) Power-on Ramp < 2us RF Carrier Suppression < 15dBc TX EVM < -5dB @ 6Mbps < -25dB @ 54Mbps Rx Sensitivity (incl. CE2 Mother board) 802.11b mode =<-88dBm @ 1Mbps, =<-85dBm @ 5.5Mbps, =<-83dBm @ 11Mbps 802.11g mode =<-86dBm @ 6Mbps, =<-75dBm @ 36Mbps, =<-69dBm @ 54Mbps Throughput Rate (measured for each module) See factory test specification
Data Sheet: CR Series JukeBlox Networked Media Modules dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 7 of 15 Regulatory compliance Description Country Compliance Electromagnetic Compatibility (Prescan) USAEuropeFCC CFR47 Part15B EN 55022 EN 55024 EN 61000-3-2 EN 61000-3-3 EN 61000-4-2 EN 61000-4-3 EN 61000-4-4 EN 61000-4-5 EN 61000-4-6 EN 61000-4-8 EN 61000-4-11 Radio Regulations (CM870 only) TBD TBD RoHSUses only RoHS compliant components Environmental Test Withstands 4 hours at 70°C, 90% RH ESD and Transient Test (Applies to LAN and USB external connections only) ESD: +/- 2kV operation, +/- 4kV no destruction (part of CE test) Fast electrical transients: +/- 500V operation, +/- 1000V no destruction (part of CE test) Magnetic Field Test Passes EN55022 and EN55024 (part of CE test) MTBF>10000 hours Mechanical Specifications Passes drop test according to I.E.C. 68-2-32, height 100 cm, 1 corner, 6 faces. Passes vibration test with sine, vertical, 60 minutes, 600 to 18000 cpm, 1G Module Quality Defect Rate: 7 months <0.5% failures, 14 months <1% failures AQL CR=0, MA=0.4, MI=0.4
Data Sheet: CR Series JukeBlox Networked Media Modules dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 8 of 15 Board Dimensions Top View and Side View Bottom View (showing connector locations) Note: 1. All dimensions are measured in millimetres (mm). 2. PCB’s thickness: 1.00 +/- 0.10mm 3. Tolerance: +/-0.10mm 4. Outline Tolerance: +/-0.10mm 5. NPTH Hole: +/-0.05mm 6. PTH Hole: +/-0.075mm 7. Connector positions, board dimensions, mounting hole positions and sizes are the same for all module variants.
Data Sheet: CR Series JukeBlox Networked Media Modules dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 9 of 15 Top and Side View of CR870-2G (no PIFA antenna) Module weight CR860: 25g CR870: 25g
Data Sheet: CR Series JukeBlox Networked Media Modules dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 10 of 15 ConnectorsWLAN UFL Antenna Connector (optional) One coaxial antenna connector is provided as an alternative to the built-in PIFA antenna. The choice between using the PIFA antenna or using the coaxial socket is a build option, determined by the position of a surface mount capacitor on the module PCB. Please see ordering guide for build option details. The surface-mount receptacle parts: Hirose U.FL-R-SMT (CL No. 331-0471-0) Coaxial antenna connector dimensions Module Connectors The CR860/870 module uses 3 female board-to-board connectors as interfaces to the product main board. The connectors needed on the product main board are male type, with the part numbers as shown in the table below. ConnectorNumberConnectorPurposeConnectorTypeNumberof Pins PinConfigurationMale Mating Connector Part NumbersJ1 LCD 30 2 x 15 x 0.5mm 14-5046-030-145-829+ (Kyocera) J2 Media 120 2 x 60 x 0.5mm 14-5046-120-145-829+ (Kyocera) J3 DAB B2BConnector 40 2 x 20 x 0.5mm 14-5046-040-145-829+ (Kyocera)
Data Sheet: CR Series JukeBlox Networked Media Modules dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 11 of 15 The pinout and signal names are shown on the next page. The following table provides an overview for the most important control and interface signals. Key Connections Signal(s) Connector ID PinNumber(s)Description J2 3, 4, 5, 6 Input voltage; +3.3V J2 9, 10, 11, 12 Input voltage; +1.2V J3 4, 6 Input voltage; +1.8V J3 10 Input voltage; +3.3V VINJ3 12 Input voltage; +1.5V SPI_DOUT SPI_DIN SPI_CLKSPI_NCS0, 1 J2 J2 J2 J2 25272930, 32 SPI bus from DM870’s SPI controller. SPI_REQ J2 64 PDOUT1 signal used as SPI_REQ for eDMP applications RXD1, TXD1 J2 35, 37 3.3V logic level UART I/Os for the debug UART. Provide external RS-232 transceiver to connect to a PC’s COM port. NRESET_MOD J2 34 Low-active input to reset the module; internal 10K pull-up NPD_RF J2 119 Low-active input to shut down the power for the 802.11 Rf part; internal 10K pull-up AOUTLP/AOUTLN J2 63, 65 AOUTRP/AOUTRN J2 60, 58 Differential stereo output from PWM-DAC. BIST activate J2 48 Low-active input to invoke the production BIST; DM870-internal pull-up Factory Reset J2 68 High-active input to reset the configuration; DM870-internal pull-downIR input J2 70 Infrared sensor input. This is a Schmitt-Trigger input and can handle interrupt inputs with slow slopes. ETH_NRESET J2 72 Low-active reset for the on-board Ethernet phy. This output is driven by the DM870 and is not suited for other purpose. SDA, SCL J2 73, 75 I2C bus created by GPIO-14 and GPIO-13. No internal pull-ups; if I2C is to be used, please add the proper external pull-up resistors. ETH_LED_ACT ETH_LED_SPEED J2 J2 1001023.3V push-pull outputs (max. ±12mA) to drive the Ethernet LEDs. A low-level indicates 100Mbps mode and activity respectively.
Data Sheet: CR Series JukeBlox Networked Media Modules dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 12 of 15 Detailed Connector PIN Descriptions J2 – Media Connector Function GPIO Signal IC PIN Power Power IC PIN Signal GPIO FunctionGND 1 2 GNDVIN (+3.3V) 3 4 VIN (+3.3V)VIN (+3.3V) 5 6 VIN (+3.3V)GND 7 8 GNDVIN (+1.2V) 9 10 VIN (+1.2V)VIN (+1.2V) 11 12 VIN (+1.2V)GND 13 14 GNDVIN_OUTSIDE (+1.9V) 15 16 VIN_OUTSIDE (+1.9V)GND 17 18 GNDF4 3V3RTC 19 20 GNDGND 21 22 B20 TMSGND 23 24 A20 TCKSPI_DOUT E17 25 26 B19 TDISPI_DIN F17 27 28 A19 TDOSPI_CLK D17 29 30 D16 SPI_NCS0TXD0 C17 31 32 D15 SPI_NCS1RXD0 A18 33 34 NRESET_MODRXD1 B17 35 36 B16 SSMD6 GPIO-10 SPI_E_CLKTXD1 A17 37 38 C15 SSMD4 GPIO-08 SPI_E_SDOGND 39 40 A15 SSMD2SPI_E_NCS GPIO-11 SSMD7 C16 41 42 C14 SSMD1SPI_E_SDI GPIO-09 SSMD5 A16 43 44 A14 SSMCMDSSMD3 B15 45 46 C11 SSMWPSSMD0 B14 47 48 M18 NCS3 GPIO-17 BIST activa teSSMCLK C13 49 50 L18 NCS2 GPIO-19SSMCP C12 51 52 GNDGND 53 54 USB_VBUSUSB_DN A1 55 56 GNDUSB_DP B1 57 58 K2 AOUTRNUSBVBUSDRV 59 60 J2 AOUTRPGND 61 62 GNDAOUTLP H3 63 64 L1 PDOUT1 GPIO-06 SPI_REQAOUTLN J3 65 66 L2 VCO1 GPIO-07GND 67 68 M1 PDOUT0 GPIO-04 Factory resetGPIO-16 A23 K20 69 70 M2 VCO0 GPIO-05 IR inputIRQ input GPIO-18 A22 K19 71 72 U3 AV3CLK GPIO-12 ETH NRESETI2C SDA GPIO-14 AV3CTRL1 V1 73 74 M3 AV0CTRL0I2C SCL GPIO-13 AV3CTRL0 V2 75 76 P3 AV1DATA3AV0CTRL2 K3 77 78 R1 AV1DATA2AV0CTRL1 L3 79 80 R2 AV1DATA1AV0CLK N1 81 82 R3 AV1DATA0AV0DATA3 N2 83 84 GNDAV0DATA2 N3 85 86 T1 AV2CTRL1 MCLKAV0DATA1 P1 87 88 GNDAV0DATA0 P2 89 90 R4 AV2CLK SCLKGND 91 92 GNDLRCK AV2CTRL0 T2 93 94 W2 AV4DATA1 SPDIF outputA/D data 1 AV2DATA3 T3 95 96 Y1 AV4DATA0 SPDIF inputA/D data 0 AV2DATA2 T4 97 98 GNDD/A data 1 AV2DATA1 U1 99 100 ETH_LED_ACTD/A data 0 AV2DATA0 U2 101 102 ETH_LED_SPEEDGND 103 104 Y14 MIICRS GPIO-00ETH_RX- 105 106 W14 MIICOL GPIO-01ETH_RX+ 107 108 V10 MIITXER GPIO-02ETH_CT 109 110 V11 MIITXCLK GPIO-03ETH_TX- 111 112 W10 MIITXD0ETH_TX+ 113 114 Y10 MIITXD1GND 115 116 W12 MIIRXD0GPIO-15 NWAIT N18 117 118 Y12 MIIRXD1NPD_RF 119 120 GNDPIN NumberSPIDebug UARTJTAGSPIUSBVideo OutputEthe rnetUSBVideo OutputEth e rn et
Data Sheet: CR Series JukeBlox Networked Media Modules dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 13 of 15 J1 – LCD Connector Function GPIO Signal IC PIN Power Power IC PIN Signal GPIO FunctionGND 12GNDLCDD0 Y7 34 W7 LCDD1LCDD2 V7 56 Y6 LCDD3LCDD4 W6 78 V6 LCDD5LCDD6 U6 910 Y5 LCDD7LCDD8 W5 11 12 V5 LCDD9LCDD10 U5 13 14 Y4 LCDD11LCDD12 W4 15 16 V4 LCDD13LCDD14 U4 17 18 Y3 LCDD15LCDD16 W3 19 20 Y2 LCDD17GND 21 22 GNDLCDCLK Y9 23 24 W9 LCDCTRL0LCDCTRL1 Y8 25 26 W8 LCDCTRL2LCDCTRL3 V8 27 28 GNDGND 29 30 GNDPIN NumberLCD InterfaceLCD InterfaceLCD InterfaceLCD InterfaceJ3 – DAB Connector Function GPIO Signal PNM3030E PIN Power Power PNM3030E PIN Signal GPIO FunctionGND 12GNDRESETB 30 34VIN (+1.8V)RF_I2C_CK 39 56VIN (+1.8V)I2C_SDA_DAB 378 40 RF_I2C_DTI2C_SCL_DAB 46 910VIN (+3.3V)GND 11 12 VIN (+1.5V)TEST_1 79 13 14 80 TEST_2DAB_SPI_MOSI 19 15 16 78 TEST_0DAB_SPI_CSB 17 17 18 18 DAB_SPI_CLKGND 19 20 16 DAB_SPI_MISOGND 21 22 GNDGND 23 24 14 INT_0GND 25 26 15 INT_1MPEG_ERR 427 28 47 MPEG_CLKMPEG_SYNC 529 30 48 MPEG_VALMPEG_DAT7 631 32 7MPEG_DAT6MPEG_DAT5 51 33 34 8MPEG_DAT4MPEG_DAT3 52 35 36 9MPEG_DAT2MPEG_DAT1 10 37 38 53 MPEG_DAT0GND 39 40 GNDPIN NumberSPISPIApplication Notes There are strict power sequencing and reset timing requirements. Please see DM870 IC data sheet, Sections 3.1 and 3.2, filename: dat_DM870_16_datasheet.pdf, or later version.
Data Sheet: CR Series JukeBlox Networked Media Modules dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 14 of 15 Revision Control Revision Date / Author Remarks V2.14 June 10, 2010 / SHs •Updated Frequency Band entry in “WiFi Specification” table V2.13 June 6, 2010 / SHs •Updated “Ordering Guide” table V2.12 May 27, 2010 / SHs •Updated TX EVM entry in “WiFi Specifications” table •Updated Power Consumption entries in “Electrical Specifications” table •Added Note to “Electrical Specifications” table •Removed box from “Bottom View of CR870-2C version” photo •Updated “Bottom View of CR870-2C version” title to “Bottom View of CR870-2B, CR870-2C, CR870-2G versions” •Added “Top View of CR870-2G version” photo •Updated “Top View” title to “Top View of CR870-2A version” •Updated “Bottom View” to “Bottom View of CR870-2A version” •Updated Notes in Board Dimensions section •Added “Top and Side View of CR870-2G” drawings •Updated Module Weight titles V2.11 April 25, 2010 / SHs •Updated Power Consumption/WLAN Operating entry in “Electrical Specifications” table V2.10 April 10, 2010 / SHs •Corrected “Module Connectors” section text to say “female board-to-board connectors” •Updated Module Connectors table with correct “Male” Mating Connector Part Numbers V2.9 March 22, 2010 / SHs •Renamed “WLAN Antenna Connectors” section to “WLAN UFL Antenna Connector” •In the “WLAN Antenna Connectors” table, “receptible” became “receptacle” •CR870-2G option and External Antenna UFL connector column added to Ordering Guide •Power Consumption values added to Electrical Specifications table •Added Absolute Maximum Ratings table •Added Application Notes section •NREST became NRESET_MOD for Pin 34 in Key Connections table •SPI_REQ row added to Key Connections table •SPI_REQ added to Function column of Pin 64 in J2-Media Connector table V2.8 Feb. 24, 2010 / SHs •Added “Bottom View of CR870-2C version” image to “Overview” section V2.7 Feb. 16, 2010 / SHs •Updated “Module Connectors” table V2.6 Feb. 15, 2010 / SHs •Updated “Ordering Guide” table V2.5 Feb. 10, 2010 / SHs •Updated “Ordering Guide” table •Added new coaxial text in “WLAN Antenna Connectors” section •Added manufacturer name to “Module Connectors” table V2.4 Feb. 08, 2010 / SHs •Updated Rx Sensitivity description in “WiFi Specification” table V2.3 Feb. 03, 2010 / SHs •“Key Connectors” table title changed to “Key Connections” •Updated entries in “Key Connections” table •Updated pins 1, 2, 25, 27, 58 & 60 in “J2 – Media Connector” table
Data Sheet: CR Series JukeBlox Networked Media Modules dat_CR860_CR870_2_14_datasheet.doc CONFIDENTIAL Version 2.14 – June 10th 2010 - Page 15 of 15 V2.2 Feb. 02, 2010 / SHs •Added new items to “WiFi Specification” table •Amended Block Diagram to show input of 1.2V instead of 1.8V V2.1 Jan. 04, 2010 / SHs •Updated header layout •Removed “CR860/CR870” from data sheet title •Left justified Key Features list on front page •New Ordering Guide table •Updated Module Weights V2.0 Jan. 02, 2010 / JWs and SHs•New header and footer layout •Fit front and back Overview images onto one page •Bulletise Revision Control table V1.1 Dec. 18, 2009 / SHs •Changed Core Module name to “JukeBlox Networked Media Module(CR Series)” •Front page revisions: removed front and back images of board; inserted angled image of board; moved Key Features list to front page •Moved Disclaimers page to end of document •Replaced previous board images (front and back) in Overview section with better quality images •Added box and label to BridgeCo processor in Overview images •Revised Ordering Guide •Reduced Board Dimension drawings to fit on one page •Added mating connector part numbers to Module Connectors section. V1.0 Dec. 9, 2009 / SHs Initial version © 2010 by BridgeCo Inc All rights reserved. This document is the sole property of BridgeCo. It contains information proprietary to BridgeCo. Reproduction or duplication by any means of any portion of this document without the prior written consent of BridgeCo is expressly forbidden. TrademarksThe names of products of BridgeCo or other vendors and suppliers appearing in this document may be trademarks or service marks of their respective owners which may be registered in some jurisdictions. Warranty Limitations BridgeCo assumes no responsibility for inaccuracies, errors, or omissions in this document. BridgeCo assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. Module Revision History To be determined.
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning "Industry Canada regulatory information Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. ""The user is cautioned that this device should be used only as specified within this manual to meet RF exposure requirements. Use of this device in a manner inconsistent with this manual could lead to excessive RF exposure conditions." IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions: - The antenna must be installed such that 20 cm is maintained between the antenna and users. Information To Be Supplied to the End User by the OEM or Integrator The following regulatory and safety notices must be published in documentation supplied to the end user of the product or system incorporating an adapter in compliance with local regulations. Host system must be labeled with "Contains FCCID:PPQ-CR8702K“, FCC ID displayed on label.

Navigation menu